Page 1
Terminal Code : LI (φ30,φ35)
The standard design has no plastic disc.
(View from Solder side)
1 3 42 6 7 8 9 10 13125 18171611 1514
Please refer to "Product code guide (snap-in type)"
LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
Upgrade!
LHSSeries
The lower temperature range of the category temperature range has been expended.
・
For solar power generation
・
Endurance with ripple current : 5,000 hours at 105
・
Rated voltage range : 450 to 500V
・
For inverter control, switching power supplies
・
Non solvent resistant type
・
RoHS2 Compliant
・
SPECIFICATIONS
◆
Items Characteristics
Category
Temperature Range
Rated Voltage Range
Capacitance Tolerance
Leakage Current
Dissipation Factor
(tanδ)
Low Temperature
Characteristics
(Max. Impedance Ratio)
Endurance
Shelf Life
-40 to +105
450 to 500V
±
I≦3 CV
Where, I : Max. leakage current (µA), C : Nominal capacitance (µF), V : Rated voltage (V) (at 20℃ after 5 minutes)
Rated voltage (V
Rated voltage (Vdc) 450 to 500V
Z(-25℃)/Z(+20℃) 8
(at 120Hz)
The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjected to DC voltage with the rated
ripple current is applied (the peak voltage shall not exceed the rated voltage) for 5,000 hours at 105℃.
Capacitance change
D.F. (tanδ)
Leakage current
The following specifications shall be satisfied when the capacitors are restored to 20℃ after exposing them for 1,000 hours at 105℃ without
voltage applied. Before the measurement, the capacitor shall be preconditioned by applying voltage according to Item 4.1 of JIS C 5101-4.
Capacitance change
D.F. (tanδ)
Leakage current
℃
20% (M) (at 20℃, 120Hz)
dc
) 450 to 500V
dc
℃
(at 20℃, 120Hz)tanδ (Max.) 0.20
20% of the initial value
≦±
200% of the initial specified value (475, 500V
≦
The initial specified value
≦
15% of the initial value
≦±
150% of the initial specified value
≦
The initial specified value
≦
LHS
Downsizing
LXS
Longer life
KMS
: ≦ 250%)
dc
Long life snap-ins, 105℃
DIMENSIONS [mm]
◆
●
Terminal Code : VS (φ22 to φ35) : Standard
Sleeve (PET : Brown)
φD+1max.
Vent
PART NUMBERING SYSTEM
◆
L±2.5
E L H S V S N SM
4.0±0.5
PC board pin-out
Negative mark
Capacitance code (ex. 100µF:101, 330µF:331)
(View from Solder side)
Voltage code (ex. 450V:451, 475V:4H1)
10
2-φ2
Supplement code
Capacitance tolerance code
Dummy terminal code
Terminal code(VS, LI)
Vent
Size code
Series code
Category
●
Sleeve (PET : Brown)
φD+1max.
L±2.5
Negative mark
4.5±1
PC board pin-out
2-1.2×6
4.2±0.5
5±0.5
14.2±1
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001V 2021
Page 2
LARGE CAPACITANCE ALUMINUM ELECTROLYTIC CAPACITORS
LHSSeries
STANDARD RATINGS
◆
WV
(V
450
)
dc
Case size
Cap
(µF)
100 22×25 0.20 0.71 ELHS451VSN101MP25S
120 22×30 0.20 0.81 ELHS451VSN121MP30S 180 30×30 0.20 1.11 ELHS4H1VSN181MR30S
