Datasheet M185B1-L05 Datasheet (Chi Mei Optoelectronics)

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

TFT LCD Approval Specification

MODEL NO.: M185B1-L05

Customer:

Approved by:

Note:

www.jxlcd.com

記錄工作審核角色投票

2009-02-20

15:01:32 CST

PMMD II

Director

kevin_wu(吳柏勳

Director Accept

/56520/54894)

1 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

- CONTENTS -

REVISION HISTORY...............................................................................................................................3

1. GENERAL DESCRIPTION ..................................................................................................................4

1.1 OVERVIEW

1.2 FEATURES

1.3 APPLICATION

1.4 GENERAL SPECIFICATIONS

1.5 MECHANICAL SPECIFICATIONS

2. ABSOLUTE MAXIMUM RATINGS.......................................................................................................5

2.1 ABSOLUTE RATINGS OF ENVIRONMENT

2.2 ELECTRICAL ABSOLUTE RATINGS

2.2.1 TFT LCD MODULE

2.2.2 BACKLIGHT UNIT

3. ELECTRICAL CHARACTERISTICS....................................................................................................7

3. 1.1 TFT LCD MODULE

3.1.2 Vcc Power Dip Condition:

3.2 BACKLIGHT UNIT

4. BLOCK DIAGRAM...............................................................................................................................11

4.1 TFT LCD MODULE

4.2 BACKLIGHT UNIT

5. INPUT TERMINAL PIN ASSIGNMENT................................................................................................12

5.1 TFT LCD MODULE

5.2 LVDS DATA MAPPING T ABLE

5.3 BACKLIGHT UNIT

5.4 COLOR DATA INPUT ASSIGNMENT

6. INTERFACE TIMING ...........................................................................................................................15

6.1 INPUT SIGNAL TIMING SPECIFICATIONS

6.2 POWER ON/OFF SEQUENCE

7. OPTICAL CHARACTERISTICS...........................................................................................................17

7.1 TEST CONDITIONS

7.2 OPTICAL SPECIFICATIONS

8. PACKAGING........................................................................................................................................20

8.1 PACKING SPECIFICATIONS

8.2 PACKING METHOD

9. DEFINITION OF LABELS....................................................................................................................22

10. PRECAUTIONS.................................................................................................................................23

10.1 ASSEMBLY AND HANDLING PRECAUTIONS

10.2 SAFETY PRECAUTIONS

10.3 SAFETY STANDARDS

10.4 OTHERS

11. MECHANICAL CHARACTERISTICS.................................................................................................24

www.jxlcd.com

2 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

REVISION HISTORY

Version Date Section Description

Ver 2.0

Feb,09, 09’

www.jxlcd.com

M185B1-L05 Approval specification was first issued.

www.jxlcd.com

3 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

1. GENERAL DESCRIPTION

1.1 OVERVIEW

M185B1-L05 is a 18.5” TFT Liquid Crystal Display module with 2 CCFL Backlight unit and 30pin 1ch-LVDS interface. This module supports 1366 x 768 WXGA mode and can display up to 16.7M colors. The inverter module for Backlight is not built in.

1.2 FEATURES

- Contrast ratio 1000:1

- Response time 5ms.

- Brightness 250nits

- Color saturation NTSC 72%.

- WXGA (1366 x 768 pixels) re solution.

- DE (Data Enable) only mode.

- LVDS (Low Voltage Differential Signaling) interface.

- RoHS compliance.

1.3 APPLICA TION

- TFT LCD Monitor

www.jxlcd.com

1.4 GENERAL SPECIFICATI0NS

Bezel Opening Area 413.4(H) x 234 (V) mm

Transmissive Mode Normally White - -

Module Power Consumption 13.85 Watt (2)

www.jxlcd.com

Item Specification Unit Note

Active Area 409.8 (H) × 230.4(V) (18.5” diagonal) mm

Driver Element a-Si TFT active matrix - -

Pixel Number 1366 x R.G.B. x 768 pixel -

Pixel Pitch 0.3 (H) x 0.3 (V) mm -

Pixel Arrange ment RGB vertical stripe - -

Display Colors 16.7M color -

Surface Treatment Glare type, 3H hard coating - -

(1)

1.5 MECHANICAL SPECIFICATIONS

Item Min. Typ. Max. Unit Note

Horizontal(H) 429.87 430.37 430.87 mm

Module Size

Note (1) Please refer to the attached drawings for more information of front and back outline dimensions. Note (2) Please refer to sec. 3.1 & 3.2 in this document for more information of power consumption.

