the capacitor or leakage of electrolyte. Where the polarity in a
注意事项及指引(Precautions & Guidelines)
关于铝电解电容
For Aluminum Electrolytic Capacitors
1. 极性
铝电解电容器是一般是有极性的,极性反接是造成铝
电解电容器短路损坏及漏液的原因,因此在无法辨识
电气回路上之极性或使用于有极性变换设计之回路
时,请选用无极性电解电容器。
2. 过载
请勿连续施加过载电压。当电压过载时电解电容器的
漏电流会急速增加,所以电解电容器之工作电压不应
超过额定值。
3. 使用温度和寿命
电解电容器之使用温度请勿超出最高使用温度之设
定范围。电解电容器的寿命取决于使用温度,一般来
说当电解电容器之使用温度降低 10℃时,其寿命将
增为两倍,因此电解电容器应尽可能在较低温度下使
用。
4. 防爆孔
有防爆孔设计之电解电容器其使用时防爆孔侧应与
其它机构保持最少 3mm 以上空间距离,如此条件不
能满足的话,防爆孔将无法正常运作。
5. 纹波电流
请勿施加超过额定最高纹波电流容许值以上之纹波
电流。施加过大纹波电流将使电解电容器的内温异常
上升,引起电解电容器电气特性劣化及破损。如有需
要施加额定值以上之纹波电流等要求时,请咨询敝厂
人员。
6. 充放电
经常及快速的充放电将使电解电容器之内温异常上
升,使漏电流增加、容量降低,有时还会造成产品之
损坏,如对充放电有特殊要求时请咨询敝厂人员。
7. 电解电容器的储存
当电解电容器经过长时间之放置后,通常其漏电流有
增大之倾向。因此在使用经过长时间放置后的电解电
容器以前,如储存时间长于 6 个月以上时,请串排
1KΩ之保护电阻后,使其持续负载定额工作电压 30
分钟。另外电解电容器应储存于常温及常湿之环境
下。
1.Polarity
Regular electrolytic Capacitor has polarity.
Reverse voltage causes short circuit breakage of
circuit sometimes reversed or unknown, a bi-polar capacitor
should be used.
2.Overvoltage
Do not apply overvoltage continuously.
When overvoltage is applied to the capacitor, leakage
current increase drastically.
Applied working voltage to capacitors should not
exceed the rated working voltage of capacitor.
3.Operating temperature and life:
Do not use the capacitor over the max
operating temperature.
Life time of the capacitor depends on the temperature.
Generally, life time is doubled by decreasing
each temperature 10Ċ.
Use temperature as low as possible.
4.Vent
It is recommended at least 3mm of space
around the vent.
If such space is not provided, the vent will not operate
completely.
5.Ripple current
Do not apply a ripple current exceeding the
rated maximum ripple current.
Applying too much ripple current to the
capacitor causes great heat generation, invites
deterioration of properties of cases breakage.
Please consult factory if ripple current exceeds
the specified limit.
6.Charge and discharging
Frequent and quick charge/discharge generates heat
inside the capacitor, causing increase of leakage
current , decrease of capacitance , or breakage
occasionally.
7.Storage
When the capacitor is stored for a long time
without applying voltage, leakage current tends to increase.
This returns to normal by applying the rated voltage to the
capacitor before use.
It is recommended to apply D.C. working
voltage to the capacitor for 30 minutes through 1K of
protective series resistor, if it is stored for more than 6
months.
8.Soldering
Improper soldering may shrink or break the insulating
sleeve and/or damage the internal element as terminals and
lead wires conduct heat into the capacitor.
Avoid too high a soldering temperature and/or too
long a soldering time.
9
.Mechanical stress on the lead wire and the terminal
Do not apply excessive force to the lead wire and the
terminal.
Do not move the capacitor after soldering to the PC board,
not carry the PC hoard by picking up the capacitor. For
their strength, refer to JIS C-5141 and C-5102.
1
0.Cleaning of boards after soldering
If the capacitor is cleaned in halogenated solvent fo organic
removing solder flux solvent, the solvent
the inside of capacitor, and may generate corrosion..
11.Sleeve material
The standard sleeve matenal is polyvinyl-chloride.
If exposed to xylene, toluene, etc, and then subjected to
high heat, the sleeve may crack. This sleeve is not nsulating
material.
12.Dumicon’s Products meet quality standards specified by
JIS-C5141W and with the reliability requirements refer to
JIS-C-5102.
13.None of ozone depleting chemicals (ODC) under the
Montreal Protocol is used in manufacturing process of
Jinhua Xinlong Electronic Industrial CO., Ltd.
12/87
Page 13
120HZ
LV
Series
10
C
athode
Voltag
e
A±0.2
B
P
LV 系列 85(℃ LV Series 85)℃
特性(Features)
★ 85 ℃ 标准品,直径¢4〜 ¢10mm(85℃ standard, case diameter ¢4~¢10mm)
★ 可用回流焊(Reflow soldering is available)
★ 可用于高密度安装(Available for high density mounting)
★ 对于详细规格,请参阅附页(
★ 符合RoHS(
RoHS Compliant)
For detail specifications, please refer to the attached)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+85℃
额定工作电压(Rated Voltage Range)
静电容量范围(Capacitance Range) 0.1-1500 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损 耗 角正 切 ( Dissipation Factor)( tanδ)
+20℃
I≤0.01CV or 3(uA) After 2 minutes with rated working voltage applied
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温度:+85℃(Ambient temperature:+85℃ )
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±25%(Capacitance change: within±25% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: Not more than 200% of specified value)
漏电流:小于等于规格值(Leakage current : Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+85℃(Ambient temperature:+85℃ )
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20 :Same limits as Loa℃d
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
application of DC working voltage for 30 minutes)
shall be kept on the hot plate maintained at 250Ċfor 30 seconds. After removing form the hot plate and
restored at room temperature, they meet the characteristic requirements listed under.)
