Page 1
LM1971
Overture
™
Audio Attenuator Series
Digitally Controlled 62 dB Audio Attenuator with/Mute
General Description
The LM1971 is a digitally controlled single channel audio attenuator fabricated on a CMOS process. Attenuation is variable in 1 dB steps from 0 dB to −62 dB. A mute function disconnects the input from the output, providing over 100 dB of
attenuation.
The performance of the device is exhibited by its ability to
change attenuation levels without audible clicks or pops. In
addition, the LM1971 features a low Total Harmonic Distortion (THD) of 0.0008%, and a Dynamic Range of 115 dB,
making it suitable for digital audio needs. The LM1971 is
available in both 8-pin plastic DIP or SO packages.
The LM1971iscontrolled by a TTL/CMOS compatible 3-wire
serial digital interface. The active low LOAD line enables the
data input registers while the CLOCK line provides system
timing. Its DATApin receives serial data on the rising edge of
each CLOCK pulse, allowing the desired attenuation setting
to be selected.
Key Specifications
n Total harmonic distortion 0.0008%(typ)
n Frequency response
>
200 kHz (−3 dB) (typ)
n Attenuation range (excluding mute) 62 dB (typ)
n Dynamic range 115 dB (typ)
n Mute attenuation 102 dB (typ)
Features
n 3-wire serial interface
n Mute function
n Click and pop free attenuation changes
n 8-pin plastic DIP and SO packages available
Applications
n Communication systems
n Cellular Phones and Pagers
n Personal computer audio control
n Electronic music (MIDI)
n Sound reinforcement systems
n Audio mixing automation
Typical Application
Overture™is a trademark of National Semiconductor Corporation.
DS012353-1
FIGURE 1. Typical Audio Attenuator Application Circuit
May 1999
LM1971
Overture
Audio Attenuator Series Digitally Controlled 62 dB Audio Attenuator with Mute
© 1999 National Semiconductor Corporation DS012353 www.national.com
Page 2
Connection Diagram
Dual-In-Line Plastic or Surface Mount Package
DS012353-2
Top View
Order Number LM1971M or LM1971N
See NS Package Number M08A or N08E
www.national.com 2
Page 3
Absolute Maximum Ratings (Notes 1, 2)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
Supply Voltage, V
DD
15V
Voltage at any pin (GND −0.2V) to (V
DD
+0.2V)
ESD Susceptibility (Note 4) 3000V
Soldering Information
N Package (10s)
M Package
Vapor Phase (60s)
Infrared (15s)
260˚C
215˚C
220˚C
Power Dissipation (Note 3) 150 mW
Junction Temperature 150˚C
Storage Temperature −65˚C to +150˚C
Operating Ratings (Notes 1, 2)
Temperature Range
T
MIN
≤ TA≤ T
MAX
−20˚C ≤ TA≤ +85˚C
Thermal Resistance
M08A Package, θ
JA
167˚C/W
N08E Package, θ
JA
102˚C/W
Supply Voltage 4.5V to 12V
Electrical Characteristics (Notes 1, 2)
The following specifications apply for V
DD
=
+12V (V
REF
IN=+6V), V
IN
=
5.5 V
pk
, and f=1 kHz, unless otherwse specified.
Limits apply for T
A
=
25˚C. Digital inputs are TTL and CMOS compatible.
