Page 1
www.jxlcd.com
www.jxlcd.com
Page 2
2
Issued Date: Apr.28 2005
Model No.: M170E5-C03
Approval
- CONTENTS -
.
REVISION HISTORY ------------------------------------------------------- 3
1. GENERAL DESCRIPTION ------------------------------------------------------- 4
1.1 OVERVIEW
1.2 FEATURES
1.3 APPLICATION
1.4 GENERAL SPECIFICATIONS
2. ABSOLUTE MAXIMUM RATINGS ---------------------------------------------- 4
3. SUGGESTIVE DRIVING CONDITION ---------------------------------------------- 5
4. PANEL PIN DEFINITION ------------------------------------------------------- 6
5. OPTICAL CHARACTERISTICS ---------------------------------------------- 7
5.1 TEST CONDITIONS
5.2 OPTICAL SPECIFICATIONS
6. PACKAGING --------------------------------------------- 11
6.1 PACKING SPECIFICATIONS
6.2 PACKING METHOD
7. DEFINITION OF LABELS ---------------------------------------------- 12
8. PRECAUTIONS ---------------------------------------------- 13
8.1 ASSEMBLY AND HANDLING PRECAUTIONS
8.2 SAFETY PRECAUTIONS
9. PANEL DRAWING ---------------------------------------------- 14
www.jxlcd.com
www.jxlcd.com
/14
2
Version 2.0
Page 3
REVISION HISTORY
Version Date Section Description
3
Issued Date: Apr.28 2005
Model No.: M170E5-C03
Approval
Ver 1.0
Ver 2.0
Mar, 01 ’05
Apr, 28 ‘05
-
1.4
5.2
9
M170E5-C03 Specifications was first issued。
Add “Weight” item , Weight=400g(typ.)
Delete R,G,B,W color coordinate which uses CMO’s BLU
Center point Transmittance : typ. from 5.25%to 5.3%
Add “PANEL DRAWING”
www.jxlcd.com
www.jxlcd.com
/14
3
Version 2.0
Page 4
4
Issued Date: Apr.28 2005
Model No.: M170E5-C03
Approval
1.GENERAL DESCRIPTION
1.1 OVERVIEW
The M170E5-C03 is a 17-inch LCD cell with thin film transistors as active elements and contains
1280x1024 pixels. Each pixel is divided into red, green and blue dot, which are arranged in vertical stripe.
The cell is normally white mode, and can be applied to the transmission type display. Backlight unit (BLU)
and circuit board for the cell are not built in.
1.2 FEATURES
- Wide viewing angle
- High contrast ratio
- Fast response time
- SXGA (1280 x 1024 pixels) resolution
1.3 APPLICATION
- LCD Monitor
- LCD TV
1.4 GENERAL SPECIFICATIONS
Item Specification Unit
Max Panel Dimension (TFT) 348.3 X 280.9 mm
Glass thickness( TFT/ CF ) 0.7/ 0.7 mm
Active Area 337.92 (H) x 270.34 (V) (17.0” diagonal) mm
Driver Element a-si TFT active matrix Pixel Number 1280X R.G.B X 1024 pixel
Pixel Pitch 0.264 (H) X 0.264 (V) mm
Pixel Arrangement RGB vertical stripe Transmissive Mode Normally white Surface Treatment Hard coating (3H), AG (Haze 25%) Polarizer Type Super Wide View -
Polarizer Dimension
Polarizer Thickness
2. ABSOLUTE MAXIMUM RATINGS
1. Storage condition : With shipping package.
www.jxlcd.com
www.jxlcd.com
TFT 344.1 X 276.5 mm
CF 340.6 X 273.0 mm
TFT 0.245 mm
CF 0.245 mm
Weight 400(typ.) g
2. Storage temperature range : 25±5 ℃.
3. Storage humidity range : 50±10% RH.
4. Shelf life : 30 days
Version 2.0
/14
4
Page 5
3. Suggestive Driving Condition
Item Min. Typ. Max. Unit
VG
Driving
Voltage
B: Black pattern
W: White pattern
Gamma Voltage : Gam1 > Gam2 > Gam3 > … > Gam10
G↓: gate pulse falling edge
VD
V
G↓-D offset
Charging time - 9.8 - us
On 22.3 23 23.7 V
Off -7.1 -6.8 -6.6 V
Gam1 - 9.73 - V
B
Gam10 - 0.14 - V
Gam5 - 5.56 - V
W
Gam6 - 4.99 - V
Center 3.7 3.9 4.1 V
COM
5
Issued Date: Apr.28 2005
Model No.: M170E5-C03
Approval
2.0 - - us
DRIVING TIMING DIAGRAM
www.jxlcd.com
www.jxlcd.com
VCOM
VD
VG
/14
5
Version 2.0
Page 6
4. PANEL PIN DEFINITION
6
Issued Date: Apr.28 2005
Model No.: M170E5-C03
Approval
Pin No.
