Datasheet HIP7030A2 Datasheet (Intersil Corporation)

Download

Page 1

ADVANCE INFORMATION

August 1996

HIP7030A2

J1850 8-Bit 68HC05 Microcontroller

Features

• Fully Supports VPW Speciﬁcations of SAE J1850 Standard for Class B Data Communications Network Interface

• On-Chip Memory

• 176 Bytes of RAM

• 2110 Bytes of User ROM

• 13 Bidirectional I/O Lines

• 16-Bit Timer with Capture and Compare Registers

• Serial Peripheral Interface (SPI) System

• Watchdog Timer and Slow Clock Detect

• 10MHz Operating Frequency (5.0MHz Internal Bus Frequency) at 5V

• Built-In-Test Bootstrap Mode with 242 Bytes of ROM

• Two Channel Analog Comparator

• On-Chip Oscillator Ampliﬁer

• 8-Bit CPU Architecture

• Power-Saving STOP, WAIT and Data Retention Modes

• Full -40

• Single 3.0V to 6.0V Supply

• 28 Lead Dual-In-Line and Small Outline Plastic Packages

C to 125oC Operating Range

Software Features

• Standard 68HC05 Instruction Set

• True Bit Manipulation

• Addressing Modes Include Indexed Addressing

- Memory Mapped I/O

Ordering Information

TEMP.

PART NUMBER

HIP7030A2P -40 to 125 28 Lead Plastic

HIP7030A2M -40 to 125 28 Lead Plastic

RANGE (oC) PACKAGE

DIP

SOIC (W)

PKG.

NO.

M28.3

E28.6

Description

The HIP7030A2 HCMOS Microcomputer is a member of the CDP68HC05 family of low-cost single-chip microcomputers. The integrated hardware functions provide the system designer with a complete set of building blocks for implementing a “Class B” multiplexed communications network interface, which fully conforms to the VPW Multiplexed Wiring protocol speciﬁed in SAE Recommended Practice J1850. This 8-bit microcomputer unit (MCU) contains an onchip oscillator, CPU, 176 bytes of RAM, 2110 bytes of user ROM, 13 I/O lines, a J1850 Variable Pulse Width Symbol Encoder/Decoder (VPW SENDEC) system, a Serial Peripheral Interface (SPI) system, a two channel analog Comparator, a Watchdog Timer, a Slow Clock Detect, and a 16-bit Timer. The static HCMOS design allows operation at input frequencies up to 10MHz (5MHz internal clock).

Table of Contents

Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

MCU Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Electrical & Timing Speciﬁcations. . . . . . . . . . . . . . . . . . . . . 3

Functional Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Integrated Hardware I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Memory. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Memory Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Built-In Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Resets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Vector Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Programmable Timer

Counter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Serial Peripheral Interface (SPI) . . . . . . . . . . . . . . . . . . . . . . 27

J1850 VPW Messaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Symbol Encoder Decoder

Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

COP System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Effects of STOP and WAIT Modes . . . . . . . . . . . . . . . . . . . . 41

Instruction Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Package Outline Dimensions . . . . . . . . . . . . . . . . . . . . 55 - 56

Opcode Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

I/O, Control, Status and Data Register Deﬁnitions. . . . . . . 52

Ordering

Information Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Ordering Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207

File Number 3646.2

Page 2

Block Diagram

TCMP

TCAP

PA0

PA1

PA2

PA3

PA4

PA5

PA6

PORT A I/O LINES

PD2, V2 PD3, V3

PD4, VR

PORT D I/O LINES

PA7

PD0 PD1

TCAP

21 20 19 18

VSS22 VDD7

TIMER SYSTEM

PORT

REG

PORT D

REG

PORT D

SFR REG

DAT A

DIR

REG

PORT D

DIR

REG

HIP7030A2

INTERNAL

PROCESSOR

CLOCK

ACCUMULATOR

INDEX

CONDITION CODE

STACK

POINTER

PROGRAM

COUNTER HIGH

PROGRAM

COUNTER LOW

2110 x 8

ROM

242 x 8

BUILT-IN-TEST

ROM

OSCIN OSCOUT

2324

OSCILLATOR

AND

÷ 2

PCH

PCL

176 x 8

STATIC RAM

OSCB

CPU

CONTROL

CPU

ALU

WATCHDOG AND

SLOW CLOCK DETECT

RESET

IRQ

SYMBOL INT

VPW SYMBOL

ENCODER /

DECODER AND

ARBITRATION

SPI

SYSTEM

INTERNAL PROCESSOR

CLOCK

4 3

25 26 27 28

VPW OUT VPW IN

SCK MOSI MISO SS

Pinout

TCAP

TCMP

VPW IN

VPW OUT

RESET

IRQ

PA7 PA6 PA5 PA4 PA3 PA2 PA1

1 2 3 4 5 6 7 8

9 10 11 12 13 14

HIP7030A2

(PDIP, SOIC)

TOP VIEW

SS MISO

27 26

MOSI

SCK OSCIN

24 23

OSCOUT V

PD0

21 20

PD1 PD2, V2

PD3, V3

18 17

PD4, VREF

OSCB PA0

Page 3

HIP7030A2

Absolute Maximum Ratings Thermal Information

Supply Voltage (VDD). . . . . . . . . . . . . . . . . . . . . . . . . -0.3V to +7.0V

Input or Output Voltage

Pins with VDD Diode. . . . . . . . . . . . . . . . . . . . -0.3V to VDD+0.3V

Pins without VDD Diode . . . . . . . . . . . . . . . . . . . . . -0.3V to +10V

Current Drain Per Pin, I (Excluding VDD and VSS) . . . . . . . . 25mA

Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . +265oC

ESD Classiﬁcation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Class 2

Gate Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9000 Gates

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

Operating Conditions

Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . +3.0V to +5.5V

Operating Temperature Range. . . . . . . . . . . . . . . . .-40oC to 125oC

Input Low Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to +0.8V

Thermal Resistance (Typical) θ

Plastic DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . .60oC/W

Plastic SOIC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . 75oC/W

Maximum Package Power Dissipation at +125oC

DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 415mW

SOIC Package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .325mW

Operating Temperature Range (TA) . . . . . . . . . . . .-40oC to +125oC

Storage Temperature Range (T

). . . . . . . . . . . .-65oC to +150oC

STG

Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +150oC

Input High Voltage. . . . . . . . . . . . . . . . . . . . . . . . ..(0.8•VDD) to V

Input Rise and Fall Time

CMOS Inputs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100ns Max.

CMOS Schmitt Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . .Unlimited

DC Electrical Speciﬁcations V

= 5VDC±10%, VSS = 0VDC, TA = -40oC to +125oC Unless Otherwise Speciﬁed

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

No Load Output Voltage V

Output High Voltage: PA0-7, PD0-4, VPWOUT, TCMP

Output High Voltage: OSCOUT V Output High Voltage: MISO, MOSI, SCK, OSCB V Output Low Voltage: OSCOUT V Output Low Voltage: MISO, MOSI, SCK, OSCB V Input High Voltage: PA0-7, PD0-4, MISO, MOSI,

SS, SCK Input High Voltage: RESET, IRQ, TCAP,

VPWIN, OSCIN Input Low Voltage: PA0-7, PD0-4, MISO, MOSI,

SS, SCK Input Low Voltage: RESET,IRQ, TCAP,VPWIN,

OSCIN Input Hysteresis Voltage: RESET, IRQ, TCAP,

VPWIN, OSCIN Supply Current

RUN I WAIT (Note 2) I STOP (Notes 2, 3) I

I/O Ports Hi-Z Leakage Current: PA0-7, PD0-4, MISO, MOSI, SCK

Input Current: RESET, IRQ, TCAP, OSCIN, VPWIN, SS

OH OH

HYS

RUN WAIT STOP

< ±10µA - - 0.1 V

LOAD

VDD-0.1 - - V

= -0.8mA VDD-0.8 VDD-0.4 - V

LOAD

= -0.08mA VDD-0.8 VDD-0.4 - V

LOAD

= -1.6mA VDD-0.8 VDD-0.4 - V

LOAD

= 0.17mA - 0.2 0.4 V

LOAD

= 1.6mA - 0.2 0.4 V

LOAD

= 10MHz Exter-

OSC

nal Square Wave

0.7•V

0.8•V

0.1•V

- 8 18 mA

- 3.2 10 mA

-VDDV

- 0.3•V

- 0.2•V

1.0 0.5•V

TA = 25oC-250µA TA = -40oC to 125oC - 10 250 µA

-10 ±0.01 +10 µA

-1 .001 +1 µA

Page 4

HIP7030A2

DC Electrical Speciﬁcations V

= 5VDC±10%, VSS = 0VDC, TA = -40oC to +125oC Unless Otherwise Speciﬁed (Continued)

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Capacitance: (Note 4) C

Powerdown Input Voltage: RESET, IRQ,

OUT

INPD

VDD = 0 -0.3 - 7 V

- - 12 pF

--8pF

VPWIN, OSCIN Comparator:

Input Voltage: V2, V3, V

REF

VSS-0.2 - V

+0.02

Input Current: V2, V3, V

REF

Offset Voltage V Response t

OFF

-1 - +1 µA

-20-mV

-2-µs

NOTES:

1. This device contains circuitry to protect the inputs against damage due to high static voltages of electric ﬁelds; howe ver, it is advised that normal precautions be taken to avoid application of any voltage higher than maximum rated voltages to this high impedance circuit. For proper operation it is recommended that VIN and V

be constrained to the range VSS<(VIN or V

OUT

)<VDD. Reliability of operation is

OUT

enhanced if unused inputs are connected to an appropriate logic voltage level (e.g., either VSS or VDD).

