Datasheet LK112M80TR, LK112M60TR, LK112M55TR, LK112M50TR, LK112M49TR Datasheet (SGS Thomson Microelectronics)
...Page 1
1/12June 2003
■ OUTPUT CURRENT UP TO 150mA
■ LOW DROPOUT VOLTAGE (350mV AT
I
OUT
=150mA)
■ VERY LOW QUIESCENT CURRENT: 0.1µA
IN OFF MODE AND MAX 250µA IN ON
MODE AT I
OUT
=0mA
■ LOW OUTPUT NOISE: TYP 30µV AT
I
OUT
=60mA AND 10Hz<f<80KHz
■ WIDE RANGE OF OUTPUT VOLTGAES
■ INTERNAL CURRENT AND THERMAL LIMIT
DESCRIPTION
The LK112 is a low dropout linear regulator with a
built in electronic switch. The internal switch can
be controlled by TTL or CMOS logic levels. The
device is ON state when the control pin is pulled to
a logic high level. An external capacitor can be
used connected to the noise bypass pin to lower
the output noise level to 30µV
rms
. An internal PNP
pass transistor is used t o achieve a low dropout
voltage.
The LK112 has a very low quiescent current in ON
MODE while in OFF MODE the Iq is reduced
down to 100nA max. The internal thermal
shutdown circuitry limits the juntion temperature to
below 150°C. The load current is internally
monitored and the device will shutdown in the
presence of a short circuit or overcurrent condition
at the output.
LK112
SERIES
LOW NOISE LOW DROP VOLTAGE REGULATOR
WITH SH UTDOWN FUNCTI ON
SCHEMATIC DIAGRAM
SOT23-5L
Page 2
LK112 SERIES
2/12
ABSOLUTE MAXIMUM RATINGS
THERMAL DATA
CONNECTION DIAGRAM (top view) PIN DESCRIPTION
Symbol Parameter² Value Unit
V
I
DC Input Voltage
16 V
V
SHDN
Shutdown Input Voltage
16 V
I
O
Output Current
Internally limited
T
stg
Storage Temperature Range
-55 to +150 °C
T
op
Operating Junction Temperature Range
-30 to +125 °C
Symbol Parameter SOT23-5L Unit
R
thj-case
Thermal Resistance Junction-case
81 °C/W
R
thj-amb
Thermal Resistance Junction-ambient
255 °C/W
SOT23-5L
Pin N° Symbol Name and Function
1 SHDN Shutdown Input: Disables the
regulator when is connected to GND
or to positive voltage less than 0.6V
2 GND Ground Pin: Internally connected to
the die attach flag to decrease the
total thermal resistance and increase
the package ability to dissipate
power.
3 Bypass Bypass Pin: Bypass with 0.1µF to
improve the Vref thermal noise
performances.
4 OU T Output Port
5 IN Input Port
Page 3
LK112 SERIES
3/12
ELECTRICAL CHARACTERISTICS FOR LK112 (Tj = 25°C, VIN=V
OUT
+1V (see Note 1), I
OUT
=0mA,
V
SHDN
=1.8V, CI = 1 µF, CO = 2.2µ F, C
BYPASS
= 0.1µF unless otherwise specified)
Note 1: fo r version with output volt age less than 2V VIN=2.4V
Note 2: only for version with output voltage more than 2.1V
Symbol Parameter Test Conditions Min. Typ. Max. Unit
I
d
Quiescent Current ON MODE (except I
SHDN
) 175 250 µA
OFF MODE V
I
= 8V V
SHDN
= 0V 0 0.1 µA
V
O
Output Voltage IO = 30mA (see table)
∆V
O
Line Regulation VI = VO+1V to VO+6V, VO ≤ 5.6V 0.7 20 mV
V
I
= VO+1V to VO+6V, VO > 5.6V 0.8 40 mV
∆V
O