TAB1 TAB2 ~ 9 TAB10
1~2 NC NC NC
Data driver Pin Define
3 floating is recommend NC NC
4 floating is recommend NC NC
5 XAO NC NC
6 OE NC NC
7 CPV NC NC
8 STV NC NC
9~11 Vss NC NC
12~14 Vdd NC NC
15~16 Vee NC NC
17~18 floating is recommend NC NC
19 NC NC NC
20~21 floating is recommend NC NC
22 NC NC NC
23~26 Vgl NC NC
27 NC NC NC
28~31 Vgh NC NC
32 NC NC NC
www.jxlcd.com
33~34 Vcom Vcom Vcom
35 Vcom Vcom Vcom
36 floating is recommend floating is recommend floating is recommend
37 out1 out1 out1
38 ~ 419 out2 ~ 383 out2 ~383 out2 ~383
420 out384 out384 out384
421 floating is recommend floating is recommend floating is recommend
422 NC NC floating is recommend
423 NC NC NC
424~425 NC NC Vcom
426~427 NC NC Vgl
428 NC NC NC
429 NC NC floating is recommend
430 NC NC NC
431~434 Vcom Vcom Vcom
435~436 NC NC NC
www.jxlcd.com
Note: Recommended Gate IC for the cell is HiMAX’s HX8607APD400, 256/263Ch, or equivalent.
/14
6
Version 2.0
Page 7
Issued Date: Apr.28 2005
Model No.: M170E5-C03
5. OPTICAL CHARACTERISTICS
5.1 TEST CONDITIONS
Item Symbol Value Unit
Ambient Temperature Ta
Ambient Humidity Ha
Gamma voltage - Refer to Item 3 driving condition V
Vcom - most suitable Vcom V
25±2
50±10
5.2 OPTICAL SPECIFICATION
ITEM Symbol Condition MIN. TYP. MAX. UNIT NOTE
Contrast Ratio CR θx=θy=0∘ 400 500 - % 4,1
Tr θx=θy=0∘ - 2 7 ms Response Time
(Black/White)
Center point Transmittance T% θx=θy=0∘ 4.8 5.3 - % 7,1
Tf θx=θy=0∘ - 6 11 ms
Approval
o
C
%RH
5,1
7
Transmittance uniformity
(13pts)
Viewing
Angle
Color
Coordinate
at center
point
(θy=0∘)
Vertical θy
(θx=0∘)
Red
Green
www.jxlcd.com
www.jxlcd.com
Blue
White
δT%
Right 65 75 - Deg Horizontal θx
Left 65 75 - Deg
Up 60 70 - Deg
Down
Rcx θx=θy=0∘ 0.650 Rcy θx=θy=0∘ 0.343 Gcx θx=θy=0∘ 0.274 Gcy θx=θy=0∘ 0.600 Bcx θx=θy=0∘ 0.132 -
Bcy θx=θy=0∘ 0.112 Wcx θx=θy=0∘ 0.318 Wcy θx=θy=0∘
θx=θy=0∘ - 1.25 1.4 - 6,1
CR≧10
Note (0)
Light source is the standard light source “C” which is defined by CIE and driving voltages are based on
suitable gamma voltages. The calculating method is as following：
1.Measure Module’s and BLU’s spectrums. White is without signal input and R, G, B are with signal input.
BLU is supplied by CMO.
2.Calculate cell’s spectrum.
50 60 - Deg
Typ
-0.03
0.361
Typ
+0.03
-
2,3,1
2,0
3.Calculate cell’s chromaticity by using the spectrum of standard light source “C”
/14
7
Version 2.0
Page 8
Issued Date: Apr.28 2005
Model No.: M170E5-C03
Approval
Note (1)
Light source is the BLU which is supplied by CMO and driving voltages are based on suitable gamma
voltages. White is without signal input and R, G, B are with signal input. SPEC is judged by CMO’s golden sample .