2. WAIT, STOP IDD: All ports configured as inputs, VIL = 0.2V and VIH = VDD - 0.2V.

3. STOP IDD measured with OSCIN = VSS, no feedback resistor connected.

4. Includes Ports used as Input/Output Pins, Ports used as Input only Pins; Ports used as Output only Pins.

Control Timing V

= 5VDC±10%, VSS = 0VDC, TA = -40oC to 125oC Unless Otherwise Speciﬁed

PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS

Frequency Of Operation

Crystal Option f External Clock Option f

OSC OSC

Internal Operating Frequency

Crystal (f

External Clock (f Cycle Time t Crystal Oscillator Start-up Time for AT-cut Crystal t Stop Recovery Start-up Time (AT-cut Crystal

+2) f

OSC

+2) f

OSC

OP OP

CYC

OXOV

ILCH

Oscillator) RESET Pulse Width t

Timer

Resolution (Note 1) t

Input Capture Pulse Width tTH, t

Input Capture Pulse Period tTL, t Interrupt Pulse Width Low (Edge-Triggered) t OSC1 Pulse Width tOH, t Slow Clock Detect Frequency Range f

RES

TL TL

ILIH

SLOW

NOTES:

1. Since a 2-bit prescaler in the timer must count four internal cycles (t resolution.

2. The minimum period t 24 t

CYC

should not be less than the number of cycle times it takes to execute the capture interrupt service routine plus

TLTL

1 - 10 MHz 1 - 10 MHz

0.5 - 5 MHz

200 - - ns

- - 100 ms

1.5 - - t

4--t

50 - - ns

(Note 2) - - t

50 - - ns 35 - - ns 20 50 200 KHz

), this is the limiting minimum factor in determining the timer

CYC

Page 5

HIP7030A2

Serial Peripheral Interface (SPI) Timing (See Figure 3) V

= 5VDC±10%, VSS = 0VDC, TA = -40oC to 125oC

Unless Otherwise Speciﬁed

NUMBER PARAMETER SYMBOL MIN MAX UNITS

Operating Frequency

Master f

OP(M)

0.03 0.5 f

(Note 3)

Slave f

OP(S)

DC 5 MHz

1 Cycle Time

Master t Slave t

CYC(M) CYC(S)

2- t

CYC

200 - ns

2 Enable Lead Time

Master t Slave t

LEAD(M) LEAD(S)

(Note 1) - -

50 - ns

3 Enable Lag Time

Master t Slave t

LAG(M) LAG(S)

(Note 1) - -

50 - ns

4 Clock (SCK) High Time

Master t Slave t

W(SCKH)M W(SCKH)S

200 - ns

50 - ns

5 Clock (SCK) Low Time

Master t Slave t

W(SCKL)M

W(SCKL)S

200 - ns

50 - ns

6 Data Setup Time (Inputs)

Master t Slave t

SU(M)

SU(S)

50 - ns 50 - ns

7 Data Hold Time (Inputs)

Master t Slave t

H(M)

H(S)

50 - ns 50 - ns

8 Access Time (Time to Data Active from High Impedance State)

Slave t

0 120 ns

9 Disable Time (Hold Time to High Impedance State)

Slave t

DIS

- 200 ns

10 Data Valid Time

Master (Before Capture Edge) t Slave (After Enable Edge) (Note 2) t

V(M)

V(S)

0.25 - t

- 150 ns

CYC(M)

11 Data Hold Time (Outputs)

Master (After Capture Edge) t Slave (After Enable Edge) t

HO(M) HO(S)

0.25 - t

CYC(M)

0-ns

12 Rise Time (VDD = 20% to 70%, CL = 100pF)

SPI Outputs (SCK, MOSI, MISO) t SPI Inputs (SCK, MOSI, MISO, SS) t

R(M)

R(S)

-50ns

-2µs

13 Fall Time (VDD = 20% to 70%, CL = 100pF)

SPI Outputs (SCK, MOSI, MISO) t SPI Inputs (SCK, MOSI,MISO, SS) t

F(M) F(S)

-50ns

-2µs

NOTES:

1. Signal Production depends on software.

2. Assumes 200pF load on all SPI pins.

3. Note that the units this specification uses is fOP (internal operating frequency), not MHz! In the master mode the SPI bus is capable of running at one-half of the devices’s internal operating frequency, therefore, 2.5MHz maximum.

Page 6

Control Timing Diagrams

OSC1

(NOTE 1)

ILIH

RESET

IRQ

HIP7030A2

ILCH

INTERNAL

CLOCK

INTERNAL

ADDRESS

BUS

NOTE:

1. Represents the internal gating of the OSC1 pin.

FIGURE 1. STOP RECOVERY TIMING DIAGRAM

EXTERNAL

(TCAP PIN 1)

FIGURE 2.

Serial Peripheral Interface (SPI) Timing Diagrams

TLTL

4064 t

CYC

1FFE

RESET OR INTERRUPT VECTOR FETCH

SS (INPUT)

SCK (OUTPUT)

MISO (INPUT)

MOSI (OUTPUT)

HELD HIGH ON MASTER

(1)

(6)

(4)

D7I D6I D0I

(7)

D7O D6O D0O

(11)(10)

(5)

FIGURE 3A. SPI MASTER TIMING CPOL = 0, CPHA = 1

(12)(13)

Page 7

HIP7030A2

Serial Peripheral Interface (SPI) Timing Diagrams

HELD HIGH ON MASTER

SS (INPUT)

SCK (OUTPUT)

MISO (INPUT)

MOSI (OUTPUT)

SS (INPUT)

SCK (OUTPUT)

(4)

D7I D6I D0I

(6)

(7)

D7O D6O D0O

(11)(10)

FIGURE 3B. SPI MASTER TIMING CPOL = 1, CPHA = 1

HELD HIGH ON MASTER

(1)

(5)

(1)

(Continued)

(12)(13)

MISO (INPUT)

MOSI (OUTPUT)

SS (INPUT)

SCK (OUTPUT)

MISO (INPUT)

MOSI (OUTPUT)

(6)

(4)

D7I D6I D0I

(7)

D7O D6O D0O

(11)(10)

(5)

FIGURE 3C. SPI MASTER TIMING CPOL = 0, CPHA = 0

HELD HIGH ON MASTER

(1)

(6)

(5)

D7I D6I D0I

(7)

D7O D6O D0O

(11)(10)

(4)

(12)(13)

NOTE:

1. Measurement points are VOL, VOH, VIL and V

FIGURE 3D. SPI MASTER TIMING CPOL = 1, CPHA = 0

IH.

Page 8

HIP7030A2

Serial Peripheral Interface (SPI) Timing Diagrams

SS (INPUT)

SCK (INPUT)

MISO (OUTPUT)

MOSI (INPUT)

SS (INPUT)

SCK (INPUT)

HIGH Z

(4)(2)

LAST

TRANSMITTED

(8)

BIT

FIGURE 3E. SPI SLAVE TIMING CPOL = 0, CPHA = 1

LAST BIT TRANSMITTED

(1)

(13)

(5)

D7O D6O D0O

D7I D6I D0I

(7)(6)

(1)(5)(2)

(4)

(Continued)

(12)

(3)

(9)(11)(10)

(3)

(13)(12)

MISO (OUTPUT)

MOSI (INPUT)

NOTE:

1. Measurement points are V

(INPUT)

SCK

(INPUT)

MISO

(OUTPUT)

MOSI

(INPUT)

(8)

, VOH, VIL and VIH.

FIGURE 3F. SPI SLAVE TIMING CPOL = 1, CPHA = 1

(2)

(8)

D7O D6O D0O

D7I D6I D0I

(7)(6)

(1)

(13)

(4)

D7O D6O D0O

D7I D6I D0I

(10)

(5)

(11)

(12)

(9)(11)(10)

(3)

(9)

(6)

(7)

FIGURE 3G. SPI SLAVE TIMING CPOL = 0, CPHA = 0

Page 9

HIP7030A2

Serial Peripheral Interface (SPI) Timing Diagrams

(INPUT)

(2)

SCK

(INPUT)

MISO

(OUTPUT)

(8)

MOSI

(INPUT)

(6)

NOTE:

1. Measurement points are VOL, VOH, VIL and V

FIGURE 3H. SPI SLAVE TIMING CPOL = 1, CPHA = 0

(5)

D7O

(10)

D7I

(7)

IH.

(1)

(12) (13) (3)

(4)

D6O D0O

D6I

(Continued)

(11)

(9)

D0I

Functional Pin Description

This section provides a description of each of the 28 pins of the HIP7030A2 MCU.

and VSS (Power)

Power is supplied to the MCU using these two pins. V connected to the positive supply and V

is connected to

the negative supply.

IRQ (Maskable Interrupt Request - Input)

IRQ pin is negative edge-sensitive triggering. A high to

The low transition on the

IRQ pin will produce an interrupt.

In the event of an interrupt request, the MCU always completes the current instruction before it responds to the request. An internal mask can be used to inhibit the MCU from responding to IRQ interrupts.

An IRQ interrupt is generated if the at least one t

. The occurrence of the low going pulse is

ILIH

IRQ pin is pulled low for

registered in a ﬂip-ﬂop and the IRQ interrupt will be recognized even if the

IRQ pin has returned to a high state before

the interrupt can be serviced. Once the edge-sensitive ﬂip-ﬂop is cleared, (it is automati-

cally cleared at the start of the interrupt ser vice routine) the interrupt request is removed until the

IRQ pin returns to a

high level and once again goes low. See

INTERRUPTS

for more details concerning IRQ inter-

rupts.

