Datasheet LM3700XCBPX-290, LM3700XCBP-308, LM3700XCBP-290, LM3700XBBPX-270, LM3700XBBP-270 Datasheet (NSC)

LM3700/LM3701
Microprocessor Supervisory Circuit with Low Line
Output

General Description

The LM3700/LM3701 series of microprocessor supervisory
circuits provide the maximum flexibility for monitoring power
supplies and battery controlled functions in systems without
backup batteries. The LM3700/LM3701 series are available
in a 9-bump micro SMD package.

Built-in features include the following:
Reset: Reset is asserted during power-up, power-down, and

brownout conditions. RESET is guaranteed down to V

CC

of

1.0V.
Low Line Output: This early power failure warning indicator

goes low when the supply voltage drops to a value which is
2% higher than the reset threshold voltage.

Features

n Standard Reset Threshold voltage: 3.08V
n Custom Reset Threshold voltages: For other voltages

between 2.2V and 5.0V in 10mV increments, contact
National Semiconductor Corp.

n No external components required
n RESET (LM3700) or RESET (LM3701) outputs
n Precision supply voltage monitor
n Factory programmable Reset Timeout Delay
n Available in micro SMD package for minimum footprint

n

±

0.5% Reset threshold accuracy at room temperature

n

±

2% Reset threshold accuracy over temperature

extremes

n Reset assertion down to 1V V

CC

(RESET option only)

n 28 µA VCCsupply current

Applications

n Embedded Controllers and Processors
n Intelligent Instruments
n Automotive Systems
n Critical µP Power Monitoring

Typical Application

20011403

September 2003

LM3700/LM3701 Microprocessor Supervisory Circuit with Low Line Output

© 2003 National Semiconductor Corporation DS200114 www.national.com

Connection Diagram

Top View

(looking from the coating side)

micro SMD 9 Bump Package

BPA09

20011401

Pin Descriptions

Bump No. Name Function

B1 V

CC

Power Supply input.

C1 RESET

Reset Logic Output. Pulses low for tRP(Reset Timeout Period) when triggered, and stays
low whenever V

CC

is below the reset threshold or when MR is below V

MRT

. It remains low
for tRPafter either VCCrises above the reset threshold, or after MR input rises above
V

MRT

(LM3700 only).

RESET Reset Logic Output. RESET is the inverse of RESET (LM3701 only).

C3 LLO Low-Line Logic Output. Early Power-Fail warning output. Low when VCCfalls below V

LLOT

(Low-Line Output Threshold). This output can be used to generate an NMI (Non-Maskable
Interrupt) to provide an early warning of imminent power-failure.

B3 GND Ground reference for all signals.

A1, A2, A3,

C2

NC No Connect.

B2 NC No Connect. Test input used at factory only. Leave floating.

LM3700/LM3701

www.national.com 2

Block Diagram

20011405

LM3700/LM3701

www.national.com3

Ordering Information

20011404

*For other voltages between 2.2V and 5.0V, please contact National Semiconductor sales office.

LM3700/LM3701

Part Number Output

Reset

Timeout

Period

Package

Marking

LM3700XBBP-270 totem-pole 28ms %%IE

LM3700XBBPX-270 totem-pole 28ms %%IE

LM3700XCBP-290 totem-pole 200ms %%123

LM3700XCBPX-290 totem-pole 200ms %%123

LM3700XCBP-308 totem-pole 200ms %%I0

LM3700XCBPX-308 totem-pole 200ms %%I0

LM3701XCBP-308 totem-pole 200ms %%I1

LM3701XCBPX-308 totem-pole 200ms %%I1

LM3700XBBP-420 totem-pole 28ms %%IF

LM3700XBBPX-420 totem-pole 28ms %%IF

%% is the datecode and will vary with time.

Table Of Functions

Part

Number

Active

Low

Reset

Active

High

Reset

Output
(X = totem-pole)
(Y = open-drain)

Reset

Timeout

Period

Low
Line

Output

LM3700 x X, Y* Customized x

LM3701 x X Customized x

* = available upon request. Contact National

LM3700/LM3701

www.national.com 4

Absolute Maximum Ratings (Note 1)

If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.

Supply Voltage (V

CC

) −0.3V to 6.0V

All Other Inputs −0.3V to V

CC

+ 0.3V

ESD Ratings (Note 2)

Human Body Model
Machine Model

1.5kV
150V

Power Dissipation (Note 3)

Operating Ratings (Note 1)

Temperature Range −40˚C ≤ T

J

≤ 85˚C

LM3700/LM3701 Series Electrical Characteristics

Limits in the standard typeface are for TJ= 25˚C and limits in boldface type apply over full operating range. Unless otherwise
specified: V

CC

= +2.2V to 5.5V.

