Datasheet INA2133UA-2K5, INA2133UA, INA133U-2K5, INA133U, INA2133U-2K5 Datasheet (Burr Brown)

©1999 Burr-Brown Corporation PDS-1530A Printed in U.S.A. June, 1999

®

FEATURES

● DESIGNED FOR LOW COST

● SINGLE, DUAL VERSIONS

● LOW OFFSET VOLTAGE DRIFT:

±450µV max, ±5µV/°C max

● LOW GAIN ERROR: 0.05% max

● WIDE BANDWIDTH: 1.5MHz

● HIGH SLEW RATE: 5V/µs

● FAST SETTLING TIME: 5.5µs to 0.01%

● LOW QUIESCENT CURRENT: 950µA

● WIDE SUPPLY RANGE: ±2.25V to ±18V

● SO-8 and SO-14 PACKAGES

APPLICATIONS

● DIFFERENTIAL INPUT AMPLIFIER

BUILDING BLOCK

● DIFF IN / DIFF OUT AMPLIFIER

● UNITY-GAIN INVERTING AMPLIFIER

● GAIN = +1/2 OR G = +2 AMPLIFIER

● SUMMING AMPLIFIER

● SYNCHRONOUS DEMODULATOR

● CURRENT/DIFFERENTIAL LINE RECEIVER

● VOLTAGE-CONTROLLED CURRENT SOURCE

● BATTERY POWERED SYSTEMS

● LOW COST AUTOMOTIVE

DESCRIPTION

The INA133 and INA2133 are high slew rate, unity­gain difference amplifiers consisting of a precision op
amp with a precision resistor network. The on-chip
resistors are laser trimmed for accurate gain and high
common-mode rejection. Excellent TCR tracking of the
resistors maintains gain accuracy and common-mode
rejection over temperature. They operate over a wide
supply range, ±2.25V to ±18V (+4.5V to +36V single
supply), and input common-mode voltage range extends
beyond the positive and negative supply rails.

INA133

INA2133

High-Speed, Precision

DIFFERENCE AMPLIFIERS

International Airport Industrial Park • Mailing Address: PO Box 11400, Tucson, AZ 85734 • Street Address: 6730 S. Tucson Blvd., Tucson, AZ 85706 • Tel: [phone]

Twx: 910-952-1111 • Internet: http://www.burr-brown.com/ • Cable: BBRCORP • Telex: 066-6491 • FAX: [phone] • Immediate Product Info: [phone]

The differential amplifier is the foundation of many
commonly used circuits. The low cost INA133 and
INA2133 provide this precision circuit function without
using an expensive precision network.

The single version, INA133, package is the SO-8 surface
mount. The dual version, INA2133, package is the SO-14
surface mount. Both are specified for operation over the
extended industrial temperature range, –40°C to +85°C.
Operation is from –55°C to +125°C.

25kΩ 25kΩ

Sense

INA133

Output

V+

Ref

–In

+In

5

6

1

2

7

V–

4

3

25kΩ 25kΩ

Sense A

INA2133

Out A

V+

Ref A

–In A

+In A

12

13

14

2

11

V–

4

3

25kΩ 25kΩ

25kΩ 25kΩ

25kΩ 25kΩ

25kΩ 25kΩ

B

A

Sense B

Out B

Ref B

–In B

+In B

10

9

8

6

5

IN

A

13

3

IN

A2133

For most current data sheet and other product

information, visit www.burr-brown.com

2

®

INA133, INA2133

INA133U INA133UA

INA2133U INA2133UA

SPECIFICATIONS: VS = ±15V

At TA = +25°C, VS = ±15V, RL = 10kΩ connected to ground, and reference pin connected to ground, unless otherwise noted.

The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.

PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
OFFSET VOLTAGE

(1)

RTO

Initial

(1)

VCM = 0V ±150 ±450 ✻ ±900 µV

vs Temperature T

A

= –40°C to +85°C ±2 ±5 See Typical Curve µV/°C

vs Power Supply V

S

= ±2.25V to ±18V ±10 ±30 900 ±50 µV/V

vs Time 0.3 ✻ µV/√mo

Channel Separation (dual) dc 120 ✻ dB

INPUT IMPEDANCE

(2)

Differential 50 ✻ kΩ
Common-Mode V

CM

= 0V 25 ✻ kΩ

INPUT VOLTAGE RANGE

Common-Mode Voltage Range

Positive VO = 0V

2(V+) –3 2(V+) –2

✻✻ V

Negative V

O

= 0V

2(V–) +3 2(V–) +2

✻✻ V

Common-Mode Rejection Ratio

VCM = –27V to +27V, RS = 0Ω

80 90 74 ✻ dB

OUTPUT VOLTAGE NOISE

(3)

RTO
f = 0.1Hz to 10Hz 2 ✻ µVp-p
f = 10Hz 80 ✻ nV/√Hz
f = 100Hz 60 ✻ nV/√Hz
f = 1kHz 57 ✻ nV/√Hz

GAIN

Initial 1 ✻ V/V
Error V

O

= –14V to +13.5V ±0.02 ±0.05 ✻ ±0.1 %

vs Temperature T

A

= –40°C to +85°C ±1 ±10 ✻✻ppm/°C

Nonlinearity V

O

= –14V to +13.5V ±0.0001 ±0.001 ✻ ±0.002 % of FS

OUTPUT

Voltage Output Gain Error < 0.1%

Positive R

L

= 10kΩ to Ground (V+) –1.5 (V+)–1.3 ✻✻ V

Negative R

L

= 10kΩ to Ground (V–) +1 (V–)+0.8 ✻✻ V

Positive R

L

= 100kΩ to Ground (V+)–0.8 ✻ V

Negative R

L

= 100kΩ to Ground (V–)+0.3 ✻ V

Current Limit,

Continuous-to-Common

–25 /+32 ✻ mA

Capacitive Load (stable operation) 1000 ✻ pF

FREQUENCY RESPONSE

Small-Signal Bandwidth –3dB 1.5 ✻ MHz
Slew Rate 5 ✻ V/µs
Settling Time: 0.1% 10V Step, C

L

= 100pF 4 ✻ µs

0.01% 10V Step, C

L

= 100pF 5.5 ✻ µs

Overload Recovery Time 50% Overdrive 4 ✻ µs

POWER SUPPLY

Rated Voltage ±15 ✻ V
Operating Voltage Range

Dual Supplies ±2.25 ±18 ✻✻V
Single Supply +4.5 +36 ✻✻V

Quiescent Current (per amplifier) I

O

= 0 ±0.95 ±1.2 ✻✻mA

TEMPERATURE RANGE

Specification –40 +85 ✻✻°C
Operation –55 +125 ✻✻°C
Storage –55 +125 ✻✻°C
Thermal Resistance

θ

JA

SO-8 Surface Mount 150 ✻ °C/W
SO-14 Surface Mount 100 ✻ °C/W

✻ Specifications the same as INA133U, INA2133U.
NOTES: (1) Includes the effects of amplifier’s input bias and offset currents. (2) 25kΩ resistors are ratio matched but have ±20% absolute value. (3) Includes effects

of amplifier’s input current noise and thermal noise contribution of resistor network.

3

®

INA133, INA2133

INA133U INA133UA

INA2133U INA2133UA

SPECIFICATIONS: VS = ±5V

At TA = +25°C, VS = ±5V, RL = 10kΩ connected to ground, and reference pin connected to ground, unless otherwise noted.

Supply Voltage, V+ to V– .................................................................... 36V

Input Voltage Range ........................................................................ 2 • V

S

Output Short-Circuit (to ground)

(2)

.......................................... Continuous

Operating Temperature .................................................. –55 °C to +125°C

Storage Temperature ..................................................... –55°C to +125°C

Junction Temperature .................................................................... +150°C

Lead Temperature (soldering, 10s) ............................................... +300°C

NOTES: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may degrade
device reliability. (2) One channel per package.

ABSOLUTE MAXIMUM RATINGS

(1)

ELECTROSTATIC
DISCHARGE SENSITIVITY

This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with ap­propriate precautions. Failure to observe proper handling and
installation procedures can cause damage.

ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.

PACKAGE SPECIFIED
DRAWING TEMPERATURE PACKAGE ORDERING TRANSPORT

PRODUCT PACKAGE NUMBER

(1)

RANGE MARKING NUMBER

(2)

MEDIA

Single

INA133U SO-8 Surface Mount 182 –40°C to +85°C INA133U INA133U Rails

"""""INA133U/2K5 Tape and Reel

INA133UA SO-8 Surface Mount 182 –40°C to +85°C INA133UA INA133UA Rails

"""""INA133UA/2K5 Tape and Reel

Dual

INA2133U SO-14 Surface Mount 235 –40°C to +85°C INA2133U INA2133U Rails

"""""INA2133U/2K5 Tape and Reel

INA2133UA SO-14 Surface Mount 235 –40°C to +85°C INA2133UA INA2133UA Rails

"""""INA2133UA/2K5 Tape and Reel

NOTES: (1) For detailed drawing and dimension table, please see end of data sheet, or Appendix C of Burr-Brown IC Data Book. (2) Models with a slash (/ ) are
available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces of “INA133UA/2K5” will get a single
2500-piece Tape and Reel. For detailed Tape and Reel mechanical information, refer to Appendix B of Burr-Brown IC Data Book.

PACKAGE/ORDERING INFORMATION

PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
OFFSET VOLTAGE

(1)

RTO

Initial

(1)

VCM = 0V ±300 ±750 ✻ ±1500 µV

vs Temperature ±2 ✻ µV/°C

INPUT VOLTAGE RANGE

Common-Mode Voltage Range

Positive VO = 0V

2(V+) – 3 2(V+) – 2

✻✻ V

Negative V

O

= 0V

2(V–) +3 2(V–) + 2

✻✻ V

Common-Mode Rejection Ratio

VCM = –7V to +7V, RS = 0Ω

80 90 74 ✻ dB

GAIN

Initial 1 ✻ V/V
Gain Error V

O

= –4V to 3.5V ±0.02 ±0.05 ✻ ±0.1 %

Nonlinearity V

O

= –4V to 3.5V ±0.0001 ±0.001 ✻ ±0.002 % of FS

OUTPUT

Voltage Output Gain Error < 0.1%

Positive R

L

= 10kΩ to Ground (V+) –1.5 (V+) –1.3 ✻✻ V

Negative R

L

= 10kΩ to Ground (V–) +1 (V–) +0.8 ✻✻ V

Positive R

L

= 100kΩ to Ground (V+) –0.8 ✻ V

Negative R

L

= 100kΩ to Ground (V–) +0.3 ✻ V

POWER SUPPLY

Rated Voltage ±15 ✻ V
Operating Voltage Range

Dual Supplies ±2.25 ±18 ✻✻V
Single Supply +4.5 +36 ✻✻V

Quiescent Current (per amplifier) I

O

= 0 ±0.92 ±1.2 ✻✻mA

✻ Specifications the same as INA133U, INA2133U.
NOTES: (1) Includes the effects of amplifier’s input bias and offset currents.

4

®

INA133, INA2133

PIN CONFIGURATIONS

Top View SO-8 Top View SO-14

Ref

–In

+In

V–

NC

V+

Output

Sense

NC = No Connection

INA133

1

2

3

4

8

7

6

5

NC

–In A

+In A

V–

+In B

–In B

NC

Ref A

Out A

Sense A

V+

Sense B

Out B

Ref B

NC = No Connection

1

2

3

4

5

6

7

14

13

12

11

10

9

8

A

B

INA2133

5

®

INA133, INA2133

TYPICAL PERFORMANCE CURVES

At TA = +25°C, VS = ±15V, RL = 10kΩ connected to ground, and reference pin connected to ground, unless otherwise noted.