漏电流(Leakage current) 小于规定值(Less than specified)
容量变化(value Capacitance change)
损耗角(tan δ) 小于规定值(Less than specified)
容量与频率测试(Multiplier for Ripple Current vs. Frequency)
纹波电流(A),在85 120HZ ℃(Ripple Current ( A, rms ) at 85℃ 120Hz)
25
(32
5x5.5
6.3x5.5
5x5.5
6.3x5.5
6.3x5.5 60
6.3x7.7
8x6.5
8x10.5 300 10x10.5 400 10x10.5 450
40
40
46
54
150
160
35
(44
5x5.5
6.3x5.5
6.3x5.5 58
6.3x5.5
8x6.5
6.3x7.7
8x10.5
45
48
65
115
250
280
6.3x7
8x6.5
6.3x7.7
8x6.5
6.3x7.7
8x6.5
8x10.5 300
(63)
50
75
80
188
200
225
240
14/87
Page 15
120HZ
EV
Series
D
10
C
athode
Voltage
C
EV 系列 105(EV Series 105)℃℃
特性(Features)
★ 大小尺寸的长寿命贴片电容(Chip type long life capacitance in large case sizes)
★ 105 1000H℃寿命(Chip type with load life of 1000 hours at 105℃)
★ 专为表面安装高密度印刷电路板(Designed for surface mounting on high density PC boa)
★ 适用于使用自动插入机用载带(Applicable to automatic insertion machine using carrier tape)
★ 对于详细规格,请参阅附页(
★ 符合RoHS(
RoHS Compliant)
For detail specifications, please refer to the attached)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+105℃
额定工作电压(Rated Voltage Range)
静电容量范围(Capacitance Range) 0.1-1500 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损 耗 角正 切 ( Dissipation Factor)( tanδ)
+20℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
耐焊接热(Resistance to soldering heat)
Load Life
)
(at 120Hz)
I≤0.01CV or 3(uA) After 2 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 6.3 10 16 25 35 50
最高阻抗比率(
额定电压(VDC)
Rated voltage(VDC)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃ )
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±25%(Capacitance change: within±25% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: Not more than 200% of specified value)
漏电流:小于等于规格值(Leakage current : Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃ )
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20 :Same limits as ℃Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
application of DC working voltage for 30 minutes)
shall be kept on the hot plate maintained at 250Ċfor 30 seconds. After removing form the hot plate and
restored at room temperature, they meet the characteristic requirements listed under.)
漏电流(Leakage current) 小于规定值(Less than specified)
容量变化(value Capacitance change)
损耗角(tan δ) 小于规定值(Less than specified)
纹波电流(A),在105 120HZ ℃(Ripple Current ( A, rms ) at 105℃ 120Hz)
91
91
140 8x10.5
155 10x10.5 190 10x10.5
175
198
35
(44)
42 6.3x5 51
6.3x5.5
6.3x7.7
6.3x7.7
8x10.5
10x10.5 300
50
58
66
84
84
155 10x10.5
50
(63)
6.3x7.7
8x6.5
6.3x7.7
8x6.5
8x10.5 140
33
60
60
66
66
180
220
16/87
Page 17
120HZ
HV
Series
10
C
athode
Voltage
P
HV 系列 105(℃ HV Series 105)℃
特性(Features)
★ 105℃ 2000H寿命(Long life of 2000 hrs at 105℃)
★ 可用回流焊(Reflow soldering is available)
★ 可用于高密度安装(Available for high density mounting)
★ 对于详细规格,请参阅附页(
★ 符合RoHS(
RoHS Compliant)
For detail specifications, please refer to the attached)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+105℃
额定工作电压(Rated Voltage Range)
静电容量范围(Capacitance Range) 0.1-1500 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损 耗 角正 切 ( Dissipation Factor)( tanδ)
+20℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
耐焊接热(Resistance to soldering heat)
Load Life
)
(at 120Hz)
I≤0.01CV or 3(uA) After 2 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 6.3 10 16 25 35 50
最高阻抗比率(
额定电压(VDC)
Rated voltage(VDC)
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃ )
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±25%(Capacitance change: within±25% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: Not more than 200% of specified value)
漏电流:小于等于规格值(Leakage current : Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃ )
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20 :Same limits as Load ℃
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
application of DC working voltage for 30 minutes)
shall be kept on the hot plate maintained at 250Ċfor 30 seconds. After removing form the hot plate a nd
restored at room temperature, they meet the characteristic requirements listed under.)
漏电流(Leakage current) 小于规定值(Less than specified)
容量变化(value Capacitance change)
损耗角(tan δ) 小于规定值(Less than specified)
纹波电流(A),在105 120HZ ℃(Ripple Current ( A, rms ) at 105℃ 120Hz)
25
(32)
48
56
60
110
160
175 8x10.5
180
190
290 10x10.5 360
5X5.5
6.3x5.5
6.3x7.7
8x6.5
6.3x7.7
8x6.5
6.3x7.7
8x10.5
8x10.5
10x10.5
35
(44)
40
46
47
50
60
65
130
180
190 10x10.5
250
280
6.3x7.7
8X6.5
6.3x7.7
8x6.5
6.3x7.7
8x10.5
10x10.5 315
10x10.5 350
50
(63)
28
50
55
95
135
115
155
330
18/87
Page 19
120HZ
JV Series
D
10
C
athode
Voltage
C
JV 系列 105(℃ JV Series 105)℃
特性(Features)
★ 大小尺寸的长寿命贴片电容(Chip type long life capacitance in large case sizes)
★ 105 ℃ 3000H寿命(Chip type with load life of 3000 hours at 105℃)
★ 专为表面安装高密度印刷电路板(Designed for surface mounting on high density PC boa)
★ 适用于使用自动插入机用载带(Applicable to automatic insertion machine using carrier tape)
★ 对于详细规格,请参阅附页(
★ 符合RoHS(
RoHS Compliant)
For detail specifications, please refer to the attached)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+105℃
额定工作电压(Rated Voltage Range)
静电容量范围(Capacitance Range) 0.1-1000 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损 耗 角正 切 ( Dissipation Factor)( tanδ)
+20℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
耐焊接热(Resistance to soldering heat)
Load Life
)
(at 120Hz)
I≤0.01CV or 3(uA) After 2 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 6.3 10 16 25 35 50
最高阻抗比率(
额定电压(VDC)
Rated voltage(VDC)
测试条件(Test conditions)
持续时间:3000Hrs(Duration time :3000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃ )
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±25%(Capacitance change: within±25% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: Not more than 200% of specified value)
漏电流:小于等于规格值(Leakage current : Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃ )
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20 :Same limits as Load ℃
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
application of DC working voltage for 30 minutes)
shall be kept on the hot plate maintained at 250Ċfor 30 seconds. After removing form the hot plate a nd
restored at room temperature, they meet the characteristic requirements listed under.)
漏电流(Leakage current) 小于规定值(Less than specified)
容量变化(value Capacitance change)
损耗角(tan δ) 小于规定值(Less than specified)
纹波电流(A),在105 120HZ ℃(Ripple Current ( A, rms ) at 105℃ 120Hz)
35
(44)
45 6.3x7.7
58 8x10.5 140
93 8x10.5 170
50
(63)
33
58
20/87
Page 21
)
RL
Series
¢
D
RL 系列(Series) Low ESR≤7mΩ
特性(Features)
¼
★ 高频率、超低阻抗。(Very Low ESR at high frequency range.)
★ 允许超大纹波电流。(Very Large permissible ripple current.)
