Datasheet LM-185WH1-TLA1 Service manual (LG)

www.jxlcd.com

SPECIFICATION

( ) Preliminary Specification (◆) Final Specification

LM185WH1

Liquid Crystal Display

Product Specification

FOR

APPROVAL

18.5” WXGA TFT LCDTitle

BUYER

MODEL

www.jxlcd.com

SIGNATURE DATE

/

Acer

SUPPLIER LG Display Co., Ltd.

*MODEL LM185WH1

SUFFIX TLA1

*When you obtain standard approval, please use the above model name without suffix

APPROVED BY

G.T. KIM / G.Manager

REVIEWED BY

K.H. Hwang / Manager [C]

J. H. Lee / Manager [M]

D.H. Kang / Manager [P]

PREPARED BY

S.H. Lee / Engineer

DATE

Please return 1 copy for your confirmation With your signature and comments.

Ver. 1.0 Sep., 10, 2008

Product Engineering Dept.

LG Display Co., Ltd

2 / 32

Product Specification

Contents

LM185WH1

Liquid Crystal Display

No

COVER

CONTENTS

RECORD OF REVISIONS

GENERAL DESCRIPTION

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL SPECIFICATIONS

1)

ELECTRICAL CHARACTERISTICS

2)

INTERFACE CONNECTIONS

3)

LVDS characteristics

4)

SIGNAL TIMING SPECIFICATIONS

5)

SIGNAL TIMING WAVEFORMS

6)

COLOR INPUT DATA REFERNECE

7)

POWER SEQUENCE

8)

POWER DIP CONDITION

OPTICAL SFECIFICATIONS

www.jxlcd.com

MECHANICAL CHARACTERISTICS

ITEM

Page

1

2

3

41

52

63

6

9

12

15

16

17

18

19

204

255

RELIABILITY

INTERNATIONAL STANDARDS

1)

SAFETY

2)

EMC

PACKING

1)

DESIGNATION OF LOT MARK

2)

PACKING FORM

Ver. 1.0 Sep., 10, 2008

286

297

29

308

30

31PRECAUTIONS9

31MOUNTING PRECAUTIONS1)

31OPERATING PRECAUTIONS2)

32ELECTROSTATIC DISCHARGE CONTROL3)

32PRECAUTIONS FOR STRONG LIGHT EXPOSURE4)

32STROAGE5)

32HANDLING PRECAUTIONS FOR PROTECTION FILM6)

3 / 32

Product Specification

Record of revisions

Revision No DescriptionDate Page

LM185WH1

Liquid Crystal Display

Ver 1.0

Sep.,10,2008

www.jxlcd.com

Final Specifications

Ver. 1.0 Sep., 10, 2008

4 / 32

LM185WH1

Liquid Crystal Display

Product Specification

1. General description

LM185WH1-TLA1 is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent Lamp(CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in the normally white mode. It has a

18.5 inch diagonally measured active display area with WXGA resolution (768 vertical by 1366 horizontal pixel array) Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot, thus, presenting a palette of more than 16,7M colors with Advanced-FRC(Frame Rate Control). It has been designed to apply the interface method that enables low power, high speed, low EMI. FPD Link or compatible must be used as a LVDS(Low Voltage Differential Signaling) chip. It is intended to support applications where thin thickness, wide viewing angle, low power are critical factors and graphic displays are important. In combination with the vertical arrangement of the sub-pixels, the LM185WH1-TLA1 characteristics provide an excellent flat panel display for office automation products such as monitors.

FIG. 1 Block diagram

RGB

Source driver circuit

LVDS

pair #1

LVDS

pair #2

CN1

www.jxlcd.com

+5V

CN2 (2pin)

CN3 (2pin)

Power circuit

VLCD

Timing

controller

block

S1

G1

TFT-LCD Panel

(1366×RGB×768 pixels)

G768

Backlight assembly (2 CCFLs)

S1366

General features

Active screen size 18.51 inches (470.1mm) diagonal

Outline Dimension 430.4(H) x 254.6(V) x 13.0(D) mm(Typ.)

Pixel Pitch 0.10*RGB(H)mm x 0.30(V)mm

Pixel Format 1366 horizontal By 768 vertical Pixels. RGB stripe arrangement

Interface LVDS 2Port

Color depth 16.7M colors

Luminance, white 300 cd/m2 ( Center 1Point, typ)

Viewing Angle (CR>10) R/L 170(Typ.), U/D 160(Typ.)

Power Consumption

Weight 1550 g (Typ.)

Display operating mode Transmissive mode, Normally White

Surface treatments Hard coating (3H), Anti-glare treatment of the front polarizer

Ver. 1.0 Sep., 10, 2008

Total 13.60W(Typ.), (3.10W@V

, 10.50 W@IBL =7.5mA)

LCD

5 / 32

Product Specification

2. Absolute maximum ratings

The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.

