Datasheet LM4820IBP-6, LM4820MX-6, LM4820MM-6, LM4820IBPX-6 Datasheet (NSC)

LM4820-6

Fixed Gain 1 Watt Audio Power Amplifier

General Description

The LM4820-6 is an audio power amplifier primarily de­signed for demanding applications in mobile phones and
other portable communication device applications. It is ca­pable of delivering 1 watt of continuous average power to an
8Ω BTL load with less than 1% distortion (THD+N) at 6dB of
BTL gain from a 5V

DC

power supply.

Boomer audio poweramplifiersweredesigned specifically to
provide high quality output power with a minimal amount of
external components. The LM4820-6 does not require input
and gain resistors, output coupling capacitors or bootstrap
capacitors, and therefore is ideally suited for mobile phone
and other low voltage applications where minimal parts
count and low power consumption is a primary requirement.

The LM4820-6 features a low-power consumption shutdown
mode, which is achieved by driving the shutdown pin with
logic low. Additionally, the LM4820-6 features an internal
thermal shutdown protection mechanism.

The LM4820-6 contains advanced pop & click circuitry which
eliminates noises which would otherwise occur during
turn-on and turn-off transitions.

Key Specifications

j

Improved PSRR at 217Hz 62dB

j

Power Output at 5.0V & 1% THD 1.0W(typ.)

j

Power Output at 3.3V & 1% THD 400mW(typ.)

j

Shutdown Current 0.1µA(typ.)

Features

n Fixed 6dB BTL voltage gain
n Available in space-saving packages micro SMD, MSOP

and SOIC

n Ultra low current shutdown mode
n Can drive capacitive loads up to 500 pF
n Improved pop & click circuitry eliminates noises during

turn-on and turn-off transitions

n 2.0 - 5.5V operation
n No output coupling capacitors, snubber networks or

bootstrap capacitors required

n External gain configuration still possible

Applications

n Mobile Phones
n PDAs
n Portable electronic devices

Typical Application

Boomer®is a registered trademark of National Semiconductor Corporation.

DS200106-1

FIGURE 1. Typical Audio Amplifier Application Circuit

April 2002

LM4820-6 Fixed Gain 1 Watt Audio Power Amplifier

© 2002 National Semiconductor Corporation DS200106 www.national.com

Connection Diagram

8 Bump micro SMD

DS200106-23

Top View

Order Number LM4820IBP-6, LM4820IBPX-6

See NS Package Number BPA08DDB

Small Outline (SO) Package

DS200106-35

Top View

Order Number LM4820M-6

See NS Package Number M08A

Mini Small Outline (MSOP) Package

DS200106-36

Top View

Order Number LM4820MM-6

See NS Package Number MUA08A

micro SMD Marking

DS200106-70

Top View

X - Date Code
T - Die Traceability
G - Boomer Family

F - LM4820IBP-6

SO Marking

DS200106-72

Top View

XY - Date Code

TT - Die Traceability

Bottom 2 lines - Part Number ( LM4820M-6 )

MSOP Marking

DS200106-71

Top View

G- Boomer Family

26 - LM4820MM-6

LM4820-6

www.national.com 2

Absolute Maximum Ratings (Note 2)

If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.

Supply Voltage 6.0V
Storage Temperature −65˚C to +150˚C
Input Voltage −0.3V to V

DD

+0.3V
Power Dissipation (Note 3) Internally Limited
ESD Susceptibility (Note 4) 2500V
ESD Susceptibility (Note 5) 250V
Junction Temperature 150˚C
Thermal Resistance

θ

JC

(SO) 35˚C/W

θ

JA

(SO) 150˚C/W

θ

JA

(micro SMD) 220˚C/W

θ

JC

(MSOP) 56˚C/W

θ

JA

(MSOP) 190˚C/W
Soldering Information
See AN-1112 ’microSMD Wafers Level Chip Scale

Package’.

Operating Ratings

Temperature Range

T

MIN

≤ TA≤ T

MAX

−40˚C ≤ TA≤ 85˚C

Supply Voltage 2.0V ≤ V

DD

≤ 5.5V

Electrical Characteristics VDD=5V(Notes 1, 2, 8)

The following specifications apply for V

DD

= 5V, AV= 1, and 8Ω load unless otherwise specified. Limits apply for TA= 25˚C.