Symbol Parameter Conditions
LM1971
Units
(Limits)
Typical
(Note 5)
Limit
(Note 6)
I
S
Supply Current Digital Inputs Tied to 6V 1.8 3 mA (max)
THD Total Harmonic Distortion V
IN
= 0.5V
pk
@
0 dB Attenuation 0.0008 0.003
%
(max)
e
IN
Noise Input is AC Grounded
@
−12 dB Attenuation
A-Weighted (Note 7)
4.0 µV
DR Dynamic Range Referenced to Full Scale=+6 V
pk
115 dB
A
M
Mute Attenuation 102 96 dB (min)
Attenuation Step Size Error 0 dB to −62 dB 0.009 0.2 dB (max)
Absolute Attenuation Attenuation
@
0dB
Attenuation
@
−20 dB
Attenuation
@
−40 dB
Attenuation
@
−60 dB
Attenuation
@
−62 dB
0.1
−20.3
−40.5
−60.6
−62.6
0.5
−19.0
−38.0
−57.0
−59.0
dB (min)
dB (min)
dB (min)
dB (min)
dB (min)
I
LEAK
Analog Input Leakage Current Input is AC Grounded 5.8 100 nA (max)
Frequency Response 20 Hz–100 kHz
±
0.1 dB
R
IN
AC Input Impedance Pin 8, V
IN
=
1.0 V
pk
,f=1 kHz 40 20
60
kΩ (min)
kΩ (max)
I
IN
Input Current
@
Pins 4, 5, 6@0V<V
IN
<
5V 1.0 100 nA (max)
f
CLK
Clock Frequency 3 2 MHz (max)
V
IH
High-Level Input Voltage
@
Pins 4, 5, 6 2.0 V (min)
V
IL
Low-Level Input Voltage
@
Pins 4, 5, 6 0.8 V (max)
Note 1:
Absolute Maximum Ratings
indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.
Electrical Characteristics
state DC and AC electrical specifications under particular test conditions which
guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit
is given, however, the typical value is a good indication of device performance.
Note 2: All voltages are measured with respect to the GND pin (pin 3), unless otherwise specified.
Note 3: The maximum power dissipation must be derated at elevated temperatures and is dictated by T
JMAX
, θJA, and the ambient temperature TA. The maximum
allowable power dissipation is P
D
=
(T
JMAX–TA
)/θJAor the number given in the Absolute Maximum Ratings, whichever is lower. For the LM1971N and LM1971M,
T
JMAX
=
+150˚C, and the typical junction-to-ambient thermal resistance, θ
JA
, when board mounted is 102˚ C/W and 167˚ C/W, respectively.
Note 4: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
Note 5: Typicals are measured at 25˚C and represent the parametric norm.
Note 6: Limits are guarantees that all parts are tested in production to meet the stated values.
Note 7: Due to production test limitations, there is no limit for the Noise test. Please refer to the noise measurements in the Typical Performance Characteristics sec-
tion.
www.national.com3
Page 4
Pin Description
V
REF
IN (1): The V
REF
IN pin provides the reference for the
analog input signal. This pin should be biased at half of
the supply voltage, V
DD
, as shown in
Figure 1
and
Figure
6
.
OUT (2): The attenuated analog output signal comes from
this pin.
GND (3): The GND pin references the digital input signals
and is the lower voltage reference for the IC. Typicallythis
pin would be labeled “V
SS
” but the ground reference for
the digital logic input control is tied to this same point. With
a higher pin-count there would generally be separate pins
for these functions; V
SS
and Logic Ground. It is intended
that the LM1971 always be operated using a single voltage supply configuration, for which pin 3 (GND) should always be at system ground. If a bipolar or split-supply configuration are desired, level shifting circuitry is needed for
the digital logic control pins as they would be referenced
through pin 3 which would be at the negative supply. It is
highly recommended, however, that the LM1971 be used
in a unipolar or single-supply configuration.
LOAD (4): The LOAD input accepts a TTL or CMOS level
signal. This is the enable pin of the device, allowing data
to be clocked in while this input is low (0V). The GND pin
is the reference for this signal.
DATA (5): The DATA input accepts a TTL or CMOS level
signal. This pin is used to accept serial data from a microcontroller that will be latched and decoded to change the
channel’s attenuation level. The GND pin is the reference
for this signal.
CLOCK (6): The CLOCK input accepts a TTL or CMOS
level signal. The clock input is used to load data into the
internal shift register on the rising edge of the input clock
waveform. The GND pin is the reference for this signal.
V
DD
(7): The positive voltage supply should be placed to
this pin.
IN (8): The analog input signal should be placed to this
pin.