GAIN vs FREQUENCY

Frequency (Hz)

Closed-Loop Gain (dB)

10k 1M100k 10M

10

0

–10

–20

–30

–40

–50

VS = ±15V or ±5V

+125°C

+25°C

–55°C

COMMON-MODE REJECTION vs FREQUENCY

Frequency (Hz)

Common-Mode Rejection (dB)

100 100k1k 10k 1M

100

90

80

70

60

50

40

VS = ±15V or ±5V

POWER SUPPLY REJECTION vs FREQUENCY

Frequency (Hz)

Power Supply Rejection (dB)

1 100 1k 10k10 100k

120

100

80

60

40

20

–PSRR

+PSRR

CHANNEL SEPARATION vs FREQUENCY

Channel Separation (dB)

Frequency (Hz)

130

120

110

100

90

100 1k 10k 100k

INA2133

INPUT COMMON-MODE VOLTAGE

vs OUTPUT VOLTAGE

Output Voltage (V)

Common-Mode Voltage (V)

–15 0 5 10–5–10 15

40
30
20
10

0
–10
–20
–30
–40

VS = ±5V

VS = ±15V

TOTAL HARMONIC DISTORTION+NOISE

vs FREQUENCY

Frequency (Hz)

THD+N (%)

20 1k 10k100 20k

0.1

0.01

0.001

500kHz Filter

6

®

INA133, INA2133

TYPICAL PERFORMANCE CURVES (CONT)

At TA = +25°C, VS = ±15V, RL = 10kΩ connected to ground, and reference pin connected to ground, unless otherwise noted.

VOLTAGE NOISE DENSITY vs FREQUENCY

Frequency (Hz)

Voltage Noise (nV/√Hz)

1 10010 10k1k

1000

100

10

QUIESCENT CURRENT vs TEMPERATURE

Temperature (°C)

Quiescent Current (µA)

–75 –50 –25 25 50 75 1000 125

1400

1300

1200

1100

1000

900

800

700

Per Amplifier

SLEW RATE vs TEMPERATURE

Temperature (°C)

Slew Rate (V/µs)

–75 –50 –25 25 50 75 1000 125

7

6

5

4

3

–SR

+SR

VS = ±15V
V

S

= ±5V

SHORT-CIRCUIT CURRENT vs TEMPERATURE

Temperature (°C)

Short-Circuit |mA|

–75 –50 –25 25 50 75 1000 125

40

35

30

25

20

15

+I

SC

+I

SC

–I

SC

–I

SC

VS = ±15V
V

S

= ±5V

OUTPUT VOLTAGE SWING vs OUTPUT CURRENT

Output Current (mA)

Output Voltage (V)

0 ±5 ±10 ±20 ±25 ±30±15 ±35

–40°C

85°C

85°C

25°C

–40°C

(V+)

(V+) –5

(V+) –10

0

(V–) +10

(V–) +5

V–

25°C

0.1Hz TO 10Hz PEAK-TO-PEAK
VOLTAGE NOISE

500µs/div

1µV/div

7

®

INA133, INA2133

TYPICAL PERFORMANCE CURVES (CONT)

At TA = +25°C, VS = ±15V, RL = 10kΩ connected to ground, and reference pin connected to ground, unless otherwise noted.

OFFSET VOLTAGE PRODUCTION DISTRIBUTION

V

S

= ±15V

Percent of Units (%)

Offset Voltage (µV)

35

30

25

20

15

10

5

0

–900

–800

–700

–600

–500

–400

–300

–200

–100

0

100

200

300

400

500

600

700

800

900

Typical production
distribution of
packaged units.
Singles and duals
included.

OFFSET VOLTAGE PRODUCTION DISTRIBUTION

V

S

= ±5V

Percent of Units (%)

Offset Voltage (µV)

30

25

20

15

10

5

0

–1400

–1200

–1000

–800

–600

–400

–200

0

200

400

600

800

1000

1200

1400

Typical production
distribution of
packaged units.
Singles and duals
included.

OFFSET VOLTAGE DRIFT

PRODUCTION DISTRIBUTION

V

S

= ±15V

Percent of Units (%)

Offset Voltage Drift (µV/°C)

50
45
40
35
30
25
20
15
10

5
0

012345678910

Typical production
distribution of
packaged units.
Singles and duals
included.