Symbol Parameter Conditions

LM4820-6

UnitsTypical Limit

(Note 6) (Note 7)

I

DD

Quiescent Power Supply Current VIN= 0V, Io= 0A 4 10 mA (max)

I

SD

Shutdown Current V

shutdown

= GND 0.1 µA (max)

P

o

Output Power THD = 2% (max);f=1kHz 1 W

THD+N Total Harmonic Distortion+Noise P

o

= 0.4 Wrms; f = 1kHz 0.1 %

PSRR Power Supply Rejection Ratio V

ripple

= 200mV sine p-p 62 (f =

217Hz)

66 (f =

1kHz)

dB

A

V

Fixed Voltage Gain 1.41Vinrms, RL=8Ω 6.0 6.5

5.5

dB Max

dB Min

Electrical Characteristics VDD= 3.3V (Notes 1, 2, 8)

The following specifications apply for V

DD

= 3.3V, AV= 1, and 8Ω load unless otherwise specified. Limits apply for TA= 25˚C.

Symbol Parameter Conditions

LM4820-6

UnitsTypical Limit

(Note 6) (Note 7)

I

DD

Quiescent Power Supply Current VIN= 0V, Io= 0A 3.5 mA (max)

I

SD

Shutdown Current V

shutdown

= GND 0.1 µA (max)

P

o

Output Power THD = 1% (max); f = 1kHz 0.4 W

THD+N Total Harmonic Distortion+Noise P

o

= 0.15Wrms; f = 1kHz 0.1 %

PSRR Power Supply Rejection Ratio V

ripple

= 200mV sine p-p 60 (f =

217Hz)

62 (f =

1kHz)

dB

A

V

Fixed Voltage Gain .7Vinrms, RL=8Ω 6.0 dB

LM4820-6

www.national.com3

Electrical Characteristics VDD= 2.6V (Notes 1, 2, 8)

The following specifications apply for V

DD

= 2.6V and 8Ω Load unless otherwise specified. Limits apply for TA= 25˚C.

Symbol Parameter Conditions

LM4820-6

UnitsTypical Limit

(Note 6) (Note 7)

I

DD

Quiescent Power Supply Current VIN= 0V, Io= 0A 2.6 mA (max)

I

SD

Shutdown Current V

shutdown

= GND 0.1 µA (max)

P

0

Output Power ( 8Ω )
Output Power ( 4Ω )

THD = 1% (max);f=1kHzTHD
= 1% (max);f=1kHz

0.2

0.4

W
W

THD+N Total Harmonic Distortion+Noise P

o

= 0.1Wrms; f = 1kHz 0.08 %

PSRR Power Supply Rejection Ratio V

ripple

= 200mV sine p-p 44 (f =

217Hz)

44 (f =

1kHz)

dB

A

V

Fixed Voltage Gain .5Vinrms, RL=8Ω 6.0 dB

Note 1: All voltages are measured with respect to the ground pin, unless otherwise specified.
Note 2:

Absolute Maximum Ratings

indicate limits beyond which damage to the device may occur.

Operating Ratings

indicate conditions for which the device is

functional, but do not guarantee specific performance limits.

Electrical Characteristics

state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.

Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by T

JMAX

, θJA, and the ambient temperature TA. The maximum

allowable power dissipation is P

DMAX

=(T

JMAX–TA

)/θJAor the number given in Absolute Maximum Ratings, whichever is lower. For the LM4820-6, see power

derating curves for additional information.

Note 4: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
Note 5: Machine Model, 220 pF–240 pF discharged through all pins.
Note 6: Typicals are measured at 25˚C and represent the parametric norm.
Note 7: Limits are guaranteed to National’s AOQL (Average Outgoing Quality Level).
Note 8: For micro SMD only, shutdown current is measured in a Normal Room Environment. Exposure to direct sunlight will increase I

SD

by a maximum of 2µA.

External Components Description (

Figure 1

)

Components Functional Description

2. C

i

Input coupling capacitor which blocks the DC voltage at the amplifiers input terminals. Also creates a
highpass filter with R

i

at fc= 1/(2π RiCi). Refer to the section, Proper Selection of External Components,

for an explanation of how to determine the value of C

i

.

4. C

S

Supply bypass capacitor which provides power supply filtering. Refer to the Power Supply Bypassing
section for information concerning proper placement and selection of the supply bypass capacitor.