Typical Performance
Characteristics
Supply Current vs
Supply Voltage
DS012353-10
Supply Current vs
Temperature
DS012353-11
Noise Floor
Analog Measurement
DS012353-12
THD+NvsFreq and Amp
DS012353-13
THD+NvsFreq and Amp
DS012353-14
Noise Floor Spectrum by FFT
DS012353-15
www.national.com 4
Page 5
Typical Performance Characteristics (Continued)
THD+NvsAmplitude
DS012353-16
THD+NvsAmplitude
DS012353-17
Mute Attenuation
vs Frequency
DS012353-18
THD vs Freq by FFT
DS012353-19
THD vs Freq by FFT
DS012353-20
Output Impedance vs
Attenuation Level
DS012353-21
www.national.com5
Page 6
Application Information
SERIAL DATA FORMAT
The LM1971 uses a 3-wire serial communication format that
is easily controlled by a microcontroller. The timing for the
3-wire set, comprised of DATA,CLOCK, and LOAD is shown
in
Figure 2
. As depicted in
Figure 2
, the LOAD line is to go
low at least 150 ns before the rising edge of the first clock
pulse and is to remain low throughout the transmission of the
16 data bits. The serial data is composed of an 8-bit address,
which must always be set to 0000 0000 to select the single
audio channel, and 8 bits for attenuation setting. For both address data and attenuation setting data, the MSB is sent first
with the address data preceding the attenuation data. Please
refer to
Figure 3
to confirm the serial data format transfer
process.
Table1
shows the various Address and Data byte values for
different attenuation settings. Note that Address bytes other
than 0000 0000 are ignored.
µPOT SYSTEM ARCHITECTURE
The µPot’s digital interface is essentially a shift register
where serial data is shifted in, latched, and then decoded.
Once new data is shifted in, the LOAD line goes high, latching in the new data. The data is then decoded and the appropriate switch is activated to set the desired attenuation level.
This process is continued each and every time an attenuation change is made. When the µPot is powered up, it is
placed into the Mute mode.
µPOT DIGITAL COMPATIBILITY
The µPot’s digital interface section is compatible with TTL or
CMOS logic. The shift register inputs act upon a threshold of
two diode drops above the ground level (Pin 3) or approximately 1.4V.
TABLE 1. Attenuator Register Set Description
Address Register (Byte 0)
MSB LSB
A7–A0
0000 0000 Channel 1
0000 0001 Ignored
0000 0010 Ignored
Data Register (Byte 1)
Contents Attenuation (dB)
MSB LSB
D7–D0
0000 0000 0.0
0000 0001 1.0
0000 0010 2.0
0000 0011 3.0
::::: ::
0001 0000 16.0
0001 0001 17.0
0001 0010 18.0
0001 0011 19.0
::::: ::
0011 1101 61.0
0011 1110 62.0
0011 1111 96 (Mute)
0100 0000 96 (Mute)
::::: ::
1111 1110 96 (Mute)
1111 1111 96 (Mute)
DS012353-3
*Note: Load and clock falling edges can be coincident, however, the clock falling edge cannot be delayed more than 20 ns from the falling edge of load. It is
preferrable that the falling edge of clock occurs before the falling edge of load.
FIGURE 2. Timing Diagram
www.national.com 6
Page 7
Application Information (Continued)
µPOT LADDER ARCHITECTURE
The µPot contains a chain of R1/R2 resistor dividers in a ladder form, as shown in
Figure 4
. Each R1 is actually a series
of 8 resistors, with a CMOS switch that taps into the resistor
chain according to the attenuation level chosen. For any
given attenuation setting, there is only one CMOS switch
closed (no paralleling of ladders). The input impedance
therefore remains constant, while the output impedance
changes as the attenuation level changes. It is important to
note that the architecture is a series of resistor dividers, and
not a straight, tapped resistor, so the µPot is not a variable
resistor; it is a variable voltage divider.
