Datasheet LTC1553L Datasheet (Linear Technology)

FEATURES

■

5-Bit Digitally Programmable 1.8V to 3.5V Fixed
Output Voltage

■

Provides All Features Required by the

Intel
Pentium® II Processor VRM 8.2 DC/DC
Converter Specification

■

Flags for Power Good, Over-Temperature and
Overvoltage Fault

■

19A Output Current Capability from a 5V Supply

■

Dual N-Channel MOSFET Synchronous Driver

■

Initial Output Accuracy: ±1.5%

■

Excellent Output Accuracy: ±2% Typ Over Line,
Load and Temperature Variations

■

High Efficiency: Over 95% Possible

■

Adjustable Current Limit Without External Sense
Resistors

■

Fast Transient Response

■

Available in 2O-Lead SSOP and SW Packages

U

APPLICATIONS

■

Power Supply for Pentium II, SPARC, ALPHA and
PA-RISC Microprocessors

■

High Power 5V to 1.8V-3.5V Regulators

LTC1553L

5-Bit Programmable

Synchronous Switching

Regulator Controller for

®

Pentium

II Processor

U

DESCRIPTION

The LTC®1553L is a high power, high efficiency switching
regulator controller optimized for a 5V input to 1.8V-3.5V
output applications. It features a digitally programmable
output voltage, a precision internal reference and an internal
feedback system that provides output accuracy of ±1.5% at
room temperature and typically ±2% over-temperature, load
current and line voltage shifts. The LTC1553L uses a syn­chronous switching architecture with two external N-channel
output devices, providing high efficiency and eliminating the
need for a high power, high cost P-channel device. Addition­ally, it senses the output current across the on-resistance of
the upper N-channel FET, providing an adjustable current
limit without an external low value sense resistor.

The LTC1553L free-runs at 300kHz and can be synchronized
to a faster external clock if desired. It includes all the inputs
and outputs required to implement a power supply conform­ing to the

Converter Specification

, LTC and LT are registered trademarks of Linear Technology Corporation.

Pentium is a registered trademark of Intel Corporation.

Intel Pentium® II Processor VRM 8.2 DC/DC

.

TYPICAL APPLICATION

5.6k

5.6k

PENTIUM® II

SYSTEM

C1
150pF

5

U

5.6k

R

8.2k



C

CC

0.01µF

+

0.1µF

10µF CIN**

PWRGD
FAULT
OT
VID0 TO VID4
OUTEN
COMP

C

SS

0.1µF

V

SS SGND GND SENSE



CC

LTC1553L

PV

CC

12V

2.7k

I

MAX

0.1µF

PV

CC

G1

I



FB

G2



0.1µF

Figure 1. 5V to 1.8V-3.5V Supply Application

V

IN

5V

+

10µF

Q1*

20Ω

Q2*

 *SILICONIX SUD50N03-10
**SANYO 10MV1200GX



†

COILTRONICS CTX02-13198 OR

 PANASONIC 12TS-2R5SP

††

AVX TPSE337M006R0100



+

L

2µH
18A

1200µF
× 4

O†

††



C

+

OUT

330µF

× 7

V

OUT

1.8V TO

3.5V
14A

1553L F01



1

LTC1553L

WW

W

U

ABSOLUTE MAXIMUM RATINGS

(Note 1)

Supply Voltage

VCC........................................................................ 7V

PVCC................................................................... 14V

Input Voltage

IFB (Note 2)............................................ PVCC + 0.3V

I

........................................................ – 0.3V to 9V

MAX

All Other Inputs ......................... – 0.3V to VCC + 0.3V

Digital Output Voltage................................. – 0.3V to 9V

IFB Input Current (Notes 2, 3) .......................... –100mA

Operating Temperature Range ..................... 0°C to 70°C

Storage Temperature Range ................. – 65°C to 150°C

Lead Temperature (Soldering, 10 sec.)................. 300°C

ELECTRICAL CHARACTERISTICS

VCC = 5V, PVCC = 12V, TA = 25°C, unless otherwise noted. (Note 3)

U

W

PACKAGE/ORDER INFORMATION

TOP VIEW

1

G2

2

PV



CC

3

GND

4

SGND

5

V



CC

6

SENSE

7

I



MAX

8

I



FB

9

SS

10

COMP

G PACKAGE

20-LEAD PLASTIC SSOP

T

= 125°C, θJA = 100°C/ W (G)

JMAX

= 125°C, θJA = 100°C/ W (SW)

T

JMAX

20-LEAD PLASTIC SO

G1

20

OUTEN

19

VID0

18

VID1

17

VID2

16

VID3

15

VID4

14

PWRGD

13

FAULT

12

OT

11





SW PACKAGE



Consult factory for Industrial and Military grade parts.

ORDER PART

NUMBER

LTC1553LCG
LTC1553LCSW

U

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS

V
PV
V
V

CC

CC

FB

OUT

Supply Voltage ● 4.5 6 V
Supply Voltage for G1, G2 ● 13.2 V
Internal Feedback Voltage (Note 4) 1.260 V

1.8V Initial Output Voltage With Respect to Rated Output Voltage (Figure 2) – 27 (– 1.5%) 27 (+1.5%) mV

2.8V Initial Output Voltage – 42 (–1.5%) 42 (+ 1.5%) mV

3.5V Initial Output Voltage – 52 (–1.5%) 52 (+1.5%) mV

1.8V Initial Output Voltage

2.8V Initial Output Voltage

3.5V Initial Output Voltage

∆V

OUT

Output Load Regulation I
Output Line Regulation V

V

PWRGD

Positive Power Good Trip Point % Above Output Voltage (Figure 2) ● 57 %
Negative Power Good Trip Point % Below Output Voltage (Figure 2)

V

FAULT

I

CC

FAULT Trip Point % Above Output Voltage (Figure 2) ● 12 15 20 %
Operating Supply Current OUTEN = VCC = 5V (Note 5)(Figure 3) ● 800 1200 µA

Shutdown Supply Current OUTEN = 0, VID0 to VID4 Floating (Figure 3)

I

PVCC

f

OSC

V

SAWL

V

SAWH

G

ERR

g

mERR

BW

ERR

Supply Current PVCC = 12V, OUTEN = VCC (Note 6) (Figure 3) 15 mA

Internal Oscillator Frequency (Figure 4) ● 250 300 350 kHz
V

at Minimum Duty Cycle (Note 4) 1.8 V

COMP

V

at Maximum Duty Cycle (Note 4) 2.8 V

COMP

Error Amplifier Open-Loop DC Gain (Note 7) ● 40 53 dB
Error Amplifier Transconductance (Note 7) ● 0.9 1.6 2.3 millimho
Error Amplifier –3dB Bandwidth COMP = Open (Note 4) 400 kHz

= 0 to 14A (Note 4) (Figure 2) –5 mV

OUT

= 4.75V to 5.25V, I

IN

= 12V, OUTEN = 0, VID0 to VID4 Floating 1 µA

PV

CC

= 0 (Note 4)(Figure 2) ±1mV

OUT

● – 36 (–2%) 36 (+2%) mV

● – 56 (–2%) 56 (+2%) mV

● – 70 (–2%) 70 (+2%) mV

● –7 –5 %

● 130 250 µA

2

LTC1553L

ELECTRICAL CHARACTERISTICS

VCC = 5V, PVCC = 12V, TA = 25°C, unless otherwise noted. (Note 3)

SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS

I

IMAX

I

SS

I

SSIL

I

SSHIL

I

Sink Current V

MAX

Soft Start Source Current VSS = 0V, V
Maximum Soft Start Sink Current V

IMAX

SENSE

= V

= V

CC

IMAX

OUT

Under Current Limit (Notes 8, 9), V
Soft Start Sink Current Under Hard V

SENSE

= 0V, V

= 0V, V

, V

IMAX

= V

SS

IMAX

IFB

= VCC, V

CC

= VCC, V

● 150 180 220 µA

= V

CC

= 0V ● 30 60 150 µA

IFB

= 0V ● 20 45 mA

IFB

● –15 –11 –8 µA

Current Limit

t

SSHIL

t

PWRGD

t

PWRBAD

t

FAULT

t

OT

V

OT

V

OTDD

V

SHDN

tr, t

f

t

NOL

DC

MAX

V

IH

V

IL

R

IN

Hard Current Limit Hold Time V
Power Good Response Time↑ V
Power Good Response Time↓ V
FAULT Response Time V

= 0V, V

SENSE

↑ from 0V to Rated V

SENSE

↓ from Rated V

SENSE

↑ from Rated V

SENSE

IMAX

= 4V, V

↓ from 5V (Note 4) 500 µs

IFB

OUT

to 0V ● 200 500 1000 µs

OUT

to V

OUT

CC

● 0.5 1 2 ms

● 200 500 1000 µs

OT Response Time OUTEN↓, VID0 to VID4 = 0 (Note 10) (Figure 3) ● 15 40 60 µs
Over-Temperature Trip Point OUTEN↓, VID0 to VID4 = 0 (Note 10) (Figure 3) ● 1.9 2 2.12 V
Over-Temperature Driver Disable OUTEN↓, VID0 to VID4 = 0 (Note 10) (Figure 3) ● 1.6 1.7 1.8 V
Shutdown OUTEN↓, VID0 to VID4 = 0 (Note 10) (Figure 3) ● 0.8 V
Driver Rise and Fall Time (Figure 4) ● 90 150 ns
Driver Nonoverlap Time (Figure 4) ● 30 100 ns
Maximum G1 Duty Cycle (Figure 4) ● 77 85 90 %
VID0 to VID4 Input High Voltage ● 2V
VID0 to VID4 Input Low Voltage ● 0.8 V
VID0 to VID4 Internal Pull-Up ● 10 20 kΩ

Resistance

I

SINK

Digital Output Sink Current ● 10 mA

The ● denotes specifications which apply over the full operating
temperature range.

Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.

Note 2: When I

is taken below GND, it will be clamped by an internal

FB

diode. This pin can handle input currents greater than 100mA below GND
without latchup. In the positive direction, it is not clamped to V

or PVCC.

CC

Note 3: All currents into device pins are positive; all currents out of the
device pins are negative. All voltages are referenced to ground unless
otherwise specified.

Note 4: This parameter is guaranteed by correlation and is not tested
directly.

Note 5: The LTC1553L goes into the shutdown mode if VID0 to VID4 are
floating. Due to the internal pull-up resistors, there will be an additional

0.25mA/pin if any of the VID0 to VID4 pins are pulled low.

Note 6: Supply current in normal operation is dominated by the current
needed to charge and discharge the external FET gates. This will vary with
the LTC1553L operating frequency, supply voltage and the external FETs
used.

Note 7: The open-loop DC gain and transconductance from the SENSE pin to
COMP pin will be (G

)(1.260/3.3) and (g

ERR

)(1.260/3.3) respectively.

mERR

Note 8: The current limiting amplifier can sink but cannot source current.
Under normal (not current limited) operation, the output current will be zero.

Note 9: Under typical soft current limit, the net soft start discharge current
will be 60µA (I

) + [–11µA(ISS)] ≅ 50µA. The soft start sink-to-source

SSIL

current ratio is designed to be 5.5:1.
Note 10: When VID0 to VID4 are all HIGH, the LTC1553L will be forced to

shut down internally. The OUTEN trip voltages are guaranteed by design for
all other input codes.

3

LTC1553L

TEMPERATURE (°C)

–50

OVER-TEMPERATURE TRIP POINT (V)

1.96

2.08

2.10

2.12

0

50

75

1553L G06

1.92

2.04

2.00

1.94

2.06

1.90

2.02

1.98

–25

25

100

125

TEMPERATURE (°C)

–50

40

ERROR AMPLIFIER OPEN-LOOP DC GAIN (dB)

45

50

55

60

–25 0 25 50

1553L G09

75 100 125

UW

TYPICAL PERFORMANCE CHARACTERISTICS

Typical 2.8V V

140

TOTAL SAMPLE SIZE = 1500

120

100

80

60

NUMBER OF UNITS

40

20

0

2.775

2.785

25°C 100°C

OUTPUT VOLTAGE (V)

Distribution Load Regulation

OUT

2.795

2.805 2.815

2.825

1553L G01

Efficiency vs Load Current

100

90

A

B

80

70

REFER TO TYPICAL APPLICATION

60

CIRCUIT FIGURE 1

= 5V, PVCC = 12V, V

V

50

IN

= 330µF ×7, LO = 2µH

C

OUT

40

EFFICIENCY (%)

A: Q1 = 1 × SUD50N03-10
Q2 = 1 × SUD50N03-10

30

B: Q1 = 2 × SUD50N03-10

20

Q2 = 1 × SUD50N03-10
NO FAN

10

Q1 IS MOUNTED ON 1IN


0



0

2

0.3

4

LOAD CURRENT (A)

Line Regulation Output Temperature Drift

2.825
REFER TO TYPICAL APPLICATION 

2.820

CIRCUIT FIGURE 1
OUTPUT = NO LOAD

2.815

2.810

2.805

2.800

2.795

2.790

OUTPUT VOLTAGE (V)

2.785

2.780

2.775

4.75

T

A

= 25°C

4.85

5.05

4.95

INPUT VOLTAGE (V)

5.15

5.25

1553L G04

2.860

2.850

2.840

2.830

2.820

2.810

2.800

2.790

2.780

OUTPUT VOLTAGE (V)

2.770

2.660

2.750

2.740
–50

–25

0

TEMPERATURE (°C)

= 2.8V, 

OUT

2

COPPER AREA

6 8 10 12 14

1533L G02

50

25

75

100

1553L G05

2.825

2.820

2.815

2.810

2.805

2.800

2.795

2.790

OUTPUT VOLTAGE (V)

2.785

2.780

2.775

125

REFER TO TYPICAL APPLICATION
CIRCUIT FIGURE 1

= 5V, PVCC = 12V, TA = 25°C

V

IN

123

0

4

67891011121314

5

OUTPUT CURRENT (A)

Over-Temperature Trip Point
vs Temperature

1533L G03

Over-Temperature Driver Disable
vs Temperature

1.80

1.78

1.76

1.74

1.72

1.70

1.68

1.66

1.64

1.62

OVER-TEMPERATURE DRIVER DISABLE (V)

1.60

4

–50

–25

0

TEMPERATURE (°C)

25

50

Error Amplifier Transconductance
vs Temperature

2.3

2.1

1.9

1.7



1.5

1.3

1.1

100

125

1553L G07

75

0.9

ERROR AMPLIFIER TRANSCONDUCTANCE (millimho)

–50

–25 0

TEMPERATURE (°C)

50 100 125

25 75

1553L G08

Error Amplifier Open-Loop
DC Gain vs Temperature

UW

TEMPERATURE (°C)

–50

SOFT START SOURCE CURRENT (µA)

–9

–8

25 75

1553L G12

–10

–11

–25 0

50 100 125

–12

–13

–14

–15

TEMPERATURE (°C)

–50

V

CC

SHUTDOWN SUPPLY CURRENT (mA)

225

25

1553L G15

150

100

–25 0 50

75

50

250

200

175

125

75 100 125

TYPICAL PERFORMANCE CHARACTERISTICS

LTC1553L

Oscillator Frequency
vs Temperature

350
340
330
320
310
300
290
280
270

OSCILLATOR FREQUENCY (kHz)