5. C

B

Bypass pin capacitor which provides half-supply filtering. Refer to the section, Proper Selection of External
Components, for information concerning proper placement and selection of C

B

.

Typical Performance Characteristics

THD+N vs Frequency
at V

DD

=5V,8ΩRL, and PWR = 250mW

DS200106-37

THD+N vs Frequency
at V

DD

= 3.3V, 8Ω RL, and PWR = 150mW

DS200106-38

LM4820-6

www.national.com 4

Typical Performance Characteristics (Continued)

THD+N vs Frequency
at V

DD

= 2.6V, 8Ω RL, and PWR = 100mW

DS200106-39

THD+N vs Frequency
at V

DD

= 2.6V, 4Ω RL, and PWR = 100mW

DS200106-40

THD+N vs Power Out

@

VDD=5V,8ΩRL, 1kHz

DS200106-41

THD+N vs Power Out

@

VDD= 3.3V, 8Ω RL, 1kHz

DS200106-42

THD+N vs Power Out

@

VDD= 2.6V, 8Ω RL, 1kHz

DS200106-43

THD+N vs Power Out

@

VDD= 2.6V, 4Ω RL, 1kHz

DS200106-44

LM4820-6

www.national.com5

Typical Performance Characteristics (Continued)

Power Supply Rejection Ratio (PSRR)

@

VDD=5V

DS200106-45

Input terminated with 10Ω R

Power Supply Rejection Ratio (PSRR)

@

VDD=5V

DS200106-73

Input Floating

Power Supply Rejection Ratio (PSRR)

@

VDD= 2.6V

DS200106-47

Input terminated with 10Ω R

Power Supply Rejection Ratio (PSRR)

@

VDD= 3.3V

DS200106-46

Input terminated with 10Ω R

Power Dissipation vs
Output Power
V

DD

= 3.3V

DS200106-49

Power Dissipation vs
Output Power

@

VDD=5V

DS200106-48

LM4820-6

www.national.com 6

Typical Performance Characteristics (Continued)

Output Power vs
Load Resistance

DS200106-51

Power Dissipation vs
Output Power
V

DD

= 2.6V

DS200106-50

Supply Current vs
Shutdown Voltage

DS200106-53

Clipping (Dropout) Voltage vs
Supply Voltage

DS200106-52

Open Loop Frequency Response

DS200106-55

Frequency Response vs
Input Capacitor Size

DS200106-54

LM4820-6

www.national.com7

Typical Performance Characteristics (Continued)

Power Derating Curves

DS200106-69

Noise Floor

DS200106-56

LM4820-6

www.national.com 8

Application Information

BRIDGE CONFIGURATION EXPLANATION

As shown in

Figure 1

, the LM4820-6 has two operational

amplifiers internally.

Figure 1

shows that the output of am­plifier one serves as the input to amplifier two which results
in both amplifiers producing signals identical in magnitude,
but out of phase by 180˚. Consequently, the differential gain
for the IC is

A

VD

= 2 *(Rf/Ri) (1)

By driving the load differentially through outputs Vo1 and
Vo2, an amplifier configuration commonly referred to as
“bridged mode” is established. Bridged mode operation is
different from the classical single-ended amplifier configura­tion where one side of the load is connected to ground.

A bridge amplifier design has a few distinct advantages over
the single-ended configuration, as it provides differential
drive to the load, thus doubling output swing for a specified
supply voltage. Four times the output power is possible as
compared to a single-ended amplifier under the same con­ditions. This increase in attainable output power assumes
that the amplifier is not current limited or clipped. In order to
choose an amplifier’s closed-loop gain without causing ex­cessive clipping, please refer to the Audio Power Amplifier
Design section.

A bridge configuration, such as the one used in LM4820-6,
also creates a second advantage over single-ended amplifi­ers. Since the differential outputs, Vo1 and Vo2, are biased
at half-supply,no net DC voltage exists across the load. This
eliminates the need for an output coupling capacitor which is
required in a single supply, single-ended amplifier configura­tion. Without an output coupling capacitor, the half-supply
bias across the load would result in both increased internal
IC power dissipation and also possible loudspeaker damage.

POWER DISSIPATION

Power dissipation is a major concern when designing a
successful amplifier, whether the amplifier is bridged or
single-ended. A direct consequence of the increased power
delivered to the load by a bridge amplifier is an increase in
internal power dissipation. Since the LM4820-6 has two
operational amplifiers in one package, the maximum internal
power dissipation is 4 times that of a single-ended amplifier.
The maximum power dissipation for a given application can
be derived from the power dissipation graphs or from Equa­tion 2.

