Page 1
Radial Lead Aluminum Electrolytic Capacitors
Safety vent (Ф8up)
ELE Low Leakage Current SERIES
EGH seri es are l arg e siz e cap acitors hav e “s elf -standi ng” ter min als and c an b e direc tly s old ered to pri nt ed circ uit b oards with out any fi xing
clamps or ad h esi v e ag ents . The y are eas ily fixed to printed circ ui t boards due the special l y des ig n ed t er mi nals.
Low leakag e c ur r ent s eri es wit h 5m m height.
Design ed for use in light weig ht an d p ort ab l e equ ip m ent .
Specifications
Item Characteristics
Operating temperature range -40~+85°C
Voltage range 4~50 V.DC
Nominal cap. range 0.1~100 uF
Capacitance tolerance -20%~+20% (at 120Hz, 20 °C)
Leaka ge current (max) I=0.002CV or 4 (uA) whichever is greater (after 2 min)
W V 4 6.3 10 16 25 35 50 Dissipation Factor (tg δ)
(at 120Hz, /+20°C) (max)
Low temp. impedance
Stability at 120Hz
High temp. Load test
(after application of the rated
voltage for 1000 hou rs at 85°C )
High temp. Non-Load test
Note: Some cleaning solvents may adversely affect the capacitors. Consult us about the suitable type of cleaning solvents to be used.
tanδ 0.35 0.24 0.20
W.V. 4 6.3 10 16 25 35 50
Z(-25°C)/Z(+20°C) 7 5 3 2 2 2 2
Z(-40°C)/Z(+20°C) 15 10 8 6 4 3 3
Leakage current Less than specified value
Capacitance change Within ±20% of in iti al v al u e
tanδ Less than 200% of speci fied value
After st orage for 500 hours at 85°C with no v oltage appli ed, voltag e treatment of JIS-C -5102
article 4-4 is to be given and then measurement shall be made, at which time requirements
specified in the table “High temperature loading” can be met.
0.16 0.14 0.12 0.10
Drawing
Ф
Insulating Sleeve
max
α
D+
Ф
*Ф6.3 is avai l abl e b y R equ es t
d±0 .05 T i n ne d coppe r- ply wire
15min L + β max
4min
p±0.5
Φ
D 4 5 6.3
P 1.5 2.0 2.5
Φ
d
β
1.0
α
0.5
Unit: (mm)
0.45
www.kingcap.com
1/2
Page 2
Radial Lead Aluminum Electrolytic Capacitors
Dimension & Maximum Permissible Ripple Current mA (rms) at 85°C, 120Hz
4 6.3 10 16 25 35 50 WV(V)
uF
0.1
Φ
(mm)
D×L
Ripple
current
(mArms)
Φ
(mm)
D×L
Ripple
current
(mArms)
Φ
D×L
(mm)
Ripple
current
(mArms)
Φ
D×L
(mm)
Ripple
current
(mArms)
4×5 3.9
Φ
D×L
(mm)
Ripple
current
(mArms)
Φ
D×L
(mm)
Ripple
current
(mArms)
Φ
D×L
(mm)
Ripple
current
(mArms)
0.15
0.22
0.33
0.47
0.68
1.0
1.5
2.2
3.3
4.7
6.8
10
15
22
33
47
4×5 4.8
4×5 5.9
4×5 7.2
4×5 8.6
4×5 10
4×5 12
4×5 15
4×5 18
4×5 22
4×5 25 5×5 31
4×5 27 5×5 34 6.3×5
4×5 61 5×5 39 5×5 42 6.3×5
4×5 34 5×5 44 6.3×5
4×5 38 5×5 48 6.3×5
5×5 44 5×5 54 6.3×5
5×5 53 6.3×5
74 6.3×5
67 6.3×5
81
62 6.3×5
76
54 6.3×5
66
59
43
52
68
100
6.3×5
6.3×5
73 6.3×5
89
89
www.kingcap.com
2/2
Loading...