260
250

–50

–25

25

0

TEMPERATURE (°C)

Maximum G1 Duty Cycle
vs Temperature

92

OSCILLATOR FREQUENCY = 300kHz

90

G1, G2 CAPACITANCE = 1100pF

88

86

84

82

80

MAXIMUM G1 DUTY CYCLE (%)

78

–50

–25 0

5500pF
7700pF

25 75

TEMPERATURE (°C)

50

75

50 100 125

100

1553L G10

2200pF
3300pF

1553L G13

125

I

Sink Current

MAX

vs Temperature

220

210

200

190

180

SINK CURRENT (µA)

170

MAX

I

160

150

–50

0

–25

TEMPERATURE (°C)

25

VCC Operating Supply Current
vs Temperature

1.2
VCC = 5V

= 300kHz

f

OSC

1.1

1.0

0.9



0.8

0.7

OPERATING SUPPLY CURRENT (mA)

0.6

CC

V

0.5

–50

–25 0

25 75

TEMPERATURE (°C)

75

50 125

50 100 125

100

1553L G11

1553L G14

Soft Start Source Current
vs Temperature

VCC Shutdown Supply Current
vs Temperature

PVCC Supply Current
vs Gate Capacitance

70

PVCC = 12V

= 25°C

T

A

60

50

40

30

SUPPLY CURRENT (mA)

20

CC

PV

10

0

2000 4000 8000

0

GATE CAPACITANCE (pF)

6000

1553L G16

Output Over Current Protection

3.0

Q1 CASE = 90°C, V

2.5

Q1 = 2 × MTD20N03HDL
Q2 = 1 × MTD20N03HDL

2.0

1.5

1.0

OUTPUT VOLTAGE (V)

0.5

= 2.7k, R

R

IMAX

SS CAP = 0.01µF

SHORT-CIRCUIT

CURRENT

0

26

0

4

OUTPUT CURRENT (A)

= 2.8V

OUT

= 20Ω,

IFB

10 18

8

Transient Response

50mV/DIV

5A/DIV

100µs/DIV

14

12

16

1553L G17

1553L G18

5

LTC1553L

UUU

PIN FUNCTIONS

G2 (Pin 1): Gate Drive for the Lower N-Channel MOSFET,
Q2. This output will swing from PVCC to GND. It will always
be low when G1 is high or when the output is disabled. To
prevent undershoot during a soft start cycle, G2 is held low
until G1 first goes high.

PVCC (Pin 2): Power Supply for G1 and G2. PVCC must be
connected to a potential of at least VIN + V
VIN = 5V, PVCC can be generated using a simple charge
pump connected to the switching node between Q1 and
Q2 (see Figure 7), or it can be connected to an auxiliary 12V
supply if one exists.

GND (Pin 3): Power Ground. GND should be connected to
a low impedance ground plane in close proximity to the
source of Q2.

SGND (Pin 4): Signal Ground. SGND is connected to the
low power internal circuitry and should be connected to
the negative terminal of the output capacitor where it
returns to the ground plane. GND and SGND should be
shorted right at the LTC1553L.

VCC (Pin 5): Power Supply. Power for the internal low
power circuity. VCC should be wired separately from the
drain of Q1 if they share the same supply. A 10µ F bypass
capacitor is recommended from this pin to SGND.

SENSE (Pin 6): Output Voltage Pin. Connect to the positive
terminal of the output capacitor. There is an internal 120k
resistor connected from this pin to SGND. SENSE is a very
sensitive pin; for optimum performance, connect an exter­nal 0.1µ F capacitor from this pin to SGND. By connecting
a small external resistor between the output capacitor and
the SENSE pin, the initial output voltage can be raised
slightly. Since the internal divider has a nominal imped­ance of 120kΩ, a 1200Ω series resistor will raise the
nominal output voltage by 1%. If an external resistor is
used, the value of the 0.1µF capacitor on the SENSE pin
must be greatly reduced or loop phase margin will suffer.
Set a time constant for the RC combination of approxi­mately 0.1µ s. So, for example, with a 1200Ω resistor, set
C = 83pF. Use a standard 100pF capacitor.

GS(ON)Q1

. If

I

(Pin 7): Current Limit Threshold. Current limit is set

MAX

by the voltage drop across an external resistor connected
between the drain of Q1 and I
pull-down at I

IFB (Pin 8): Current Limit Sense Pin. Connect to the
switching node between the source of Q1 and the drain of
Q2. If IFB drops below I
will go into current limit. The current limit circuit can be
disabled by floating I
an external 10k resistor.

SS (Pin 9): Soft Start. Connect to an external capacitor to
implement a soft start function. During moderate overload
conditions, the soft start capacitor will be discharged
slowly in order to reduce the duty cycle. In hard current
limit, the soft start capacitor will be forced low immedi­ately and the LTC1553L will rerun a complete soft start
cycle. CSS must be selected such that during power-up the
current through Q1 will not exceed the current limit value.

COMP (Pin 10): External Compensation. The COMP pin is
connected directly to the output of the error amplifier and
the input of the PWM comparator. An RC+C network is
used at this node to compensate the feedback loop to
provide optimum transient response.

OT (Pin 11): Over-Temperature Fault. OT is an open-drain
output and will be pulled low if OUTEN is less than 2V. If
OUTEN = 0, OT pulls low.

FAULT (Pin 12): Overvoltage Fault. FAULT is an open­drain output. If V
output voltage, FAULT will go low and G1 and G2 will be
disabled. Once triggered, the LTC1553L will remain in this
state until the power supply is recycled or the OUTEN pin
is toggled. If OUTEN = 0, FAULT floats or is pulled high by
an external resistor.

PWRGD (Pin 13): Power Good. This is an open-drain
signal to indicate validity of output voltage. A high indi­cates that the output has settled to within ±5% of the rated
output for more than 1ms. PWRGD will go low if the output
is out of regulation for more than 500µs. If OUTEN = 0,
PWRGD pulls low.

MAX

.

MAX

and shorting IFB to VCC through

MAX

reaches 15% above the nominal

OUT

. There is a 180µ A internal

MAX

when G1 is on, the LTC1553L

6

UUU

PIN FUNCTIONS

LTC1553L

VID0, VID1, VID2, VID3, VID4 (Pins 18, 17, 16, 15, 14):

Digital Voltage Select. TTL inputs used to set the regulated
output voltage required by the processor (Table 3). There
is an internal 20kΩ pull-up at each pin. When all five VID

n

pins are high or floating, the chip will shut down.
OUTEN (Pin 19): Output Enable. TTL input which enables

the output voltage. The external MOSFET temperature can
be monitored with an external thermistor as shown in
Figure 11. When the OUTEN input voltage drops below 2V,

W

BLOCK DIAGRAM

OUTEN

COMP

19

10

115% V

REF

+

FC

FAULT

12

OT

11

–

LOGIC

–

PWM

R
S

+

OT trips. As OUTEN drops below 1.7V, the drivers are
internally disabled to prevent the MOSFETs from heating
further. If OUTEN is less than 1.2V for longer than 30µs,
the LTC1553L will enter shutdown mode. The internal
oscillator can be synchronized to a faster external clock by
applying the external clocking signal to the OUTEN pin.

G1 (Pin 20): Gate Drive for the Upper N-Channel MOSFET,
Q1. This output will swing from PVCC to GND. It will always
be low when G2 is high or the output is disabled.