Vertical(V) 254.1 254.6 255.1 mm

Depth(D) 15.75 16.25 16.75 mm

Weight - 1965 2000 g -

4 / 26

(1)

Version 2.0

Doc No.: 400029638

A

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

2. ABSOLUTE MAXIMUM RATINGS

2.1 ABSOLUTE RATINGS OF ENVIRONMENT

Item Symbol

Storage Temperature TST -20 60 ºC (1)

Operating Ambient T emperature TOP 0 50 ºC (1), (2)

Shock (Non-Operating) S

Vibration (Non-Operating) V

Note (1) Temperature and relative humidity range is shown in the figure below. (a) 90 %RH Max. (Ta ≦ 40 ºC). (b) Wet-bulb temperature should be 39 ºC Max. (Ta > 40 ºC). (c) No condensation. Note (2) The temperature of panel display surface area should be 0 ºC Min. and 60 ºC Max.

- 50 G (3), (5)

NOP

- 1.5 G (4), (5)

NOP

Min. Max.

Value

Unit Note

Note (3) 50G,11ms, half sine wave, 1 time for ± X, ± Y, ± Z. Note (4) 10 ~ 300 Hz, 10min/cycle, 3 cycles each X, Y, Z. Note (5) At testing Vibration and Shock, the fixture in holding the module has to be hard and rigid enough

Relative Humidity (%RH)

100

90

80

60

Operating Range

40

www.jxlcd.com

20

10

Storage Range

80 60 -20 40 0 20 -40

Temperature (oC)

so that the module would not be twisted or bent by the fixture.

The fixing condition is shown as below:

t Room Temperature

Side Mount Fixing Screw

Gap=3~5mm

Bracket

5 / 26

LCD Module

Side Mount Fixing Screw

Stage

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

2.2 ELECTRICAL ABSOLUTE RATINGS

2.2.1 TFT LCD MODULE

Item Symbol

Power Supply Voltage Vcc -0.3 +6.0 V (1)

2.2.2 BACKLIGHT UNIT

Item Symbol

Lamp Voltage VL - 2.5K V Lamp Current IL 2.0 8.0 mA

Lamp Frequency FL 40 80 KHz

Note (1) Permanent damage to the device may occur if maximum values are exceeded. Function operation

should be restricted to the conditions described under Normal Operating Co nditions.

Note (2) Specified values are for lamp (Refer to 3.2 for further information).

Min. Max.

Value

Unit Note

(1), (2), IL = 7.5mA

RMS

(1), (2)

www.jxlcd.com

6 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

3. ELECTRICAL CHARACTERISTICS

3.1.1 TFT LCD MODULE Ta = 25 ± 2 ºC

Parameter Symbol

Min. Typ. Max.

Power Supply V oltage Vcc 4.5 5.0 5.5 V -

Ripple Voltage VRP - - 100 mV -

Rush Current I

RUSH

- - 3 A (2)

White - 0.44 0.6 A (3)a

Power Supply Current

Black - 0.58 0.9 A (3)b

Vertical Stripe

lcc

- 0.6 0.9 A (3)c

Power Consumption - 3.0 4.5 Watt (4)

LVDS differential input voltage Vid 100 - 600 mV -

LVDS common input voltage Vic - 1.2 - V -

Note (1) The module should be always operated within above ranges. Note (2) Measurement Conditions:

Value

Unit Note

+5.0V

R1

47K

Q1 2SK1475

FUSE

C3 1uF

Vcc

(LCD Module Input)

(High to Low)

(Control Signal)

SW

www.jxlcd.com

+12V

www.jxlcd.com

C1

1uF

VR1

R2

1K

47K

0.01uF

Q2

2SK1470

C2

Vcc rising time is 470µs

Vcc

0.9Vcc

0.1Vcc

GND

470µs

7 / 26

Version 2.0

Doc No.: 400029638

≤≤≤

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

Note (3) The specified power supply current is under the conditions at Vcc = 5.0 V, Ta = 25 ± 2 ºC, f

Hz, whereas a power dissipation check pattern below is displayed. a. White Pattern

Active Area

c. Vertical Stripe Pattern

www.jxlcd.com

Active Area

b. Black Pattern

Active Area

R

G

R

B

G

R

B

G

R R

G

B B

R R

R

G G

B B

R

= 60

v

Note (4) The power consumption is specified at the pattern with the maximum current.