★ 符合RoHS(
RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -55~+105℃
额定工作电压(Rated Voltage Range)
静电容量范围(Capacitance Range) 180~3500 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
ESR(100K-300KHZ)
高温负荷寿命(
高 温 高 湿 储 存 特 性 ( Characteristics of high
temperature and humidity storage)
Load Life
)
纹波电流的频率系数(Frequency Coefficient for Ripple Current)
频率
(Frequency)
系数(Coefficient
尺寸图:(单位:mm)(Diagram of Dimensions:(unit:mm))
L+αmax
性能特点(
I≤0.2CV (uA) After 2 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
不超过指定值
Not to exceed the value specified
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change: within±20% of the initial value)
损耗角:小于等于规格值的150%(Dissipation factor: Not more than150% of specified value)
漏电流:小于等于规格值(Leakage current : Not more than the specified value)
ESR:不超过规格值的150%(ESR:Not to exceed 150% of the value specified)
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温湿度:温度+60℃ ;湿度90-95%(Environmental temperature and humidity: Temperature +60 ℃;
humidity 90-95%)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
项目(
使用温度范围(Operating Temperature Range) -55~+105℃
额定工作电压(Rated Voltage Range)
静电容量范围(Capacitance Range) 39~3500 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
ESR(100K-300KHZ)
高温负荷寿命(
高 温 高 湿 储 存 特 性 ( Characteristics of high
temperature and humidity storage)
Load Life
)
I≤0.2CV (uA) After 2 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 2.5 4 6.3 10 16 20 25
不超过指定值
Not to exceed the value specified
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change: within±20% of the initial value)
损耗角:小于等于规格值的150%(Dissipation factor: Not more than150% of specified value)
漏电流:小于等于规格值(Leakage current : Not more than the specified value)
ESR:不超过规格值的150%(ESR:Not to exceed 150% of the value specified)
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温湿度:温度+60℃ ;湿度90-95%(Environmental temperature and humidity: Temperature +60 ℃;
humidity 90-95%)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
DF(%) 8-10 8-10 7-10 8-10 8-10 8-10
性能特点(
I≤0.02CV (uA) 经过2分钟的额定电压
Performance Characteristics
2.5-25 VDC
纹波电流的频率系数(Frequency Coefficient for Ripple Current)
纹波电流(A),在105℃ 100KHZ (Ripple Current ( A, rms ) at 105℃ 100KHz)
16
(18.4)
15
12
3700
3900
3900
5500
24/87
Page 25
)
RF
Series
D
RF系列超低阻抗 ESR ≤ 6mΩ(RF Series Ultra Low ESR ≤ 6mΩ)
特性(Features)
¼
★ 高频率、超低阻抗。(Ultra Low ESR at high frequency range.)
★ 允许超大纹波电流。(Ultra Large permissible ripple current.)
★ 符合RoHS(
RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -55~+105℃
额定工作电压(Rated Voltage Range)
静电容量范围(Capacitance Range) 180~3500 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
ESR(100K-300KHZ)
高温负荷寿命(
高 温 高 湿 储 存 特 性 ( Characteristics of high
temperature and humidity storage)
Load Life
)
纹波电流的频率系数(Frequency Coefficient for Ripple Current)
频率
(Frequency)
系数(Coefficient
尺寸图:(单位:mm)(Diagram of Dimensions:(unit:mm))
¢
L+αmax
性能特点(
I≤0.2CV (uA) After 2 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
不超过指定值
Not to exceed the value specified
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change: within±20% of the initial value)
损耗角:小于等于规格值的150%(Dissipation factor: Not more than150% of specified value)
漏电流:小于等于规格值(Leakage current : Not more than the specified value)
ESR:不超过规格值的150%(ESR:Not to exceed 150% of the value specified)
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温湿度:温度+60℃ ;湿度90-95%(Environmental temperature and humidity: Temperature +60 ℃;
humidity 90-95%)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
纹波电流(A),在105℃ 100KHZ (Ripple Current ( A, rms ) at 105℃ 100KHz)
8x11.5
10x12.5
8x11.5
10x12.5
8x11.5
10x12.5
8x11.5
10x12.5
6 6100 8x11.5 6 6600
66100
66100
66100
66100
66100
66100
6
6600 10x12.5
66600
67100
67100
67100
6
7100
Size ESR Ripple
8x11.5
8x11.5
8x11.5
8x11.5
8x11.5
8x11.5
10x12.5
10x12.5
10x12.5
10
(11.5)
6
6
6
6
6
6
6
6
6
6
6600
6600
6600
6600
6600
6600
6600
7100
7100
7100
26/87
Page 27
4
SM
Series
(Sleeve
)
(Rubb
er end seal
)
⊕
d¢
D±0.5
KapuCon
SM系列 5、7mm 85℃(SM Series 5、7mm 85℃)
特性(Features)
★ 设计节省空间,高密度的插入。(Design for space-saving and high density insertion.)
★ 4WV产品标准化最近电池电源设备。(4WV products are standardized for recent battery power source devices.)
★ 可代替价格较高的钽电容器。(Low price compared to Tantalum capacitors.)
★ 应用范围:录像机,汽车音响和商业应用。(Applications: VTR, car radio and commercial applications.)
★ 对于详细规格,请参阅附页(For detail specifications, please refer to the attached)
★ 符合RoHS(
RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+85℃
额定工作电压(Rated Voltage Range)
静电容量范围(Capacitance Range) 0.1-470 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
纹波电流的频率系数(Frequency Coefficient for Ripple Current)
容量(uf)\频率(HZ)
CAP(uf)\Frequency(HZ)
CAP≤10
10<CAP≤100
100<CAP≤1000
尺寸图:(单位:mm)(Diagram of Dimensions:(unit:mm))
胶管
L+αmax
性能特点(
I≤0.01CV or 3 (uA) After 1 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
最高阻抗比率(
额定电压
(at 120Hz)
50(60) 120 400 1K 10K 50K-100K
0.8 1.0 1.3 1.45 1.65 1.7
0.8 1.0 1.23 1.36 1.48 1.53
0.8 1.0 1.16 1.25 1.35 1.38
Rated voltage(VDC)
Z-25℃/Z+20℃
Z-40℃/Z+20℃
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+85℃(Ambient temperature:+85℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value (4V:≤±30%))
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+85℃(Ambient temperature:+85℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
纹波电流(A),在85℃ 120HZ (Ripple Current ( A, rms ) at 85℃ 120Hz)
5x7 33 6.3x7 38
30
45
65
29/87
Page 30
GM
Series
d¢
L+αmax 15mi
4mi
D±0.5
KapuCon
GM系列 85℃普通品(GM Series General Purpose 85℃)
特性(Features)
★ 85℃ 2000小时负载寿命。(Load life 2000 hrs at 85℃.)
★ 安全阀结构设计。(Safety vent construction design.)