RESET (Master Reset - Input)

The HIP7030A2 contains an integrated Power-On Reset (POR) circuit and the

RESET input is therefore not required for start-up. It can be used to reset the MCU internal state and provides for an orderly re-start of the software after initial power-up. Refer to POR and

RESET.

Resets

for a detailed description of

TCAP (Timer Capture - Input)

The TCAP input controls the input capture feature for the onchip programmable timer system. The TCAP input is also used as the strobe signal to the Port D strobed outputs. Refer to

put Mode

Input Capture Register

and

for additional information.

PD0, PD1 Strobed Out-

TCMP (Timer Compare - Output)

The TCMP pin provides an output for the output compare feature of the on-chip timer system. Refer to

pare Register

for additional information.

Output Com-

OSCIN (Oscillator Input - Input), OSCOUT (Oscillator Output - Output), OSCB (Oscillator Buffered Output - Output)

OSCIN is the input and OSCOUT is the output of an inverter/ampliﬁer which can be used to build either a quartz crystal or ceramic resonator based clock oscillator. Alternatively, the OSCIN input can be driven from any external clock source which satisﬁes the CMOS Schmitt trigger input level requirements of the OSCIN pin. See

Electrical Speciﬁcations

for input level speciﬁcation.

Page 10

HIP7030A2

OSCB is a squared, buffered version of the OSCIN signal, available for driving one external CMOS load.

The fundamental internal clock is derived by a divide-by-two of the external oscillator frequency (f clocks are also derived from the external frequency. These clocks include the input to the 16-bit Timer, the Serial Clock (SCK), and the VPW Symbol Encoder/Decoder (SENDEC).

Quartz Crystal

The circuit shown in Figure 4A is recommended when using a quartz crystal. The inter nal oscillator is designed to interface with an AT -cut parallel resonant quartz crystal in the frequency range speciﬁed for f

OSC

in Figure 4B lists the recommended capacitance and feedback resistance values. Use of an external CMOS oscillator is recommended when crystals outside the speciﬁed ranges are to be used. The crystal and components should be mounted as close as possible to the OSCIN and OSCOUT pins to minimize output distortion and start-up stabilization time.

Ceramic Resonator

A ceramic resonator may be used in place of the crystal in cost sensitive applications. The circuit in Figure 4A is recommended when using a ceramic resonator. Figure 4C lists the recommended capacitance and feedback resistance values. The manufacturer of the particular ceramic resonator being considered should be consulted for speciﬁc information.

External Clock

). All other internal

OSC

Electrical Speciﬁcations

10MHz UNITS

(Typical) 5.5 Ω

OUT

Q 500 -

NOTES:

1. When no power is applied to the HIP7030A2, the OSCIN,IRQ, RESET, and VPWIN pins can have up to 9VDC applied with no side effects.

2. When power is applied to the HIP7030A2, it is recommended that all unused inputs, except Port A and Port D I/O lines configured as outputs, be tied to an appropriate logic level (i.e., either V or VSS).

FIGURE 4C. CERAMIC RESONATOR PARAMETERS

35 pF

5pF 22 pF 22 pF

1-5 MΩ

If an external clock is used, it should be applied to the OSCIN input with the OSCOUT output not connected, as shown in Figure 4E. The t

OXOV

or t

speciﬁcations do

ILCH

not apply when using an external clock input. The equivalent speciﬁcation of the external clock source should be used in lieu of t

FIGURE 4A. CRYSTAL/RESONATOR CIRCUIT CONNECTIONS

RS (Max) 400 75 50 30 Ω C

OUT

Q 303030 30 K

or t

OXOV

FIGURE 4B. QUARTZ CRYSTAL PARAMETERS

ILCH

MCU

OSCIN OSCOUT

2MHz 4MHz 8MHz 10MHz UNITS

575 5pF

0.008 0.012 0.015 0.018 µF 15-40 15-30 12-30 12-30 pF 15-30 15-25 12-25 12-25 pF

1-10 1-10 1-10 1-10 MΩ

OUT

FIGURE 4D. CRYSTAL/RESONATOR EQUIVALENT CIRCUIT

MCU

OSCIN OSCOUT

24 23

UNCONNECTED

FIGURE 4E. EXTERNAL CLOCK SOURCE CONNECTIONS

EXTERNAL CLOCK

PA0-PA7 (Port A - Input/Output)

These eight I/O lines comprise Port A. The mode (i.e., input or output) of each pin is software programmable. All Port A I/Os are conﬁgured as inputs during a POR, COP, or external reset. Refer to

Port A

under

Port A and D I/O Lines

for a

detailed description of programming the Port A I/O lines.

PD0-PD4 (Port D - Input/Output)

These ﬁve I/O lines comprise Port D. As with PA0-PA7, the mode (i.e., input or output) of each pin is software programmable. In addition, a Special Function Register (SFRD) allows conﬁguring PD0 and PD1 as “strobed” outputs, and/or PD2, PD3, and PD4 as inputs to an on-chip analog comparator.

Page 11

HIP7030A2

All Port D I/Os are conﬁgured as inputs during a POR, COP, or external reset. Refer to

Lines

under

Port A and D I/O Lines

PD0-PD4 Special Function I/O

for a detailed description

of programming the Port D I/O lines.

VPWOUT (Variable Pulse Width Out - Output), VPWIN (Variable Pulse Width In - Input)

These two lines are used to interface to the J1850 bus transceiver .

VPWOUT is the pulse width modulated output of the SENDEC encoder block.

VPWIN is the inverted input to the SENDEC decoder block.

VPW Symbol Encoder/Decoder (SENDEC)

See

for a

detailed description of the J1850 interface pins.

MISO (Master-in/Slave-out - Input/Output), MOSI (Master-out/Slave-in - Input/Output), SCK (Serial Clock - Input/Output), SS (Slave Select - Input)

These four lines constitute the Serial Peripheral Interface (SPI) communications port. The MCU can be conﬁgured as a SPI “master” or as a SPI “slave”. In master mode MOSI and SCK function as outputs and MISO functions as an input. In slave mode MOSI and SCK are inputs and MISO is an output.

SS is always an input.

Serial data words are transmitted and received over the MISO/MOSI lines synchronously with the SCK clock stream. The word size is ﬁxed at 8-bits. Single buffering is used which results in an inherent inter-byte delay. The master device always provides the synchronizing clock.

A low on the

SS line causes the MCU to immediately assume the role of slave, regardless of it’s current mode. This allows multi-master systems to be constructed with appropriate arbitration protocols.

See the detailed discussion of the SPI interface under

Peripheral Interface (SPI)

Serial

Integrated Hardware I/O Functions

PORT A

Each of the Parallel Port pins of Port A may be individually programmed as an input or an output under software control. The direction of each pin is determined by the state of the corresponding bit in the Port A Data Direction Register (DDRA, location $04).

PORT DATA

PORT DRR

INTERNAL LOGIC

PAD

DAT A

DIR REG

BIT

LATCHED

OUTPUT

DATA BIT

INTERNAL CONNECTIONS

FIGURE 5B. PORT A FUNCTIONAL BLOCK DIAGRAM

76543210

DA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0

PORT A DATA DIRECTION REGISTER (DDRA, LOCATION $04)

INPUT REG BIT

OUTPUT

INPUT I/O

I/O

Any Port A pin is conﬁgured as an output if its corresponding DDR bit is set to a logic one. A pin is conﬁgured as an input if its corresponding DDR bit is cleared to a logic zero. Any reset will clear all DDR bits, which conﬁgures all Port A and D pins as inputs. The data direction register is capable of being written to or read by the processor. Refer to Figure 5 and Table 1.

76543210

A7 A6 A5 A4 A3 A2 A1 A0

PORT A DATA REGISTER (PORTA, LOCATION $00)

Port A is an 8-bit wide read-write data register. Regardless of the state of the DDRA bits, all Port A data latches are modiﬁed with each write to Port A. When Port A is read, the value read for bits progr ammed as outputs , is the contents of the data latch, not the pin. The value read for bits programmed as inputs is the value on the pin.

TABLE 1. PORT A TRUTH TABLE

(NOTE 1)

R/W DDR I/O PIN FUNCTION

W 0 The I/O pin is in input mode.

Data is written into the output data latch

W 1 Data is written into the output data latch

and simultaneously output to the I/O pin. R 0 The state of the I/O pin is read. R 1 The I/O pin is in output mode.

The output data latch is read.

NOTE:

1. R/W is an internal signal which equals R when reading the Port Data Register and equals W when writing the Port Data Register.

PD0-PD4 SPECIAL FUNCTION I/O LINES

These ﬁve lines comprise Port D. The ﬁve lines can be individually programmed to provide input or output capabilities similar to the eight Port A lines. Additionally, each of the lines

FIGURE 5A. PORT A I/O PAD CIRCUITRY

Page 12

HIP7030A2

can be programmed to provide special capabilities, beyond the standard digital input and output functions. The PD0PD4 I/O lines are controlled via three read/write registers.