Load Regulation IO = 1 to 60mA 15 30 mV
I
O
= 1 to 150mA 25 90 mV
V
d
Dropout Voltage IO = 60 mA (see Note 2) 0.17 0.24 V
I
O
= 150 mA (see Note 2) 0.29 0.35 V
I
O
Output Current Limit 150 mA
SVR Supply Voltage Rejection V
I
= VO+1.5V C
BYP
= 0.1µF
C
O
= 10µF f = 400Hz IO = 30mA
55 dB
eN Output Noise Voltage B= 10Hz to 80KHz C
BYP
= 0.1µF
C
O
= 10µFVI = VO+1.5V,IO = 60mA
30 µVrms
I
SHDN
Shutdown Input Current V
SHDN
= 1.8V Output ON 12 35 µA
V
SHDN
Shutdown Input Logic Output ON
Output OFF
1.8
0.6
V
V
∆V
O/Tj
Output Voltage
Temperature Coefficient
IO = 10mA 0.09 mV/°C
Page 4
LK112 SERIES
4/12
ORDERING NUMBERS AND OUTPUT VOLTAGE
(*) Avai l abl e on request
Part Number Output Voltage
V
OUT
Min V
OUT
Max
Test Voltage
LK112M13TR 1.3V 1.24V 1.36V 2.4V
LK112M14TR (*) 1.4V 1.34V 1.46V 2.4V
LK112M15TR 1.5V 1.44V 1.56V 2.4V
LK112M16TR 1.6V 1.54V 1.66V 2.4V
LK112M17TR 1.7V 1.64V 1.76V 2.4V
LK112M18TR 1.8V 1.74V 1.86V 2.4V
LK112M19TR (*) 1.9V 1.84V 1.96V 2.4V
LK112M20TR (*) 2.0V 1.94V 2.06V 3.0V
LK112M21TR 2.1V 2.04V 2.16V 3.1V
LK112M22TR (*) 2.2V 2.14V 2.26V 3.2V
LK112M23TR (*) 2.3V 2.24V 2.36V 3.3V
LK112M24TR (*) 2.4V 2.34V 2.46V 3.4V
LK112M25TR 2.5V 2.44V 2.56V 3.5V
LK112M26TR (*) 2.6V 2.54V 2.66V 3.6V
LK112M27TR (*) 2.7V 2.64V 2.76V 3.7V
LK112M28TR 2.8V 2.74V 2.86V 3.8V
LK112M29TR (*) 2.9V 2.84V 2.96V 3.9V
LK112M30TR 3.0V 2.94V 3.06V 4.0V
LK112M31TR (*) 3.1V 3.04V 3.16V 4.1V
LK112M32TR 3.2V 3.14V 3.26V 4.2V
LK112M33TR 3.3V 3.24V 3.36V 4.3V
LK112M34TR (*) 3.4V 3.335V 3.465V 4.4V
LK112M35TR (*) 3.5V 3.435V 3.565V 4.5V
LK112M36TR 3.6V 3.535V 3.655V 4.6V
LK112M37TR (*) 3.7V 3.630V 3.770V 4.7V
LK112M38TR 3.8V 3.725V 3.875V 4.8V
LK112M39TR (*) 3.9V 3.825V 3.975V 4.9V
LK112M40TR 4.0V 3.920V 4.080V 5.0V
LK112M41TR (*) 4.1V 4.020V 4.180V 5.1V
LK112M42TR (*) 4.2V 4.120V 4.280V 5.2V
LK112M43TR (*) 4.3V 4.215V 4.385V 5.3V
LK112M44TR (*) 4.4V 4.315V 4.485V 5.4V
LK112M45TR (*) 4.5V 4.410V 4.590V 5.5V
LK112M46TR (*) 4.6V 4.510V 4.690V 5.6V
LK112M47TR 4.7V 4.605V 4.795V 5.7V
LK112M48TR (*) 4.8V 4.705V 4.895V 5.8V
LK112M49TR (*) 4.9V 4.800V 5.000V 5.9V
LK112M50TR 5.0V 4.900V 5.100V 6.0V
LK112M55TR (*) 5.5V 5.390V 5.610V 6.5V
LK112M60TR 6.0V 5.880V 6.120V 7.0V
LK112M80TR 8.0V 7.840V 8.160V 9.0V
Page 5
LK112 SERIES
5/12
TYPICAL CHARACTERISTICS (unless otherwise specified Tj = 25°C, CI=1µF, CO=2.2µF, C
BYP
=100nF)
Figure 1 : Output Voltage vs Temp erature
Figure 2 : Output Voltage vs Temp erature
Figure 3 : Line Regulation vs Temperature
Figure 4 : Load Regulation vs Temperature
Figure 5 : Dropout Voltage vs Temperature
Figure 6 : Short Circuit Currennt vs Dropout
Voltage
Page 6
LK112 SERIES
6/12
Figure 7 : Output Voltage vs Input Voltage
Figure 8 : Shutdown Voltage vs Temperature
Figure 9 : Shutdown Current vs Shutdown
Voltage
Figure 10 : Supply Voltage Rejection vs
Temperature
Figure 11 : Supply Voltage Rejection vs Output
Current