DISDR

SYSTEM
POWER
DOWN

DELAY

13

2

20

PWRGD

PV

G1

CC

I

SS

SS

9

Q

SS

ERR

+

–

V

REF

HCL MONOMHCL

MIN

+

–

V

– 5% V

REF

–

CC

+

I

MAX

8

7

REF

LVC

I

FB

I

MAX

+ 5%

MAX

–+

+

0.5V

0.7V

REF
REF

FB

V

REF

/

BG

DAC

–

1

6

18

17

16

15

14

G2

SENSE

VID0

VID1

VID2

VID3

VID4

1553 BD

7

LTC1553L



TEST CIRCUITS

100pF

100pF

0.1µF

PV

PV

12V

CC

CC

0.1µF

I

I

FB

MAX

V

IN

5V

CIN**

+

L
2µH
15A

O†

1200µF
× 4

C

OUT

330µF

× 7

V

††



+

OUT

1553L F02

10k

G1

NC



G2



Q1*

Q2*

 *SILICONIX SUD50N03-10
**SANYO 10MV1200GX

 †

COILTRONICS CTX02-13198 OR

 PANASONIC 12TS-2R5SP

 ††

AVX TPSE337M006R0100

V

CC

5V

3k3k

3k

100pF

VID0 TO VID4

C1
150pF

10µF

R

8.2k



C

CC

0.01µF

0.1µF

OUTEN
PWRGD
FAULT
OT
VID0 TO VID4
COMP

0.1µF

++

10µF

V

CC

LTC1553L



SS SGND GND SENSE

Figure 2

V

CC

V

CC

NC
NC
NC
NC

VID0 VID1 VID2 VID3 VID4

VID0 VID1 VID2 VID3 VID4

OUTEN
PWRGD
FAULT
OT
COMP

SS SGND GND SENSE

LTC1553L

10k

V

I

CC

FB

PV

CC

G1

I

MAX

G2

0.1µF

PV

NC



NC

NC





+

10µF

CC

+

0.1µF

10µF

8

NC

1553L F03

Figure 3

V

PV

CC

CC

5V

12V

+

10µF

0.1µF

10k

I

FB

SENSE

SGND GND

V

CC

LTC1553L

PV

CC

G1

G2

0.1µF

5000pF

5000pF

+

10µF

G1 RISE/FALL

G2 RISE/FALL

t

r

90%

50%

10%

t

NOL

50% 50%

90%

50%

10%

t

f

t

NOL

1553L F04

Figure 4

U U

FU CTIO TABLES

LTC1553L

Table 1. OT Logic

OUTEN (V) OT*

< 2 0
> 2 1

Table 2. PWRGD and FAULT Logic

INPUT OUTPUT*

OUTEN V

0 X 010
1 < 95% 1 1 0
1 > 95% 1 1 1

1 >105% 1 1 0
1 > 115% 1 0 0

** OT FAULT PWRGD

SENSE

< 105%

Table 3. Rated Output Voltage

INPUT PIN

V

V

ID4

01111Disabled† (1.30)
01110Disabled† (1.35)
01101Disabled† (1.40)
01100Disabled† (1.45)
01011Disabled† (1.50)
01010Disabled† (1.55)
01001Disabled† (1.60)
01000Disabled† (1.65)
00111Disabled† (1.70)
00110Disabled† (1.75)

ID3

V

ID2

V

ID1

V

ID0

RATED OUTPUT

VOLTAGE (V)

Table 3. Rated Output Voltage (cont)

INPUT PIN

V

* With external pull-up resistor

** With respect to the output voltage selected in Table 3 as required by

†

X Don’t care

V

ID4

00101 1.80
00100 1.85
00011 1.90
00010 1.95
00001 2.00
00000 2.05
11111 SHDN
11110 2.1
11101 2.2
11100 2.3
11011 2.4
11010 2.5
11001 2.6
11000 2.7
10111 2.8
10110 2.9
10101 3.0
10100 3.1
10011 3.2
10010 3.3
10001 3.4
10000 3.5

ID3

Intel Specification VRM 8.2
These code selections are disabled in LTC1553L

V

ID2

V

ID1

V

ID0

RATED OUTPUT

VOLTAGE (V)

9

LTC1553L

U

WUU

APPLICATIONS INFORMATION

OVERVIEW

The LTC1553L is a voltage feedback, synchronous switch­ing regulator controller (see Block Diagram) designed for
use in high power, low voltage step-down (buck) convert­ers. It is designed to satisfy the requirements of the Intel
Pentium II power supply specification. It includes an
on-chip DAC to control the output voltage, a PWM genera­tor, a precision reference trimmed to ± 1%, two high power
MOSFET gate drivers and all the necessary feedback and
control circuitry to form a complete switching regulator
circuit.

The LTC1553L includes a current limit sensing circuit that
uses the upper external power MOSFET as a current
sensing element, eliminating the need for an external
sense resistor. Once the current comparator, CC, detects
an overcurrent condition, the duty cycle is reduced by
discharging the soft start capacitor through a voltage­controlled current source. Under severe overloads or
output short circuit conditions, the chip will be repeatedly
forced into soft start until the short is removed, preventing
the external components from being damaged. Under
output overvoltage conditions, the MOSFET drivers will be
disabled permanently until the chip power supply is
recycled or the OUTEN pin is toggled.

Output regulation can be monitored with the PWRGD pin
which in turn monitors the internal MIN and MAX com­parators. If the output is ±5% beyond the selected value
for more than 500µs, the PWRGD output will be pulled
low. Once the output has settled within ±5% of the
selected value for more than 1ms, PWRGD will return
high.

THEORY OF OPERATION

Primary Feedback Loop

The regulator output voltage at the SENSE pin is divided
down internally by a resistor divider with a total resistance
of approximately 120kΩ. This divided down voltage is
subtracted from a reference voltage supplied by the DAC
output. The resulting error voltage is amplified by the error
amplifier and the output is compared to the oscillator ramp
waveform by the PWM comparator. This PWM signal
controls the external MOSFETs through G1 and G2. The
resulting chopped waveform is filtered by LO and C
closing the loop. Loop frequency compensation is achieved
with an external RC + C network at the COMP pin, which is
connected to the output node of the transconductance
amplifier.

OUT

OUTEN can optionally be connected to an external nega­tive temperature coefficient (NTC) thermistor placed near
the external MOSFETs or the microprocessor. Three thresh­old levels are provided internally. When OUTEN drops to
2V, OT will trip, issuing a warning to the external CPU. If
the temperature continues to rise and the OUTEN input
drops to 1.7V, the G1 and G2 pins will be forced low. If
OUTEN is pulled below 1.2V, the LTC1553L will go into
shutdown mode, cutting the supply current to a minimum.
If thermal shutdown is not required, OUTEN can be con­nected to a conventional TTL enable signal. The free­running 300kHz PWM frequency can be synchronized to
a faster external clock connected to OUTEN. Adjusting the
oscillator frequency can add flexibility in the external
component selection. See the Clock Synchronization
section.

MIN, MAX Feedback Loops

Two additional comparators in the feedback loop provide
high speed fault correction in situations where the ERR
amplifier may not respond quickly enough. MIN compares
the feedback signal FB to a voltage 60mV (5%) below the
internal reference. If FB is lower than the threshold of this
comparator, the MIN comparator overrides the ERR
amplifier and forces the loop to full duty cycle which is set
by the internal oscillator typically to 85%. Similarly, the
MAX comparator forces the output to 0% duty cycle if FB
is more than 5% above the internal reference. To prevent
these two comparators from triggering due to noise, the
MIN and MAX comparators’ response times are deliber­ately controlled so that they take two to three microsec­onds to respond. These two comparators help prevent
extreme output perturbations with fast output transients,
while allowing the main feedback loop to be optimally
compensated for stability.