OFFSET VOLTAGE DRIFT

PRODUCTION DISTRIBUTION

V

S

= ±5V

Percent of Units (%)

Offset Voltage Drift (µV/°C)

60

50

40

30

20

10

0

012345678910

Typical production
distribution of
packaged units.
Singles and duals
included.

SMALL-SIGNAL OVERSHOOT vs LOAD CAPACITANCE

Overshoot (%)

Load Capacitance (pF)

60

50

40

30

20

10

0

100 1k 10k 100k

VS = ±5V
V

S

= ±15V

+Overshoot

–Overshoot

–Overshoot

+Overshoot

SETTLING TIME vs LOAD CAPACITANCE

Capacitive Load (pF)

Settling Time (µs)

100 1k 10k

14

12

10

8

6

4

2

0

VS = ±15V
V

S

= ±5V

10V Step

0.1%

0.01%

8

®

INA133, INA2133

TYPICAL PERFORMANCE CURVES (CONT)

At TA = +25°C, VS = ±15V, RL = 10kΩ connected to ground, and reference pin connected to ground, unless otherwise noted.

MAXIMUM OUTPUT VOLTAGE vs FREQUENCY

Frequency (Hz)

Peak-to-Peak Output Voltage (V)

10k 100k 1M

32
28
24
20
16
12

8
4
0

VS = ±15V

VS = ±5V

SMALL-SIGNAL STEP RESPONSE

2.5µs/div

100mV/div

CL = 100pF

CL = 1000pF

LARGE-SIGNAL STEP RESPONSE

2.5µs/div

2V/div

CL = 1000pF

9

®

INA133, INA2133

APPLICATIONS INFORMATION

The INA133 and INA2133 are high-speed difference ampli­fiers suitable for a wide range of general purpose applica­tions. Figure 1 shows the basic connections required for
operation of the INA133. Decoupling capacitors are strongly
recommended in applications with noisy or high impedance
power supplies. The capacitors should be placed close to the
device pins as shown in Figure 1. All circuitry is completely
independent in the dual version assuring lowest crosstalk
and normal behavior when one amplifier is overdriven or
short-circuited.

As shown in Figure 1, the differential input signal is con­nected to pins 2 and 3. The source impedances connected to
the inputs must be nearly equal to assure good common­mode rejection. A 5Ω mismatch in source impedance will
degrade the common-mode rejection of a typical device to
approximately 80dB (a 10Ω mismatch degrades CMR to
74dB). If the source has a known impedance mismatch, an
additional resistor in series with the opposite input can be
used to preserve good common-mode rejection.

The INA133’s internal resistors are accurately ratio trimmed
to match. That is, R1 is trimmed to match R2 and R3 is
trimmed to match R4. However, the absolute values may not
be equal (R1 + R2 may be slightly different than R3 + R4).
Thus, large series resistors on the input (greater than 250Ω),
even if well matched, will degrade common-mode rejection.

Circuit board layout constraints might suggest possible varia­tions in connections of the internal resistors. For instance, it
appears that pins 1 and 3 could be interchanged. However,
because of the ratio trimming technique used (see paragraph
above) CMRR will be degraded. If pins 1 and 3 are inter-

changed, pins 2 and 5 must also be interchanged to maintain
proper ratio matching.

OPERATING VOLTAGE

The INA133 and INA2133 operate from single (+4.5V to
+36V) or dual (±2.25V to ±18V) supplies with excellent
performance. Specifications are production tested with ±5V
and ±15V supplies. Most behavior remains unchanged
throughout the full operating voltage range. Parameters which
vary significantly with operating voltage are shown in the
Typical Performance Curves.

INPUT VOLTAGE

The INA133 and INA2133 can accurately measure differen­tial signals that are above and below the supply rails. Linear
common-mode range extends from 2 • (V+)–3V to 2 • (V–)
+3V (nearly twice the supplies). See the typical performance
curve, “Input Common-Mode Voltage vs Output Voltage.”