★ 对于详细规格,请参阅附页(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
85℃
GM
400V
47uF
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+85℃-25~+85℃
额定工作电压(Rated Voltage Range) 6.3~100VDC 160~450VDC
静电容量范围(Capacitance Range) 0.1~33000 uf 0.47~560uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.01CV 或3 (uA) 经过1分钟的额定电压
I≤0.01CV or 3 (uA) After 1 minutes with rated
working voltage applied
下表中的比值以下(%)Less than the value under table (%)
当容量大于1000uF时,每增加1000uF,DF增加2%。(For capacitance ×1000 uF, add 2% per another 1000 uF)
最高阻抗比率(
额定电压Rated
voltage(VDC)
Z-25℃/Z+20℃
Z-40℃/Z+20℃
当容量大于1000uF时,每增加1000uF,增加0.5,在-25℃/+20℃时,
当容量大于1000uF时,每增加1000 uF,增加1,在-40℃/+20℃时。
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温度:+85℃(Ambient temperature:+85℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value (4V:≤±30%))
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+85℃(Ambient temperature:+85℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
纹波电流(A),在85℃ 120HZ (Ripple Current ( A, rms ) at 85℃ 120Hz)
20
33
38
43
48
51
135
165
210
220
240
260
350
(400)
8x12
10x12.5
8x12
10x12.5
10x12.5
10x16
13x20 180
13x25 250
16x25 290
30
32
46
51
63
66
6.3x11
8x12
6.3x11
8x12
8x12
10x12
.5
8x12
10x12
.5
10x12
.5
10x16
10x20
13x20
13x20
13x25
13x25
16x25
16x25
16x32
16x36
18x32
18x32
18x36
400
(450)
12 6.3x11 12
20
22
32
35
10x12.5
45
10x12.5
53
66
70
115
120
190
200
230
250
270
290
410
420
440
450
450
(500)
8x12
8x12
10x16
10x16 56
13x20
13x25
13x25
16x25
16x25 210
16x25
16x32
18x32
18x36
18x41 420
22
32
35
32
40
105
110
150
165
260
280
370
390
32/87
Page 33
4
SK Series
(Sleeve
)
(Rubb
er end seal
)
⊕
d¢
D±0.5
KapuCon
SK系列 5、7mm 105℃(SK Series 5、7mm 105℃)
特性(Features)
★ 105℃ 1000小时负载寿命(Load life 105Ċ, 1000 hrs assured)
★ 对于详细规格,请参阅附页(For detail specifications, please refer to the attached)
★ 符合RoHS(
RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+105℃
额定工作电压(Rated Voltage Range)
静电容量范围(Capacitance Range) 0.1-470 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
纹波电流的频率系数(Frequency Coefficient for Ripple Current)
容量(uf)\频率(HZ)
CAP(uf)\Frequency(HZ)
CAP≤10
10<CAP≤100
100<CAP≤1000
尺寸图:(单位:mm)(Diagram of Dimensions:(unit:mm))
胶管
L+αmax
性能特点(
I≤0.01CV or 3 (uA) After 1 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
最高阻抗比率(
额定电压
(at 120Hz)
50(60) 120 400 1K 10K 50K-100K
0.8 1.0 1.3 1.45 1.65 1.7
0.8 1.0 1.23 1.36 1.48 1.53
0.8 1.0 1.16 1.25 1.35 1.38
Rated voltage(VDC)
Z-25℃/Z+20℃
Z-40℃/Z+20℃
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value (4V:≤±30%))
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
纹波电流(A),在105℃ 120HZ (Ripple Current ( A, rms ) at 105℃ 120Hz)
25
(32)
4x7
5x7
4x7
5x7
5x7
6.3x7
5x7
6.3x7
6.3x7
8x7
8x7 115 8x7
30
33
45
48
52
60
68
72
4x7
5x7
5x7
6.3x7
5x7
6.3x7
6.3x7
8x7
8x7 80
35
(44)
24
28
30
35
38
45
50
58
54
68
50
(63)
5 4x7 6
7 4x7 7
4x7
5x7
5x7
6.3x7
5x7
6.3x7
6.3x7 52 8x7 55
6.3x7
8x7
8x7 78
27
29
32
33
35
38
60
63
5x7
6.3x7
6.3x7 35
6.3x7 40
8x7 65
63
(79)
29
33
35/87
Page 36
KS
Series
d¢
L+αmax 15mi
4mi
D±0.5
KapuCon
S
afety Device
KS系列 105℃标准品(KS Series Standard 105℃)
特性(Features)
★ 105℃ 2000小时负载寿命。(Load life 2000 hrs at 105℃.)
★ 适用于通信设备,开关电源等。(Used in communication equipments, switching power supply, etc.)
★ 安全阀结构设计。(Safety vent construction design.)
★ 对于详细规格,请参阅附页(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
105℃
KS
50V
1000uF
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+105℃-25~+105℃
额定工作电压(Rated Voltage Range) 6.3~100VDC 160~450VDC
静电容量范围(Capacitance Range) 0.1~22000 uf 0.47~470 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.01CV 或3 (uA) 经过1分钟的额定电压
I≤0.01CV or 3 (uA) After 1 minutes with rated
working voltage applied
下表中的比值以下(%)Less than the value under table (%)
当容量大于1000uF时,每增加1000uF,DF增加2%。(For capacitance ×1000 uF, add 2% per another 1000 uF)
最高阻抗比率(
额定电压Rated
voltage(VDC)
Z-25℃/Z+20℃
Z-40℃/Z+20℃
当容量大于1000uF时,每增加1000uF,增加0.5,在-25℃/+20℃时,
当容量大于1000uF时,每增加1000 uF,增加1,在-40℃/+20℃时。
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value (4V:≤±30%))
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温度:+85℃(Ambient temperature:+85℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value (4V:≤±30%))
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+85℃(Ambient temperature:+85℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value (4V:≤±30%))
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+85℃(Ambient temperature:+85℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
(Used in communication equipments, switching power supply, industrial measuring instruments, etc.)
★ 105℃负荷寿命在2000〜 5000小时。(Load life 2000~5000 Hrs at 105℃)
★ 安全阀结构设计。(Safety vent construction design.)
★ 对于详细规格,请参阅附页(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+105℃-25~+105℃
额定工作电压(Rated Voltage Range) 6.3~100VDC 160~450VDC
静电容量范围(Capacitance Range) 0.47~15000 uf 0.47~330 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.01CV 或3 (uA) 经过2分钟的额定电压
I≤0.01CV or 3 (uA) After 2 minutes with rated
working voltage applied
下表中的比值以下(%)Less than the value under table (%)
当容量大于1000uF时,每增加1000uF,DF增加2%。(For capacitance ×1000 uF, add 2% per another 1000
uF)
最高阻抗比率(
额定电压Rated
voltage(VDC)
Z-25℃/Z+20℃
Z-40℃/Z+20℃
当容量大于1000uF时,每增加1000uF,增加0.5,在-25℃/+20℃时,
当容量大于1000uF时,每增加1000 uF,增加1,在-40℃/+20℃时。
测试条件(Test conditions)
持续时间:见右表(Duration time:as right)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value (4V:≤±30%))
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
纹波电流(A),在105℃ 100KHZ (Ripple Current ( A, rms ) at 105℃ 100kHz)
最大阻抗(Ω)在 20℃ 100KHz(Max Impedance (Ω) at 20Ċ 100KHz)
(500)
47/87
450
Page 48
KR
Series
d¢
L+αmax 15mi
4mi
D±0.5
KapuCon
S
afety Device
KR系列 105℃长寿命(KR Series 105℃ Long Life)
特性(Features)
★ 用于电子镇流器,开关电源,工业测量仪器。
(Used in electronic ballast, switching power supply, industrial measuring instruments.)