3.1.2 Vcc Power Dip Condition:

Dip condition:

Td

Vcc

4.5V

4.0V

msTdVVccV 20,5.40.4

8 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

3.2 BACKLIGHT UNIT Ta = 25 ± 2 ºC

Parameter Symbol

Lamp Input Voltage VL --- 760 836 V

Lamp Current IL 2.0 7.5 8.0 mA

Lamp Turn On Voltage VS

Operating Frequency FL 40 --- 80 KHz (3)

Lamp Life Time LBL 40000 --- --- Hrs (5), IL = 7.5mA

Power Consumption PL --- 10.85 --- W (4), IL = 7.5 mA

Note (1) Lamp current is measured by current amplify & oscilloscope as shown below:

Min. Typ. Max.

--- ---

Value

1680(0℃)

1460(25℃)

Unit Note

I

RMS

V

(2)

RMS

V

(2)

RMS

= 7.5 mA

L

(1)

Note (2) The voltage that must be larger than Vs should be applied to the lamp for more than 1 second

Note (3) The lamp frequency may produce interference with horizontal synchronization frequency from the

LCD Module

www.jxlcd.com

after startup. Otherwise, the lamp may not be turned on normally. It is the value output voltage of NF circuit.

HV+ (Pink)

LV (White)

HV- (Pin k)

LV (White)

Current Probe

1 2

A

Inverter

Current Amplify

1 2

A

Measure equipment: Current Amplify: Tektronix TCPA300 Current probe: Tektronix TCP312 Oscilloscope: TDS3054B

Oscilloscope

display, which might cause line flow on the display. In order to avoid interference, the lamp frequency should be detached from the horizontal synchronization frequency and its harmonics as

far as possible. Note (4) P Note (5) The lifetime of lamp can be defined as the time in which it continues to operate under the condition

(The effective ignition length is a scope that luminance is over 80% of that at the center point.)

Note (6) The waveform of the voltage output of inverter must be area-symmetric and the design of the

= IL × VL × 2 (for 2 lamps)

L

Ta = 25 ±2

(a) When the brightness becomes ≦ 50% of its original value. (b) When the effective ignition length becomes 80% of its original value.≦

inverter must have specifications for the modularized lamp. The performance of the Backlight,

o

C and( IL = 7.5 mArms )until one of the following events occurs:

9 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

such as lifetime or brightness, is greatly influenced by the characteristics of the DC-AC inverter for

the lamp. All the parameters of an inverter should be carefully designed to avoid producing too

much current leakage from high voltage output of the inverter. When designing or ordering the

inverter please make sure that a poor lighting caused by the mismatch of the Backlight and the

inverter (miss-lighting, flicker, etc.) never occurs. If the above situation is confirmed, the module

should be operated in the same manners when it is installed in your instrume nt.

The output of the inverter must have symmetrical (negative and positive) voltage waveform and symmetrical current waveform.(Unsymmetrical ratio is less than 10%) Please do not use the inverter which has unsymmetrical voltage and unsymmetrical current and spike wave. Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may cause beat on the display. Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference.

Requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp. It shall help increase the lamp lifetime and reduce its leakage current. a. The asymmetry rate of the inverter waveform should be 10% below; b. The distortion rate of the waveform should be within √2 ± 10%;

c. The ideal sine wave form shall be symmetric in positive and negative polarities

www.jxlcd.com

* Asymmetry rate:

I p

I -p

| I

* Distortion rate I

– I –p | / I

p

(or I –p) / I

p

rms

* 100%

10 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

4. BLOCK DIAGRAM

4.1 TFT LCD MODULE

RX0(+/-) RX1(+/-) RX2(+/-) RX3(+/-) RXC(+/-) NC

GND Vcc

(STM MSAKT2407P30A

or EQUIVALENT)