OFFSET VOLTAGE TRIM

The INA133 and INA2133 are laser trimmed for low offset
voltage and drift. Most applications require no external offset
adjustment. Figure 2 shows an optional circuit for trimming
the output offset voltage. The output is referred to the output
reference terminal (pin 1), which is normally grounded. A
voltage applied to the Ref terminal will be summed with the
output signal. This can be used to null offset voltage as
shown in Figure 2. The source impedance of a signal applied
to the Ref terminal should be less than 10Ω to maintain good
common-mode rejection.

V

3

5

6

1

3

INA133

V

OUT

= V3 – V

2

Gain Error = ±0.01%
CMR = 90dB
Nonlinearity = ±0.0001%

2

R

3

25kΩ

R

4

25kΩ

R

1

25kΩ

R

2

25kΩ

V

2

–In

+In

1µF

V–

4

1µF

V+

7

FIGURE 1. Precision Difference Amplifier (Basic Power

Supply and Signal Connections).

V

3

5

6

3

V

O

INA133

V

O

= V3 – V

2

Offset Adjustment
Range = ±1mV

2

R

3

R

1

R

2

R

4

V

2

10

Ω

150k

Ω

10

Ω

100k

Ω

+15V

–15V

1

FIGURE 2. Offset Adjustment.

10

®

INA133, INA2133

TYPICAL APPLICATIONS

5

6

1

3

INA133

2

V

1

V

O

A

2

A

1

R

2

R

2

R

1

–In

V

2

+In

VO = (1 + 2R2/R1) (V2 –V1)

FIGURE 3. Precision Instrumentation Amplifier.

SIMILAR COMPLETE

A

1

, A

2

FEATURE BURR-BROWN IA

OPA2227 Low Noise INA103
OPA129 Ultra Low Bias Current (fA) INA116
OPA2277 Low Offset Drift, Low Noise INA114, INA128
OPA2130 Low Power, FET-Input (pA) INA121
OPA2234 Single Supply, Precision, Low Power INA122, INA118
OPA2237 Single Supply, Low Power, MSOP-8 INA122, INA126

The INA133 can be combined with op amps to form a complete instrumenta­tion amplifier with specialized performance characteristics. Burr-Brown offers
many complete high performance IAs. Products with related performances
are shown at the right in the table below.

100Ω

(1)

1%

V–

5

6

3

INA133

2

100Ω

(1)

1%

1

V

0

0 to 2V

I

IN

0 to 20mA

NOTE: (1) Input series resistors should be less than
250Ω (1% max mismatch) to maintain excellent CMR.
With 100Ω resistors, gain error is increased to 0.5%.

FIGURE 4. Current Receiver with Compliance to Rails.

5

6

2

VO = (V+)/2

INA133

V+

1

7

4

V+

CommonCommon

3

5

6

VO = –V

2

INA133

Gain Error = 0.05% maximum
Nonlinearity = 0.001% maximum
Gain Drift = 1ppm/°C

2

V

2

13

FIGURE 5. Pseudoground Generator.

FIGURE 6. Precision Unity-Gain Inverting Amplifier.

11

®

INA133, INA2133

V

1

5

6

1

3

VO = 2 • V

1

INA133

Gain Error = 0.025% maximum
Gain Drift = 2ppm/°C

2

V

3

5

6

3

2

INA133

1

VO =

V

3

2

±0.05% max

(V1 + V3)

2

VO =

±0.05% max

V

1

5

6

1

3

2

INA133

V

3

VO = V1 + V

3

±0.05% max

V

1

5

6

1

3

INA133

2

V

3

5

6

1

3 Ref

2

Output

INA133

Voltage

Source

(1)

Device
VFC320
VFC100
DAC80
DAC703
XTR110

Output
0-10kHz
0-F

CLOCK

/2
0-FS (12 bits)
0-FS (16 bits)
4-20mA

Ref must be driven
by low impedance.

NOTE: (1) Unipolar Input Device.

OPA277

V

1

6

1

3

V

O

INA133

V

3

25

R

1

R

2

VO = 1 +

R

2

R

1

V1 + V

3

2

( )( )

For G = 10,

See INA143.

FIGURE 7. Precision Gain = 2 Amplifier. FIGURE 8. Precision Gain = 1/2 Amplifier.

