Datasheet LMV1012TPX-15, LMV1012TPX-07, LMV1012TP-15, LMV1012UP-15, LMV1012TPX-25 Datasheet (NSC)

May 2003

LMV1012-07/ LMV1012-15/ LMV1012-25
Analog Pre-Amplified IC’s for High Gain Microphones

LMV1012-07/ LMV1012-15/ LMV1012-25 Analog Amplifier IC for High Gain Microphones

General Description

The LMV1012 is an audio amplifier series for small form
factor electret microphones. It is designed to replace the
JFET amplifier currently being used. The LMV1012 series is
ideally suited for applications requiring high signal integrity in
the presence of ambient or RF noise, such as in cellular
communications. The LMV1012 audio amplifiers are guaran­teed to operate over a 2.2V to 5.0V supply voltage range
with fixed gains of 7.8dB, 15.6dB and 23.8dB. The devices
offer excellent gain accuracy and temperature stability as
compared to a JFET microphone.

The LMV1012 series enables a two-pin electret microphone
solution, which provides direct pin-to-pin compatibility with
the existing JFET market.

The devices are offered in two space saving 4-bump micro

™

SMD
and LMV1012TP-25 are well suited for canister packages

1.8mm and thicker. The LMV1012UP-15 is ideal for canisters

1.3mm and thicker. These miniature packages are designed
for electret condenser microphones (ECM) form factor.

packages. The LMV1012TP-07, LMV1012TP-15,

Features

(Typical LMV1012-15, 2.2V supply, RL= 2.2kΩ, C = 2.2µF,

= 18mVPP, unless otherwise specified)

V

IN

n Supply voltage 2V - 5V
n Supply current
n Signal to noise ratio (A-weighted) 60dB
n Output voltage noise (A-weighted) −89dBV
n Total Harmonic Distortion 0.09%
n Voltage gain

— LMV1012-07 7.8dB
— LMV1012-15 15.6dB
— LMV1012-25 23.8dB

n Temperature range −40˚C to 85˚C
n Offered in 4-bump micro SMD packages:

— 0.93 x 1.0 x 0.4mm
— 0.93 x 1.0 x 0.5mm

<

180µA

Applications

n Cellular phones
n Headsets
n Mobile communications
n Automotive accessories
n PDAs
n Accessory microphone products

Schematic Diagram

Built-In Gain Electret Microphone

20072302

20072301

© 2003 National Semiconductor Corporation DS200723 www.national.com

Physical Dimensions inches (millimeters)

unless otherwise noted

LMV1012-07/ LMV1012-15/ LMV1012-25

NOTE: UNLESS OTHERWISE SPECIFIED.

1. EPOXY COATING.

2. 63Sn/37Pb EUTECTIC BUMP.

3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD.

4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION PINS ARE NUMBERED COUNTERCLOCKWISE.

5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS
PACKAGE HEIGHT.

6. REFERENCE JEDEC REGISTRATION MO-211. VARIATION BC.

4-Bump Thin micro SMD

NS Package Number TPA04GKA

= 0.93mm X2= 1.006mm X3= 0.500mm

X

1

www.national.com 2

Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

LMV1012-07/ LMV1012-15/ LMV1012-25 Analog Amplifier IC for High Gain Microphones

NOTE: UNLESS OTHERWISE SPECIFIED.

1. TITANIUM COATING.

2. FOR SOLDER BUMP COMPOSITION, SEE "SOLDER INFORMATION" IN THE PACKAGING SECTION OF THE NATIONAL SEMICONDUCTOR WEB
PAGE (www.national.com).

3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD.

4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION.

5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS
PACKAGE HEIGHT.

6. REFERENCE JEDEC REGISTRATION MO-211. VARIATION CA.

4-Bump ULTRA-Thin micro SMD

NS Package Number UPA04GKA

= 0.93mm X2= 1.006mm X3= 0.400mm

X

1

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:

1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the

2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.

labeling, can be reasonably expected to result in a
significant injury to the user.

National Semiconductor
Americas Customer
Support Center

Email: [e-mail]
Tel: [phone]

www.national.com

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.

National Semiconductor
Europe Customer Support Center

Fax: [phone]

Email: [e-mail]
Deutsch Tel: [phone]
English Tel: [phone]
Français Tel: [phone]

National Semiconductor
Asia Pacific Customer
Support Center

Email: [e-mail]

National Semiconductor
Japan Customer Support Center

Fax: [phone]
Email: [e-mail]
Tel: [phone]