76543210 0 0 0 DD4 DD3 DD2 DD1 DD0

PORT D DATA DIRECTION REGISTER (DDRD, LOCATION $07)

DDRD contains ﬁve data direction bits, DD0-DD4, which control whether the associated I/O line behaves as an Input or as an Output. Setting a data direction bit causes the related I/O line to be conﬁgured as an output, while clearing the bit causes the line to be conﬁgured as an input. When conﬁgured as an output, the I/O line is actively driven by the HIP7030A2. When conﬁgured as an input, the I/O line appears as a high impedance input and should be driven by external circuitry.

DDRD bits D0-D4 are cleared by RESET.

7 6 5 43210

CMP3 CMP2 0 D4 D3 D2 D1 D0

PORT D DATA REGISTER (PORTD, LOCATION $03)

PortD is an 8-bit wide register with 5 read/write data bits and 2 read-only bits. When writing to PortD, bits 5-7 are ignored. All other bits (D0-D4) are stored in latches until they are explicitly modiﬁed with a subsequent write (or read-modifywrite) instruction. The utilization of bits D0-D4 is dependent on the value in the associated DDRD bit. If a line is programmed as an input, the value read in PortD (D0-D4) is the logic level present on the external I/O line. If a line is programmed as an output, the value read in PortD (D0-D4) is the value last written to the same bit in PortD and that value is forced onto the corresponding I/O line. The PortD CMP2 and CMP3 read-only input bits indicate the results of the last analog comparisons (see

tor Inputs

for details on CMP2 and CMP3). PortD bit 5 is

PD2, PD3, PD4 Analog Compara-

always read as a 0. PortD is not affected by RESET.

76 5 432 1 0 0 0 CMPE 0 0 0 STE1 STE0

PORT D SPECIAL FUNCTION REGISTER (SFRD, LOCATION $08)

SFRD is an 8-bit wide register with 3 read/write control bits. The Strobe Enable 0 and 1-bits (STE0 and STE1) and used to conﬁgure PD0 and PD1 as strobed outputs. STE0 and STE1 only affect PD0 and PD1 when they are programmed as outputs by setting the corresponding bits in DDRD. See

PD0, PD1 Strobed Outputs

for a detailed explanation. The Comparator Enable bit (CMPE) controls the HIP7030A2’s auto-zeroing, analog comparator (see

log Comparator Inputs

for details on CMPE). SFRD bits 2, 3,

PD2, PD3, PD4 Ana-

4, 6 and 7 are always read as a 0. SFRD bit CMPE, is cleared by RESET. All other SFRD bits

are unaffected by RESET.

PD0, PD1 Strobed Output Mode

(DD0/DD1) is set, setting the STE0/1-bit conﬁgures the PD0/1 output in strobed mode. Clearing the STE0/1-bit causes the PD0/1 output to function identically to a PortA line in output mode. If the DDRD direction bit is clear, the associated line functions as an input and the state of the STE bit has no effect. When programmed as strobed outputs, data written to Port D Data Register bits 0 and 1 will appear on the external PD0 and PD1 pins synchronously with a low to high transition on the TCAP pin. This same transition on TCAP can be programmed to generate an interrupt to the processor. See

Programmable Timer

for details on using the interrupt capabilities of the TCAP pin. The strobed output mode of PD0 and PD1, coupled with the interrupt capability of TCAP, provides a mechanism for synchronously passing two bits of data between the HIP7030A2 and an external, asynchronous device.

SFRD

STE0/1

DAT A

DIR REG

BIT

LATCHED

OUTPUT

DATA BIT

TCAP

INTERNAL CONNECTIONS

INPUT REG BIT

FIGURE 6. STROBED OUTPUT BLOCK DIAGRAM (PD0, PD)

STROBE ENABLE

OUTPUT ENABLE

STROBED

OUTPUT

FLIP-FLOP

OUTPUT

A/B

MUX

INPUT I/O

I/O PIN

STE0 and STE1 are not affected by RESET.

TABLE 2. PORT D STROBED OUTPUTS TRUTH TABLE

(NOTE 1)

R/W DDR STE I/O PIN FUNCTION

W 0 X The I/O pin is in input mode.

Data is written into the output data latch.

W 1 0 Data is written into the output data latch

and simultaneously output to the I/O pin.

W 1 1 Data is written into the output data latch

and transferred to the I/O pin on the

next TCAP low to high transition. R 0 X The state of the I/O pin is read. R 1 0 The I/O pin is in standard output mode.

The output data latch is read. R 1 1 The I/O pin is in strobed output mode.

The output data latch is read.

NOTE:

1. R/W is an internal signal which equals R when reading the Port Data Register and equals W when writing the Port Data Register.

Page 13

HIP7030A2

PD2, PD3, PD4 Analog Comparator Input Mode

When the CMPE bit is low in SFRD PD2, PD3, and PD4 behave as standard bidirectional I/O pins. Each of these three pins can be programmed as an input pin by setting the associated DDR bit low. Setting the DDR bit high conﬁgures the pin as an output. When CMPE is set high the three pins are connected to the appropriate comparator inputs and the contents of the DDRD doesn’t affect comparator operation. While it is possible to perform comparisons of the pins when they are in the output mode (DDR bits are set high) the comparator result of comparing two equal digital values is not predictable. The comparator is intended for comparing analog input values, in which case the DDR bits must be set low to conﬁgure the pins as inputs. When CMPE is high, all of the associated PortD digital inputs (bits D4, D3, and D2 of PortD) are forced to 0, to conserve power.

DATA BIT

DRR BIT

DATA BIT

DRR BIT

INTERNAL LOGIC

V2/V3

1. Auto Zero

2. Compare V2, write results to CMP2

3. Auto Zero

4. Compare V3, write results to CMP3

The hardware sequencer is enabled via the CMPE bit. Once enabled the compare cycling is performed continuously at a 1MHz step rate until CMPE is set low. A complete cycle takes 4µs. It follows that, at any given time, the results read in CMP2 or CMP3 of the PortD Data Register can be, at most, 4µs old.

The auto-zero operation involves charging a pair of bias capacitors. The charging time depends on the source impedance of the analog inputs, the relative voltages of V2 and V3, and the slew rate of all three input voltages. Incomplete charging of the capacitors will affect the accuracy of the comparator. The comparator is intended to perform favor ab ly with input impedances up to 10kΩ and moderate slew rates.

J1850 Bus Interface

The VPW Symbol Encoder/Decoder (SENDEC) block provides the design with all the features needed to send and receive properly timed messages on a J1850 Class B Multiplexed Bus. Refer to

DEC)

for detailed documentation on the use of the SENDEC.

VPW Symbol Encoder/Decoder (SEN-

16-Bit Timer

The integrated 16-bit Timer includes both capture and compare features. External events can be timed, pulses generated, and periodic interrupts programmed. A sophisticated set of control and status registers allows interrupt or polled operation. For a detailed guide to the operation of the Timer refer to

Programmable Timer

FIGURE 7. ANALOG INPUT I/O PINS

The circuitry of the clocked comparator consists of a differential ampliﬁer with requisite current sources, auto-zero storage elements, and multiplexing switches. It is convenient to view it as a conventional differential comparator to which PD4 is connected as a “reference” at the negative input and PD2 and PD3 are connected via a multiplexer at the positive input. The comparator is enabled be setting the CMPE bit (bit 5) of SFRD and disabled by clearing CMPE. To conserve power the comparator should be disabled when not in use. RESET clears the CMPE bit. The three analog inputs function properly with inputs from -0.3V to V

+0.3V.

In order to use the comparator, PD4 and either (or both) PD2 or(and) PD3 should be selected as inputs via the DD2, DD3, and DD4 bits in DDRD. The results of the last comparison are available each time the PortD register is read. The CMP2 bit of PortD is set if PD2 was greater than PD4 during the last comparison and cleared otherwise. Similarly, the CMP3 bit of PortD is set if PD3 was greater than PD4 during the last comparison and cleared otherwise. CMP2 and CMP3 are not affected by RESET.

The HIP7030A2 includes a hardware sequencer to control the auto-zero function and input multiplexer of the comparator. Each complete compare cycle consists of a series of:

Serial Peripheral Interface (SPI)

The serial peripheral interface (SPI) is a synchronous serial interface with separate input, output, and clock lines. The SPI uses the MISO (serial data input/output), MOSI (serial data output/input), SCK (serial clock), and SS (slave select) pins. Refer to

Serial Peripheral Interface

for a detailed dis-

cussion of the SPI system.

Memory Organization

The HIP7030A2 MCU is capable of addressing 8192 bytes of memory and I/O registers with its program counter. The MCU has implemented 2520 bytes of these locations as shown in Figure 8. The ﬁrst 256 bytes of memory (page zero) include: 24 bytes of I/O features such as data ports, the port DDRs, Timer, serial peripheral interface (SPI), and J1850 VPW Registers; 48 bytes of user ROM, and 176 bytes of RAM. The next 2048 bytes complete the user ROM. The Built-In-Test ROM (228 bytes) and Built-In-Test vectors (14 bytes) are contained in memory locations $1F00 through $1FF1. The 14 highest address bytes contain the user deﬁned reset and the interrupt vectors. Eight bytes of the lowest 32 memory locations are unused and the 176 bytes of user RAM include up to 64 bytes for the stack. Since most programs use only a small part of the allocated stack locations for interrupts and/or subroutine stacking purposes, the unused bytes are usable for program data storage.

Page 14

HIP7030A2

CPU Registers

The CPU contains ﬁve registers, as shown in the programming model of Figure 9. The interrupt stacking order is shown in Figure 10.

Accumulator (A)

The accumulator is an 8-bit general purpose register used to hold operands, results of the arithmetic calculations, and data manipulations.