Table 1. Absolute maximum ratings

LM185WH1

Liquid Crystal Display

60

Values

90%

MaxMin

60%

40%

10%

Hu mi dit y [( % )R H]

Parameter Notes

Power Supply Input Voltage

Operating Temperature

Storage Temperature

Operating Ambient Humidity

Storage Humidity

Note : 1. Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 °C Max, and no condensation of water.

FIG. 2 Temperature and relative humidity

www.jxlcd.com

Wet Bulb Temperature [℃]

10

0

Symbol

LCD

OP

ST

OP

ST

50

40

30

20

Units

°C500T

°C60-20T

%RH9010H

Storage

Operation

At 25℃Vdc+6.0-0.3V

1

10 20 30 40 50 60 70 800-20

Dry Bulb Temperature [℃]

Ver. 1.0 Sep., 10, 2008

6 / 32

LM185WH1

Liquid Crystal Display

Product Specification

3. Electrical specifications

3-1. Electrical characteristics

It requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input power for the CCFL/Backlight, is typically generated by an inverter. The inverter is an external unit to the LCDs.

Table 2. Electrical characteristics

Parameter Symbol

MODULE :

Power Supply Input Voltage

Permissive Power Input Ripple

Power Supply Input Current

Power Consumption

Inrush current

Note :

1. The specified current and power consumption are

under the VLCD=5.0V, 25  2°C,f

whereas mosaic pattern(8 x 6) is displayed and fV is the frame frequency.

2. The current is specified at the maximum current pattern.

3. Permissive power ripple should be measured under VCC=5.0V, 25°C, fV (frame frequency)=75Hz condition and At that time, we recommend the bandwidth configuration of oscilloscope is to be under 20MHz.

4. The duration of rush current is about 5ms and rising time of power Input is 500us  20%.

FIG.3 pattern for Electrical characteristics

www.jxlcd.com

LCD

LCD-MOSAIC

I

LCD-BLACK

LCD

RUSH

=60Hz condition

V

Values

MaxTypMin

Vdc5.55.04.5V

NotesUnit

3V0.2--V

1mA715620-I

2mA830720-

1Watt3.583.10-P

3A3.0--I

power consumption measurement

White : 255Gray Black : 0Gray

Mosaic Pattern(8 x 6)

Ver. 1.0 Sep., 10, 2008

power input ripple

Full Black Pattern

7 / 32

Product Specification

Table 3. Electrical characteristics

LM185WH1

Liquid Crystal Display

Parameter Symbol

LAMP :

Operating Voltage

Operating Current

at 25 °C

at 0 °C

Operating Frequency

Discharge Stabilization Time

Power Consumption

Note : The design of the inverter must have specifications for the lamp in LCD Assembly. The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced by the characteristics of the DC-AC inverter. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. When you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter (no lighting, flicker, etc) never occurs. When you confirm it, the LCD–Assembly should be operated in the same condition as installed in you instrument.

※ Do not attach a conducting tape to lamp connecting wire. If the lamp wire attach to a conducting tape, TFT-LCD Module has a low luminance and the inverter has abnormal action. Because leakage current is occurred between lamp wire and conducting tape.

www.jxlcd.com

V

BL

S

BL

685

(8.0mA)

Values

700

(7.5mA)

MaxTypMin

860

(3.0mA)

8.07.53.0I

1250

1550

NotesUnit

RMS

V

RMS

V

RMS

1, 2V

1mA

1, 3Vs Established Starting Voltage

4kHz706040f

1, 5Min3--T

6Watt10.9610.50P

1, 7Hrs-50,000 Life Time

1. Specified values are for a single lamp.

2. Operating voltage is measured at 25  2°C. The variance of the voltage is  10%.

3. The voltage above VS should be applied to the lamps for more than 1 second for start-up. (Inverter open voltage must be more than lamp starting voltage.)

Otherwise, the lamps may not be turned on. The used lamp current is the lamp typical current.

4. Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may cause beat on the display. Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference.

5. Let’s define the brightness of the lamp after being lighted for 5 minutes as 100%.

TS is the time required for the brightness of the center of the lamp to be not less than

95%.

6. The lamp power consumption shown above does not include loss of external inverter. The used lamp current is the lamp typical current. (PBL = VBL x IBL x N

7. The life is determined as the time at which brightness of the lamp is 50% compared to that

of initial value at the typical lamp current on condition of continuous operating at 25  2°C.