INPUT CONNECTOR

LVDS INPUT /

TIMING CONTROLLER

DC/DC CONVERTER &

REFERENCE VOLTAGE

SCAN DRIVER IC

TFT LCD PANEL

(1366x3x768)

DA TA DRIVER IC

VL

LAMP CONNECTOR

(YEONHO 35001HS-02L)

4.2 BACKLIGHT UNIT

www.jxlcd.com

BACKLIGHT UNIT

1 HV(Pink)

2 LV(White)

1 HV(Pink)

2 LV(White)

11 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

5. INPUT TERMINAL PIN ASSIGNMENT

5.1 TFT LCD MODULE

Pin Name Description

1 NC Not connection, this pin should be open. 2 NC Not connection, this pin should be open. 3 NC Not connection, this pin should be open. 4 GND Ground 5 RX0- Negative LVDS differential data input. Channel 0 6 RX0+ Positive LVDS differential data input. Channel 0 7 GND Ground 8 RX1- Negative LVDS differential data input. Channel 1

9 RX1+ Positive LVDS differential data input. Channel 1 10 GND Ground 11 RX2- Negative LVDS differential data input. Channel 2 12 RX2+ Positive LVDS differential data input. Channel 2 13 GND Ground 14 RXCLK- Negative LVDS differential clock input. 15 RXCLK+ Positive LVDS differential clock input. 16 GND Ground 17 RX3- Negative LVDS differential data input. Channel 3 18 RX3+ Positive LVDS differential data input. Channel 3 19 GND Ground 20 NC Not connection, this pin should be open. 21 NC Not connection, this pin should be open. 22 NC Not connection, this pin should be open. 23 GND Ground 24 GND Ground 25 GND Ground 26 Vcc +5.0V power supply 27 Vcc +5.0V power supply 28 Vcc +5.0V power supply 29 Vcc +5.0V power supply 30 Vcc +5.0V power supply

Note (1) Connector Part No.: STM MSAKT2407P30A or equivalent

www.jxlcd.com

12 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

5.2 LVDS mapping table

LVDS Channel 0

LVDS Channel 1

LVDS Channel 2

LVDS Channel 3

5.3 BACKLIGHT UNIT:

Pin Symbol Description Remark

1 HV High Voltage Pink 2 LV Low Voltage White

Note (1) Connector Part No.: YEONHO 35001HS-02L or equivalent

LVDS output D7 D6 D4 D3 D2 D1 D0 Data order G0 R5 R4 R3 R2 R1 R0 LVDS output D18 D15 D14 D13 D12 D9 D8 Data order B1 B0 G5 G4 G3 G2 G1 LVDS output D26 D25 D24 D22 D21 D20 D19 Data order DE NA NA B5 B4 B3 B2 LVDS output D23 D17 D16 D11 D10 D5 D27 Data order NA B7 B6 G7 G6 R7 R6

www.jxlcd.com

13 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

5.4 COLOR DATA INPUT ASSIGNMENT

The brightness of each primary color (red, green and blue) is based on the 8-bit gray scale data input for the color. The higher the binary input, the brighter the color. The table below provides the assignment of color versus data input.

Data Signal

Basic

Colors

Gray

Scale

Of

Red

Color

Black

Red

Green

Blue

Cyan

Magenta

Yellow

White

Red(0) / Dark

Red(1) Red(2)

Red(253) Red(254) Red(255)

R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0

0

1

0

1

0

:

1

Red Green Blue

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

1

0

:

1

0

1

0

1

0

1

0

0 0 0 1 1 1 0 1 0 0 0

0 0 0

0

1

0

1

0

:

0

Green(0) / Dark

Gray

Scale

Of

Green

Gray

Scale

Of

Blue

Note (1) 0: Low Level Volt age, 1: High Level Voltage

Green(1) Green(2)

www.jxlcd.com

Green(253)

www.jxlcd.com

Green(254) Green(255)

Blue(0) / Dark

Blue(1) Blue(2)

Blue(253) Blue(254) Blue(255)

0

:

0

:

0

1

0

1

0

:

0

1

0

1

0

1

0

1

0

1

0

1

0

:

0

1

0

1

0

1

0

1

14 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

6. INTERFACE TIMING

6.1 INPUT SIGNAL TIMING SPECIFICATIONS

The input signal timing specifications are shown as the following table and timing diagram.