P

DMAX

= 4*(VDD)2/(2π2RL) (2)

It is critical that the maximum junction temperature T

JMAX

of

150˚C is not exceeded. T

JMAX

can be determined from the

power derating curves by using P

DMAX

and the PC board foil
area. By adding additional copper foil, the thermal resistance
of the application can be reduced from a free air value of
150˚C/W, resulting in higher P

DMAX

. Additional copper foil
can be added to any of the leads, bumps or vias connected
to the LM4820-6. It is especially effective when connected to
V

DD,GND

, and the output pins. Refer to the application
information on the LM4820-6 reference design board for an
example of good heat sinking. If T

JMAX

still exceeds 150˚C,
then additional changes must be made. These changes can
include reduced supply voltage, higher load impedance, or
reduced ambient temperature. Internal power dissipation is a
function of output power. Refer to the Typical Performance
Characteristics curves for power dissipation information for
different output powers and output loading.

POWER SUPPLY BYPASSING

As with any amplifier, proper supply bypassing is critical for
low noise performance and high power supply rejection. The
capacitor location on both the bypass and power supply pins
should be as close to the device as possible. Typical appli­cations employ a 5V regulator with 10 µF tantalum or elec­trolytic capacitor and a ceramic bypass capacitor which aid
in supply stability. This does not eliminate the need for
bypassing the supply nodes of the LM4820-6. The selection
of a bypass capacitor, especially C

B

, is dependent upon
PSRR requirements, click and pop performance (as ex­plained in the section, Proper Selection of External Com-

ponents), system cost, and size constraints.

SHUTDOWN FUNCTION

In order to reduce power consumption while not in use, the
LM4820-6 contains a shutdown pin to externally turn off the
amplifier’s bias circuitry. This shutdown feature turns the
amplifier off when a logic low is placed on the shutdown pin.
By switching the shutdown pin to ground, the LM4820-6
supply current draw will be minimized in idle mode. While the
device will be disabled with shutdown pin voltages less than

0.5V

DC

, the idle current may be greater than the typical
value of 0.1µA. (Idle current is measured with the shutdown
pin grounded).

In many applications, a microcontroller or microprocessor
output is used to control the shutdown circuitry to provide a
quick, smooth transition into shutdown. Another solution is to
use a single-pole, single-throw switch in conjunction with an
external pull-up resistor. When the switch is closed, the
shutdown pin is connected to ground and disables the am­plifier. If the switch is open, then the external pull-up resistor
will enable the LM4820-6. This scheme guarantees that the
shutdown pin will not float thus preventing unwanted state
changes.

PROPER SELECTION OF EXTERNAL COMPONENTS

Proper selection of external components in applications us­ing integrated power amplifiers is critical to optimize device
and system performance. While the LM4820-6 is tolerant of
external component combinations, consideration to compo­nent values must be used to maximize overall system qual­ity.

The LM4820-6 is unity-gain stable which gives the designer
maximum system flexibility. The LM4820-6 at 6dB of fixed
gain is a low gain configuration which minimizes THD+N
values, and maximizes the signal to noise ratio. Low gain
configurations require large input signals to obtain a given
output power. Input signals equal to or greater than 1 Vrms
are available from sources such as audio codecs. Please
refer to the section, Audio Power Amplifier Design, for a
more complete explanation of proper gain selection.

Besides gain, one of the major considerations is the closed­loop bandwidth of the amplifier. To a large extent, the band­width is dictated by the choice of external components
shown in

Figure 1

. The input coupling capacitor, Ci, forms a
first order high pass filter which limits low frequency re­sponse. This value should be chosen based on needed
frequency response for a few distinct reasons.

Selection Of Input Capacitor Size

Large input capacitors are both expensive and space hungry
for portable designs. Clearly, a certain sized capacitor is
needed to couple in low frequencies without severe attenu­ation. But in many cases the speakers used in portable
systems, whether internal or external, have little ability to

LM4820-6

www.national.com9

Application Information (Continued)

reproduce signals below 100 Hz to 150 Hz. Thus, using a
large input capacitor may not increase actual system perfor­mance.

In addition to system cost and size, click and pop perfor­mance is effected by the size of the input coupling capacitor,
C

i.