Ver. 1.0 Sep., 10, 2008

Lamp

)

8 / 32

Liquid Crystal Display

Product Specification

Note :

8. The output of the inverter must have symmetrical(negative and positive) voltage waveform and symmetrical current waveform (Unsymmetrical ratio is less than 10%). Please do not use the inverter which has unsymmetrical voltage and unsymmetrical current and spike wave. Requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following.It shall help increase the lamp lifetime and reduce leakage current.

a. The asymmetry rate of the inverter waveform should be less than 10%. b. The distortion rate of the waveform should be within √2 ±10%. * Inverter output waveform had better be more similar to ideal sine wave.

* Asymmetry rate:

I p

| I p – I –p | / I

x 100%

rms

LM185WH1

I -p

9. The inverter which is combined with this LCM, is highly recommended to connect

coupling(ballast) condenser at the high voltage output side. When you use the inverter which has not coupling(ballast) condenser, it may cause abnormal lamp lighting because of biased mercury as time goes.

10.In case of edgy type back light with over 4 parallel lamps, input current and voltage wave form should be synchronized

www.jxlcd.com

* Distortion rate

I p (or I –p) / I

rms

Ver. 1.0 Sep., 10, 2008

9 / 32

Product Specification

3-2. Interface connections

LCD connector(CN1) : IS100-L30B-C23 (UJU), 187024-30091 (P-TWO) Mating connector : FI-X30H and FI-X30HL (JAE) or Equivalent

Table 4. Module connector(CN1) pin configuration

LM185WH1

Liquid Crystal Display

Pin No

1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30

Symbol Description

RXO0 RXO0+ RXO1 RXO1+ RXO2 RXO2+ GND RXOC RXOC+ RXO3 RXO3+ RXE0 RXE0+

www.jxlcd.com

GND RXE1 RXE1+ GND RXE2 RXE2+ RXEC RXEC+ RXE3 RXE3+ GND NC NC PWM_OUT VLCD VLCD VLCD

Minus signal of 1st channel 0 (LVDS) Plus signal of 1st channel 0 (LVDS) Minus signal of 1st channel 1 (LVDS) Plus signal of 1st channel 1 (LVDS) Minus signal of 1st channel 2 (LVDS) Plus signal of 1st channel 2 (LVDS) Ground (AGP) Minus signal of 1st clock channel (LVDS) Plus signal of 1st clock channel (LVDS) Minus signal of 1st channel 3 (LVDS) Plus signal of 1st channel 3 (LVDS) Minus signal of 2nd channel 0 (LVDS) Plus signal of 2nd channel 0 (LVDS) Ground Minus signal of 2nd channel 1 (LVDS) Plus signal of 2nd channel 1 (LVDS) Ground Minus signal of 2nd channel 2 (LVDS) Plus signal of 2nd channel 2 (LVDS) Minus signal of 2nd clock channel (LVDS) Plus signal of 2nd clock channel (LVDS) Minus signal of 2nd channel 3 (LVDS) Plus signal of 2nd channel 3 (LVDS) Ground No Connection (For LCD internal use only.) No Connection (For LCD internal use only.) Reference signal for inverter control Power Supply (5.0V) Power Supply (5.0V) Power Supply (5.0V)

Ver. 1.0 Sep., 10, 2008

10 / 32

FIG. 4 Connector diagram

#1 #30

1’st signal pairs

#1 #30

LM185WH1

Liquid Crystal Display

Product Specification

187024-30091 (P-TWO)

2’nd signal pairs

Power(5V)

PWM signal

Rear view of LCM

Note:

1. NC: No Connection.

should also be connected to the LCD’s metal frame.

3. All V

4. Input Level of LVDS signal is based on the IEA 664 Standard.

5. PWM_OUT is a reference signal for inverter control. This PWM signal is synchronized with vertical frequency. Its frequency is 3 times of vertical frequency, and its duty ratio is 50%. If the system don’t use this pin, do not connect.

www.jxlcd.com

2. All GND(ground) pins should be connected together and to Vss which

(power input) pins should be connected together.

LCD

Ver. 1.0 Sep., 10, 2008

11 / 32

LM185WH1

Liquid Crystal Display

Product Specification

The backlight interface connector is a model 35001HS-02LD manufactured by YEONHO. The mating connector part number are 35001WR-02L(2pin) or equivalent. The pin configuration for the connector is shown in the table below.

Table 5. Backlight connector pin configuration(CN2,CN3)

1

2

Notes: 1. The high voltage power terminal is colored gray.