10

LTC1553L

Q1

180µA

G1

Q2

C

IN

L

O

V

OUT

1553L F05

C

OUT

R

IMAX

V

IN

–

+

CC

G2

20Ω

LTC1553L

I

MAX

I

FB

8

7

+

+

U

WUU

APPLICATIONS INFORMATION

Soft Start and Current Limit

The LTC1553L includes a soft start circuit which is used
for initial start-up and during current limit operation. The
SS pin requires an external capacitor to GND with the value
determined by the required soft start time. An internal
11µA current source is included to charge the external SS
capacitor. During start-up, the COMP pin is clamped to a
diode drop above the voltage at the SS pin. This prevents
the error amplifier, ERR, from forcing the loop to maxi­mum duty cycle. The LTC1553L will begin to operate at low
duty cycle as the SS pin rises above about 1.2V (V

1.8V). As SS continues to rise, QSS turns off and the error
amplifier begins to regulate the output. The MIN compara­tor is disabled when soft start is active to prevent it from
overriding the soft start function.

The LTC1553L includes yet another feedback loop to
control operation in current limit. Just before every falling
edge of G1, the current comparator, CC, samples and
holds the voltage drop measured across the external
MOSFET, Q1, at the IFB pin. CC compares the voltage at I
to the voltage at the I

pin. As the peak current rises, the

MAX

measured voltage across Q1 increases due to the drop
across the R
below I

, indicating that Q1’s drain current has ex-

MAX

of Q1. When the voltage at IFB drops

DS(ON)

ceeded the maximum level, CC starts to pull current out of
the external soft start capacitor, cutting the duty cycle and
controlling the output current level. The CC comparator
pulls current out of the SS pin in proportion to the voltage
difference between IFB and I

. Under minor overload

MAX

conditions, the SS pin will fall gradually, creating a time
delay before current limit takes effect. Very short, mild
overloads may not affect the output voltage at all. More
significant overload conditions will allow the SS pin to
reach a steady state, and the output will remain at a
reduced voltage until the overload is removed. Serious
overloads will generate a large overdrive at CC, allowing it
to pull SS down quickly and preventing damage to the
output components.

COMP

≈

FB

helps minimize the number of components in the high
current path. Due to switching noise and variation of
R

, the actual current limit trip point is not highly

DS(ON)

accurate. The current limiting circuitry is primarily meant
to prevent damage to the power supply circuitry during
fault conditions. The exact current level where the limiting
circuit begins to take effect will vary from unit to unit as the
R

DS(ON)

of Q1 varies.

For a given current limit level, the external resistor from
I

to VIN can be determined by:

MAX

IR

()( )

R

IMAX

LMAX DS ON Q

=

()1

I

IMAX

where,

I

II

I

LOAD

I

RIPPLE

=+

LMAX LOAD

= Maximum load current

= Inductor ripple current

VV V

()()

IN OUT OUT

RIPPLE

2

−

=

fLV

()()()

OSC O IN

f

= LTC1553L oscillator frequency = 300kHz

OSC

LO = Inductor value
R

DS(ON)Q1

I

IMAX

= Hot on-resistance of Q1 at I

= Internal 180µA sink current at I

LMAX

MAX

By using the R

DS(ON)

the current limiting circuit eliminates an expensive dis­crete sense resistor that would otherwise be required. This

of Q1 to measure the output current,

Figure 5. Current Limit Setting

11

LTC1553L

U

WUU

APPLICATIONS INFORMATION

Table 4. Recommended Minimum R

MAXIMUM OPERATING SUD50N03-10 MTD20N03HDL

LOAD CURRENT (A) SUD50N03-10 (TWO IN PARALLEL) MTD20N03HDL (TWO IN PARALLEL)

12 2.4 1.2 4.3 2.2
14 2.7 1.3 5.1 2.7
16 3.0 1.5 6.2 3.0
18 3.6 1.8 6.8 3.3
20 3.9 2.0 7.5 3.6

OUTEN and Thermistor Input

The LTC1553L includes a low power shutdown mode,
controlled by the logic at the OUTEN pin. A high at OUTEN
allows the part to operate normally. A low level at OUTEN
stops all internal switching, pulls COMP and SS to ground
internally and turns Q1 and Q2 off. OT and PWRGD are
pulled low, and FAULT is left floating.
LTC1553L quiescent current will drop to about 130µA.
The remaining current is used to keep the thermistor
sensing circuit at OUTEN alive. Note that the leakage
current of the external MOSFETs may add to the total
shutdown current consumed by the circuit, especially at
elevated temperature.

Resistor (kΩ) vs Maximum Operating Load Current and External MOSFET Q1

IMAX

V

CC

5.6k

In shutdown, the

PENTIUM II

SYSTEM

NTC THERMISTOR

MOUNT IN CLOSE

THERMAL PROXIMITY

TO Q1

Figure 6. OUTEN Pin as a Thermistor Input

OT

V

CC

R1

R2

OUTEN

G1

LTC1553L

G2

Clock Synchronization

V

IN

Q1

L

O

Q2

V

OUT

+

C

OUT

1553L F06

OUTEN is designed with multiple thresholds to allow it to
also be utilized for over-temperature protection. The power
MOSFET operating temperature can be monitored with an
external negative temperature coefficient (NTC) thermistor
mounted next to the external MOSFET which is expected
to run the hottest–– often the high-side device, Q1. Elec­trically, the thermistor should form a voltage divider with
another resistor, R1, connected to VCC. Their midpoint
should be connected to OUTEN (see Figure 6). As the
temperature increases, the OUTEN pin voltage is reduced.
Under normal operating conditions, the OUTEN pin should
stay above 2V. All circuits will function normally, and the
OT pin will remain in a high state. If the temperature gets
abnormally high, the OUTEN pin voltage will eventually
drop below 2V. OT will switch to a logic low, providing an
over-temperature warning to the system. As OUTEN drops
below 1.7V, the LTC1553L disables both FET drivers. If
OUTEN is less than 1.2V, the LTC1553L will enter shut­down mode. To activate any of these three modes, the
OUTEN voltage must drop below the respective threshold
for longer than 30µs.

The internal oscillator can be synchronized to an external
clock by applying the external clocking signal to the
OUTEN pin. The synchronizing range extends from the
initial operating frequency up to 500kHz. If the external
frequency is much higher than the natural free-running
frequency, the peak-to-peak sawtooth amplitude within
the LTC1553L will decrease. Since the loop gain is in­versely proportional to the amplitude of the sawtooth, the
compensation network may need to be adjusted slightly.
Note that the temperature sensing circuitry does not
operate when external synchronization is used.

MOSFET Gate Drive

Power for the internal MOSFET drivers is supplied by
PVCC. This supply must be above the input supply voltage
by at least one power MOSFET V
opera

tion. This higher voltage can be supplied with a

GS(ON)

for efficient

separate supply, or it can be generated using a simple
charge pump as shown in Figure 7. The 85% typical
maximum duty cycle ensures sufficient off-time to refresh
the charge pump during each cycle.

12

LTC1553L

R

P

DC Q I

VP

VI

R

P

DC Q I

VP

VV I

DS ON Q

MAX Q

MAX

IN MAX Q

OUT MAX

DS ON Q

MAX Q

MAX

IN MAX Q

IN OUT MAX

()

()

()

()

()

()

=

()

[]

()

=

()











()()

=

()

[]

()

=

()











−

()()

1

1

2

1

2

2

2

2

2

2

1

2

U

WUU

APPLICATIONS INFORMATION

V

0.1µF

IN

+

C

IN

Q1

L

O

Q2

V

OUT

+

C

OUT

1553L F07

CC

OPTIONAL FOR V

1N5243B
13V

LTC1553L

If the OUTEN pin is low, G1 and G2 are both held low to
prevent output voltage undershoot. As VCC and PV
power up from a 0V condition, an internal undervoltage
lockup circuit prevents G1 and G2 from going high until
VCC reaches about 3.5V. If VCC powers up while PVCC is at
ground potential, the SS is forced to ground potential
internally. SS clamps the COMP pin low and prevents the
drivers from turning on. On power-up or recovery from
thermal shutdown, the drivers are designed such that G2
is held low until G1 first goes high.