ATTENUATION STEP SCHEME
The fundamental attenuation step scheme for the LM1971 is
shown in
Figure 5
. It is also possible to obtain any integer
value attenuation step through programming, in addition to
the 2 dB and 4 dB steps shown in
Figure 5
.All higher attenuation step schemes can have clickless and popless performance. Although it is possible to “skip” attenuation points by
not sending all of the data, clickless and popless performance will suffer. It is highly recommended that all of the
data points should be sent for each attenuation level. This
ensures flawless operation and performance when making
steps larger than 1 dB.
INPUT IMPEDANCE
The input impedance of a µPot is constant at a nominal
40 kΩ. Since the LM1971 is a single-supply operating device, it is necessary to have both input and output coupling
caps as shown in
Figure 1
. To ensure full low-frequency re-
sponse,a1µFcoupling cap should be used.
OUTPUT IMPEDANCE
The output impedance of a µPot varies typically between
25 kΩ and 35 kΩ and changes nonlinearly with step
changes. Since a µPot is made up of a resistor ladder network with logarithmic attenuation, the output impedance is
nonlinear. Due to this configuration, a µPot cannot be considered as a linear potentiometer; it is a logarithmic attenuator.
The linearity of a µPot cannot be measured directly without a
buffer because the input impedance of most measurement
systems is not high enough to provide the required accuracy.
The lower impedance of the measurement system would
load down the output and an incorrect reading would result.
To prevent loading, a JFET input op amp should be used as
the buffer/amplifier.
OUTPUT BUFFERING
There are two performance issues to be aware of that are related to a µPot’s output stage. The first concern is to prevent
audible clicks with attenuation changes, while the second is
to prevent loading and subsequent linearity errors. The output stage of a µPot needs to be buffered with a low input bias
DS012353-4
FIGURE 3. Serial Data Format Transfer Process
DS012353-5
FIGURE 4. Resistor Ladder Architecture
LM 1971 Channel Attenuation
vs Digital Step Value
(1 dB, 2 dB, and 4 dB Steps)
DS012353-6
FIGURE 5. LM1971 Attenuation Step Scheme
www.national.com7
Page 8
Application Information (Continued)
current op amp to keep DC shifts inaudible. Additionally, the
output of µPot needs to see a high impedance to keep linearity errors low.
Attenuation level changes cause changes in the output impedance of a µPot. Output impedance changes in the presence of a large input bias current for a buffer/amplifier will
cause a DC shift to occur. Neglecting amplifier gains and
speaker sensitivities, the audibility of a DC shift is dependent
upon the output impedance change times the required input
bias current. As an example,a5kΩimpedance change
timesa1µAbias current results ina5mVDCshift; a level
that is barely audible without any music material in the system. An op amp with a bias current of 200 pA for the same
5kΩchange results in an inaudible 1 µV DC shift. Since the
worst case output impedance changes are on the order of
several kΩ, a bias current much less than 1 µAis required for
highest performance. In order to further quantify DC shifts,
please refer to the Output Impedance vs Attenuation graph
in the TypicalPerformance Characteristics section and relate worst case impedance changes to the selected buffer/
amplifier input bias current.
Without the use of a high input impedance (
>
1MΩ)opamp
for the buffer/amplifier,loading will occur that causes linearity
errors in the signal. To ensure the highest level of performance, a JFET or CMOS input high input impedance op
amp is required.
One common application that requires gain at the output of a
µPot is input signal volume control. Depending upon the input source material, the LM1971 provides a means of controlling the input signal level. With a supply voltage range of
4.5V to 12V, the LM1971 has the ability of controlling fairly
inconsistent input source signal levels. Using an op amp with
gain at the µPot’s output, as shown in
Figure 7
, will also allow the system dynamic range to be increased. JFET op
amps like the LF351 and the LF411 are well suited for this
application. If active half-supply buffering is also desired,
dual op amps like the LF353 and the LF412 could be used.
For low voltage supply applications, op amps like the CMOS
LMC6041 are preferred. This part has a supply operating
range from 4.5V–15.5V and also comes in a surface mount
package.