2. The low voltage pin color is black.

FIG. 5 Backlight connector diagram

www.jxlcd.com

Symbol

HV

LV

Description

High Voltage for Lamp

Low Voltage for Lamp

Lamp1

Lamp2

Notes

1

2

CN2

CN3

Ver. 1.0 Sep., 10, 2008

12 / 32

3-3. LVDS characteristics

LVDS +

LVDS -

0V

V

CM

# |VID| = |(LVDS+) – (LVDS-)| # VCM= {(LVDS+) + (LVDS-)}/2

|VID|

V

IN_MAXVIN_MIN

3-3-1. DC Specification

LM185WH1

Liquid Crystal Display

Product Specification

NotesUnitMaxMinSymbolDescription

-mV600200|VID|LVDS Differential Voltage

LVDS Common mode Voltage

LVDS Input Voltage Range

3-3-2. AC Specification

www.jxlcd.com

LVDS Clock

LVDS Data

LVDS Clock to Data Skew Margin

LVDS Clock to Clock Skew Margin (Even to Odd)

Maximum deviation of input clock frequency during SSC

t

SKEW

CM

IN

T

clk

SKEW (Fclk

t

1) 85 MHz > Fclk ≥ 65 MHz : - 400 ~ +400

2) 65 MHz > Fclk ≥ 25 MHz : - 600 ~ +600

SKEW_EO

= 1/T

SKEW

DEV

clk

)

- 1/7

600-

+ 1/7t

-V1.80.6V

-V2.10.3V

NotesUnitMaxMinSymbolDescription

85MHz > Fclk ≥ 65MHz

ps+ 400 400-t

65MHz > Fclk ≥ 25MHz

ps+ 600t

T

clk

%± 3-F

-

Maximum modulation frequency

MOD

of input clock during SSC

Ver. 1.0 Sep., 10, 2008

KHz200-F

-

13 / 32

Product Specification

t SKEW_ EO

LM185WH1

Liquid Crystal Display

LVDS Odd Clock

LVDS Even Clock

LVDS Even Data

Tclk

clk

T

< Clock skew margin between channel >

Freq.

F

max

F

center

F

min

1

F

MOD

< Spread Spectrum >

www.jxlcd.com

center

* F

Time

DEV

3-3-3. LVDS Data format

Tclk

RCLK +

RXinO0 +/-

RXinO1 +/-

RXinO2 +/-

RXinO3 +/-

RXinE 0 +/-

RXinE 1 +/-

RXinE 2 +/-

RXinE 3 +/-

OR3 OR2 OR1 OR0

OG4 OG3 OG2 OG1

OB5 OB4 OB3 OB2

OG7 OG6 OR7 OR6

ER3 ER2 ER1 ER0

EG4 EG3 EG2 EG1

EB5 EB4 EB3 EB2

EG7 EG6 ER7 ER6

Tclk * 1/7

OG0 OR5 OR4 OR3 OR2 OR1 OR0

EB1 EB0 EG5 EG4 EG3 EG2 EG1

Ver. 1.0 Sep., 10, 2008

Tclk * 4/7 Tclk * 3/7

OB1 OB0 OG5 OG4 OG3 OG2 OG1

VSYNC HSYNC

DE

X OB7 OB6 OG7 OG6 OR7 OR6

EG0 ER5 ER4 ER3 ER2 ER1 ER0

VSYNC HSYNC

DE

X EB7 EB6 EG7 EG6 ER7 ER6

OB5 OB4 OB3 OB2

EB5 EB4 EB3 EB2

Current(Nth) CyclePrevious(N-1)th Cycle Next(N+1)