A larger input coupling capacitor requires more charge to

reach its quiescent DC voltage (nominally 1/2 V

DD

). This
charge comes from the output via the feedback and is apt to
create pops upon device enable. Thus, by minimizing the
capacitor size based on necessary low frequency response,
turn-on pops can be minimized.

Besides minimizing the input capacitor size, careful consid­eration should be paid to the bypass capacitor value. Bypass
capacitor, C

B

, is the most critical component to minimize
turn-on pops since it determines how fast the LM4820-6
turns on. The slower the LM4820-6’s outputs ramp to their
quiescent DC voltage (nominally 1/2 V

DD

), the smaller the

turn-on pop. Choosing C

B

equal to 1.0 µF along with a small

value of C

i

(in the range of 0.1 µF to 0.39 µF), should
produce a virtually clickless and popless shutdown function.
While the device will function properly, (no oscillations or
motorboating), with C

B

equal to 0.1 µF, the device will be
much more susceptible to turn-on clicks and pops. Thus, a
value of C

B

equal to 1.0 µF is recommended in all but the

most cost sensitive designs.

AUDIO POWER AMPLIFIER DESIGN
A 1W/8Ω AUDIO AMPLIFIER

Given:

Power Output 1 Wrms
Load Impedance 8Ω
Input Level 1 Vrms
Input Impedance 25 kΩ
Bandwidth 100 Hz–20 kHz

±

0.25 dB

A designer must first determine the minimum supply rail to
obtain the specified output power. By extrapolating from the
Output Power vs Supply Voltage graphs in the Typical Per-
formance Characteristics section, the supply rail can be
easily found. A second way to determine the minimum sup­ply rail is to calculate the required V

opeak

using Equation 3.
Using this method, the minimum supply voltage would be
(V

opeak

+(V

OD

TOP

+V

OD

BOT

)), where V

OD

BOT

and V

OD

TOP

are
extrapolated from the Dropout Voltage vs Supply Voltage
curve in the Typical Performance Characteristics section.

(3)

2.7V

DD

to 5VDDis a standard supply voltage range for most
applications. Extra supply voltage creates headroom that
allows the LM4820-6 to reproduce peaks in excess of 1W
without producing audible distortion. At this time, the de­signer must make sure that the power supply choice along
with the output impedance does not violate the conditions
explained in the Power Dissipation section.

Once the power dissipation equations have been addressed,
the differential gain is determined from Equations 4 or 5.

(4)

or

A

VD

=2(Rf/Ri) (5)

R

f=Ri

= 25kΩ

A

VD

=2(25kΩ/25kΩ )

A

VD

=2

The last step in this design example is setting the amplifier’s

-3dB frequency bandwidth. To achieve the desired

±

0.25dB
pass band magnitude variation limit, the low frequency re­sponse must extend to at least one-fifth the lower bandwidth
limit. The high frequency response must extend to at least
five times the upper bandwidth limit. The gain variation for
both response limits is 0.17dB, well within the

±

0.25dB
desired limit. The results are

f

L

= 100Hz/5 = 20Hz

and

f

H

= 20kHzx5=100kHz

As mentioned in the Selecting Proper External Compo-
nents section, R

i

and Cicreate a highpass filter that sets the
amplifier’s lower bandpass frequency limit. To find the cou­pling capacitor’s value, use Equation 6

C

i

≥ 1/(2πRifL) (6)

The result is

1/(2π*25kΩ*20kHz) = .318µf
Use a 0.33µf capacitor, the closest standard value.
The product of the desired high frequency cutoff (100kHz in

this example ) and the differential gain A

VD

, determines the

upper passband response limit. With A

VD

= 2 and fH=
100kHz, the closed-loop gain bandwidth product (GBWP) is
200kHz. This is less than the LM4820-6’s 25MHz GBWP.
With this margin, the amplifier can be used in designs that
require more differential gain while avoiding performance,
restricting bandwidth limitations.