FIGURE 9. Precision Average Value Amplifier.

FIGURE 10. Precision Summing Amplifier.

FIGURE 11. Precision Bipolar Offsetting. FIGURE 12. Precision Summing Amplifier with Gain.

12

®

INA133, INA2133

Shield

5

6

1

2

INA133

A

1

A

2

11

12

A

3

Output

G = 1 +

50kΩ

R

G

Feedback

3

Noise (60Hz hum)

Noise (60Hz hum)

Transducer or
Analog Signal

13 7

V+ V–

8 Ref10

25kΩ

25kΩ

25kΩ

25kΩ

INA115

1

25k

Ω

25k

Ω

4

2

3

14

15

5

R

G

100k

Ω

V

1

12

13

A

3

14

1/2 INA2133

2

V

2

V

3

10

9

5

8

VO = V3 + V4 – V1 – V

2

1/2 INA2133

6

V

4

B

FIGURE 13. Instrumentation Amplifier Guard Drive Generator.

FIGURE 14. Precision Summing Instrumentation Amplifier.

13

®

INA133, INA2133

FIGURE 15. Precision Voltage-to-Current Converter with

Differential Inputs.

5

6

3

INA133

2

1

V

1

V

2

Load

IO = (V1 – V2) (1/25k + 1/R)

I

O

R

R

5

6

3

INA133

2

1

V

3

V

2

Load

I

O

= (V3 – V2)/R

I

O

R

OPA131

FIGURE 16. Differential Input Voltage-to-Current Con-

verter for Low I

OUT

.

5

6

3

INA133

2

1

V

3

V

2

Load I

O

R

R

Gate can be

+V

S

–5V

I

O

= (V3 – V2) (1/25k + 1/R)

R < 200Ω

12

13

3

1/2 INA2133

2

V

01

14

10

9

5

1/2 INA2133

A

B

6

V

01

– V

02

= 2 (V2 – V1)

V

02

8

V

2

V

1

5

6

3

INA133

2

1

V

3

V

2

Load I

O

R

Gate can be

+V

CC

–5V

I

O

=

(V

3

– V2)

R

(R ≥ 200Ω)

FIGURE 17. Isolating Current Source.

FIGURE 18. Differential Output Difference Amplifier.

FIGURE 19. Isolating Current Source with Buffering Am-

plifier for Greater Accuracy.

14

®

INA133, INA2133

FIGURE 20. Differential Input Data Acquisition.

5

6

1

INA133

ADS7806

2

3

4

7

+5V

V

S

12 Bits

Out

0V-4V

Input

Transducer

or
Analog
Signal

–5V

Eliminates errors due to different grounds.

5

6

3

1

INA133

2

1

V

O

DG188

V

1

Logic

In

Logic In

0
1

V

O

–V

1

+V

1

V

1

Input

5

6

3

1

V0 = |V1|

INA133

2

R

4

R

3

R

1

R

2

OPA130

10pF

D

1

D

2

R

5

2k

Ω

FIGURE 21. Digitally Controlled Gain of ±1 Amplifier.

FIGURE 22. Precision Absolute Value Buffer.

15

®

INA133, INA2133

5

6

1

3

INA133

2

4

2

+15V

6

–10V Out

+10V Out

REF102

5

7

6

3

V

3

INA133

2

4

V

2

1

4

2

+15V

OPA227

REF102

6
10V

IO = 4 to 20mA

0V to 10V

In

12.5kΩ 1kΩ

50kΩ

R

LOAD

V+

Set R

1

= R

2

R

2

50.1Ω

R

1

50.1Ω

2N3904

25kΩ25kΩ

25kΩ25kΩ

For 4-20mA applications,

the REF102 sets the 4mA

low-scale output for 0V input.

IO = V3 – V

2

+

1

25kΩ1R

2

FIGURE 25. Precision Voltage-to-Current Conversion.

FIGURE 23. ±10V Precision Voltage Reference. FIGURE 24. High Output Current Precision Difference

Amplifier.

5

6

1

INA133

BUF634

2

3

V

O

R

L

–In

+In

BUF634 inside feedback
loop contributes no error.