Index Register (X)

The X register is an 8-bit register which is used during the indexed modes of addressing. It provides an 8-bit value which is used to create an effective address. The index register is also used for data manipulations with the read-modify-write type of instructions and as a temporary storage register when not performing addressing operations.

Program Counter (PC)

The program counter is a 13-bit register that contains the address of the next instruction to be executed b y the processor .

Stack Pointer (SP)

The stack pointer is a 13-bit register containing the address of the next free locations on the pushdown/popup stack. When accessing memory, the most signiﬁcant bits are permanently conﬁgured to 0000011. These bits are appended to the six least signiﬁcant register bits to produce an address within the range of $00FF to $00C0. The stack area of RAM is used to store the return address on subroutine calls and the machine state during interrupts. During external or power-on reset, and during a reset stack pointer (RSP) instruction, the stack pointer is set to its upper limit ($00FF). Nested interrupt and/or subroutines may use up to 64 (decimal) locations. When the 64 locations are exceeded, the stack pointer wraps around and points to its upper limit ($00FF), thus, losing the previously stored information. A subroutine call occupies two RAM bytes on the stack, while an interrupt uses ﬁve RAM bytes.

Since the Stack Pointer decrements during pushes, the PCL is stacked ﬁrst, followed by PCH, etc. Pulling from the stack is in the reverse order.

Condition Code Register (CC)

The condition code register is a 5-bit register which indicates the results of the instruction just executed as well as the state of the processor. These bits can be individually tested by a program and speciﬁed action taken as a result of their state. Each bit is explained in the following paragraphs.

Half Carry Bit (H)

The H bit is set to a one when a carry occurs between bits 3 and 4 of the ALU during an ADD or ADC instruction. The H bit is useful in binary coded decimal subroutines.

Interrupt Mask Bit (I)

When the I-bit is set, all interrupts are disabled. Clearing this bit enables the interrupts. If an external interrupt occurs while the I-bit is set, the interrupt is latched and processed

after the I-bit is next cleared; therefore, no interrupts are lost because of the I-bit being set. An internal interrupt can be lost if it is cleared while the I-bit is set (refer to Programmable Timer, Serial Communications Interface, and Serial Peripheral Interface Sections for more information).

Negative (N)

When set, this bit indicates that the result of the last arithmetic, logical, or data manipulation is negative (bit 7 in the result is a logic one).

Zero (Z)

When set, this bit indicates that the result of the last arithmetic, logical, or data manipulation is zero.

Carry/Borrow (C)

Indicates that a carry or borrow out of the arithmetic logic unit (ALU) occurred during the last arithmetic operation. This bit is also affected during bit test and branch instructions, shifts, and rotates.

Built-In-Test (BIT)

The BIT test routines utilize the SPI interface of the HIP7030A2 to provide an efﬁcient method to test devices, both at the component and board level. The BIT routines are invoked by resetting the HIP7030A2 while applying 9V (through a 4.7kΩ resistor) to the IRQ pin and 5VDC to the TCAP pin. After reset, the HIP7030A2 will begin executing the BIT code stored at locations $1F00-$1FF1. The COP system remains active during BIT. When the BIT program begins, the SPI is conﬁgured in the master mode. SPI transfers are therefore controlled by the HIP7030A2. The tester paces the transfers by driving the SPI transfer. When the transfer is complete, the tester raises IRQ (to 5-9VDC) to signal successful transfer and to prepare for the next transfer. A convenient means of driving the pin is to connect it to 9V drive it with an open-collector/collector device such as the collector of an NPN device with its emitter grounded.

Following reset, the HIP7030A2 waits for a command to be received from the tester by monitoring the SPIF ﬂag in the SSR. throughout the BIT procedure. If the BIT routine will immediately branch to location $5D and begin executing the program stored there.

There are ﬁve BIT functions which are accessible via the SPI. Each is selected by sending the associated command number to the HIP7030A2. Following completion of each command (except Command $00), the HIP7030A2 waits for another command. Commands outside of the range $00-$04 will be ignored.

Download (Command $00):

Download takes 175 bytes from the SPDR and writes them to RAM beginning at $50 and ending and $FE. After receiving the 175th byte, the program begins executing at location $5D. The 13 locations $50-$5C are used as a link table to

through a 4.7kΩ resistor and to

SS should normally be held high

IRQ line low to initiate a

IRQ line and the

SS is low following reset,

IRQ

Page 15

HIP7030A2

allow testing of the interrupt functions. The link locations are: SPI Interrupt $50-51; Timer Interrupt $52-53; IRQ Interrupt $54-55; SED Interrupt $56-57; COP Interrupt $58-59; SWI Interrupt $5A-5C. If any entries in the link table are not required for the downloaded program, they may be used for variables or subroutines. Interrupts are disabled when exe-

$0000 0000 0000

$001f

$0020

$004F

$0050

$00BF $00C0

$00FF

$0100

$08FF

$0900

$1EFF

$1F00

$1FE1 $1FE2

$1FF1 $1FF2

$1FFF

I/O

32 BYTES

USER

ROM

48 BYTES

RAM

176 BYTES

STACK

64 BYTES

USER

ROM

2048 BYTES

UNUSED

5632 BYTES

BUILT-IN-TEST

VECTORS

USER VECTORS 14 BYTES

0031 0032

0079 0080

0191 0192

0255 0256

2303 2304

7935 7936

8177 8178

8191

256 BYTES

PORTS 1 BYTE

UNUSED 2 BYTES

PORTS

2 BYTES UNUSED

2 BYTES

PORTS

2 BYTES UNUSED

1 BYTE

SERIAL PERIPHERAL

INTERFACE

3 BYTES UNUSED

2 BYTES

SENDEC INTERFACE

3 BYTES

TIMER

10 BYTES

UNUSED

1 BYTE

WATCHDOG

2 BYTES UNUSED

1 BYTE

cution begins. If interrupts are enabled via a CLI instruction, handling of all interrupts which are generated (including the NEW interrupt) is required.

Location $5D is always the start location.

0031

PORT A DATA REGISTER

UNUSED UNUSED

PORT D DATA REGISTER

PORT A DATA DIRECTION REGISTER

UNUSED UNUSED

PORT D DATA DIRECTION REGISTER

PORT D SPECIAL FUNCTION REGISTER

UNUSED

SERIAL PERIPHERAL CONTROL REGISTER

SERIAL PERIPHERAL STATUS REGISTER

SERIAL PERIPHERAL DATA I/O REGISTER

UNUSED UNUSED

SENDEC CONTROL REGISTER

SENDEC STATUS REGISTER

SENDEC DATA REGISTER

TIMER CONTROL REGISTER

TIMER STATUS REGISTER

INPUT CAPTURE HIGH REGISTER

INPUT CAPTURE LOW REGISTER

OUTPUT COMPARE HIGH REGISTER

OUTPUT COMPARE LOW REGISTER

COUNTER HIGH REGISTER

COUNTER LOW REGISTER ALTERNATE COUNTER HIGH REGISTER ALTERNATE COUNTER LOW REGISTER

UNUSED

WATCHDOG RESET REGISTER

WATCHDOG STATUS REGISTER

UNUSED

$00 $01 $02 $03 $04 $05 $06 $07 $08 $09 $0A $0B $0C $0D $0E $0F $10 $11 $12 $13 $14 $15 $16 $17 $18 $19 $1A $1B $1C $1D $1E $1F

FIGURE 8. MEMORY MAP OF THE HIP7030A2

Page 16

HIP7030A2

1100000

FIGURE 9. CPU REGISTER SET

RETURN

000

PROGRAM COUNTER LOW

INCREASING

MEMORY

ADDRESS

FIGURE 10. STACKING ORDER DURING INTERRUPTS

CONDITION CODE REG

ACCUMULATOR (A)

INDEX REGISTER (X)

PROGRAM COUNTER HIGH

ACCUMULATOR

INDEX REGISTER

012

PROGRAM COUNTER

012

STACK POINTER

CZNIH

CONDITION CODE REG

CARRY/BORROW ZERO NEGATIVE INTERRUPT MASK HALF CARRY

DECREASING

MEMORY

ADDRESS

INTERRUPT

return data is a three character ASCII sequence which uniquely identiﬁes each customer’s mask ROM pattern.

Resets

The MCU has three reset modes: an active low external reset pin ( puter Operating Properly (COP) reset function.

RESET Pin

The orderly software start-up procedure. When using the external reset mode, the of one and one half t nal Schmitt Trigger as part of its input to improve noise immunity.

Power-On Reset

The power-on reset occurs when a positive transition is detected on V power turn-on conditions and should not be used to detect any drops in the power supply voltage. There is no provision for a power-down reset. The po wer-on circuitry provides f or a 4064 t active to allow for stabilization (see Figure 11). If the external RESET pin is low at the end of the 4064 t processor remains in the reset condition until high. Table 3 shows the actions of the two resets on internal circuits, but not necessarily in order of occurrence (X indicates that the condition occurs for the particular reset).

RESET), a power-on reset function, and a Com-

RESET input pin is used to reset the MCU to provide an

RESET pin must stay low for a minimum

. The RESET pin contains an inter-

CYC

. The power-on reset is used strictly for

delay from the time that the oscillator becomes

CYC

time out, the

CYC

RESET goes

ROM Dump (Command $01):

ROM Dump reads the entire ROM contents and transfers them one byte at a time via the SPI register. The entire ROM must be read from start to end. Locations $20-$4F, $100$8FF, and $1F00-$1FFF are read in lowest to highest address sequence. Following the complete ROM contents, a two byte checksum is transferred.