Figure 12 : Supply Voltage Rejection vs
Frequency
Page 7
LK112 SERIES
7/12
Figure 13 : Supply Voltage Rejection vs
Temperature
Figure 14 : Quiescent Current vs Temperature
Figure 15 : Quiescent Current vs Input Voltage
Figure 16 : Quiescent Current vs Shutdown
Voltage
Figure 17 : Quiescent Current vs Output Current
Figure 18 : Reverse Current vs Reverse Voltage
Page 8
LK112 SERIES
8/12
Figure 19 : Stability
Figure 20 : Spectrum Noise
Figure 21 : Start-up Transient
Figure 22 : Start-up Transient
Figure 23 : Line Transient
Figure 24 : Line Transient
V
I
=3.5V,
V
O
=2.5V,
V
SHDN
= 0 to 1.8V,
R
L
=2.5KΩ,
C
I
=1µF,
C
O
=4.7µF, CBY=10nF
V
I
=3.5V,
V
O
=2.5V,
V
SHDN
= 0 to 1.8V,
R
L
=68Ω,
C
I
=1µF,
C
O
=4.7µF,
C
BY
=100nF
V
I
=3.5 to 4.5V,
V
O
=2.5V,
V
SHDN
=1.8V,
I
O
=30mA, No
C
I
,
C
O
=10µF,
C
BY
=100nF, ts=tf=2µs
V
I
=3.5 to 4.5V,
V
O
=2.5V,
V
SHDN
=1.8V,
I
O
=30mA, No
C
I
,
C
O
=10µF,
C
BY
=10nF, ts=tf=2µs
Page 9
LK112 SERIES
9/12
Figure 25 : Line Transient
Figure 26 : Load Transient
Figure 27 : Load Transient
Figure 28 : Load Transient
V
I
=3.5 to 4.5V,
V
O
=2.5V,
V
SHDN
=1.8V,
I
O
=30mA, No
C
I
,
C
O
=1µF,
C
BY
=1nF, ts=tf=2µs
V
I
=3.5 V,
V
O
=2.5V,
V
SHDN
=1.8V,
I
O
=50 to
100mA, C
I
=1µF,
C
O
=2.2µF, CBY=10nF, ts=tf=250ns
V
I
=3.5V,
V
O
=2.5V,
V
SHDN
=1.8V,
I
O
=50 to
100mA, CI1µF
,
C
O
=10µF, CBY=100nF, ts=tf=250ns
V
I
=4.8 V,
V
O
=3.8V,
V
SHDN
=1.8V,
I
O
=50 to
100mA, C
I
=1µF,
C
O
=2.2µF, CBY=10nF, ts=tf=250ns
Page 10
LK112 SERIES
10/12
DIM.
mm. mils
MIN. TYP MAX. MIN. TYP. MAX.
A 0.90 1.45 35.4 57.1
A1 0.00 0.10 0.0 3.9
A2 0.90 1.30 35.4 51.2
b 0.35 0.50 13.7 19.7
C 0.09 0.20 3.5 7.8
D 2.80 3.00 110.2 118.1
E 1.50 1.75 59.0 68.8
e0.95 37.4
H 2.60 3.00 102.3 118.1
L 0.10 0.60 3.9 23.6
SOT23-5L MECHANICAL DATA
7049676C
.
Page 11
LK112 SERIES
11/12
DIM.
mm. inch
MIN. TYP MAX. MIN. TYP. MAX.
A 180 7.086
C 12.8 13.0 13.2 0.504 0.512 0.519
D 20.2 0.795
N 60 2.362
T 14.4 0.567
Ao 3.13 3.23 3.33 0.123 0.127 0.131
Bo 3.07 3.17 3.27 0.120 0.124 0.128
Ko 1.27 1.37 1.47 0.050 0.054 0.0.58
Po 3.9 4.0 4.1 0.153 0.157 0.161
P 3.9 4.0 4.1 0.153 0.157 0.161
Tape & Reel SOT23-xL MECHANICAL DATA
Page 12
LK112 SERIES
12/12
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the
consequences of use o f suc h inf ormat ion n or f or an y infr ingeme nt of paten ts or oth er ri gh ts of third part ies whic h may resul t f rom
its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications
mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information
previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or
systems without express written approval of STMicroelectronics.
© The ST logo is a registered trademark of STMicroelectronics
© 2003 STMicroelectronics - Printed in Italy - All Rights Reserved
STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom - United States.
© http://www.st.com
Loading...