Datasheet LTC2050 Datasheet (Linear Technology)

LTC2050

Final Electrical Specifications

Zero-Drift

Operational Amplifier

in SOT-23

November 1999

EATU

F

■

SOT-23 Package

■

Maximum Offset Voltage of 3µV

■

Maximum Offset Voltage Drift of 30nV/°C

■

Noise: 1.5µV

■

Voltage Gain: 140dB (Typ)

■

PSRR: 130dB (Typ)

■

CMRR: 130dB (Typ)

■

Supply Current: 0.8mA (Typ)

■

Single Supply Operation: 2.7V to 6V

■

Extended Common Mode Input Range

■

Output Swings Rail-to-Rail

■

Overload Recovery Time: 2ms (Typ)

PPLICATI

A

■

Thermocouple Amplifiers

■

Electronic Scales

■

Medical Instrumentation

■

Strain Gauge Amplifiers

■

High Resolution Data Acquisition

■

DC Accurate RC Active Filters

RE

S

(0.1Hz to 10Hz Typ)

P-P

U

O

S

DUESCRIPTIO

The LTC®2050 is a low drift operational amplifier available
in the 5- or 6-lead SOT-23 and SO-8 packages. It operates
from a single 2.7V supply while still supporting 5V appli­cations. The power consumption is 800µA and the ver-
sions in the 6-lead SOT-23 and SO-8 packages offer power
shutdown (active low).

The LTC2050, despite its miniature size, features uncom­promising DC performance. The typical input offset volt­age and offset drift are 0.5µV and 10nV/°C. The almost
zero DC offset and drift are supported with a power supply
rejection ratio (PSRR) and common mode rejection ratio
(CMRR) of more than 130dB.

The input common mode voltage ranges from the negative
supply up to 1V from the positive supply. The LTC2050
also has an enhanced output stage capable of driving
loads as low as 1kΩ to both supply rails. The open-loop
gain, loaded with 1kΩ, is in excess of 140dB. The LTC2050
also features a 1.5µV
bandwidth product.

, LTC and LT are registered trademarks of Linear Technology Corporation.

DC to 10Hz noise and a 3MHz gain

P-P

A

PPLICATITYPICAL

5V

50Ω
GAIN
TRIM

350Ω

STRAIN

GAUGE

U

O

Differential Bridge Amplifier

5V

0.1µF

2

–

3

+

1000pF

18.2k

Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen­tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.

1000pF

18.2k

7

LTC2050

4

2050 TA01

Input Referred Noise 0.1Hz to 10Hz

VS = 5V

3

1

0

µV

6

A

= 100

V

–1

–3

2

0

4

TIME (s)

6

8

10

LT2050 TA02

1

LTC2050

A

W

O

LUTEXI TIS

S

A

WUW

U

ARB

G

(Note 1)

Total Supply Voltage (V+ to V–) ............................... 7V

Input Voltage ........................ (V+ + 0.3V) to (V– – 0.3V)

Output Short-Circuit Duration......................... Indefinite

Operating Temperature Range ............... –40°C to 85°C

WU

/

PACKAGE

OUT 1

V

+IN 3

ORDER PART

NUMBER

O

RDER I FOR ATIO

TOP VIEW

–

2

S5 PACKAGE

5-LEAD PLASTIC SOT-23

= 125°C, θJA = 250°CW

JMAX

MARKING

+

5 V

4 –IN

S5 PART

OUT 1

–

2

V

+IN 3

S6 PACKAGE

6-LEAD PLASTIC SOT-23

T

= 125°C, θJA = 230°CWT

JMAX

ORDER PART

NUMBER

Specified Temperature Range (Note 3).. –40°C to 85°C

Storage Temperature Range ................ –65°C to 150°C

Lead Temperature (Soldering, 10 sec)................. 300°C

U

TOP VIEW

TOP VIEW

+

6 V
5 SHDN
4 –IN

S6 PART

MARKING

SHDN

1

–IN

2

+IN

3

–

V

4

S8 PACKAGE

8-LEAD PLASTIC SO

T

= 125°C, θJA = 190°CW

JMAX

ORDER PART

NUMBER

8

7

6

5

S8 PART

MARKING

NC
V
OUT
NC

+

LTC2050CS5

LTIN

LTC2050CS6

LTIP

LTC2050CS8
LTC2050IS8

Consult factory for Military grade parts.