Symbol Parameter Conditions Min Typ Max Units

POWER SUPPLY

V

CC

Operating Voltage
Range: V

CC

LM3700 1.0 5.5

V

LM3701 1.2 5.5

I

CC

VCCSupply
Current

All inputs = VCC; all outputs floating 28 50 µA

RESET THRESHOLD

V

RST

Reset Threshold VCCfalling −0.5

−2

V

RST

+0.5

+2

%

V

CC

falling: TA= 0˚C to 70˚C −1.5 +1.5

V

RSTH

Reset Threshold
Hysteresis

0.0032•V

RST

mV

t

RP

Reset Timeout
Period

Reset Timeout Period = A
Reset Timeout Period = B
Reset Timeout Period = C
Reset Timeout Period = D

1

20

140

1120

1.4
28

200

1600

2

40

280

2240

ms

t

RD

VCCto Reset
Delay

VCCfalling at 1mV/µs 20 µs

RESET (LM3701)

V

OL

RESET V

CC

>

2.25V, I

SINK

= 900µA 0.3

VV

CC

>

2.7V, I

SINK

= 1.2mA 0.3

V

CC

>

4.5V, I

SINK

= 3.2mA 0.4

V

OH

RESET V

CC

>

1.2V, I

SOURCE

= 50µA 0.8 V

CC

V

V

CC

>

1.8V, I

SOURCE

= 150µA 0.8 V

CC

V

CC

>

2.25V, I

SOURCE

= 300µA 0.8 V

CC

V

CC

>

2.7V, I

SOURCE

= 500µA 0.8 V

CC

V

CC

>

4.5V, I

SOURCE

= 800µA VCC− 1.5V

I

LKG

Output Leakage
Current

V

RESET

= 5.5V 1.0 µA

RESET (LM3700)

V

OL

RESET V

CC

>

1.0V, I

SINK

= 50µA 0.3

V

V

CC

>

1.2V, I

SINK

= 100µA 0.3

V

CC

>

2.25V, I

SINK

= 900µA 0.3

V

CC

>

2.7V, I

SINK

= 1.2mA 0.3

V

CC

>

4.5V, I

SINK

= 3.2mA 0.4

V

OH

RESET V

CC

>

2.25V, I

SOURCE

= 300µA 0.8 V

CC

V

CC

>

2.7V, I

SOURCE

= 500µA 0.8 V

CC

V

CC

>

4.5V, I

SOURCE

= 800µA VCC− 1.5V

LM3700/LM3701

www.national.com5

LM3700/LM3701 Series Electrical Characteristics (Continued)

Limits in the standard typeface are for TJ= 25˚C and limits in boldface type apply over full operating range. Unless otherwise
specified: V

CC

= +2.2V to 5.5V.

Symbol Parameter Conditions Min Typ Max Units

LLO

V

OL

LLO Output
Voltage

V

CC

>

2.25V, I

SINK

= 900µA 0.3

V

V

CC

>

2.7V, I

SINK

= 1.2mA 0.3

V

CC

>

4.5V, I

SINK

= 3.2mA 0.4

V

OH

V

CC

>

2.25V, I

SOURCE

= 300µA 0.8 V

CC

V

CC

>

2.7V, I

SOURCE

= 500µA 0.8 V

CC

V

CC

>

4.5V, I

SOURCE

= 800µA VCC− 1.5V

LLO OUTPUT

V

LLOT

LLO Output
Threshold
(V

LLO−VRST,VCC

falling)

1.01

•

V

RST

1.02•V

RST

1.03•V

RST

V

V

LLOTH

Low-Line
Comparator
Hysteresis

0.0032

•

V

RST

mV

t

CD

Low-Line
Comparator Delay

VCCfalling at 1mV/µs 20 µs

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device
is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics.
The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the
listed conditions.

Note 2: The Human Body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. The machine model is a 200pF capacitor discharged
directly into each pin.

Note 3: The maximum allowable power dissipation is a function of the maximum junction temperature, T

J

(MAX), the junction-to-ambient thermal resistance, θ

J-A

,

and the ambient temperature, T

A

. The maximum allowable power dissipation at any ambient temperture is calculated using:

Where the value of θ

J-A

for the micro SMD package is 220˚C/W.