Read Page 0 (Command $02):

Allows reading of any page 0 byte (i.e., $00-$FF). The command ($02) is sent, followed by the address, followed by the data transfer. The data sent is ignored, while the return data is the contents of the speciﬁed address. The three byte sequence must be repeated for each transfer.

Write Page 0 (Command $03):

Allows writing of any non-ROM, P age 0 b yte (i.e., $00-$1F or $50-$FF). The command ($03) is sent, followed by the address, followed by the data transfer. The data is written to the location, while the return data is the contents of the speciﬁed address. The three byte sequence must be repeated for each transfer. The procedure will work for ROM locations identically to all other locations, except the write will be supressed.

Read Mask ID (Command $04):

Transfers the three character custom mask ID assigned to each customer pattern. The command ($04) is sent, followed by three data transfers The data sent is ignored, while the

COP Reset

The COP reset is generated by either of two events: 1) the Watchdog Timer reaches its maximum value prior to being cleared, or 2) the Slow Clock Detect circuitry doesn’t detect a transition on the OSCIN pin during a period of approximately 2µs. The COP reset is identical to an external RESET pin reset, except the Program Counter is loaded with the address at $1FFA-$1FFB instead of the address at $1FFE-$1FFF and the Watchdog Flag (bit 0) is set in the Watchdog Status Register (WSR, location $1E). COP Resets are discussed under Interrupts.

Interrupts

Systems often require that normal processing be interrupted so that some external event may be serviced. The HIP7030A2 may be interrupted by one of six different methods: either one of four maskable hardware interrupts ( SPI, SENDEC, or Timer), one non-maskable Watchdog/Slow Clock Detect interrupt, and one non-maskable software interrupt (SWI). Interrupts such as Timer, SPI, and SENDEC have several ﬂags which will cause the interrupt. Generally, interrupt ﬂags are located in read-only status register, whereas, their equivalent enable bits are located in associated control registers. The interrupt ﬂags and enable bits are never contained in the same register. If the enable bit is a logic zero it blocks the interrupt from occurring but does not inhibit the ﬂag from being set. Reset clears all enable bits to preclude interrupts during the reset procedure.

IRQ,

Page 17

HIP7030A2

The general sequence for clearing an interrupt is a software sequence of ﬁrst accessing the status register while the interrupt ﬂag is set, followed by a read or write of an associated register. When any of these interrupts occur, and if the enable bit is a logic one, normal processing is suspended at the end of the current instruction execution. Interrupts cause the processor registers to be saved on the stack (see Figure

12) and the interrupt mask (I-bit) set to prevent additional interrupts. The appropriate interrupt vector then points to the starting address of the interrupt service routine (refer to Table 4 for vector location). Upon completion of the interrupt service routine, the RTI instruction (which is normally a part of the service routine) causes the register contents to be

Hardware Controlled Interrupt Sequence

The following three functions (RESET, STOP, and WAIT) are not in the strictest sense an interrupt; however, they are acted upon in a similar manner. Flowcharts for hardware interrupts are shown in Figure 13, and for STOP and WAIT are provided in Figure 14. A discussion is provided below.

(a) RESET - A low input on the

RESET input pin causes the program to vector to its starting address which is speciﬁed by the contents of memory locations $1FFE and $1FFF. The I bit in the condition code register is also set. Much of the MCU is conﬁgured to a known state during this type of reset as previously described in RESETS paragraph.

recovered from the stack followed by a return to normal processing. The stack order is shown in Figure 12.

NOTE: The interrupt mask bit (I-bit) will be cleared if and only if the corresponding bit stored in the stack is zero. A discussion of interrupts, plus a table listing vector addresses for all interrupts including RESET, in the MCU is provided in Table 4.

TABLE 3. RESET PIN, COP, AND POR ACTIONS ON INTERNAL CIRCUITRY

RESET PIN/

CONDITION

Timer Prescaler Reset to Zero State X X Timer Counter Configure to $FFFC X X Timer Output Compare (TCMP) Bit Reset to Zero X X All Timer Interrupt Enable Bits Cleared (ICIE, OCIE, and TOIE) to Disable Timer Interrupts X X Timer Output Level (OLVL) Bit is Cleared X X Port A and Port D Data Direction Registers (DDRA and DDRD) Cleared to Zero, Placing

all Port Pins in Input Mode Port D Special Function Register Bit CMPE is Cleared Disabling Comparator X X Set Stack Pointer (SP) to $00FF X X Force Internal Address to RESET Vector ($1FFE) X X Set I-Bit in Condition Code Register (CC) to 1; Disabling all Maskable Interrupts X X Clear STOP Latch XX Clear WAIT Latch XX Reset Oscillator Stabilization Delay to 4064 (Note 1) X Clear External Interrupt (Irq) Flip-flop X X VPWOUT Set Low (Passive State) X X Slow Clock Detect Circuitry Reset (Note 1) X Watchdog Timer Reset to Zero State X X Watchdog Flag (WDF) Cleared/Set in Watchdog Status Register (WSR) (Note 2) (Note 2) Watchdog Timer Interrupt Latch Cleared X X Serial Peripheral Interface (SPI) Control Bits SPIE, MSTR, SPIF, WCOL, and MODF

Cleared; Disabling SPI Interrupts and Setting to Slave Mode

NOTES:

1. Only if MCU is in STOP state; if NDEL is set in the SENDEC Control Register a delay of 128 is used for RESET/COP.

2. WDF is cleared by POR and is set by a Watchdog Reset. RESET has no effect on WDF.

COP RESET

POWER-ON

RESET

Page 18

OSCIN

(NOTE 2)

INTERNAL

PROCESSOR

CLOCK (NOTE 1)

OXOV

4064

CYC

HIP7030A2

INTERNAL

ADDRESS BUS

(NOTE 1)

INTERNAL

DATA BUS

(NOTE 3)

RESET

1FFE

NEW PCH

1FFF

NEW

PCL

NEW

CODE

1FFE 1FFE 1FFE 1FFE 1FFF

PCH PCL

(NOTE 3)

NOTES:

1. Internal signal and bus information is not available externally.

2. OSCIN is not meant to represent frequency. It is only meant to represent time.

3. The next rising edge of the internal processor clock following the rising edge of RESET initiates the reset sequence.

FIGURE 11. POWER-ON RESET AND RESET

TABLE 4. VECTOR ADDRESSES FOR INTERRUPTS AND RESETS

N/A N/A RESET RESET $1FFE-$1FFF N/A N/A Software SWI $1FFC-$1FFD N/A N/A Watchdog Timeout COP $1FFA-$1FFB

NEW

CODE

Slow Clock Detect

SENDEC Status

TX Transition Detected SENDEC $1FF8-$1FF9

(SEDSR)

BRK Break Detected

NEW IFS or SOF

NECHO Echo Failure

N/A N/A External Interrupt IRQ $1FF6-$1FF7

TIMER Status

ICF Input Capture TIMER $1FF4-$1FF5

(TSR)

OCF Output Compare TOF Timer Overflow

SPI Status

SPIF Transfer Complete SPI $1FF2-$1FF3

(SPSR)

MODF Mode Fault

Page 19

HIP7030A2

IRQ

FROMRESET

COP

INTERNAL

INTERRUPT

I BIT (CC)

FIGURE 12A. INTERRUPT FUNCTION DIAGRAM

ILIH

ILIL

FIGURE 12B. INTERRUPT TIMING DIAGRAM

FIGURE 12. EXTERNAL INTERRUPT

TO COP RESET

EXTERNAL INTERRUPT REQUEST

POWER-ON RESET EXTERNAL RESET

COP RESET EXTERNAL

INTERRUPT BEING SERVICED (READ OF VECTORS)

IS I

IBIT

SET?

SENDEC

INTERNAL

INTERRUPT

IRQ

EXTERNAL

INTERRUPT

TIMER

INTERNAL

INTERRUPT

SPI

INTERNAL

INTERRUPT

FETCH

INSTRUCTION

IRQ

CLEAR

EDGE TRIGGERED

FLIP-FLOP

STACK

PC, X, A, CC

SET I BIT

LOAD PC FROM

SENDEC:$1FF8- $1FF9

IRQ: $1FF6 - $1FF7

TIMER:$1FF4- $1FF5

SPI: $1FF2 - $1FF3

COMPLETE

INTERRUPT

ROUTINE

AND EXECUTE

RTI

EXECUTE

INSTRUCTION

FIGURE 13. HARDWARE INTERRUPT FLOW DIAGRAM

Page 20

HIP7030A2

(b) STOP - The STOP instruction causes the oscillator to be turned off and the processor to “sleep” until an external interrupt (IRQ) or reset occurs. The VPWOUT pin is forced to a low level, the SPI is set to slave mode, and all other pins remain at their previously set levels.

(c) WAIT - The WAIT instruction causes all processor clocks to stop, but leaves the Timer, the Watchdog, SENDEC, and SPI clocks running. This “rest” state of the processor can be cleared by RESET, Slow Clock Detect, an external interrupt (IRQ), Timer interrupt, SPI interrupt, or SENDEC interrupt. There are no special “wait mode” vectors for these interrupts.

Software Interrupt (SWI)

The software interrupt is an executable instruction. The action of the SWI instruction is similar to the hardware interrupts. The SWI is executed regardless of the state of the interrupt mask (I-bit) in the condition code register. The interrupt service routine address is speciﬁed by the contents of memory location $1FFC and $1FFD.

