Datasheet IS62LV2568ALL-85T, IS62LV2568ALL-85HI, IS62LV2568ALL-85H, IS62LV2568ALL-85BI, IS62LV2568ALL-70T Datasheet (ISSI)
...
Integrated Silicon Solution, Inc. — 1-800-379-4774
1
Rev. B
08/01/01
ISSI reserves the right to make changes to its products at any time without notice in order to improve design and supply the best possible product. We assume no responsibility for any
errors which may appear in this publication. © Copyright 2001, Integrated Silicon Solution, Inc.
IS62LV2568ALL
ISSI
®
DESCRIPTION
The
ISSI
IS62LV2568ALL is a low voltage, 262,144 words
by 8 bits, CMOS SRAM. It is fabricated using
ISSI'’
s low
voltage, six transistor (6T),
CMOS technology.
The device
is
targeted
to satisfy the demands of the state-of-the-art
technologies such as cell phones and pagers.
When CE is HIGH (deselected), the device assumes a
standby mode at which the power dissipation
can be reduced
down with CMOS input levels. Additionally, easy memory
expansion is provided by using Chip Enable and Output
Enable inputs, CE and OE. The active LOW Write Enable (WE)
controls both writing and reading of the memory.
The IS62LV2568ALL is available in 32-pin TSOP (Type I),
STSOP (Type I), and 36-pin mini BGA.
FUNCTIONAL BLOCK DIAGRAM
256K x 8 LOW POWER and LOW Vcc
CMOS STATIC RAM
FEATURES
• Access times of 70 and 85 ns
• CMOS low power operation:
— 120 mW (typical) operating
— 6 µW (typical) standby
• Low data retention voltage: 2V (min.)
• Output Enable (OE) and two Chip Enable
(CE1 and CE2) inputs for ease in applications
• TTL compatible inputs and outputs
• Fully static operation:
— No clock or refresh required
• Single 2.5V
(min.)
to 3.3V
(max.)
power supply
• Available in 32-pin TSOP (Type I), STSOP (Type I),
and 36-pin mini BGA
AUGUST 2001
A0-A17
CE1
OE
WE
256K x 8
MEMORY ARRAY
DECODER
COLUMN I/O
CONTROL
CIRCUIT
GND
VCC
I/O
DATA
CIRCUIT
I/O0-I/O7
CE2
IS62LV2568ALL
ISSI
®
2
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. B
08/01/01
PIN DESCRIPTIONS
A0-A17 Address Inputs
CE1 Chip Enable 1 Input
CE2 Chip Enable 2 Input
OE Output Enable Input
WE Write Enable Input
I/O0-I/O7 Input/Output
NC No Connection
Vcc Power
GND Ground
PIN CONFIGURATION
36-pin mini BGA (B)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
A11
A9
A8
A13
WE
CE2
A15
VCC
A17
A16
A14
A12
A7
A6
A5
A4
OE
A10
CE1
I/O7
I/O6
I/O5
I/O4
I/O3
GND
I/O2
I/O1
I/O0
A0
A1
A2
A3
1 2 3 4 5 6
A
B
C
D
E
F
G
H
A0
I/O4
I/O5
GND
Vcc
I/O6
I/O7
A9
A1
A2
OE
A10
CE2
WE
NC
NC
CE1
A11
A3
A4
A5
A17
A16
A12
A6
A7
A15
A13
A8
I/O0
I/O1
Vcc
GND
I/O2
I/O3
A14
32-Pin TSOP (Type I), STSOP (Type I)
IS62LV2568ALL
ISSI
®
Integrated Silicon Solution, Inc. — 1-800-379-4774
3
Rev. B
08/01/01
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol Parameter Value Unit
VTERM Terminal Voltage with Respect to GND –0.5 to Vcc + 0.5 V
VCC Vcc related to GND –0.3 to +3.6 V
TBIAS Temperature Under Bias –40 to +85 °C
TSTG Storage Temperature –65 to +150 °C
PT Power Dissipation 0.7 W
Note:
1. Stress greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation of the
device at these or any other conditions above those indicated in the operational sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect reliability.
CAPACITANCE
(1,2)
Symbol Parameter Conditions Max. Unit
CIN Input Capacitance VIN = 0V 6 pF
COUT Output Capacitance VOUT = 0V 8 pF
Notes:
1. Tested initially and after any design or process changes that may affect these parameters.
2. Test conditions: T
A = 25°C, f = 1 MHz, Vcc = 3.0V.
TRUTH TABLE
Mode W E CE1 CE2 OE I/O Operation Vcc Current
Not Selected X H X X High-Z ISB1, ISB2
(Power-down) X X L X High-Z ISB1, ISB2
Output Disabled H L H H High-Z ICC
Read H L H L DOUT ICC
Write L L H X DIN ICC
OPERATING RANGE
Range Ambient Temperature VCC MIN.VCC MAX.