LM3700/LM3701

www.national.com 6

Typical Performance Characteristics

Supply Current vs Supply Voltage 3.3V Supply Current vs Temperature

20011415

20011411

Normalized Reset Threshold Voltage vs Temperature Reset Timeout Period vs V

CC

20011412

20011432

Reset Timeout Period vs Temperature

Max. Transient Duration vs Reset Comparator Overdrive

(VCC= 3.3V)

20011410

20011416

LM3700/LM3701

www.national.com7

Typical Performance Characteristics (Continued)

Low-Line Comparator Propagation Delay vs Temperature

20011414

LM3700/LM3701

www.national.com 8

Circuit Information

RESET OUTPUT

The Reset input of a µP initializes the device into a known
state. The LM3700/LM3701 microprocessor supervisory cir­cuits assert a forced reset output to prevent code execution
errors during power-up, power-down, and brownout condi­tions.

RESET is guaranteed valid for V

CC

>

1V. Once VCCex­ceeds the reset threshold, an internal timer maintains the
output for the reset timeout period. After this interval, reset
goes high. The LM3700 offers an active-low RESET; The
LM3701 offers an active-high RESET.

Any time V

CC

drops below the reset threshold (such as

during a brownout), the reset activates. When V

CC

again
rises above the reset threshold, the internal timer starts.
Reset holds until V

CC

exceeds the reset threshold for longer

than the reset timeout period. After this time, reset releases.

RESET THRESHOLD

The LM3700/LM3701 family is available with a reset voltage
of 3.08V. Other reset thresholds in the 2.20V to 5.0V range,
in steps of 10 mV, are available; contact National Semicon­ductor for details.

LOW-LINE OUTPUT (LLO)

The low-line output comparator is typically used to provide a
non-maskable interrupt to a µP when V

CC

begins falling. LLO

monitors VCCand goes low when VCCfalls below V

LLOT

(typically 1.02•V

RST

) with hysteresis of 0.0032•V

RST

.

SPECIAL PRECAUTIONS FOR THE MICRO SMD
PACKAGE

As with most integrated circuits, the LM3700 and LM3701
are sensitive to exposure from visible and infrared (IR) light
radiation. Unlike a plastic encapsulated IC, the micro SMD
package has very limited shielding from light, and some
sensitivity to light reflected from the surface of the PC board
or long wavelength IR entering the die from the side may be
experienced. This light could have an unpredictable affect on
the electrical performance of the IC. Care should be taken to
shield the device from direct exposure to bright visible or IR
light during operation.

MICRO SMD MOUNTING

The micro SMD package requires specific mounting tech­niques which are detailed in National Semiconductor Appli­cation Note AN-1112. Referring to the section Surface
Mount Technology (SMT) Assembly Considerations,it
should be noted that the pad style which must be used with
the 9-pin package is the NSMD (non-solder mask defined)
type.

For best results during assembly, alignment ordinals on the
PC board may be used to facilitate placement of the micro
SMD device.

LM3700/LM3701

www.national.com9

Timing Diagrams

20011428

FIGURE 1. LM3700 Reset Time

20011429

FIGURE 2. LLO Output

LM3700/LM3701

www.national.com 10

Typical Application Circuits

20011424

FIGURE 3. LM3701 Power-On Delay

LM3700/LM3701

www.national.com11

Typical Application Circuits (Continued)

20011422

FIGURE 4. Regulator/Switch with Long-Term Overvoltage Lockout Prevents Overdissipation in Linear Regulator

LM3700/LM3701

www.national.com 12

Physical Dimensions inches (millimeters)

unless otherwise noted

NOTES: UNLESS OTHERWISE SPECIFIED

1. EPOXY COATING

2. 63Sn/37Pb EUTECTIC BUMP

3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD.

4. PIN 1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION. REMAINING PINS ARE NUMBERED COUNTER
CLOCKWISE.

5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS
PACKAGE HEIGHT.

6.NO JEDEC REGISTRATION AS OF AUG.1999.

9 bump micro SMD Package

NS Package Number BPA09FFB

The dimensions of X1, X2 and X3 are given below

X1 = 1.412mm
X2 = 1.412mm
X3 = 0.850mm

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:

1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.

2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.

National Semiconductor
Americas Customer
Support Center

Email: [e-mail]
Tel: [phone]

National Semiconductor
Europe Customer Support Center

Fax: [phone]

Email: [e-mail]
Deutsch Tel: [phone]
English Tel: [phone]
Français Tel: [phone]

National Semiconductor
Asia Pacific Customer
Support Center

Email: [e-mail]

National Semiconductor
Japan Customer Support Center

Fax: [phone]
Email: [e-mail]
Tel: [phone]

www.national.com

LM3700/LM3701 Microprocessor Supervisory Circuit with Low Line Output

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.