< LVDS Data Format >

OG0 OR5 OR4

OB1 OB0 OG5

VSYNC HSYNC

DE

X OB7 OB6

EG0 ER5 ER4

EB1 EB0 EG5

VSYNC HSYNC

DE

X EB7 EB6

th Cycle

MSB R7

R6

R5

R4

R3

R2

R1

R0LSB

* ODD = 1st Pixel

EVEN = 2nd Pixel

14 / 32

LM185WH1

Liquid Crystal Display

Product Specification

Table 6. Required signal assignment for Flat Link(NS:DS90CF383) transmitter

Pin # Require SignalPin Name Pin # Require SignalPin Name

1 Power Supply for TTL InputVCC 29 Ground pin for TTLGND

2 TTL Input (R7)D5 30 TTL Input (DE)D26

3 TTL Input (R5)D6 31 TTL Level clock InputTX CLKIN

4 TTL Input (G0)D7 32 Power Down InputPWR DWN

5 Ground pin for TTLGND 33 Ground pin for PLLPLL GND

6 TTL Input (G1)D8 34 Power Supply for PLLPLL VCC

7 TTL Input (G2)D9 35 Ground pin for PLLPLL GND

8 TTL Input (G6)D10 36 Ground pin for LVDSLVDS GND

9 Power Supply for TTL InputVCC 37 Positive LVDS differential data output 3TxOUT3＋

10 TTL Input (G7)D11 38 Negative LVDS differential data output 3TxOUT3－

11 TTL Input (G3)D12 39 Positive LVDS differential clock outputTX CLKOUT＋

12 TTL Input (G4)D13 40 Negative LVDS differential clock outputTX CLKOUT－

13 Ground pin for TTLGND 41 Positive LVDS differential data output 2TX OUT2＋

14 TTL Input (G5)D14 42 Negative LVDS differential data output 2TX OUT2－

15 TTL Input (B0)D15 43 Ground pin for LVDSLVDS GND

16 TTL Input (B6)D16 44 Power Supply for LVDSLVDS VCC

17 Power Supply for TTL InputVCC 45 Positive LVDS differential data output 1TX OUT1＋

19 TTL Input (B1)D18

20 TTL Input (B2)D19

22 TTL Input (B3)D20

23 TTL Input (B4)D21

24 TTL Input (B5)D22

25 TTL Input (RSVD)D23

26 Power Supply for TTL InputVCC 54 TTL Input (R2)D2

www.jxlcd.com

46 Negative LVDS differential data output 1TX OUT1－18 TTL Input (B7)D17

47 Positive LVDS differential data output 0TX OUT0＋

48 Negative LVDS differential data output 0TX OUT0－

49 Ground pin for LVDSLVDS GND21 Ground pin for TTL InputGND

50 TTL Input (R6)D27

51 TTL Input (R0)D0

52 TTL Input (R1)D1

53 Ground pin for TTLGND

55 TTL Input (R3)D327 TTL Input (HSYNC)D24

56 TTL Input (R4)D428 TTL Input (VSYNC)D25

Notes : Refer to LVDS Transmitter Data Sheet for detail descriptions.

Ver. 1.0 Sep., 10, 2008

15 / 32

LM185WH1

Liquid Crystal Display

Product Specification

3-4. Signal timing specifications

This is the signal timing required at the input of the User connector. All of the interface signal timing should be satisfied with the following specifications for it’s proper operation.

Table 7. Timing table

D

CLK

Horizontal

Vertical

DE (Data Enable)

Data

www.jxlcd.com

Parameter

Period

Frequency

Horizontal Valid

H Period Total

Hsync Frequency

Vertical Valid

V Period Total

Vsync Frequency

DE Setup Time

www.jxlcd.com

DE Hold Time

Data Setup Time

Data Hold Time

Symbol

t

CLK

f

CLK

t

HV

t

HP

H

t

VV

VP

V

SI

HI

t

SD

HD

Min.

18.4

35.7

683

723

768

4

Typ.

23.4

42.9

683

896

768

-

Max.

28.0

54.4

683

1023

768

1108798776t

--4t

-

--4t

Unit

ns

MHz

t

CLK

kHz60.647.939.9f

t

HP

Hz766050f

ns

Pixel frequency : Typ.85.8MHz (2pixel / clk)

For D

Notes

CLK

Note:

1. LM185WH1-TLA1 is DE Only mode operation. The input of Hsync & Vsync signal does not have an effect on LCD normal operation.

2. The performance of the electro-optical characteristics may be influenced by variance of the vertical refresh rates.

3. Horizontal period should be even.

Ver. 1.0 Sep., 10, 2008

16 / 32

Product Specification

3-5. Signal timing waveforms

1. DCLK , DE, DATA waveforms

t

CLK

Dclk

t

SD

LM185WH1

Liquid Crystal Display

t

HD

Valid

Invalid

Data

DE(Data Enable)

2. Horizontal waveform

www.jxlcd.com

DE(Data Enable)

3. Vertical waveform

DE(Data Enable)

Invalid

t

SI

tHP

tHV

t

VP

tVV

t

HI

DE

Ver. 1.0 Sep., 10, 2008

17 / 32

LM185WH1

Liquid Crystal Display

Product Specification

3-6. Color input data reference

The brightness of each primary color (red,green and blue) is based on the 8bit gray scale data input for the color ; the higher the binary input, the brighter the color. The table below provides a reference for color versus data input.

Table 8. Color data reference

Input Color Data

Basic Color

Red

Green

Blue

Color

Black Red (255) Green (255) Blue (255) Cyan Magenta Yellow White

Red(000) Dark Red(001) Red(002)

- - - - - - - - -

- - - - - - - - Red(253) Red(254) Red(255) Bright

Green(000) Dark Green(001) Green(002)

- - - - - - - - -

- - - - - - - - Green(253) Green(254) Green(255)Bright

Blue(000) Dark Blue(001) Blue(002)

- - - - - - - - -

- - - - - - - - Blue(253) Blue(254) Blue(255) Bright

www.jxlcd.com

Red

MSB LSB

R7 R6 R5 R4 R3 R2 R1 R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 B6 B5 B4 B3 B2 B1 B0