µPOT HALF-SUPPLY REFERENCING
The LM1971 operates off of a single supply, with half-supply
biasing supplied at the V
REF
IN terminal (Pin 1). The easiest
and most cost effective method of providing this half-supply
is a simple resistor divider and bypass capacitor network
shown in
Figure 1
. The capacitor not only stabilizes the
half-supply node by “holding” the voltage nearly constant,
but also decouples high frequency signals on the supply to
ground. Signal feedthrough, power supply ripple and fluctuations that are not properly filtered could cause the performance of the LM1971 to be degraded.
A more stable half-supply node can be obtained by actively
buffering the resistor divider network with a voltage follower
as shown in
Figure 6
. Supply fluctuations are then isolated
by the high input impedance/low output impedance mismatch associated with effective filtering. Since the LM1971 is
a single channel device, using a dual JFET input op amp is
optimum for both output buffering and half-supply biasing.
A 10 µF capacitor or larger is recommended for better
half-supply stabilization. For added rejection of higher fre-
quency power supply fluctuations, a smaller capacitor
(0.01 µF–0.1 µF) could be added in parallel to the 10 µF
capacitor.
LOGARITHMIC GAIN AMPLIFIER
The µPot is capable of being used in the feedback loop of an
op amp to create a gain controlled amplifier as shown in
Fig-
ure 8
. In this configuration the attenuation levels from
Table
1
become gain levels with the largest possible gain value being 62 dB. For most applications, 62 dB of gain will cause
signal clipping to occur. However, this can be controlled
through programming. It is important to note that when in
mute mode the input is disconnected from the output, thus
placing the amplifier in open-loop gain state. In this mode,
the amplifier will behave as a comparator. Care should be
taken with the programming and design of this type of circuit.
To provide the best overall performance, a high input impedance, low input bias current op amp should be used.
DS012353-7
FIGURE 6. Higher Performance
Active Half-Supply Buffering
DS012353-8
FIGURE 7. Active Reference with Active Gain Buffering
DS012353-9
FIGURE 8. Logarithmic Gain Amplifier Circuit
www.national.com 8
Page 9
Application Information (Continued)
MUTE FUNCTION
A major feature of the LM1971 is its ability to mute the input
signal to an attenuation level of 102 dB. This is accomplished internally by physically disconnecting the output from
the input while also grounding the output pin through approximately 2 kΩ.
The mute function is obtained during power-up of the device
or by sending any binary data of 0011 1111 and above serially to the device. The device may be placed into mute at any
time during operation, allowing the designer to make the
mute command accessible to the end-user.
DC INPUTS
Although the µPot was designed to be used as an attenuator
for signals within the audio spectrum, it is also capable of
tracking and attenuating an input DC voltage. The device will
track voltages to either supply rail.
One point to remember about DC tracking is that with a
buffer at the output of the µPot, the resolution of DC tracking
will depend upon the gain configuration of that output buffer
and its supply voltage. Also, the output buffer’s supply voltage does not have to be the same as the µPot’s supply voltage. Giving the buffer some gain can provide more resolution when tracking small DC voltages.
www.national.com9
Page 10
Physical Dimensions inches (millimeters) unless otherwise noted
Order Number LM1971M
8-Lead (0.150" Wide) Molded Small Outline Package, JEDEC
NS Package Number M08A
Order Number LM1971N
8-Lead (0.300" Wide) Molded Dual-In-Line Package
NS Package Number N08E
www.national.com 10
Page 11
Notes
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe
Fax: +49 (0) 1 80-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 1 80-530 85 85
English Tel: +49 (0) 1 80-532 78 32
Français Tel: +49 (0) 1 80-532 93 58
Italiano Tel: +49 (0) 1 80-534 16 80
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: sea.support@nsc.com
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
www.national.com
LM1971
Overture
Audio Attenuator Series Digitally Controlled 62 dB Audio Attenuator with Mute
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Loading...