★ 高纹波电流。(Higher ripple current)
★ 105℃负荷寿命在5000〜 10000小时在(Load life 5000 〜10000Hrs at 105℃)
★ 安全阀结构设计。(Safety vent construction design.)
★ 对于详细规格,请参阅附页。(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+105℃-25~+105℃
额定工作电压(Rated Voltage Range) 10~50VDC 160~450VDC
静电容量范围(Capacitance Range) 6.8~3300 uf 6.8~220 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.01CV 或3 (uA) 经过1分钟的额定电压
I≤0.01CV or 3 (uA) After 1 minutes with rated
working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 10 16 25 35 50 160 200 250 350 400 450
DF(%)max 19 16 14 12 10 15 15 15 20 20 20
当容量大于1000uF时,每增加1000uF,DF增加2%。(For capacitance ×1000 uF, add 2% per another 1000
uF)
最高阻抗比率(
额定电压Rated voltage(VDC)
Z-25℃/Z+20℃
当容量大于1000uF时,每增加1000uF,增加0.5,在-25℃/+20℃时,
当容量大于1000uF时,每增加1000 uF,增加1,在-40℃/+20℃时。
测试条件(Test conditions)
持续时间:见右表(Duration time:as right)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value (4V:≤±30%))
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
application of DC working voltage for 30 minutes)
Impedance ratio max
性能特点(
10 16 25 35 50 160 200 250 350 400 450
4 3 2 2 2 3 3 3 6 6 6
Performance Characteristics
I≤0.04CV (uA) 经过1分钟的额定电压
I≤0.04CV (uA) After 1 minutes with rated
working voltage applied
)
纹波电流的频率系数(Frequency Coefficient for Ripple Current)
纹波电流(A),在105℃ 100KHZ (Ripple Current ( A, rms ) at 105℃ 100kHz)
25
(32)
10x16 580 10x20 760 13x20 977
350
(400)
Size Ripple
35
(44)
400
(450)
Size Ripple
8x12
10x12.5
Size Ripple
50
(63)
287
300
356
450
(500)
430
710
950
49/87
Page 50
10
TH
Series
d¢
L+αmax 15mi
4mi
D±0.5
K
apuCon
S
afety Device
TH系列高温品(TH Series High Temperature)
特性(Features)
★ 该系列已保证在125℃的工作温度范围,使用1000〜 2000小时寿命,-40℃到+125℃
The series has guaranteed operating life of 1000~2000 hours at 125Ċ widest operating temperature range, -40 to +125Ċ
★应用:高可靠性设备,开关电源的滤波电路,工业控制设备。
Applications : High reliability equipment, filtering circuit of switching power supply, and industrial control equipment.
★ 对于详细规格,请参阅附页。(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+125℃-25~+125℃
额定工作电压(Rated Voltage Range) 10~100VDC 160~350VDC
静电容量范围(Capacitance Range) 0.47~1000 uf 1~100 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.01CV 或3 (uA) 经过1分钟的额定电压
I≤0.01CV or 3 (uA) After 1 minutes with rated
working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 10 16 25 35 50 63 100 160 200 250 350
DF(%)max 18 15 13 12 10 8 7 7 8 10 12
当容量大于1000uF时,每增加1000uF,DF增加2%。(For capacitance ×1000 uF, add 2% per another 1000
uF)
最高阻抗比率(
额定电压Rated voltage(VDC)
Z-25℃/Z+20℃
Z-40℃/Z+20℃
当容量大于1000uF时,每增加1000uF,增加0.5,在-25℃/+20℃时,
当容量大于1000uF时,每增加1000 uF,增加1,在-40℃/+20℃时。
测试条件(Test conditions)
持续时间:1000-2000H(Duration time: 1000-2000H)
环境温度:+125℃(Ambient temperature:+125℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±15%(Capacitance change:≤±15% of the initial value)
损耗角:小于等于规格值的150%(Dissipation factor: ≤150% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+125℃(Ambient temperature:+125℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
application of DC working voltage for 30 minutes)
Impedance ratio max
性能特点(
10 16 25 35 50 63 100 160-250 350-450
3 2 2 2 2 2 2 3 6
4 4 4 4 4 4 4 6 -
Performance Characteristics
I≤0.02CV (uA) 经过1分钟的额定电压
I≤0.02CV (uA) After 1 minutes with rated
working voltage applied
)
纹波电流的频率系数(Frequency Coefficient for Ripple Current)
纹波电流(A),在125℃ 120HZ (Ripple Current ( A, rms ) at 125℃ 120Hz)
36 6.3x11
43 8x12 50 10x12.5
60 10x16 68 10x20
35
(44)
250
(300)
Size Ripple
41 8x12 45
53 10x16 60
Size Ripple
50
(63)
164
350
(400)
55
75
110
180
200
245
51/87
Page 52
10
TE
Series
d¢
L+αmax 15mi
4mi
D±0.5
KapuCon
TE系列高温品(TE Series High Temperature)
特性(Features)
★ 该系列已保证在130℃的工作温度范围,使用2000〜3000小时寿命,-40℃到+130℃
The series has guaranteed operating life of 2000~3000 hours at 130℃ widest operating temperature range, -40 to +130℃
★应用:高可靠性设备,开关电源的滤波电路,工业控制设备。
Applications : High reliability equipment, filtering circuit of switching power supply, and industrial control equipment.
★ 对于详细规格,请参阅附页。(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+130℃
额定工作电压(Rated Voltage Range) 10~50 VDC
静电容量范围(Capacitance Range) 10~4700 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.01CV 或3 (uA) 经过1分钟的额定电压
I≤0.01CV or 3 (uA) After 1 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 10 16 25 35 50
DF(%)max 18 15 13 12 10
当容量大于1000uF时,每增加1000uF,DF增加2%。(For capacitance ×1000 uF, add 2% per another 1000
uF)
最高阻抗比率(
额定电压Rated voltage(VDC)
Z-25℃/Z+20℃
Z-40℃/Z+20℃
当容量大于1000uF时,每增加1000uF,增加0.5,在-25℃/+20℃时,
当容量大于1000uF时,每增加1000 uF,增加1,在-40℃/+20℃时。
测试条件(Test conditions)
持续时间:2000-3000H(Duration time: 2000-3000H)
环境温度:+130℃(Ambient temperature:+130℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±15%(Capacitance change:≤±15% of the initial value)
损耗角:小于等于规格值的150%(Dissipation factor: ≤150% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+130℃(Ambient temperature:+130℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
application of DC working voltage for 30 minutes)
Impedance ratio max
性能特点(
10 16 25 35 50
3 2 2 2 2
4 4 4 4 4
纹波电流的频率系数(Frequency Coefficient for Ripple Current)
纹波电流(A),在130℃ 120HZ (Ripple Current ( A, rms ) at 130℃ 120Hz)
35
(44)
50
(63)
300
53/87
Page 54
KE
Series
d¢
L+αmax 15mi
4mi
D±0.5
KapuCon
≥8
3000
KE系列低阻抗(KE Series Low Impedance)
特性(Features)
★ 高频低阻抗。(Low impedance for high frequency, Anti-Solvent Design.)