0

1

0

1

0

1

-

1

0

1

0

-

0

-

0

MSB LSB

0

1

0

1

0

1

0

1

0

1

0

-

1

0

1

0

-

0

1

0

1

0

1

0

-

0

0 0 1 0 1 0 1 1

0 0 0

-

0 0 0

-

1 1 1

0 0 0

-

0 0 0

Green

0

1

0

1

0

1

0

-

0

-

1

0

-

0

Blue

MSB LSB

0

1

0

1

0

1

0

1

0

-

0

1

0

1

0

-

1

0

1

0

1

0

1

0

-

0

1

0

1

0

1

0

1

0

1

0

-

0

-

0

1

0

1

0

-

1

0

1

0

1

Ver. 1.0 Sep., 10, 2008

18 / 32

3-7. Power sequence

VLCD Power Supply For LCD

Interface Signal (Tx)

Product Specification

90% 90%

10%

T2 T5 T7

T1

Valid data

LM185WH1

Liquid Crystal Display

10%

0V

Power for LAMP

Table 9. Power sequence

www.jxlcd.com

Parameter

Notes :

1. Please avoid floating state of interface signal at invalid period.

2. When the interface signal is invalid, be sure to pull down the power supply for LCD V

3. Lamp power must be turn on after power supply for LCD an interface signal are valid.

to 0V.

LCD

OFF

T3

Lamp on

Values

T4

OFF

MaxTypMin

--200T4

Units

ms10-0.5T1

ms50-0.01T2

ms--500T3

ms

ms50-0.01T5

s--1T7

Ver. 1.0 Sep., 10, 2008

19 / 32

Product Specification

LM185WH1

Liquid Crystal Display

3-8. V

FIG. 6 Power dip condition

1) Dip condition

Power dip condition

LCD

V

LCD

4.5V

3.5V

t

d

GND(ground)

2) V

LCD

V

3.5V ≤V

＜ 3.5V

www.jxlcd.com

-dip conditions should also follow the Power On/Off conditions for supply voltage.

LCD

＜ 4.5V , td≤20ms

LCD

Ver. 1.0 Sep., 10, 2008

20 / 32

LM185WH1

Liquid Crystal Display

Product Specification

4. Optical specification

Optical characteristics are determined after the unit has been ‘ON’ for 30 minutes in a dark environment at 25°C. The values specified are at an approximate distance 50cm from the LCD

surface at a viewing angle of  and  equal to 0 °.

FIG. 7 presents additional information concerning the measurement equipment and method.

FIG. 7 Optical characteristic measurement equipment and method

LCD Module

Optical

Stage(x,y)

50cm

Pritchard 880 or equivalent

Table 10. Optical characteristics

SymbolParameter

Surface Luminance, white Luminance Variation

Response Time

www.jxlcd.com

Color Coordinates [CIE1931]

Viewing Angle (CR>5)

x axis, right(=0°)

Viewing Angle (CR>10)

Luminance uniformity Angular dependence (TCO’03)

Color grayscale linearity

x axis, left (=180°) y axis, up (=90°) y axis, down (=270°)

x axis, right(=0°) x axis, left (=180°) y axis, up (=90°)

Rise Time Decay Time

www.jxlcd.com

RED

GREEN

BLUE

WHITE



WHITE

WH

Rx

r

l u d

r

l u d y axis, down (=270°)

Ta= 25°C, V

9P

R

D

Typ

-0.03

=5.0V, fV=60Hz f

LCD

Values

0.642

0.334Ry

0.304Gx

0.608Gy

0.146Bx

0.073By

0.313Wx

0.329Wy

8875 8570 8570

8570 7560 8570

MaxTypMin

-1000600CRContrast Ratio

-300250L

Typ

+0.03

= 42.9MHz, IBL=7.5mA

CLK

NotesUnits

2

2cd/m

%1.5Crosstalk

1

3%75 4 ms2.61.1-Tr 4 ms7.43.9-Tr

5Degree8875

5Degree8570

61.7--LR

80.018Δu’v’

Ver. 1.0 Sep., 10, 2008

21 / 32

Liquid Crystal Display

Product Specification

Notes :

1. Contrast ratio(CR) is defined mathematically as :It is measured at center point(1)

Surface luminance with all white pixels Contrast ratio = --------------------------------------------------------- Surface luminance with all black pixels

2. Surface luminance is the luminance value at center 1 point(1) across the LCD surface 50cm from the surface with all pixels displaying white. For more information see FIG 8.

LM185WH1

3. The variation in surface luminance , 

Minimum (P1,P2 …..P9)



Maximum (P1,P2 …..P9)

For more information see Figure 8.