Commercial 0°C to +70°C 2.5V 3.3V
Industrial –40°C to +85°C 2.5V 3.3V
IS62LV2568ALL
ISSI
®
4
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. B
08/01/01
POWER SUPPLY CHARACTERISTICS
(1)
(Over Operating Range)
-70 -85
Symbol Parameter Test Conditions Min. Max. Min. Max. Unit
ICC Vcc Dynamic VCC = Max., CE = VIL Com. — 30 — 25 mA
Operating IOUT = 0 mA, f = fMAX Ind. — 35 — 30
Supply Current
ISB1 TTL Standby VCC = Max., Com. — 0.4 — 0.4 mA
Current VIN = VIH or VIL,Ind.— 1.0 — 1.0
(TTL Inputs) CE1 ≥ VIH or CE2 ≤ VIL, f = 0
ISB2 CMOS Standby VCC = Max., f = 0 Com. — 5 — 5µA
Current CE1 ≥ VCC – 0.2V, Ind. — 5 — 5
(CMOS Inputs) CE2 ≤ 0.2V,
or VIN ≥ VCC – 0.2V, VIN ≤ 0.2V
Note:
1. At f = fMAX, address and data inputs are cycling at the maximum frequency, f = 0 means no input lines change.
DC ELECTRICAL CHARACTERISTICS (Over Operating Range)
Symbol Parameter Test Conditions Min. Max. Unit
VOH Output HIGH Voltage VCC = Min., IOH = –1.0 mA 2.0 — V
VOL Output LOW Voltage VCC = Min., IOL = 2.1 mA — 0.4 V
VIH Input HIGH Voltage 2.2 VCC + 0.3 V
VIL Input LOW Voltage
(1)
–0.3 0.4 V
ILI Input Leakage GND ≤ VIN ≤ VCC –11µA
ILO Output Leakage GND ≤ VOUT ≤ VCC –11µA
Note:
1. V
IL = –3.0V for pulse width less than 10 ns.
IS62LV2568ALL
ISSI
®
Integrated Silicon Solution, Inc. — 1-800-379-4774
5
Rev. B
08/01/01
READ CYCLE SWITCHING CHARACTERISTICS
(1)
(Over Operating Range)
-70 -85
Symbol Parameter Min. Max. Min. Max. Unit
tRC Read Cycle Time 70 — 85 — ns
tAA Address Access Time — 70 — 85 ns
tOHA Output Hold Time 10 — 15 — ns
tACE1 CE1 Access Time — 70 — 85 ns
tACE2 CE2 Access Time — 70 — 85 ns
tDOE OE Access Time — 35 — 45 ns
tHZOE
(2)
OE to High-Z Output — 25 — 25 ns
tLZOE
(2)
OE to Low-Z Output 5 — 5 — ns
tLZCE1
(2)
CE1 to Low-Z Output 10 — 10 — ns
tLZCE2
(2)
CE2 to Low-Z Output 10 — 10 — ns
tHZCE
(2)
CE1 or CE2 to High-Z Output 0 25 0 25 ns
Notes:
1. Test conditions assume signal transition times of 5 ns or less, timing reference levels of 1.3V, input pulse levels of 0.4V to 2.2V and
output loading specified in Figure 1.
2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested.
AC TEST CONDITIONS
Parameter Unit
Input Pulse Level 0.4V to 2.2V
Input Rise and Fall Times 5 ns
Input and Output Timing 1.3V
and Reference Level
Output Load See Figures 1 and 2
AC TEST LOADS
3070 Ω
5 pF
Including
jig and
scope
3150 Ω
OUTPUT
2.8V
3070 Ω
30 pF
Including
jig and
scope
3150 Ω
OUTPUT
2.8V
Figure 1 Figure 2
IS62LV2568ALL
ISSI
®
6
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. B
08/01/01
DATA VALID
t
AA
t
OHA
t
OHA
t
RC
DOUT
ADDRESS
tRC
tOHA
tAA
tDOE
tLZOE
tACE1/tACE2
tLZCE1/
tLZCE2
tHZOE
HIGH-Z
DATA VALID
tHZCE
ADDRESS
OE
CE1
CE2
DOUT
Notes:
1. WE is HIGH for a Read Cycle.
2. The device is continuously selected. OE, CE1 = V
IL, CE2 = VIH.
3. Address is valid prior to or coincident with CE1 LOW and CE2 HIGH transitions.
READ CYCLE NO. 2
(1,3)
AC WAVEFORMS
READ CYCLE NO. 1
(1,2)
IS62LV2568ALL
ISSI
®
Integrated Silicon Solution, Inc. — 1-800-379-4774
7
Rev. B
08/01/01
WRITE CYCLE SWITCHING CHARACTERISTICS
(1,3)
(Over Operating Range, Standard and Low Power)
-70 -85
Symbol Parameter Min. Max. Min. Max. Unit
tWC Write Cycle Time 70 — 85 — ns
tSCE1 CE1 to Write End 65 — 70 — ns
tSCE2 CE2 to Write End 65 — 70 — ns
tAW Address Setup Time to Write End 65 — 70 — ns
tHA Address Hold from Write End 0 — 0 — ns
tSA Address Setup Time 0 — 0 — ns
tPWE
(4)
WE Pulse Width 60 — 60 — ns
tSD Data Setup to Write End 30 — 35 — ns
tHD Data Hold from Write End 0 — 0 — ns
tHZWE
(2)
WE LOW to High-Z Output — 33 — 25 ns
tLZWE
(2)
WE HIGH to Low-Z Output 5 — 5 — ns
Notes:
1.