★ 105℃ 2000〜 3000小时寿命。(Long Life 2000 ~ 3000 hrs at 105Ċ depending on case size.)
★ 适用于开关电源。(Radial type for switching power supply.)
★ 对于详细规格,请参阅附页(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -55~+105℃
额定工作电压(Rated Voltage Range) 6.3~63VDC
静电容量范围(Capacitance Range) 0.47~15000 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.01CV 或3 (uA) 经过2分钟的额定电压
I≤0.01CV or 3 (uA) After 2 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 6.3 10 16 25 35 50 63
DF(%)max 20 18 16 14 12 10 9
当容量大于1000uF时,每增加1000uF,DF增加2%。(For capacitance ×1000 uF, add 2% per another 1000
uF)
最高阻抗比率(
额定电压Rated voltage(VDC)
Z-25℃/Z+20℃
Z-40℃/Z+20℃
当容量大于1000uF时,每增加1000uF,增加0.5,在-25℃/+20℃时,
当容量大于1000uF时,每增加1000 uF,增加1,在-40℃/+20℃时。
测试条件(Test conditions)
持续时间:见右表(Duration time:as right)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
★ 高频低阻抗。(Low impedance for high frequency, Anti-Solvent Design.)
★ 105℃ 3000~5000小时寿命。(Long Life3000 ~ 5000 hrs at 105Ċ depending on case size.)
★ 适用于开关电源。(Radial type for switching power supply.)
★ 对于详细规格,请参阅附页(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -55~+105℃
额定工作电压(Rated Voltage Range) 6.3~63VDC
静电容量范围(Capacitance Range) 1~10000 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.01CV 或3 (uA) 经过2分钟的额定电压
I≤0.01CV or 3 (uA) After 2 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 6.3 10 16 25 35 50 63
DF(%)max 22 19 16 14 12 10 8
当容量大于1000uF时,每增加1000uF,DF增加2%。(For capacitance ×1000 uF, add 2% per another 1000
uF)
最高阻抗比率(
额定电压Rated voltage(VDC)
Z-25℃/Z+20℃
Z-40℃/Z+20℃
当容量大于1000uF时,每增加1000uF,增加0.5,在-25℃/+20℃时,
当容量大于1000uF时,每增加1000 uF,增加1,在-40℃/+20℃时。
测试条件(Test conditions)
持续时间:见右表(Duration time:as right)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
★ 用于主机板,电脑周边设备等。(Used in mother board, computer peripheral, etc.)
★ 负载寿命在5000〜 8000小时105℃。(Load life 5000 ~8000 Hrs at 105℃)
★ 安全阀结构设计。(Safety vent construction design.)
★ 对于详细规格,请参阅附页(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -55~+105℃
额定工作电压(Rated Voltage Range) 6.3~50VDC
静电容量范围(Capacitance Range) 22~6800 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.01CV 或3 (uA) 经过2分钟的额定电压
I≤0.01CV or 3 (uA) After 2 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 6.3 10 16 25 35 50 63 100
DF(%)max 16 14 12 10 9 8 8 8
当容量大于1000uF时,每增加1000uF,DF增加2%。(For capacitance ×1000 uF, add 2% per another 1000
uF)
最高阻抗比率(
额定电压Rated voltage(VDC)
Z-25℃/Z+20℃
Z-40℃/Z+20℃
当容量大于1000uF时,每增加1000uF,增加0.5,在-25℃/+20℃时,
当容量大于1000uF时,每增加1000 uF,增加1,在-40℃/+20℃时。
测试条件(Test conditions)
持续时间:见右表(Duration time:as right)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
★ 低阻抗。(Low impedance)
★ 高温,长寿命7000~10000小时,105℃。(High temperature, Long life 7000 to 10,000 hours at 105℃)
★ 对于详细规格,请参阅附页(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -55~+105℃
额定工作电压(Rated Voltage Range) 6.3~50VDC
静电容量范围(Capacitance Range) 47~6800 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.01CV 或3 (uA) 经过2分钟的额定电压
I≤0.01CV or 3 (uA) After 2 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 6.3 10 16 25 35 50
DF(%)max 22 19 16 14 12 10
当容量大于1000uF时,每增加1000uF,DF增加2%。(For capacitance ×1000 uF, add 2% per another 1000
uF)
最高阻抗比率(
额定电压Rated voltage(VDC)
Z-25℃/Z+20℃
Z-40℃/Z+20℃
Z-55℃/Z+20℃
当容量大于1000uF时,每增加1000uF,增加0.5,在-25℃/+20℃时,
当容量大于1000uF时,每增加1000 uF,增加1,在-40℃/+20℃时。
当容量大于1000uF时,每增加1000 uF,增加1.5,在-40℃/+20℃时。
测试条件(Test conditions)
持续时间:见右表(Duration time:as right)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±25%(Capacitance change:≤±25% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
纹波电流(A),在105℃ 100KHZ (Ripple Current ( A, rms ) at 105℃ 100kHz)
35
(44)
Size Ripple Impedance
595
600
660
670
1165 0.1 13x25 1550 0.078
最大阻抗(Ω)在20℃ 100KHz(Max Impedance (Ω) at 20℃ 100KHz)
0.35 10x16 650 0.18
0.32 10x16 760 0.16
50
(63)
64/87
Page 65
KY
Series
d¢
L+αmax 15mi
4mi
D±0.5
KapuCon
KY系列超低阻抗(KY Series Ultra Low Impedance)
特性(Features)
★ 超低阻抗为100KHz。(Ultra low impedance in 100KHz.)
★ 由于超低阻抗,可允许更高的纹波电流。(Allow higher ripple current applied due to ultra low impedance.)
★ 在105℃负载寿命2000hrs(Load life 2000hrs at 105Ċ)
★ 适合于主板,电脑周边设备等应用。(Suitable for application of mother board, computer peripheral etc.)