Note (2) : Measurement setup:
The LCD module should be stabilized at given temperature for 20 minutes to avoid abrupt temperature
change during measuring. In order to stabilize the luminance, the measurement should be executed after lighting
backlight for 20 minutes in a windless room.
8
LCD Module
LCD Panel
Photometer
Center of the Screen
Field of View = 2º
www.jxlcd.com
www.jxlcd.com
500 mm
(TOPCON BM-5A or CS-1000T)
Light Shield Room
(Ambient Luminance < 2
/14
8
Version 2.0
Page 9
Note (3) : Definition of viewing angle (θx ,θy):
9
Issued Date: Apr.28 2005
Model No.: M170E5-C03
Approval
Note (4) : Definition of Contrast Ratio (CR):
Ratio of gray max (Gmax), gray min (Gmin), at the center point of panel.
CR =
Note (5) : Definition of Response Time (T
www.jxlcd.com
Optical
Response
Luminance with all pixel white (Gmax)
www.jxlcd.com
Luminance with all pixel Black (Gmin)
100%
90%
10%
0%
R, TF):
Version 2.0
T
R T
/14
9
F
Time
Page 10
Note (6) : Definition of Transmittance Variation (δT%):
Measure the transmittance at 13 points
δT% =
Maximum [T%(1), T%(2), … T%(13)]
Minimum [T%(1), T%(2), … T%(13)]
10
Issued Date: Apr.28 2005
Model No.: M170E5-C03
Approval
Note (7) : Definition of Transmittance(T%):
Module is without signal input.
BLU is Supplied by CMO .
Vertical Line
www.jxlcd.com
W/10
W/4
W/2
W
3W/4
9W/10
www.jxlcd.com
D/10
6
9
11 12 13
D
D/4 D/2 3D/4
7
2 3
1
4
Active Area
5
9D/10
8
10
X
: Test Point
X=1 to 13
Transmittance
Luminance of LCD module
=
Luminance of backlight
＊ 100%
/14
10
Version 2.0
Page 11
6. PACKAGING
6.1.PACKING SPECIFICATION
1. 15 pcs LCD panel / 1 Box
2. Box Dimension : 391(L) X 333(W) X 474(H) mm
3. Weight : Approximately 7Kg (15 panel per box)
6.2 PACKING METHOD
11
Issued Date: Apr.28 2005
Model No.: M170E5-C03
Approval
www.jxlcd.com
www.jxlcd.com
Figure. 6-1 Packing method
Box dimensions : 391(L) X 333(W) X 474(H) mm
Weight : approximately 7Kg (15 panel per box)
/14
11
Version 2.0
Page 12
12
Issued Date: Apr.28 2005
Model No.: M170E5-C03
Approval
Figure. 6-2 Packing method
www.jxlcd.com
7. DEFINITION OF LABEL
1. Mode Name: M170E5- C03
2. Panel Type: version control
3. Quantity: 15pcs / PP box
4. Case ID: serial number.
5. Note: Notification, if necessary.
6. Barcode: Case ID in code39 format
www.jxlcd.com
12
Version 2.0
Figure. 7-1 Packing Label
/14
Page 13
Issued Date: Apr.28 2005
Model No.: M170E5-C03
Approval
8. PRECAUTIONS
8.1 ASSEMBLY AND HANDLING PRECAUTIONS
1. Do not apply rough force such as bending or twisting to the cell during assembly.
2. To assemble or install cell into customer’s module can be only in clean working areas. The dust and
oil may cause electrical short or worsen the polarizer.
3. It’s not permitted to have pressure or impulse on the module because the LCD panel and Backlight
will be damaged.
4. Use a soft dry cloth without chemicals for cleaning, because the surface of polarizer is very soft and
easily scratched.
5. It is dangerous that moisture come into or contacted the LCD panel, because moisture may damage
TFT circuit .
6. High temperature or humidity may reduce the performance of cell. Please store LCD cell within the
13
specified storage conditions.
8.2 SAFETY PRECAUTIONS
1. If the liquid crystal material leaks from the panel, it should be kept away from the eyes or mouth. In
case of contact with hands, skin or clothes, it has to be washed away thoroughly with soap.
www.jxlcd.com
www.jxlcd.com
/14
13
Version 2.0
Page 14
www.jxlcd.com
www.jxlcd.com
Loading...