> 5V

IN

PV

2

CC

Figure 7. Doubling Charge Pump

1N5817

G1

20

G2

1

P

should be calculated based primarily on required

MAX

efficiency or allowable thermal dissipation. A typical high
efficiency circuit designed for Pentium II with a 5V input
and a 2.8V, 11.2A output might allow no more than 4%
efficiency loss at full load for each MOSFET. Assuming
roughly 90% efficiency at this current level, this gives a
P

value of:

MAX

[(2.8)(11.2A/0.9)(0.04)] = 1.39W per FET

and a required R

R

DS ON Q

()

=

1

of:

DS(ON)

VW

5139

.

()( )

VA

2 8 11 2

..

()( )

=

0 019

.

2

Ω

Power MOSFETs

Two N-channel power MOSFETs are required for most
LTC1553L circuits. Logic level MOSFETs should be used
and they should be selected based on on-resistance con­siderations. R
output voltage, allowable power dissipation and maxi­mum required output current. In a typical LTC1553L buck
converter circuit the average inductor current is equal to
the output load current. This current is always flowing
through either Q1 or Q2 with the power dissipation split up
according to the duty cycle:

DC Q

()

DC Q

()

The R

DS(ON)

be calculated by rearranging the relation P = I2R.

V

1

=

=− =

21

required for a given conduction loss can now

should be chosen based on input and

DS(ON)

OUT

V

IN

−

VV

()

V

OUT

V

IN

IN OUT

V

IN

VW

5139

R

DS ON Q

()

Note also that while the required R
large MOSFETs, the dissipation numbers are only 1.39W
per device or less––large TO-220 packages and heat sinks
are not necessarily required in high efficiency applica­tions. Siliconix Si4410DY or International Rectifier IRF7413
(both in SO-8) or Siliconix SUD50N03 or Motorola
MTD20N03HDL (both in D PAK) are small footprint sur­face mount devices with R
of gate drive that work well in LTC1553L circuits. With
higher output voltages, the R
significantly lower than that for Q2. These conditions can
often be met by paralleling two MOSFETs for Q1 and using
a single device for Q2. Note that using a higher P
in the R
cost and circuit efficiency while increasing MOSFET heat
sink requirements.

DS(ON)

=

2

VV A

528112

()()

calculations will generally decrease MOSFET

()( )

.

−

..

DS(ON)

DS(ON)

=

0 025

.

2

DS(ON)

values below 0.03Ω at 5V

of Q1 may need to be

Ω

values suggest

value

MAX

13

LTC1553L

U

WUU

APPLICATIONS INFORMATION

Table 5. Recommended MOSFETs for LTC1553L Applications

TYPICAL INPUT

R

PARTS AT 25°C (mΩ) RATED CURRENT (A) C

Siliconix SUD50N03-10 19 15 at 25°C 3200 1.8 175
TO-252 10 at 100°C

Siliconix Si4410DY 20 10 at 25°C 2700 — 150
SO-8 8 at 75°C

Motorola MTD20N03HDL 35 20 at 25°C 880 1.67 150
D PAK 16 at 100°C

SGS-Thomson STD20N03L 23 20 at 25°C 2300 2.5 175
D PAK 14 at 100°C

Motorola MTB75N03HDL 7.5 75 at 25°C 4025 1.0 150
DD PAK 59 at 100°C

IRF IRL3103S 14 56 at 25°C 1600 1.8 175
DD PAK 40 at 100°C

IRF IRLZ44 28 50 at 25°C 3300 1.0 175
TO-220 36 at 100°C

Fuji 2SK1388 37 35 at 25°C 1750 2.08 150
TO-220

DS(ON)

CAPACITANCE

(pF) θJC (°C/W) T

ISS

JMAX

(°C)

Note: Please refer to the manufacturer’s data sheet for testing conditions

and detail information.

Inductor Selection

The inductor is often the largest component in the LTC1553L
design and should be chosen carefully. Inductor value and
type should be chosen based on output slew rate require­ments, output ripple requirements and expected peak
current. Inductor value is primarily controlled by the
required current slew rate. The maximum rate of rise of
current in the inductor is set by its value, the input-to­output voltage differential and the maximum duty cycle of
the LTC1553L. In a typical 5V input, 2.8V output applica­tion, the maximum current slew rate will be:

VV

−

()

DC

MAX

IN OUT

183.

=

LL

A

s

µ

where L is the inductor value in µ H. With proper frequency
compensation, the combination of the inductor and output
capacitor will determine the transient recovery time. In
general, a smaller value inductor will improve transient
response at the expense of increased output ripple voltage
and inductor core saturation rating. A 2µ H inductor would
have a 0.9A/µs rise time in this application, resulting in a

5.5µs delay in responding to a 5A load current step. During

this 5.5µ s, the difference between the inductor current and
the output current must be made up by the output capaci­tor, causing a temporary voltage droop at the output. To
minimize this effect, the inductor value should usually be
in the 1µH to 5µH range for most typical 5V input LTC1553L
circuits. To optimize performance, different combinations
of input and output voltages and expected loads may
require different inductor values.

Once the required value is known, the inductor core type
can be chosen based on peak current and efficiency
requirements. Peak current in the inductor will be equal to
the maximum output load current plus half of the peak-to­peak inductor ripple current. Ripple current is set by the
inductor value, the input and output voltage and the
operating frequency. The ripple current is approximately
equal to:

VV V

−

()()

I

RIPPLE

f

= LTC1553L oscillator frequency = 300kHz

OSC

IN OUT OUT

=

fLV

()()()

OSC O IN

LO = Inductor value

14

LTC1553L

U

WUU

APPLICATIONS INFORMATION

Solving this equation with our typical 5V to 2.8V applica­tion with a 2µH inductor, we get:

22 056

..

()( )

kHz HAµ

300 2

()()

Peak inductor current at 11.2A load:

11 2

The ripple current should generally be between 10% and
40% of the output current. The inductor must be able to
withstand this peak current without saturating, and the
copper resistance in the winding should be kept as low as
possible to minimize resistive power loss. Note that in
circuits not employing the current limit function, the
current in the inductor may rise above this maximum
under short circuit or fault conditions; the inductor should
be sized accordingly to withstand this additional current.
Inductors with gradual saturation characteristics are often
the best choice.

Input and Output Capacitors

A typical LTC1553L design puts significant demands on
both the input and the output capacitors. During constant
load operation, a buck converter like the LTC1553L draws
square waves of current from the input supply at the
switching frequency. The peak current value is equal to the
output load current plus 1/2 peak-to-peak ripple current,
and the minimum value is zero. Most of this current is
supplied by the input bypass capacitor. The resulting RMS
current flow in the input capacitor will heat it up, causing
premature capacitor failure in extreme cases. Maximum
RMS current occurs with 50% PWM duty cycle, giving an
RMS current value equal to I
capacitor with an adequate ripple current rating must be
used to ensure reliable operation.

Note that capacitor manufacturers’ ripple current ratings
are often based on only 2000 hours (three months)
lifetime at rated temperature. Further derating of the input
capacitor ripple current beyond the manufacturer’s speci­fication is recommended to extend the useful life of the
circuit. Lower operating temperature will have the largest
effect on capacitor longevity.