★ 对于详细规格,请参阅附页(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+105℃
额定工作电压(Rated Voltage Range) 6.3~25VDC
静电容量范围(Capacitance Range) 220~3300 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.01CV 或3 (uA) 经过2分钟的额定电压
I≤0.01CV or 3 (uA) After 2 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 6.3 10 16 25
DF(%)max 14 12 10 9
当容量大于1000uF时,每增加1000uF,DF增加2%。(For capacitance ×1000 uF, add 2% per another 1000
uF)
测试条件(Test conditions)
持续时间:2000H(Duration time:2000Ht)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±25%(Capacitance change:≤±25% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
application of DC working voltage for 30 minutes)
Impedance ratio max
性能特点(
6.3 10 16 25
4 3 2 2
6 4 3 3
纹波电流的频率系数(Frequency Coefficient for Ripple Current)
纹波电流(A),在105℃ 100KHZ (Ripple Current ( A, rms ) at 105℃ 100kHz)
Size Ripple
8x12
10x12.5
8x16
10x12.5
8x20
10x16
10x20 2540 0.015
最大阻抗(Ω)在20℃ 100KHz(Max Impedance (Ω) at 20Ċ 100KHz)
1080
1500
1450
1500
1850
1910
Impedance
0.038
0.027
0.029
0.027
0.02
0.018
Size Ripple
8x12 1080
8x12 1150 0.031
8x12
10x12.5
8x20
10x12.5
10x16
8x20
10x16
10x20
10x20 2180 0.016
25
(32)
1450
1850
1440
1720
1830
1820
1920
2060
Impedance
0.032
0.029
0.027
0.025
0.022
0.02
0.018
0.018
0.02
66/87
Page 67
LL
Series
d¢
L+αmax
15mi
4mi
D±0.5
Dumicon
S
afety Device
KapuCon
LL 系列低漏电流(LL Series Low Leakage Current)
特性(Features)
★ 极低的泄漏电流和稳定的特点。(Extremely low and stable leakage current characteristics.)
★ 电容公差±20%(±10%要求)(Close capacitance tolerance ±20% (±10% on requested))
★ 对于详细规格,请参阅附页。(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+105℃
额定工作电压(Rated Voltage Range) 4~63 VDC
静电容量范围(Capacitance Range) 0.1~2200 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.002CV 或0.4 (uA) 经过3分钟的额定电压
I≤0.002CV or 0.4 (uA) After 3 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 4 6.3 10 16 25 35 50 63
DF(%)max 25 22 20 16 14 12 10 10
最高阻抗比率(
额定电压Rated voltage(VDC)
Z-25℃/Z+20℃
Z-40℃/Z+20℃
测试条件(Test conditions)
持续时间:1000-2000H(L:7mm 1000H)(Duration time: 1000-2000H)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
application of DC working voltage for 30 minutes)
Impedance ratio max
性能特点(
4 6.3 10 16 25 35 50 63
6 4 3 3 2 2 2 2
12 10 6 6 4 4 4 3
纹波电流的频率系数(Frequency Coefficient for Ripple Current)
纹波电流(A),在105℃ 120HZ (Ripple Current ( A, rms ) at 105℃ 120Hz)
63
(79)
3
5
6
7
63
12
17
24
32
39
68/87
Page 69
RL
Series
d¢
L+αmax 15mi
4mi
D±0.5
KapuCon
S
afety Device
RL系列节能灯电容(RL Series Energy Saving Lamp capacitor)
特性(Features)
★ 高纹波电流。(High ripple current.)
★ 105℃ 5000H负荷寿命。(Load life of 5000H at 105℃)
★ 对于详细规格,请参阅附页。(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+105℃
额定工作电压(Rated Voltage Range) 160~450 VDC
静电容量范围(Capacitance Range) 1~220 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.03CV+3 uA 或40(uA) 经过2分钟的额定电压
I≤0.03CV +3 uA or 40 (uA) After 2 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 160 200 250 350 400 450
DF(%)max 15 15 20 20 20 20
最高阻抗比率(
额定电压Rated voltage(VDC)
Z-25℃/Z+20℃
测试条件(Test conditions)
持续时间:5000H (Duration time: 5000H)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
application of DC working voltage for 30 minutes)
Impedance ratio max
性能特点(
160 200 250 350 400 450
3 3 3 6 6 6
纹波电流的频率系数(Frequency Coefficient for Ripple Current)
纹波电流(A),在105℃ 100KHZ (Ripple Current ( A, rms ) at 105℃ 100KHz)
450
(500)
70/87
Page 71
RZ
Series
d¢
L+αmax 15mi
4mi
D±0.5
KapuCon
S
afety Device
RZ系列节能灯电容(RZ Series Energy Saving Lamp capacitor)
特性(Features)
★ 节能灯使用,高纹波电流。( For Electronic Ballast ,High ripple current.)
★ 105℃ 8000-10000H负荷寿命。(Load life of 8000-10000H at 105℃)
★ 对于详细规格,请参阅附页。(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+105℃
额定工作电压(Rated Voltage Range) 160~450 VDC
静电容量范围(Capacitance Range) 1~220 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
低温特性(在120HZ)
Low Temperature Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
(at 120Hz)
I≤0.03CV+3 uA 或40(uA) 经过2分钟的额定电压
I≤0.03CV+3 uA or 40 (uA) After 2 minutes with rated working voltage applied
下表中的比值以下(%)Less than the value under table (%)
WV 160 200 250 350 400 450
DF(%)max 15 15 20 20 20 20
最高阻抗比率(
额定电压Rated voltage(VDC)
Z-25℃/Z+20℃
测试条件(Test conditions)
持续时间:8000-10000H (Duration time: 8000-10000H)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
application of DC working voltage for 30 minutes)
Impedance ratio max
性能特点(
160 200 250 350 400 450
3 3 3 6 6 6
纹波电流的频率系数(Frequency Coefficient for Ripple Current)
纹波电流(A),在105℃ 100KHZ (Ripple Current ( A, rms ) at 105℃ 100KHz)
450
(500)
72/87
Page 73
RF
Series
Rubber end seal
d¢
L+αmax 15mi
4mi
D±0.5
KapuCon
RF系列闪光灯电容(RF Series Photo Flash Capacitor)
特性(Features)
★ RF系列,低功耗和低漏电流的因素为相机闪光灯适用,不仅拥有卓越的容积效率。
RF Series is for photo flash applications that require not only superior volumetric efficiency,
low dissipation factor and low leakage current.
★ 这些电容有效地转化成光的静电能量。(These capacitors effectively convert electrostatic energy into light.)