Test conditions assume signal transition times of 5 ns or less, timing reference levels of 1.3V, input pulse levels of 0.4V to 2.2V and output loading specified in Figure 1.
2. Tested with the load in Figure 2. Transition is measured ±500 mV from steady-state voltage. Not 100% tested.
3.
The internal write time is defined by the overlap of CE1 LOW, CE2 HIGH and WE LOW. All signals must be in valid states to initiate a Write, but any one can go inactive to
terminate the Write. The Data Input Setup and Hold timing are referenced to the rising or falling edge of the signal that terminates the Write.
4. Tested with OE HIGH.
DATA-IN VALID
DATA UNDEFINED
t
WC
t
SCE1
t
SCE2
t
AW
t
HA
t
PWE
(4)
t
HZWE
HIGH-Z
t
LZWE
t
SA
t
SD
t
HD
ADDRESS
CE1
CE2
WE
DOUT
DIN
AC WAVEFORMS
WRITE CYCLE NO. 1 (CE Controlled, OE = HIGH or LOW)
IS62LV2568ALL
ISSI
®
8
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. B
08/01/01
WRITE CYCLE NO. 2 (WE Controlled: OE is HIGH During Write Cycle)
DATA-IN VALID
DATA UNDEFINED
tWC
tSCE1
tSCE2
tAW
tHA
tPWE1, 2
tHZWE
HIGH-Z
tLZWE
tSA
tSD tHD
ADDRESS
OE
CE1
CE2
WE
DOUT
DIN
DATA-IN VALID
DATA UNDEFINED
t
WC
t
SCE1
t
SCE2
t
AW
t
HA
t
PWE1, 2
t
HZWE
HIGH-Z
t
LZWE
t
SA
t
SD
t
HD
ADDRESS
OE
CE1
CE2
WE
DOUT
DIN
WRITE CYCLE NO. 3 (WE Controlled: OE is LOW During Write Cycle)
IS62LV2568ALL
ISSI
®
Integrated Silicon Solution, Inc. — 1-800-379-4774
9
Rev. B
08/01/01
DATA RETENTION SWITCHING CHARACTERISTICS
Symbol Parameter Test Condition Min. Max. Unit
VDR Vcc for Data Retention See Data Retention Waveform 2.0 3.3 V
I
DR Data Retention Current Vcc = 2.0V, CE1 ≥ Vcc – 0.2V Com. — 2µA
Ind. — 5µA
tSDR Data Retention Setup Time See Data Retention Waveform 0 — ns
tRDR Recovery Time See Data Retention Waveform tRC — ns
DATA RETENTION WAVEFORM (CE1 Controlled)
V
CC
CE1 ≥ V
CC
- 0.2V
t
SDR
t
RDR
V
DR
CE1
GND
3.0V
2.2V
Data Retention Mode
DATA RETENTION WAVEFORM (CE2 Controlled)
V
CC
CE2 ≤ 0.2V
t
SDR
t
RDR
V
DR
0.4V
CE2
GND
3.0
2.2V
Data Retention Mode
IS62LV2568ALL
ISSI
®
10
Integrated Silicon Solution, Inc. — 1-800-379-4774
Rev. B
08/01/01
ORDERING INFORMATION
Commercial Range: 0°C to +70°C
Speed (ns) Order Part No. Package
70 IS62LV2568ALL-70B mini BGA (6mm x 8mm)
IS62LV2568ALL-70T TSOP, Type I
IS62LV2568ALL-70H STSOP, Type I
85 IS62LV2568ALL-85B mini BGA (6mm x 8mm)
IS62LV2568ALL-85T TSOP, Type I
IS62LV2568ALL-85H STSOP, Type I
Industrial Range: –40°C to +85°C
Speed (ns) Order Part No. Package
70 IS62LV2568ALL-70BI mini BGA (6mm x 8mm)
IS62LV2568ALL-70TI TSOP, Type I
IS62LV2568ALL-70HI STSOP, Type I
85 IS62LV2568ALL-85BI mini BGA (6mm x 8mm)
IS62LV2568ALL-85TI TSOP, Type I
IS62LV2568ALL-85HI STSOP, Type I
ISSI
®
Integrated Silicon Solution, Inc.
2231 Lawson Lane
Santa Clara, CA 95054
Tel: 1-800-379-4774
Fax: (408) 588-0806
E-mail: sales@issi.com
www.issi.com
Loading...