FIG. 8 Luminance measuring point

V

= --------------------------------------------- *100

WHITE

www.jxlcd.com

H/2

V/2

5 6

V/10

7

H

H/10

3

1

8

is defined as

WHITE

42

9

H

H/2

V/2

V

Active Area

Ver. 1.0 Sep., 10, 2008

H : 409.800 mm V : 230.400 mm @ H,V : Active Area

22 / 32

LM185WH1

Normal

Y

E







= 0, Right



= 180, Left



= 270, Down



= 90, Up

Liquid Crystal Display

Product Specification

Notes :

4. Response time is the time required for the display to transition from black to white (Decay Time, TrD) and from white to black (Rise Time, TrR) The sampling rate is 2,500 sample/sec. For additional information see FIG. 9.

The response time is defined as the following figure and shall be measured by switching the input signal for each gray to gray.

FIG. 9 Response time

Tr

R

100

90

Optical

response

[%]

5. Viewing angle is the angle at which the contrast ratio is greater than 10 or 5. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG. 10 .

FIG. 10 Viewing angle

www.jxlcd.com

10

white black white

0

Tr

D

Ver. 1.0 Sep., 10, 2008

23 / 32

Liquid Crystal Display

Product Specification

Notes :

6. Luminance Uniformity - angular – dependence (LR& TB)

TCO ‘03 Luminance uniformity – angular dependence, is the capacity of the VDU to present the same Luminance level independently of the viewing direction. The angular-dependent luminance uniformity is calculated as the ratio of maximum luminance to minimum luminance in the specified measurement areas.

- Test pattern : 80% white pattern

- Test point : 2-point

- Test distance : D * 1.5 = 70.52㎝

- Test method : LR = ((L TB = ((L

FIG. 11 Luminance Uniformity angular dependence

max.+30deg.

max.+15deg.

/ L

min. +30deg.

min. +15deg.

) + (L

)

max. -30deg.

/ L

min. -30deg.

)) / 2

LM185WH1

< Luminance uniformity - angular dependence measuring point >

www.jxlcd.com

7. Gray scale specification

Table 11. Gray scale

L0

L31

L63

L95

L127

L159

L191

L223

L255

H

D

V/2

V

V/2

Luminance [%] (Typ)Gray level

L

H/10

0.11

1.17

4.80

11.10

20.53

34.44

54.53

78.66

100

T

C

B

H/10

V/10

R

V/10

Ver. 1.0 Sep., 10, 2008

24 / 32

LM185WH1

22

)''()''( BABA vvuu  

Liquid Crystal Display

Product Specification

Notes :

8. Color grayscale linearity , Δu’v’ is defined as

Where indices A and B are the two gray levels found to have the largest color differences between them.

i.e. get the largest Δu’ and Δv’ of each 6pairs of u’ and v’ and calculate Δu’v’ .

Test pattern : 100% full white pattern with a test pattern as shown FIG.12 Squares of 40mm by 40mm in size, filled with 255, 225, 195, 165, 135 and 105 grayscale steps should be arranged in the center of the screen.

Test method : First gray step : Move a square of 255 gray level should be moved into the center of the screen and measure luminance and u’ and v’ coordinates.

Next gray step : Move a 255 gray square into the center and measure both luminance and u’ and v’ coordinates.

www.jxlcd.com

The same procedure shall then be repeated for gray steps 195, 165, 135 and 105.

www.jxlcd.com

FIG. 12 Color grayscale linearity

40mm

Ver. 1.0 Sep., 10, 2008

25 / 32

LM185WH1

Liquid Crystal Display

Product Specification

5. Mechanical characteristics

The contents provide general mechanical characteristics. In addition the figures in the next page are detailed mechanical drawing of the LCD.

Table 12. Mechanical characteristics

430.4 mmHorizontal

Outline dimension

Bezel area

Active display area

1550 g (Typ.) 1650 g (Max)Weight

Surface treatment

Notes : Please refer to a mechanic drawing in terms of tolerance at the next page.

www.jxlcd.com

Hard coating(3H) Anti-glare treatment of the front polarizer

254.6 mmVertical

13.0 mmDepth

413.4 mmHorizontal

234.0 mmVertical

409.800 mmHorizontal

230.400 mmVertical

Ver. 1.0 Sep., 10, 2008

26 / 32

LM185WH1

Liquid Crystal Display

Product Specification

www.jxlcd.com

Ver. 1.0 Sep., 10, 2008

27 / 32

LM185WH1

Liquid Crystal Display

Product Specification

www.jxlcd.com

Ver. 1.0 Sep., 10, 2008

28 / 32

Product Specification

6. Reliability

Table 13. Environment test conditions

No Test Item Condition

Ta= 60°C 240hrsHigh temperature storage test1

Ta= -20°C 240hrsLow temperature storage test2

Ta= 50°C 50%RH 240hrsHigh temperature operation test3

Ta= 0°C 240hrsLow temperature operation test4

Wave form : random

5

6

7

Vibration test (non-operating)