COP Interrupt/Reset

The Computer Operating Properly (COP) system consists of two functions: 1) the Watchdog Timer, and 2) the Slow Clock Detect Circuit. These interrupts cause a complete system restart and the effect is identical in every respect to an externally generated is taken from locations $1FFA and $1FFB and the Watchdog Flag (bit-0) is set in the Watchdog Status Register (WSR, location $1E) if the reset was the result of a Watchdog Timer overﬂow. Starting the PC with an address different than the standard RESET address allows the system to provide an appropriate response to the situation.

Because the CPU is reset during a COP Interrupt, the COP service routine must not exit with an RTI. Instead the routine should branch to subsequent code.

Since the most likely cause of a Slow Clock Detect is a malfunctioning oscillator, a COP Interrupt caused by a Slow Clock Detect will generally reset the MCU per Table 3 and remain in the RESET state.

SENDEC Interrupt

The VPW Symbol Encoder/Decoder (SENDEC) system has four different interrupt ﬂags that will cause a SENDEC interrupt whenever they are set and enab led. These four interrupt ﬂags are found in the SENDEC status register (SEDSR, location $10) and all will vector to the same interrupt service routine ($1FF8-$1FF9). One of the interrupt ﬂags (TX - transition) has a corresponding enable bit in the SENDEC control register (SEDCR, location $0F). RESET clears the enable bit, thus, preventing a TX interrupt from occurring during the reset time period. The other three interrupts (BRK

- break, NECHO - no echo, and NEW - new frame) are nonmaskable at the SENDEC level. The processor responds to all SENDEC interrupts only if the I-bit in the condition code register is also cleared. When the interrupt is recognized, the current machine state is pushed onto the stack and I bit is set. This masks further interrupts until the present one is serviced. The interrupt ser vice routine address is speciﬁed

RESET pin reset, except the restart address

by the contents of memory location $1FF8 and $1FF9. The general sequence for clearing an interrupt is a software sequence of accessing the status register while the ﬂag is set, followed by a read or write of an associated register. Refer to VPW Symbol Encoder/Decoder (SENDEC) for additional information about the SENDEC interrupts.

External Interrupt

If the interrupt mask (I bit) of the condition code register has been cleared and the external interrupt pin ( low, then an external interrupt is recognized. When the interrupt is recognized, the current state of the CPU is pushed onto the stack and the I bit is set. This masks further interrupts until the present one is serviced. The interrupt ser vice routine address is speciﬁed by the contents of memory location $1FF6 and $1FF7. Figure 12 shows both a functional and mode timing diagram for the interrupt line. The timing diagram shows treatment of the interrupt line (IRQ) for generating periodic interrupts to the processor. The ﬁgure shows single pulses on the interrupt line spaced far enough apart to be serviced. The minimum time between pulses is a function of the number of cycles required to execute the interrupt service routine plus 21 cycles (for interrupt call and return delays). Once a pulse occurs, the next pulse should not occur until the MCU software has exited the routine (an RTI occurs).

The internal interrupt latch is cleared in the ﬁrst part of the service routine; therefore, one (and only one) external interrupt pulse can be latched during t soon as the I bit is cleared.

Timer Interrupt

There are three different timer interrupt ﬂags that will cause a timer interrupt whenever they are set and enabled. These three interrupt ﬂags are found in the three most signiﬁcant bits of the timer status register (TSR, location $13) and all three will vector to the same interrupt service routine ($1FF4-$1FF5). All interrupt ﬂags have corresponding enable bits (ICIE, OCIE, and TOIE) in the timer control register (TCR, location $12). Reset clears all enable bits, thus, preventing an interrupt from occurring during the reset time per iod. The actual processor interrupt is generated only if the I-bit in the condition code register is also cleared. When the interrupt is recognized, the current machine state is pushed onto the stack and I-bit is set. This masks further interrupts until the present one is serviced. The interrupt ser vice routine address is speciﬁed by the contents of memory location $1FF4 and $1FF5. The general sequence for clearing an interrupt is a software sequence of accessing the status register while the ﬂag is set, followed by a read or write of an associated register. Refer to Programmable Timer for additional information about the timer circuitry.

Serial Peripheral Interface (SPI) Interrupts

An interrupt in the serial peripheral interface (SPI) occurs when one of the interrupt ﬂag bits in the serial peripheral status register (location $0B) is set, provided the I-bit in the condition code register is clear and the enable bit in the serial peripheral control register (location $0A) is enabled. When the interrupt is recognized, the current state of the machine

and will be serviced as

ILIL

IRQ) has gone

Page 21

HIP7030A2

is pushed onto the stack and the I bit in the condition code register is set. This masks further interrupts until the present one is serviced. The SPI interrupt causes the program counter to vector to memory location $1FF2 and $1FF3 which contain the starting address of the interrupt ser vice routine. Software in the serial peripheral interrupt service routine must determine the priority and cause of the SPI interrupt by examining the interrupt ﬂag bits located in the SPI status register. The general sequence for clearing an interrupt is a software sequence of accessing the status register while the ﬂag is set, followed by a read or write of an associated register. Refer to Serial Peripheral Interface for a description of the SPI system and its interrupts.

Low Power Modes

STOP Instruction

The STOP instruction places the MCU in its lowest power consumption mode. In the STOP mode the internal oscillator is turned off, causing all internal processing to be halted; refer to Figure 14. During the STOP mode, the I-bit in the condition code register is automatically cleared to enable external and SENDEC interrupts. All other registers and memory remain unaltered and all input/output lines remain unchanged, except the VPWOUT line which is forced to a

passive (low) state and the SPI Master bit (MSTR) in the SPI Control Register (SPCR) which is cleared placing the SPI pins into Slave mode. This mode persists until an external interrupt (IRQ), a low on the

VPWIN pin, or a low on RESET is sensed, at which time the internal oscillator is tur ned on. The interrupt or reset causes the program counter to vector to the starting address of the interrupt or reset ser vice routine respectively.

WAIT Instruction

The WAIT instruction places the MCU in a low power consumption mode, but the WAIT mode consumes somewhat more power than the STOP mode. In the WAIT mode, the internal clock remains active, and all CPU processing is stopped; however, the programmable timer, serial peripheral interface, Watchdog Timer, and SENDEC systems remain active. Refer to Figure 14. During the WAIT mode, the I-bit in the condition code register is cleared to enable all interrupts. All other registers and memory remain unaltered and all parallel input/output lines remain unchanged. This continues until any interrupt or reset is sensed. At this time the program counter vectors to the memory location ($1FF2 through $1FFF) which contains the starting address of the interrupt or reset service routine.

EXTERNAL

INTERRUPT

IRQ

YES

STOP

STOP OSCILLATOR AND CLOCKS, DISABLE COP,

FORCE VPWOUT = 0,

CLEAR I-BIT

SENDEC

INTERRUPT

YES

(1) FETCH RESET/COP VECTOR OR (2) SERVICE INTERRUPT

A. STACK B. SET I-BIT C. VECTOR TO INTERRUPT

ROUTINE

RESET

YES

TURN ON OSCILLATOR

WAIT FOR TIME

DELAY TO STABILIZE

WAIT

OSCILLATOR ACTIVE,

TIMER, SENDEC, AND SPI

CLOCKS ACTIVE, CLEAR I-BIT,

PROCESSOR CLOCKS STOPPED

RESET

YES

RESET

PROCESSOR

RESTART

PROCESSOR CLOCK

(1) FETCH RESET/COP VECTOR OR (2) SERVICE INTERRUPT

A. STACK B. SET I-BIT C. VECTOR TO INTERRUPT

ROUTINE

COP

INTERRUPT

YES

SENDEC

INTERRUPT

IRQ

INTERRUPT

TIMER

INTERRUPT

SPI

INTERRUPT

FIGURE 14. STOP AND WAIT FLOW DIAGRAM

Page 22

HIP7030A2

Data Retention Mode

The contents of RAM and CPU registers are retained at supply voltages as low as 2V

. This is referred to as the DATA

RETENTION mode, where the data is held, but the device is not guaranteed to operate.

Programmable Timer

Introduction

The programmable timer, which is preceded by a ﬁxed divide-by-four prescaler, can be used for many purposes, including input waveform measurements while simulta-

MCU INTERNAL BUS

INTERNAL

PROCESSOR

CLOCK

HIGH

$16 $17

BYTE

LOW

BYTE

OUTPUT COMPARE REGISTER

÷4

HIGH BYTE

16-BIT FREE

RUNNING

COUNTER COUNTER

ALTERNATE

neously generating an output waveform. Pulse widths can vary from several microseconds to many seconds. A block diagram of the timer is shown in Figure 15 and timing diagrams are shown in Figure 16 through 19. Because the timer has a 16-bit architecture, each speciﬁc functional segment (capability) is represented by two registers. These registers contain the high and low byte of that functional segment. Generally, accessing the low byte of a speciﬁc timer function allows full control of that function; however, an access of the high byte inhibits that speciﬁc timer function until the low byte is also accessed.

8-BIT-

BUFFER

HIGH

LOW

BYTE

$18 $19

$1A $1B

BYTE

LOW

BYTE

INPUT CAPTURE REGISTER

$14 $15

TIMER

STATUS

REG.

$13

OVERFLOW

DETECT CIRCUIT

TOIE IEDG OLVLICIE OCIE

OUTPUT

LEVEL REG.

TIMER

CONTROL

REG.