LM4820-6

www.national.com 10

Application Information (Continued)

REFERENCE DESIGN BOARD and LAYOUT - micro SMD

DS200106-25

Figure 4

LM4820-6

www.national.com11

Application Information (Continued)

LM4820-6 micro SMD BOARD ARTWORK

Silk Screen

DS200106-57

Top Layer

DS200106-58

Bottom Layer

DS200106-59

Inner Layer Ground

DS200106-60

Inner Layer V

DD

DS200106-61

LM4820-6

www.national.com 12

Application Information (Continued)

REFERENCE DESIGN BOARD and PCB LAYOUT GUIDE­LINES - MSOP & SO Boards

DS200106-68

Figure 5

LM4820-6

www.national.com13

Application Information (Continued)

LM4820-6 SO DEMO BOARD ARTWORK

Silk Screen

DS200106-62

Top Layer

DS200106-63

Bottom Layer

DS200106-64

LM4820-6 MSOP DEMO BOARD ARTWORK

Silk Screen

DS200106-65

Top Layer

DS200106-66

Bottom Layer

DS200106-67

LM4820-6

www.national.com 14

Application Information (Continued)
Mono LM4820-6 Reference Design Boards

Bill of Material for all 3 Demo Boards

Item Part Number Part Description Qty Ref Designator

1 551011208-001 LM4820-6 Mono Reference Design

Board

1

10 482911183-001 LM4820-6 Audio AMP 1 U1
20 151911207-001 Tant Cap 1uF 16V 10 1 C1
21 151911207-002 Cer Cap 0.39uF 50V Z5U 20% 1210 1 C2
25 152911207-001 Tant Cap 1uF 16V 10 1 C3
30 472911207-001 Res 20K Ohm 1/10W 5 3 R1
35 210007039-002 Jumper Header Vertical Mount 2X1

0.100

2J1

PCB LAYOUT GUIDELINES

This section provides practical guidelines for mixed signal
PCB layout that involves various digital/analog power and
ground traces. Designers should note that these are only
’rule-of-thumb’ recommendations and the actual results will
depend heavily on the final layout.

General Mixed Signal Layout Recommendation

Power and Ground Circuits

For 2 layer mixed signal design, it is important to isolate the
digital power and ground trace paths from the analog power
and ground trace paths. Star trace routing techniques (bring­ing individual traces back to a central point rather than daisy
chaining traces together in a serial manner) can have a
major impact on low level signal performance. Star trace
routing refers to using individual traces to feed power and
ground to each circuit or even device. This technique will
take require a greater amount of design time but will not
increase the final price of the board. The only extra parts
required will be some jumpers.

Single-Point Power / Ground Connections

The analog power traces should be connected to the digital
traces through a single point (link). A ’Pi-filter’ can be helpful
in minimizing High Frequency noise coupling between the
analog and digital sections. It is further recommended to put
digital and analog power traces over the corresponding digi­tal and analog ground traces to minimize noise coupling.

Placement of Digital and Analog Components

All digital components and high-speed digital signals traces
should be located as far away as possible from analog
components and circuit traces.

Avoiding Typical Design / Layout Problems

Avoid ground loops or running digital and analog traces
parallel to each other (side-by-side) on the same PCB layer.
When traces must cross over each other do it at 90 degrees.
Running digital and analog traces at 90 degrees to each
other from the top to the bottom side as much as possible will
minimize capacitive noise coupling and cross talk.

LM4820-6

www.national.com15

Physical Dimensions inches (millimeters) unless otherwise noted

Note: Unless otherwise specified.

1. Epoxy coating.

2. 63Sn/37Pb eutectic bump.

3. Recommend non-solder mask defined landing pad.

4. Pin 1 is established by lower left corner with respect to text orientation pins are numbered counterclockwise.

5. Reference JEDEC registration MO-211, variation BC.

8-Bump micro SMD

Order Number LM4820IBP-6, LM4820IBPX-6

NS Package Number BPA08DDB

X

1

= 1.361 X2= 1.361 X3= 0.850

LM4820-6

www.national.com 16

Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

MSOP

Order Number LM4820MM-6

NS Package Number MUA08A

LM4820-6

www.national.com17

Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:

1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.

2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.

National Semiconductor
Corporation

Americas
Email: [e-mail]

National Semiconductor
Europe

Fax: [phone]

Email: [e-mail]
Deutsch Tel: [phone]
English Tel: [phone]
Français Tel: [phone]

National Semiconductor
Asia Pacific Customer
Response Group

Tel: [phone]
Fax: [phone]
Email: [e-mail]

National Semiconductor
Japan Ltd.

Tel: [phone]
Fax: [phone]

www.national.com

SO

Order Number LM4820M-6

NS Package Number M08A

LM4820-6 Fixed Gain 1 Watt Audio Power Amplifier

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.