Shock test (non-operating)

Altitude operating storage / shipment

Vibration level : 1.0GRMS Bandwidth : 10-300Hz Duration : X,Y,Z, 30 min One time each direction Shock level : 120G Waveform : half sine wave, 2msec Direction : ±X, ±Y, ±Z One time each direction

0 - 10,000 feet(3,048m) 0 - 40,000 feet(12,192m)

LM185WH1

Liquid Crystal Display

{ Result evaluation criteria } There should be no change which might affect the practical display function when the display quality test is conducted under normal operating condition.

www.jxlcd.com

Ver. 1.0 Sep., 10, 2008

29 / 32

LM185WH1

Liquid Crystal Display

Product Specification

7. International standards

7-1. Safety

a) UL 60950-1:2003, First Edition, Underwriters Laboratories, Inc.,

Standard for Safety of Information Technology Equipment.

b) CAN/CSA C22.2, No. 60950-1-03 1st Ed. April 1, 2003, Canadian Standards Association, Standard for Safety of Information Technology Equipment.

c) EN 60950-1:2001, First Edition,

European Committee for Electro-technical Standardization(CENELEC) European Standard for Safety of Information Technology Equipment. d) RoHS, Directive 2002/95/EC of the European Parliament and of the council of 27 January 2003

7-2. EMC

a) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from LowVoltage Electrical and Electrical Equipment in the Range of 9kHZ to 40GHz. “American National Standards Institute(ANSI),1992

b) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment.“ International Special Committee on Radio Interference. c) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology Equipment.“ European Committee for Electro-technical Standardization.(CENELEC), 1998 ( Including A1: 2000 )

www.jxlcd.com

Ver. 1.0 Sep., 10, 2008

30 / 32

Product Specification

8. Packing

8-1. Designation of lot mark

a) Lot mark

A B C D E F G H I J K L M

A,B,C : Size (Inch) D : Year E : Month F ~ M : Serial No.

Note:

1. Year

LM185WH1

Liquid Crystal Display

Year

Mark

2. Month

Month

Mark

www.jxlcd.com

b) Location of lot mark

Serial No. is printed on the label. The label is attached to the backside of the LCD module. This is subject to change without prior notice.

200320022001

200452005

321

4

Apr5May

4

2006720078200892009

6

Jun7Jul8Aug9Sep

6

2010

0

Oct

A

8-2. Packing form

a) Package quantity in one box : 10 pcs b) Box size : 540 mm X 312 mm X 315 mm

Nov

B

DecMarFebJan

C321

Ver. 1.0 Sep., 10, 2008

31 / 32

LM185WH1

Liquid Crystal Display

Product Specification

9. Precautions

Please pay attention to the followings when you use this TFT LCD module.

9-1. Mounting Precautions

(1) You must mount a module using holes arranged in four corners or four sides. (2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the Module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer. Transparent protective plate should have sufficient strength in order to the resist external force. (4) You should adopt radiation structure to satisfy the temperature specification. (5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the surface of polarizer for bare hand or greasy cloth. (Some cosmetics are detrimental to the polarizer.) (7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes deformations and color fading. (9) Do not open the case because inside circuits do not have sufficient strength.

9-2. Operating precautions

www.jxlcd.com

(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage : V=±200mV(Over and under shoot voltage) (2) Response time depends on the temperature.(In lower temperature, it becomes longer.) (3) Brightness depends on the temperature. (In lower temperature, it becomes lower.) And in lower temperature, response time(required time that brightness is stable after turned on) becomes longer. (4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur. (5) When fixed patterns are displayed for a long time, remnant image is likely to occur. (6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be done by system manufacturers. Grounding and shielding methods may be important to minimized the interference. (7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM can not be operated its full characteristics perfectly. (8) A screw which is fastened up the steels should be a machine screw (if not, it causes metal foreign material and deal LCM a fatal blow) (9) Please do not set LCD on its edge.

Ver. 1.0 Sep., 10, 2008

32 / 32

LM185WH1

Liquid Crystal Display

Product Specification

9-3. Electrostatic discharge control

Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.

9-4. Precautions for strong light exposure

Strong light exposure causes degradation of polarizer and color filter.

9-5. Storage

When storing modules as spares for a long time, the following precautions are necessary.

(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5°C and 35°C at normal humidity. (2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped.

9-6. Handling precautions for protection film

(1) The protection film is attached to the bezel with a small masking tape. When the protection film is peeled off, static electricity is generated between the film and polarizer. This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) When the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the bezel after the protection film is peeled off. (3) You can remove the glue easily. When the glue remains on the bezel surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane.

www.jxlcd.com

Ver. 1.0 Sep., 10, 2008

33 / 32