Signal Item Symbol Min. Typ. Max. Unit Note

Frequency Fc 50.0 76 95 MHz -

LVDS Clock

LVDS Data

Vertical Active Display Term

Horizontal Active Display Term

Note: Because this module is operated by DE only mode, Hsync and Vsync input signals should be set

Period Tc 10.5 13.2 20 ns High Time T ch - 4/7 - Tc Low Time Tcl - 3/7 - Tc Setup Time Tlvs 600 - - ps Hold Time Tlvh 600 - - ps Frame Rate Fr 50 60 75 Hz Tv=Tvd+Tvb Total Tv 778 806 888 Th Display Tvd 768 768 768 Th Blank Tvb Tv-Tvd 38 Tv-Tvd Th Total Th 1446 1560 1936 Tc Th=Thd+Thb Display Thd 1366 1366 1366 Tc Blank Thb Th-Thd 194 Th-Thd Tc -

to low logic level or ground. Otherwise, this module would operate abnormally.

INPUT SIGNAL TIMING DIAGRAM

www.jxlcd.com

DE

Th

DCLK

C

T

DE

DATA

Thb

T

hd

15 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

6.2 POWER ON/OFF SEQUENCE To prevent a latch-up or DC operation of LCD module, the power on/off sequence should be as the diagram below.

Power Supply

for LCD, Vcc

-

Interface Signal (LVDS Signal of Transmitter), V

-

Power for Lamp

Timing Specifications:

0.5< t1 ≦ 5 msec 0 < t2 ≦ 50 msec 0 < t3 ≦ 50 msec

t7

10%

Restart

10%

t4

Power On

90%

0V

I

www.jxlcd.com

t4 ≧ 500 msec

10%

t1

t2

Valid Data

ONOFF OFF

Power Off

90%

t3

t6 t5

50%50%

t5 ≧ 450 msec t6 ≧ 90 msec

5 ≦t7 ≦ 100 msec

Note.

(1) The supply voltage of the external system for the module input should be the same as the definition of Vcc. (2) Apply the lamp voltage within the LCD operation range. When the backlight turns on before the LCD

operation of the LCD turns off, the display may momentarily become abnormal screen.

(3) In case of VCC = off level, please keep the level of input signals on the low or keep a high i mpedance. (4) T4 should be measured after the module has been fully discharged between power off and on period. (5) Interface signal shall not be kept at high impedance when the power is on. (6)

The company will not guarantee or compensate for the product damage caused by not following the Power

Sequence.

16 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

7. OPTICAL CHARACTERISTICS

7.1 TEST CONDITIONS

Item Symbol Value Unit

Ambient Temperature Ta 25±2

Ambient Humidity Ha 50±10 %RH

Supply Volt age VCC 5V V

Input Signal According to typical value in "3. ELECTRICAL CHARACTERISTICS"

Lamp Current IL 7.5 ± 0.5 mA

Inverter Operating Frequency FL 55±5 KHz

Inverter

Logah MIT70070.50

7.2 OPTICAL SPECIFICATIONS

The relative measurement methods of optical characteristics are shown in 7.2. The following items should

be measured under the test conditions described in 7.1 and stable environment shown in Note (5).

o

C

Item Symbol Condition Min. Typ. Max. Unit Note

Red

Color

Chromaticity

(CIE 1931)

Center Luminance of White

Viewing Angle

www.jxlcd.com

(Center of Screen)

Contrast Ratio CR

Response Time

White Variation δW

Green

Blue

White

Horizontal

Vertical

Horizontal

Vertical

Rx Ry Gx Gy

Bx

By Wx Wy

L

C

TR - 1.3 3.2

T

F

θx+

θ

-

x

θY+ θ

-

Y

θx+

θ

-

x

θY+ θ

-

Y

=0°, θY =0°

θ

x

CS-1000T

=0°, θY =0°

θ

x

θ

=0°, θY =0°

x

USB2000

CR ≧ 10

USB2000

CR>5

Typ -

0.03

185 250 - cd/m2(4), (5) 700 1000 - - (2), (5)

75 75 70

70 80

80 75

75

0.646

0.334

0.284

0.602

0.152

0.076

0.313

0.329

- 3.7 6.8

- 1.3 1.42 - (5), (6) 85 -

85 80 80 89 --89 85 85

Typ +

0.03

-

---

- (1), (5)

ms (3)

Deg. (1), (5)

17 / 26

Version 2.0

Doc No.: 400029638

y

−

+

y

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

Note (1) Definition of Viewing Angle (θx, θy):

Normal

θX- = 90º

6 o’clock

- = 90º

θ

Note (2) Definition of Contrast Ratio (CR):

The contrast ratio can be calculated by the following expression.