2

2

=

2

P-P

A

12 2..A

A+=

/2. A low ESR input

OUT

The output capacitor in a buck converter sees much less
ripple current under steady-state conditions than the input
capacitor. Peak-to-peak current is equal to that in the
inductor, usually 10% to 40% of the total load current.
Output capacitor duty places a premium not on power
dissipation but on ESR. During an output load transient,
the output capacitor must supply all of the additional load
current demanded by the load until the LTC1553L can
adjust the inductor current to the new value. Output
capacitor ESR results in a step in the output voltage equal
to the ESR value multiplied by the change in load current.
An 11A load step with a 0.05Ω ESR output capacitor will
result in a 550mV output voltage shift; this is 19.6% of the
output voltage for a 2.8V supply! Because of the strong
relationship between output capacitor ESR and output
load transient response, the output capacitor is usually
chosen for ESR, not for capacitance value; a capacitor with
suitable ESR will usually have a larger capacitance value
than is needed for energy storage.

Electrolytic capacitors rated for use in switching power
supplies with specified ripple current ratings and ESR can
be used effectively in LTC1553L applications. OS-CON
electrolytic capacitors from SANYO and other manufac­turers give excellent performance and have a very high
performance/size ratio for electrolytic capacitors. Surface
mount applications can use either electrolytic or dry
tantalum capacitors. Tantalum capacitors must be surge
tested and specified for use in switching power supplies.
Low cost, generic tantalums are known to have very short
lives followed by explosive deaths in switching power
supply applications. AVX TPS series surface mount
devices are popular surge tested tantalum capacitors that
work well in LTC1553L applications.

A common way to lower ESR and raise ripple current
capability is to parallel several capacitors. A typical
LTC1553L application might exhibit 5A input ripple cur­rent. SANYO OS-CON part number 10SA220M (220µF/
10V) capacitors feature 2.3A allowable ripple current at
85°C; three in parallel at the input (to withstand the input
ripple current) will meet the above requirements. Simi­larly, AVX TPSE337M006R0100 (330µ F/6V) have a rated
maximum ESR of 0.1Ω; seven in parallel will lower the net
output capacitor ESR to 0.014Ω. For low cost application,
SANYO MV-GX series of capacitors can be used with
acceptable performance.

15

LTC1553L

U

WUU

APPLICATIONS INFORMATION

Feedback Loop Compensation

The LTC1553L voltage feedback loop is compensated at
the COMP pin, attached to the output node of the internal
gm error amplifier. The feedback loop can generally be
compensated properly with an RC + C network from COMP
to GND as shown in Figure 8a.

Loop stability is affected by the values of the inductor,
output capacitor, output capacitor ESR, error amplifier
transconductance and error amplifier compensation net­work. The inductor and the output capacitor create a
double pole at the frequency:

fLC =

2π√(L

The ESR of the output capacitor forms a zero at the
frequency:

f

=

ESR

1

)(C

O

1

2π(ESR)(C

OUT

OUT

)

)

LTC1553L

COMP

10

R

C

C

C

C1

Figure 8a. Compensation Pin Hook-Up

f

Z

ERR

fSW = LTC1553L SWITCHING 
FREQUENCY

= CLOSED-LOOP CROSSOVER 

f

CO

FREQUENCY

SENSE

6

–

+

DAC

1553L F08a

The compensation network at the error amplifier output is
to provide enough phase margin at the 0dB crossover
frequency for the overall closed-loop transfer function.
The zero and pole from the compensation network are:

fZ =

2π(R

1

)(CC)

C

and

fP =

2π(R

1

)(C1)

C

respectively.

Figure 8b shows the Bode plot of the overall transfer
function.

The compensation value used in this design is based on
the following criteria: fSW = 12fCO, fZ = fLC and fP = 5fCO. At
the closed-loop frequency fCO, the attenuation due the LC
filter and the input resistor divider is compensated by the
gain of the PWM modulator and the gain of the error
amplifier (g

)(RC). Although a mathematical approach

mERR

to frequency compensation can be used, the added
complication of input and/or output filters, unknown ca­pacitor ESR, and gross operating point changes with input
voltage, load current variations, all suggest a more prac­tical empirical method. This can be done by injecting a
transient current at the load and using an RC network box
to iterate toward the final compensation values, or by
obtaining the optimum loop response using a network
analyzer to find the actual loop poles and zeros.

LOOP GAIN

f

f

ESR

LC

Figure 8b. Bode Plot of the LTC1553L Overall Transfer Function

Table 6. Suggested Compensation Network for 5V Input
Application Using Multiple Paralleled 330µF AVX TPS Output
Capacitors

LO (µH) CO (µF) RC (kΩ)C

1 990 1.8 0.022 680
1 1980 3.6 0.01 330
1 4950 9.1 0.01 120

2.7 990 5.1 0.01 220

2.7 1980 10 0.01 120

2.7 4950 24 0.0047 47

5.6 990 10 0.01 120

5.6 1980 20 0.0047 56

5.6 4950 51 0.0036 22

f

CO

–20dB/DECADE

f

P

FREQUENCY

(µF) C1 (pF)

C

1553L F08b

16

LTC1553L

U

WUU

APPLICATIONS INFORMATION

Table 6 shows the suggested compensation components
for 5V input applications based on the inductor and output
capacitor values. The values were calculated using mul­tiple paralleled 330µF AVX TPS series surface mount
tantalum capacitors as the output capacitor. The optimum
component values might deviate from the suggested
values slightly because of board layout and operating
condition differences.

An alternate output capacitor is the Sanyo MV-GX series.
Using multiple parallel 1500µF Sanyo MV-GX capacitors
for the output capacitor, Table 7 shows the suggested
compensation component value for a 5V input application
based on the inductor and output capacitor values.

Table 7. Suggested Compensation Network for 5V Input
Application Using Multiple Paralleled 1500µF SANYO MV-GX
Output Capacitors

LO (µH) CO (µF) RC (kΩ)C

1 4500 4.3 0.022 270
1 6000 5.6 0.0047 220
1 9000 8.2 0.01 150

2.7 4500 11 0.01 100

2.7 6000 15 0.01 82

2.7 9000 22 0.01 56

5.6 4500 24 0.01 56

5.6 6000 30 0.0047 39

5.6 9000 47 0.0047 27

VID0 to VID4, PWRGD and FAULT

(µF) C1 (pF)

C

this happens, FAULT will be triggered. Once FAULT is
triggered, G1 and G2 will be forced low immediately and
the LTC1553L will remain in this state until VCC power
supply is recycled or OUTEN is toggled.

15%

V

OUT

5%

RATED V

OUT

–5%

t

PWRGD

FAULT

PWRBAD

t

PWRGD

Figure 9. PWRGD and FAULT

t

FAULT

1553L F09

LAYOUT CONSIDERATIONS

When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of the
LTC1553L. These items are also illustrated graphically in
the layout diagram of Figure 10. The thicker lines show the
high current paths. Note that at 10A current levels or
above, current density in the PC board itself is a serious
concern. Traces carrying high current should be as wide
as possible. For example, a PCB fabricated with 2oz
copper requires a minimum trace width of 0.15" to
carry 10A.

The digital inputs (VID0 to VID4) program the internal DAC
which in turn controls the output voltage. These digital
input controls are intended to be static and are not
designed for high speed switching. Forcing V

OUT

to step
from a high to a low voltage by changing the VIDn pins
quickly can cause FAULT to trip.

Figure 9 shows the relationship between the V

OUT

voltage,
PWRGD and FAULT. To prevent PWRGD from interrupting
the CPU unnecessarily, the LTC1553L has a built-in t

PWRBAD

delay to prevent noise at the SENSE pin from toggling
PWRGD. The internal time delay is designed to take about
500µ s for PWRGD to go low and 1ms for it to recover.
Once PWRGD goes low, the internal circuitry watches for
the output voltage to exceed 115% of the rated voltage. If

1. In general, layout should begin with the location of the
power devices. Be sure to orient the power circuitry so
that a clean power flow path is achieved. Conductor
widths should be maximized and lengths minimized.
After you are satisfied with the power path, the control
circuitry should be laid out. It is much easier to find
routes for the relatively small traces in the control
circuits than it is to find circuitous routes for high
current paths.