LECTRICAL C CHARA TERIST

E

temperature range, otherwise specifications are at TA = 25°C. VS = 3V unless otherwise noted. (Note 3)

PARAMETER CONDITIONS MIN TYP MAX UNITS

Input Offset Voltage (Note 2) ±0.5 ±3 µV
Average Input Offset Drift (Note 2) ● ±0.03 µV/°C
Long-Term Offset Drift 50 nV/√mo
Input Bias Current ±20 ±75 pA

Input Offset Current ±150 pA

Input Noise Voltage RS = 100Ω, DC to 10Hz 1.5 µV
Common Mode Rejection Ratio VCM = V– to V+ – 1.3 115 130 dB

Power Supply Rejection Ratio 120 130 dB

Large-Signal Voltage Gain RL = 10k 120 140 dB

Maximum Output Voltage Swing RL = 2k ● 2.85 2.94 V

Slew Rate 2V/µs
Gain Bandwidth Product 3 MHz
Supply Current V

ICS

R

= 10k ● 2.95 2.98 V

L

= V+, No Load ● 0.75 1.1 mA

SHDN

V

= V

SHDN

The ● denotes the specifications which apply over the full operating

● ±300 pA

● ±200 pA

● 110 130 dB

● 115 130 dB

● 115 140 dB

–

● 10 µA

2050
2050I

P-P

2

LTC2050

LECTRICAL C CHARA TERIST

E

ICS

The ● denotes the specifications which apply over the full operating

temperature range, otherwise specifications are at TA = 25°C. VS = 3V unless otherwise noted. (Note 3)

PARAMETER CONDITIONS MIN TYP MAX UNITS

Shutdown Pin Input Low Voltage ● V– + 0.5 V
Shutdown Pin Input High Voltage ● V+ – 0.5 V
Shutdown Pin Input Current V
Internal Sampling Frequency 7.5 kHz

SHDN

= V

–

● –0.5 –3 µA

The ● denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25°C.
VS = 5V unless otherwise noted. (Note 3)

PARAMETER CONDITIONS MIN TYP MAX UNITS

Input Offset Voltage (Note 2) ±0.5 ±3 µV
Average Input Offset Drift (Note 2) ● ±0.03 µV/°C
Long-Term Offset Drift 50 nV/√mo
Input Bias Current ±150 pA

● ±300 pA

Input Offset Current ±300 pA

● ±400 pA

Input Noise Voltage RS = 100Ω, DC to 10Hz 1.5 µV
Common Mode Rejection Ratio VCM = V– to V+ – 1.3 120 130 dB

● 115 130 dB

Power Supply Rejection Ratio 120 130 dB

● 115 130 dB

Large-Signal Voltage Gain RL = 10k 125 140 dB

● 120 140 dB

Maximum Output Voltage Swing RL = 2k ● 4.85 4.94 V

R

= 10k ● 4.95 4.98 V

L

Slew Rate 2V/µs
Gain Bandwidth Product 3 MHz
Supply Current V

Shutdown Pin Input Low Voltage ● V– + 0.5 V
Shutdown Pin Input High Voltage ● V+ – 0.5 V
Shutdown Pin Input Current V
Internal Sampling Frequency 7.5 kHz

= V+, No Load ● 0.8 1.2 mA

SHDN
SHDN

SHDN

= V

= V

–

–

● 10 µA

● –0.5 – 5 µA

V

P-P

Note 1: Absolute Maximum Ratings are those values beyond which the life
of the device may be impaired.

Note 2: These parameters are guaranteed by design. Thermocouple effects
preclude measurements of these voltage levels during automated testing.

Note 3: The LTC2050C is guaranteed to meet specified performance from
0°C to 70°C and is designed, characterized and expected to meet these
extended temperature limits, but is not tested at –40°C and 85°C. The
LTC2050I is guaranteed to meet the extended temperature limits.