Contrast Ratio (CR) = L255 / L0 L255: Luminance of gray level 255

www.jxlcd.com

L 0: Luminance of gray level 0

x-

y-

θx = θ

θy- θy+

= 0º

θx

12 o’clock direction

y+

+ = 90º

θ

x+

θX+ = 90º

CR = CR (5)

CR (X) is corresponding to the Contrast Ratio of the point X at Figure in Note (6).

Note (3) Definition of Response Time (T

100%

90%

Optical

Response

10%

0%

Gray Level 255

, TF):

R

Gray Level 255

Gray Level 0

T

R

66.67ms 66.67ms

F

18 / 26

Version 2.0

Doc No.: 400029638

500

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

Note (4) Definition of Luminance of White (LC):

Measure the luminance of gray level 255 at center point

LC = L (5)

L (x) is corresponding to the luminance of the point X at Figure in Note (6).

Note (5) Measurement Setup:

The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt temperature change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting Backlight for 20 minutes in a windless room.

www.jxlcd.com

LCD Module

LCD Panel

USB2000

Center of the Screen

CS-1000T

Light Shield Room

mm

(Ambient Luminance < 2 lux)

Note (6) Definition of White Variation (δW):

Measure the luminance of gray level 255 at 9 points δW = Maximum [L (1), L (2) ……L (4), L (9)] / Minimum [L (1), L (2) …… L (4), L (9)]

D/10

Horizontal Line

D

D/2

9D/10

W/10

Vertical Line

W

W/2

9W/10

1

4

7 8 9

2

5

Active Area

3

X

6

: Test Point X=1 to 9

19 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

8. PACKAGING：

8.1 PACKING SPECIFICATIONS

(1) 9 LCD modules / 1 Box (2) Box dimensions: 525(L) X 300 (W) X 360 (H) mm (3) Weight: 19.79 Kg (9 modules per box) (4) Desiccant ( Drier ) : Weight 30g / 1 piece, Cobalt chloride free.

8.2 PACKING METHOD

(1) Carton Packing should have no failure in the following reliability test items.

Test Item Test Conditions Note

ISTA STANDARD Random, Frequency Range: 1 – 200 Hz

Vibration

Dropping Test 1 Corner, 3 Edge, 6 Face, ISTA STANDARD Non Operation

Top & Bottom: 30 minutes (+Z), 10 min (-Z), Right & Left: 10 minutes (X) Back & Forth 10 minutes (Y)

Non Operation

www.jxlcd.com

Figure. 8-1 Packing method

20 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

For ocean shipping

Sea / Land Transportation (40ft HQ Container)

PP Belt

Carton label

Film

PE Sheet

Corner Protector (50*50*1000mm)

Pallet (1150*1150*143mm)

Sea / Land Transportation (40ft Container)

PP Belt

Carton label

Film

PE Sheet

Corner Protector (50*50*1000mm)

Figure. 8-2 Packing method

Corner Protector (50*50*625mm)

Corner Protector (50*50*1000mm)

Pallet (1150*1150*143mm)

For air transport

Corner Protector (50*50*1000mm)

PE Sheet

Film

www.jxlcd.com

Air Transportation

PP Belt

Corner Protector (50*50*1000mm)

Pallet (1150*1150*143mm)

Carton label

Figure. 8-3 Packing method

21 / 26

Version 2.0

Doc No.: 400029638

,

y

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

9. DEFINITION OF LABELS

9.1 CMO MODULE LABEL

The barcode nameplate is pasted on each module as illustration, and its definitions are as following explanation.