2. The GND and SGND pins should be shorted right at the
LTC1553L. This helps to minimize internal ground
disturbances in the LTC1553L and prevents differences
in ground potential from disrupting internal circuit
operation. This connection should then tie into the

17

LTC1553L

U

WUU

APPLICATIONS INFORMATION

ground plane at a single point, preferably at a fairly quiet
point in the circuit such as close to the output capaci­tors. This is not always practical, however, due to
physical constraints. Another reasonably good point to
make this connection is between the output capacitors
and the source connection of the low side FET Q2. Do
not tie this single point ground in the trace run between
the low side FET source and the input capacitor ground,
as this area of the ground plane will be very noisy.

3. The small signal resistors and capacitors for frequency
compensation and soft start should be located very
close to their respective pins and the ground ends
connected to the signal ground pin through a separate
trace. Do not connect these parts to the ground plane!

4. The VCC and PVCC decoupling capacitors should be as
close to the LTC1553L as possible. The 10µF bypass

capacitors shown at VCC and PVCC will help provide
optimum regulation performance.

5. The (+) plate of CIN should be connected as close as
possible to the drain of the upper MOSFET. An addi­tional 1µF ceramic capacitor between VIN and power
ground is recommended.

6. The SENSE pin is very sensitive to pickup from the
switching node. Care should be taken to isolate SENSE
from possible capacitive coupling to the inductor switch­ing signal. A 0.1µ F is required between the SENSE pin
and the SGND pin next to the LTC1553L.

7. OUTEN is a high impedance input and should be
externally pulled up to a logic HIGH for normal
operation.

8. Kelvin sense I

and IFB at Q1 drain and source pins.

MAX

V

IN

+

C

IN

L

V

OUT

O

+

C

OUT

BOLD LINES INDICATE
HIGH CURRENT PATHS

Q1

1

LTC1553L

PV

CC

+

10µF

Q2

+

10µF

R

IMAX

C

SS

0.1µF

0.1µF

R

IFB

R

C

C1

C

G2

2



PV

CC

3

GND


SGND

4

5



V

CC

6

SENSE

7



I

MAX

8

IFB

9

SS

10

COMP



0.1µF

C

G1

OUTEN

VID0

VID1

VID2

VID3

VID4

PWRGD

FAULT

OT

20

19

18

VID0

17

VID1

VID2

VID3

VID4

5.6k

5.6k

5.6k

1153L F10

16

15

14

13

12

11



18

Figure 10. LTC1553L Layout Diagram

LTC1553L

U

WUU

APPLICATIONS INFORMATION

0.1µF

C1
150pF

5.6k5.6k

R

C

8.2k
CC

0.01µF

PWRGD
FAULT
OT
VID0 TO VID4
OUTEN
COMP



C

0.1µF

V



SS

PENTIUM II

SYSTEM

DALE

NTHS-1206N02

MOUNT THERMISTER

IN CLOSE THERMAL

PROXIMITY TO Q1

5.6k

5

5V

1.8k

Figure 11. Single Supply LTC1553L 5V to 1.8V-3.5V Application with Thermal Monitor

+

10µF

CC

LTC1553L

SGND SENSE

SS

I

MAX

GND

2.7k

V

IN

5V

+

CIN**

1N5817

PV

CC

G1

I

FB

G2

0.1µF

0.1µF

Q1*

20Ω



Q2*



 *SILICONIX SUD50N03-10
**SANYO 10MV1200GX



†

COILTRONICS CTX02-13198 OR

 PANASONIC 12TS-2R5SP

 ††

1200µF
× 4

L

O†

2µH
18A

††

C



+

OUT

330µF

× 7

AVX TPSE337M006R0100

v

OUT

1553L F11

PACKAGE DESCRIPTION

0.205 – 0.212**
(5.20 – 5.38)

0.005 – 0.009
(0.13 – 0.22)

*

DIMENSIONS DO NOT INCLUDE MOLD FLASH. MOLD FLASH 


SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE

**

DIMENSIONS DO NOT INCLUDE INTERLEAD FLASH. INTERLEAD 
FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE



0.022 – 0.037
(0.55 – 0.95)

Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen­tation that the interconnection of its circuits as described herein will not infringe on existing patent rights.

U

Dimension in inches (millimeters) unless otherwise noted.

G Package

20-Lead Plastic SSOP (0.209)

(LTC DWG # 05-08-1640)

0.278 – 0.289*
(7.07 – 7.33)



1718 14 13 12 1115161920

12345678910

0° – 8°

0.0256
(0.65)

BSC

0.010 – 0.015
(0.25 – 0.38)

0.301 – 0.311
(7.65 – 7.90)

0.068 – 0.078
(1.73 – 1.99)

0.002 – 0.008
(0.05 – 0.21)

G20 SSOP 0595

19

LTC1553L

PACKAGE DESCRIPTION

U

Dimension in inches (millimeters) unless otherwise noted.

SW Package

20-Lead Plastic Small Outline (Wide 0.300)

(LTC DWG # 05-08-1620)

0.496 – 0.512*

(12.598 – 13.005)

19 18

20

16

17

14 13

15

1112

(0.254 – 0.737)

0.009 – 0.013

(0.229 – 0.330)

NOTE:

1. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS.
THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS

DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE

*

DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE

**




RELATED PARTS

0.291 – 0.299**
(7.391 – 7.595)

0.010 – 0.029

NOTE 1

0.016 – 0.050

(0.406 – 1.270)

× 45°

NOTE 1

0° – 8° TYP

0.093 – 0.104

(2.362 – 2.642)

0.050

(1.270)

TYP

2345678

1

0.014 – 0.019

(0.356 – 0.482)

TYP

0.394 – 0.419

(10.007 – 10.643)

910

0.037 – 0.045

(0.940 – 1.143)

0.004 – 0.012

(0.102 – 0.305)

S20 (WIDE) 0396

PART NUMBER DESCRIPTION COMMENTS

LTC1142 Current Mode Dual Step-Down Switching Regulator Controller Dual Version of LTC1148
LTC1148 Current Mode Step-Down Switching Regulator Controller Synchronous, VIN ≤ 20V
LTC1149 Current Mode Step-Down Switching Regulator Controller Synchronous, VIN ≤ 48V, for Standard Threshold FETs
LTC1159 Current Mode Step-Down Switching Regulator Controller Synchronous, VIN ≤ 40V, for Logic Threshold FETs
LTC1266 Current Mode Step-Up/Down Switching Regulator Controller Synchronous N- or P-Channel FETs, Comparator/Low-Battery Detector
LTC1430 High Power Step-Down Switching Regulator Controller Synchronous N-Channel FETs, Voltage Mode
LTC1435 High Efficiency Low Noise Synchronous Step-Down Drive Synchronous N-Channel, VIN ≤ 36V

Switching Regulator

LTC1438 Dual High Efficiency Low Noise Synchronous Step-Down Dual LTC1435 with Power-On Reset

Switching Regulator

LTC1553 5-Bit Programmable Synchronous Switching Regulator High Voltage Version of LTC1553L

Controller for Pentium II Processor

1553lf LT/TP 0198 4K • PRINTED IN USA

 LINEAR TECHNOLOGY CORPORATION 1998

20

Linear Technology Corporation

1630 McCarthy Blvd., Milpitas, CA 95035-7417 ● [phone]
FAX: [phone]

●

TELEX: 499-3977 ● www.linear-tech.com