3

LTC2050

PACKAGE DESCRIPTION

2.60 – 3.00

(0.102 – 0.118)

1.50 – 1.75

(0.059 – 0.069)

0.35 – 0.55

(0.014 – 0.022)

NOTE:

1. DIMENSIONS ARE IN MILLIMETERS

2. DIMENSIONS ARE INCLUSIVE OF PLATING

3. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR

4. MOLD FLASH SHALL NOT EXCEED 0.254mm

5. PACKAGE EIAJ REFERENCE IS SC-74A (EIAJ)

2.6 – 3.0

(0.110 – 0.118)

1.50 – 1.75

(0.059 – 0.069)

U

Dimensions in inches (millimeters) unless otherwise noted.

S5 Package

5-Lead Plastic SOT-23

(LTC DWG # 05-08-1633)

2.80 – 3.00

(0.110 – 0.118)

(NOTE 3)

(0.074)

2.80 – 3.00

(0.110 – 0.118)

(NOTE 3)

1.90

REF

0.09 – 0.20

(0.004 – 0.008)

(NOTE 2)

0.00 – 0.15

(0.00 – 0.006)

0.35 – 0.50

(0.014 – 0.020)

FIVE PLACES (NOTE 2)

0.90 – 1.45

(0.035 – 0.057)

0.90 – 1.30

(0.035 – 0.051)

S6 Package

6-Lead Plastic SOT-23

(LTC DWG # 05-08-1634)

0.00 – 0.15

(0.00 – 0.006)

0.90 – 1.45

(0.035 – 0.057)

0.95

(0.037)

REF

S5 SOT-23 0599

0.35 – 0.55

(0.014 – 0.022)

NOTE:

1. DIMENSIONS ARE IN MILLIMETERS

2. DIMENSIONS ARE INCLUSIVE OF PLATING

3. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR

4. MOLD FLASH SHALL NOT EXCEED 0.254mm

5. PACKAGE EIAJ REFERENCE IS SC-74A (EIAJ)

0.09 – 0.20

(0.004 – 0.008)

(NOTE 2)

0.35 – 0.50

(0.014 – 0.020)

SIX PLACES (NOTE 2)

0.90 – 1.30

(0.035 – 0.051)

1.90

(0.074)

REF

0.95

(0.037)

REF

S6 SOT-23 0898

S8 Package

8-Lead Plastic Small Outline (Narrow 0.150)

(LTC DWG # 05-08-1610)

0.189 – 0.197*

0.010 – 0.020

(0.254 – 0.508)

0.008 – 0.010

(0.203 – 0.254)

*

DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH
SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE

**

DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE

× 45°

0.016 – 0.050

(0.406 – 1.270)

0°– 8° TYP

0.053 – 0.069

(1.346 – 1.752)

0.014 – 0.019

(0.355 – 0.483)

TYP

0.004 – 0.010

(0.101 – 0.254)

0.050

(1.270)

BSC

0.228 – 0.244

(5.791 – 6.197)

(4.801 – 5.004)

8

1

7

2

6

3

5

0.150 – 0.157**
(3.810 – 3.988)

4

SO8 1298

RELATED PARTS

PART NUMBER DESCRIPTION COMMENTS

LTC1049 Low Power Zero-Drift Op Amp Low Supply Current 200µA
LTC1050 Precision Zero-Drift Op Amp Single Supply Operation 4.75V to 16V, Noise Tested and Guaranteed
LTC1051/LTC1053 Precision Zero-Drift Op Amp Dual/Quad
LTC1150 ±15V Zero-Drift Op Amp High Voltage Operation ±18V
LTC1152 Rail-to-Rail Input and Output Zero-Drift Op Amp Single Zero-Drift Op Amp with Rail-to-Rail Input and Output and Shutdown

4

Linear Technology Corporation

1630 McCarthy Blvd., Milpitas, CA 95035-7417

[phone] ● FAX: [phone]

●

www.linear-tech.com

2050i LT/TP 1199 4K • PRINTED IN USA

 LINEAR TECHNOLOGY CORPORATION 1999