150 22×35 0.20 0.93 ELHS451VSN151MP35S 180 35×25 0.20 1.08 ELHS4H1VSN181MA25S
150 25.4×25 0.20 0.93 ELHS451VSN151MQ25S 220 30×35 0.20 1.26 ELHS4H1VSN221MR35S
180 22×40 0.20 1.04 ELHS451VSN181MP40S 270 30×40 0.20 1.44 ELHS4H1VSN271MR40S
180 25.4×30 0.20 1.05 ELHS451VSN181MQ30S 270 35×30 0.20 1.35 ELHS4H1VSN271MA30S
220 22×45 0.20 1.17 ELHS451VSN221MP45S 330 30×45 0.20 1.63 ELHS4H1VSN331MR45S
220 25.4×35 0.20 1.21 ELHS451VSN221MQ35S 330 35×35 0.20 1.51 ELHS4H1VSN331MA35S
220 30×25 0.20 1.15 ELHS451VSN221MR25S 390 30×50 0.20 1.80 ELHS4H1VSN391MR50S
270 22×50 0.20 1.33 ELHS451VSN271MP50S 390 35×40 0.20 1.70 ELHS4H1VSN391MA40S
270 25.4×40 0.20 1.36 ELHS451VSN271MQ40S 470 30×60 0.20 2.05 ELHS4H1VSN471MR60S
270 30×30 0.20 1.29 ELHS451VSN271MR30S 470 35×45 0.20 1.91 ELHS4H1VSN471MA45S
270 35×25 0.20 1.25 ELHS451VSN271MA25S 470 35×50 0.20 1.95 ELHS4H1VSN471MA50S
330 22×60 0.20 1.54 ELHS451VSN331MP60S 560 35×60 0.20 2.21 ELHS4H1VSN561MA60S
330 25.4×45 0.20 1.54 ELHS451VSN331MQ45S
330 25.4×50 0.20 1.56 ELHS451VSN331MQ50S 150 30×30 0.20 1.02 ELHS501VSN151MR30S
330 30×35 0.20 1.46 ELHS451VSN331MR35S 150 35×25 0.20 0.99 ELHS501VSN151MA25S
330 35×30 0.20 1.41 ELHS451VSN331MA30S 180 30×35 0.20 1.14 ELHS501VSN181MR35S
390 25.4×60 0.20 1.74 ELHS451VSN391MQ60S 220 30×40 0.20 1.30 ELHS501VSN221MR40S
390 30×40 0.20 1.63 ELHS451VSN391MR40S 220 35×30 0.20 1.22 ELHS501VSN221MA30S
470 30×45 0.20 1.84 ELHS451VSN471MR45S 270 30×45 0.20 1.47 ELHS501VSN271MR45S
470 30×50 0.20 1.87 ELHS451VSN471MR50S 270 35×35 0.20 1.37 ELHS501VSN271MA35S
470 35×35 0.20 1.71 ELHS451VSN471MA35S 330 30×50 0.20 1.66 ELHS501VSN331MR50S
560 35×40 0.20 1.95 ELHS451VSN561MA40S 330 35×40 0.20 1.57 ELHS501VSN331MA40S
560 35×45 0.20 1.99 ELHS451VSN561MA45S 390 30×60 0.20 1.87 ELHS501VSN391MR60S
680 30×60 0.20 2.33 ELHS451VSN681MR60S
680 35×50 0.20 2.22 ELHS451VSN681MA50S 470 35×50 0.20 1.95 ELHS501VSN471MA50S
820 35×60 0.20 2.52 ELHS451VSN821MA60S 560 35×60 0.20 2.21 ELHS501VSN561MA60S
φD×
L(mm)
tan
Rated ripple
δ
(Arms/
105℃, 120Hz)
current
Part No.
Long life snap-ins, 105℃
WV
(V
475
500
)
dc
Case size
Cap
(µF)
150 30×25 0.20 1.01 ELHS4H1VSN151MR25S
120 30×25 0.20 0.90 ELHS501VSN121MR25S
390 35×45 0.20 1.74 ELHS501VSN391MA45S
φD×
L(mm)
tan
Rated ripple
δ
(Arms/
105℃, 120Hz)
current
Part No.
RATED RIPPLE CURRENT MULTIPLIERS
◆
Frequency Multipliers
・
Frequency(Hz) 50 120 300 1k 10k 50k
450V
dc
475, 500V
0.77 1.00 1.16 1.30 1.41 1.43
0.70 1.00 1.16 1.30 1.41 1.43
dc
The endurance of capacitors is reduced with internal heating produced by ripple current at the rate of halving the lifetime with every 5℃ rise.
When long life performance is required in actual use, the rms ripple current has to be reduced.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
CAT. No. E1001V 2021
Loading...