★ 对于详细规格,请参阅附页。(For detail specifications, please refer to the attached)
★ 符合RoHS(RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -20~+55℃
额定工作电压(Rated Voltage Range)
静电容量范围(Capacitance Range) 100~450 uf
电容公差(Capacitance Tolerance) -10%~±20%(120HZ +25℃)
漏电流(Leakage Current )最高温度+20℃
损耗角正切(Dissipation Factor)(tanδ)120HZ +20
℃
高温负荷寿命(
高温储存特性(Shelf Life)
Load Life
)
测试条件(Test conditions)
持续时间:5000次 (Duration time: 5000Times)
环境温度:室温(5-35℃)(Ambient temperature: Room Temperature (5-35℃))
施加电压:充电和放电周期:30秒(Applied voltage :Charge and Discharge Cycles : 30 Sec)
在环境温度为+25℃时测试(After test requirement at +25℃)
电容量变化:小于等于初始值的±10%(Capacitance change:≤±10% of the initial value)
损耗角:小于等于规格值的150%(Dissipation factor: ≤100% of the specified value)
漏电流:小于等于规格值的150%(Leakage current : ≤150% of the initial specified value )
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+55℃(Ambient temperature:+55℃)
施加电压:无(Applied voltage:None)
在环境温度为+25℃时测试:等现于高温负载寿命(After test requirement at +25℃:Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
application of DC working voltage for 30 minutes)
尺寸图:(单位:mm)(Diagram of Dimensions:(unit:mm))
胶管
(
¢D 8 10 12 13 16 18 20
F±0.5 3.5 5 5 5 7.5 7.5 7.5
0.6 0.6 0.8 0.8 0.8 0.8 0.8
d¢
α
1.5
I≤1* C (uA) After 5 minutes with rated working voltage applied
胶盖
)
73/87
性能特点(
I≤1*C (uA) 经过5分钟的额定电压
F±0.5
Performance Characteristics
330/350 VDC
8% MAX
55℃
RF
350V
100uF
)
Page 74
120HZ
KapuCon
LM Series
¢
D
LM 系列牛角端子型 85(℃ LM Series Snap-in Type 85)℃
特性(Features)
直接安装在无卤印刷电路板上。(
★
★ 铝壳设计的防爆通风。(Aluminum case designed explosion-proof ven)
★ 对于详细规格,请参阅附页(
★ 符合RoHS(
RoHS Compliant)
Directly mountable on printed circuit board, without holdors)
For detail specifications, please refer to the attached)
560uf-400V
LM VENT 85℃
KapuCon
560uf-400V
LM VENT 85℃
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+85℃-25~+85℃
额定工作电压(Rated Voltage Range)
静电容量范围(Capacitance Range) 470-68000 uf 47-3300uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃
损耗角 正切( Dissipation Factor)(tanδ)
+20℃
低 温 特 性 ( 在 120HZ )
Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
(at 120Hz)
Load Life
Low Temperature
)
10-100WV 160-450WV
(I≤0.02CV After 5 minutes with rated working voltage applied)
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温度:+85℃(Ambient temperature:+85℃ )
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+85℃(Ambient temperature:+85℃ )
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20 :Same limits as Load ℃
life)
测量前请 先用 工作直流电 压充电30分钟。(Pre-treatment for measurements shall be conducted after
application of DC working voltage for 30 minutes)
WV
Impedance ratio max
性能特点(
I≤0.02CV 经过5分钟的额定电压
10~16 25~3550~6380~100160~250315~450
Performance Characteristics
)
)
容量与频率测试(Multiplier for Ripple Current vs. Frequency)
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value)
损耗角:小于等于规格值的200%(Dissipation factor: ≤200% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃)
施加电压:无(Applied voltage:None)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20℃:Same limits as Load
life)
测量前请 先用 工作直流电 压充电30分钟。(Pre-treatment for measurements shall be conducted after
项目(
使用温度范围(Operating Temperature Range) -40~+85℃-25~+85℃
额定工作电压(Rated Voltage Range)
静电容量范围(Capacitance Range) 3300-1000000 uf 220-68000 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃I≤0.02CV 经过5分钟的额定电压(I≤0.02CV After 5 minutes with rated working voltage applied)
损 耗 角正 切 ( Dissipation Factor)( tanδ)
+20℃
低 温 特 性 ( 在 120HZ )
Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
(at 120Hz)
Load Life
)
容量与频率测试(Multiplier for Ripple Current vs. Frequency)
容量(uf)\频率(HZ)
CAP(uf)\Frequency(HZ)
10-50WV 0.8 1 1.03 1.05 1.08
63-100WV 0.8 1 1.05 1.07 1.1
160-450WV 0.8 1 1.1 1.13 1.18
For detail specifications, please refer to the attached)
性能特点(
16-100WV 160-465WV
下表中的比值以下(%)Less than the value under table (%)
¢D
Low Temperature
50(60) 120 400 1K 10K≤
最高阻抗比率(
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温度:+85℃(Ambient temperature:+85℃ )
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value)
损耗角:小于等于规格值的±175%(Dissipation factor: ≤±175% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+85℃(Ambient temperature:+85℃ )
施加电压:无(Applied voltage:None)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value)
损耗角:小于等于规格值的±175%(Dissipation factor: ≤±175% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20 :℃ Same limits as Load
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after
RH 系列螺丝端子型 105(RH Series Screw Terminal Type 105)℃℃
特性(Features)
★ 负荷寿命 105 2000℃小时(Load life: 105 2000 hours℃)
★ 高纹波(
★ 对于详细规格,请参阅附页(
★ 符合RoHS(
High ripple capability.)
RoHS Compliant)
规格(Specifications)
Item)
项目(
使用温度范围(Operating Temperature Range) -40~+105℃-25~+105℃
额定工作电压(Rated Voltage Range)
静电容量范围(Capacitance Range) 1500-1000000 uf 220-100000 uf
电容公差(Capacitance Tolerance) ±20%(120HZ +20℃)
漏电流(Leakage Current )最高温度+20℃I≤0.02CV 经过5分钟的额定电压(I≤0.02CV After 5 minutes with rated working voltage applied)
损 耗 角正 切 ( Dissipation Factor)( tanδ)
+20℃
低 温 特 性 ( 在 120HZ )
Characteristics
高温负荷寿命(
高温储存特性(Shelf Life)
(at 120Hz)
Load Life
)
容量与频率测试(Multiplier for Ripple Current vs. Frequency)
容量(uf)\频率(HZ)
CAP(uf)\Frequency(HZ)
10-50WV 0.8 1 1.03 1.05 1.08
63-100WV 0.8 1 1.05 1.07 1.1
160-450WV 0.8 1 1.1 1.13 1.18
For detail specifications, please refer to the attached)
性能特点(
16-100WV 160-400WV
下表中的比值以下(%)Less than the value under table (%)
¢D
Low Temperature
50(60) 120 400 1K 10K≤
最高阻抗比率(
测试条件(Test conditions)
持续时间:2000Hrs(Duration time :2000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃ )
施加电压:额定直流工作电压(Applied voltage :Rated DC working voltage)
在环境温度为+20℃时测试(After test requirement at +20℃)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value)
损耗角:小于等于规格值的±175%(Dissipation factor: ≤±175% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
测试条件(Test conditions)
持续时间:1000Hrs(Duration time :1000 Hrs)
环境温度:+105℃(Ambient temperature:+105℃ )
施加电压:无(Applied voltage:None)
电容量变化:小于等于初始值的±20%(Capacitance change:≤±20% of the initial value)
损耗角:小于等于规格值的±175%(Dissipation factor: ≤±175% of the specified value)
漏电流:小于等于规格值(Leakage current : ≤Not more than the specified value)
在环境温度为+20℃时测试:等现于高温负载寿命(After test requirement at +20 :Same limits as Load ℃
life)
测量前请先用工作直流电压充电30分钟。(Pre-treatment for measurements shall be conducted after