(a) Model Name: M185B1-L05 (b) Revision: Rev. XX, for example: A0, A1… B1, B2… or C1, C2…etc. (c) CMO barcode definition:

Serial ID: XX

Code Meaning Description

XX CMO internal use XX Revision Cover all the change

X CMO internal use -

XX CMO internal use -

YMD Year, month, day

L Product line # Line 1=1, Line 2=2, Line 3=3, …

NNNN Serial number Manufacturing sequence of product

www.jxlcd.com

(d) Customer’s barcode definition:

www.jxlcd.com

Serial ID: CM

Code Meaning Description

CM Supplier code CMO=CM

18B15 Model number M185B1-L05 = 18B15

X Revision code Non ZBD: 1,2,~,8,9 / ZBD: A~Z X X Gate driver IC code

XX Cell location Tainan Taiwan=TN, Ningbo China=NP

L Cell line #

XX Module location Tainan Taiwan=TN ; Ningbo China=NP

L Module line #

YMD Year, month, day

NNNN Serial number By LCD supplier

-XX-X-XX-YMD-L-NNNN

Year: 2001=1, 2002=2, 2003=3, 2004=4… Month: 1~12=1, 2, 3, ~, 9, A, B, C Day: 1~31=1, 2, 3, ~, 9, A, B, C, ~, W, X, Y, exclude I, O, and U.

-18B15-X-X-X-XX-L-XX-L-YMD-NNNN

Source driver IC

Century=1, CLL=2, Demos=3, Epson=4, Fujitsu=5, Himax=6, Hitachi=7, Hynix=8, LDI=9, Matsushita=A, NEC=B, Novatec=C, OKI=D, Philips=E, Renasas=F

1,2,~,9,A,B,~,Y,Z

Year: 2001=1, 2002=2, 2003=3, 2004=4… Month: 1~12=1, 2, 3, ~, 9, A, B, C Da

Samsung=G, Sanyo=H, Sharp=I, TI=J, Topro=K, Toshiba=L,

: 1~31=1, 2, 3, ~, 9, A, B, C, ~, T, U, V

(e) UL Factory ID:

Region Factory ID TWCMO GEMN NBCMO LEOO

NBCME CANO

NHCMO CAPG

22 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

10. PRECAUTIONS

10.1 ASSEMBL Y AND HANDLING PRECAUTIONS

(1) Do not apply rough force such as bending or twisting to the module during assembly. (2) To assemble or install module into user’s system can be only in clean working areas. The dust and oil

may cause electrical short or worsen the polarizer.

(3) It’s not permitted to have pressure or impulse on the module because the LCD panel and Backlight will

be damaged.

(4) Always follow the correct power sequence when LCD module is connecting and operating. This can

prevent damage to the CMOS LSI chips during latch-up. (5) Do not pull the I/F connector in or out while the module is operating. (6) Do not disassemble the module. (7) Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and

easily scratched. (8) It is dangerous that moisture come into or contacted the LCD module, because moisture may damage

LCD module when it is operating. (9) High temperature or humidity may reduce the performance of module. Please store LCD module within

the specified storage conditions. (10) When ambient temperature is lower than 10ºC may reduce the display quality. For example, the

response time will become slowly, and the starting voltage of CCFL will be higher than room

temperature.

www.jxlcd.com

10.2 SAFETY PRECAUTIONS

(1) The startup voltage of Backlight is approximately 1000 Volts. It may cause electrical shock while

assembling with inverter. Do not disa ssemble the module or insert anything into the Backlight unit. (2) If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In

case of contact with hands, skin or clothes, it has to be washe d away thoroughly with soap. (3) After the module’s end of life, it is not harmful in case of normal operation and storage.

10.3 SAFETY STANDARDS

www.jxlcd.com

The LCD module should be certified with safety regulations as follows: (1) UL60950-1 or updated standard. (2) IEC60950-1 or updated standard.

10.4 OTHER

When fixed patterns are displayed for a long time, remnant image is likely to occur.

23 / 26

Version 2.0

Doc No.: 400029638

Issued Date: Feb. 09, 2009

Model No.: M185B1-L05

Approval

11. MECHANICAL CHARACTERISTICS

[Refer to the next 2 pages]

www.jxlcd.com

24 / 26

Version 2.0

www.jxlcd.com

Datasheet M185B1-L05 Datasheet (Chi Mei Optoelectronics)

Specifications and Main Features

Frequently Asked Questions

User Manual