$12

EDGE DETECT CIRCUIT

CLK

RESET

OUTPUT

COMPARE

CIRCUIT

INTERRUPT

CIRCUIT

TOFICF OCF

FIGURE 15. PROGRAMMABLE TIMER BLOCK DIAGRAM

OUTPUT

LEVEL (TCMP

PIN 2)

EDGE INPUT (TCAP PIN 1)

Page 23

INTERNAL PROCESSOR CLOCK

(INTERNAL RESET)

HIP7030A2

T00

INTERNAL TIMER CLOCKS

COUNTER (16-BIT)

RESET (EXTERNAL OR END OF POR)

T01

T10

T11

$FFFC

$FFFD $FFFE $FFFF

NOTE:

1. The Counter Register and the Timer Control Register are the only ones affected by reset.

FIGURE 16. TIMER STATE DIAGRAM FOR RESET

INTERNAL PROCESSOR

INTERNAL TIMER

CLOCKS

CLOCK

T00

T01

T10

T11

COUNTER (16-BIT)

INPUT EDGE

(SEE NOTE)

INTERNAL CAPTURE LATCH

INPUT CAPTURE REGISTER

INPUT CAPTURE FLAG

$FFEC$FFEB

$???? $FFED

$FFED $FFEE $FFEF

NOTE:

1. The Counter Register and the Timer Control Register are the only ones affected by reset.

FIGURE 17. TIMER STATE DIAGRAM FOR INPUT CAPTURE

Page 24

INTERNAL PROCESSOR CLOCK

T00

T01

INTERNAL TIMER

T10

T11

HIP7030A2

COUNTER (16-BIT)

COMPARE REGISTER

LATCH

OUTPUT COMPARE

FLAG (OCF) AND

TCMP (PIN 2)

$FFEC$FFEB

(NOTE 1)

CPU WRITES $FFED $FFED

(NOTE 2)

$FFED $FFEE $FFEF

(NOTE 3)

NOTES:

1. The CPU write to the Compare Register may take place at any time, b ut a compare only occurs at timer state T01. Thus , a 4 cycle difference may exist between the write to the Compare Register and the actual compare.

2. Internal compare takes place during timer state T01.

3. OCF is set at the timer state T11 which follows the comparison match ($FFED in this example).

FIGURE 18. TIMER STATE DIAGRAM FOR OUTPUT COMPARE

INTERNAL PROCESSOR CLOCK

T00

T01

INTERNAL TIMER

T10

T11

COUNTER (16-BIT)

TIMER OVERFLOW

FLAG (TOF)

$FFFF$FFFE

$0000 $0001 $0002

NOTE:

1. The TOF bit is set at timer state T11 (transition of the counter from $FFFF to $0000). It is cleared by a read of the Timer S tatus Register during the internal processor clock high time followed by a read of the Counter Low Register

FIGURE 19. TIMER STATE DIAGRAM FOR TIMER OVERFLOW

Page 25

HIP7030A2

The I-1bit in the condition code register should be set while manipulating both the high and low byte register of a speciﬁc timer function to ensure that an interrupt does not occur. This prevents interrupts from occurring between the time that the high and low bytes are accessed.

The programmable timer capabilities are provided by using the following ten addressable 8-bit registers (note the high and low represent the signiﬁcance of the byte). A description of each register is provided below.

Timer Control Register (TCR) locations $12, Timer Status Register (TSR) location $13, Input Capture High Register location $14, Input Capture Low Register location $15, Output Compare High Register location $16, Output Compare Low Register location $17, Counter High Register location $18, Counter Low Register location $19, Alternate Counter High Register location $1A, and Alternate Counter Low Register location $1B.

Counter

The key element in the programmable timer is a 16-bit free running counter, or counter register , preceded b y a prescaler which divides the internal processor clock by four. The prescaler gives the timer a resolution of 800ns if the internal processor clock is 5.0MHz. the counter is clocked to increasing values during the low portion of the internal processor clock. Software can read the counter at any time without affecting its value.

The double byte free running counter can be read from either of two locations $18 - $19 (called counter register at this location), or $1A - $1B (counter alternate register at this location). A read of only the least signiﬁcant byte (LSB) of the free running counter ($19, $1B) retrieves the current count value. If a read of the free running counter ﬁrst addresses the most signiﬁcant byte ($18, $1A) the least signiﬁcant byte is transferred to a buffer. This buffer value remains ﬁxed after the ﬁrst most signiﬁcant byte “read” even if the user reads the most signiﬁcant byte several times. This buffer is accessed when reading the LSB of the free running counter or counter alternate register ($19, $1B), if the most signiﬁcant byte is read, the least signiﬁcant byte must also be read in order to complete the sequence.

The free r unning counter is conﬁgured to $FFFC during reset and is always a read-only register. During a power-on-reset (POR) or a COP reset, the counter is also conﬁgured to $FFFC and begins running after the oscillator start-up delay. Because the free running counter is 16-bits preceded by a ﬁxed divideby-four prescaler, the value in the free running counter repeats every 262,144 MPU internal processor clock cycles. When the counter rolls over from $FFFF to $0000, the timer overﬂow ﬂag (TOF) bit is set. An interrupt can also be enabled when counter rollover occurs by setting its interrupt enable bit (TOIE).

Output Compare Register

The output compare register is a 16-bit register, which is made up of two 8-bit registers at locations $16 (most signiﬁcant byte) and $17 (least signiﬁcant byte). The output compare register can be used for several purposes such as, controlling an output wavef orm or indicating when a period of

time has elapsed. The output compare register is unique in that all bits are readable and writable and are not altered by the timer hardware. Reset does not affect the contents of this register and if the compare function is not utilized, the two bytes of the output compare register can be used as storage locations.

The contents of the output compare register are compared with the contents of the free running counter once during every four internal processor clocks. If a match is found, the corresponding output compare flag (OCF) bit is set and the corresponding output level (OLVL) bit is clocked (by the output compare circuit pulse) to an output level register. The values in the output compare register and the output level bit should be changed after each successful comparison in order to control an output waveform or establish a new elapsed timeout. An interrupt can also accompany a successful output compare provided the corresponding interrupt enable bit, OCIE, is set.

After a processor write cycle to the output compare register containing the most signiﬁcant byte ($16), the output compare function is inhibited until the least signiﬁcant byte ($17) is also written. The user must write both bytes (locations) if the most signiﬁcant byte is written ﬁrst. A write made only to the least signiﬁcant byte ($17) will not inhibit the compare function. The free running counter is updated every four internal processor clock cycles due to the internal prescaler. The minimum time required to update the output compare register is a function of the software program rather than the internal hardware.

A processor write may be made to either byte of the output compare register without affecting the other byte. The output level (OLVL) bit is clocked to the output level register regardless of whether the output compare ﬂag (OCF) is set or clear.

Because neither the output compare ﬂag (OCF bit) nor the output compare register is affected by RESET, care must be exercised when initializing the output compare function with software. The following procedure is recommended:

1. Write the high byte of the output compare register to inhibit further compares until the low byte is written.

2. Read the timer status register to arm the OCF if it is already set.

3. Write the output compare register low byte to enable the output compare function with the ﬂag clear.

The advantage of this procedure is to prevent the OCF bit from being set between the time it is read and the write to the output compare register. A software example is shown below.

B716 STA OCMPHI; INHIBIT OUTPUT COMPARE B613 LDA TSTAT; ARM OCF BIT IF SET BF17 STX OCMPLO; READY FOR NEXT COMPARE

Input Capture Register

The two 8-bit registers which make up the 16-bit input capture register are read-only and are used to latch the value of the free running counter after a deﬁned transition is sensed by the corresponding input capture edge detector. The level transition which triggers the counter transfer is deﬁned by the corresponding input edge bit (IEDG). The selected edge

Page 26

HIP7030A2

is also fed to the Port D strobed output pins (see Port D Strobed Output Mode). Reset does not affect the contents of the input capture register.

The result obtained by an input capture will be one more than the value of the free running counter on the rising edge of the internal processor clock preceding the external transition (refer to timing diagram shown in Figure 17). This delay is required for internal synchronization. Resolution is affected by the prescaler allowing the timer to only increment every four internal processor clock cycles.

After a read of the most signiﬁcant byte of the input capture register ($14), counter transfer is inhibited until the least signiﬁcant byte ($15) of the input capture register is also read. This characteristic forces the minimum pulse period attainable to be determined by the time used in the capture software routine and its interaction with the main program. The free running counter increments every four internal processor clock cycles due to the prescaler.

A read of the least signiﬁcant byte ($15) of the input capture register does not inhibit the free running counter transfer. Again, minimum pulse periods are ones which allow software to read the least signiﬁcant byte ($15) and perform needed operations. There is no conﬂict between the read of the input capture register and the free running counter transfer since they occur on opposite edges of the internal processor clock.

Timer Control Register (TCR)

The timer control register (TCR, location $12) is an 8-bit read/write register which contains ﬁve control bits. Three of these bits control interrupts associated with each of the three ﬂag bits found in the timer status register (discussed below). The other two bits control: 1) which edge is signiﬁcant to the capture edge detector (i.e., negative or positive), and 2) the next value to be clocked to the output level register in response to a successful output compare. The timer control register and the free running counter are the only sections of the timer affected by RESET. The TCMP pin is forced low during external reset and stays low until a valid compare changes it to a high. The timer control register is illustrated below followed by a deﬁnition of each bit.

76543210

ICIE OCIE TOIE 0 0 0 IEDG OLVL

TCR (LOCATION $12)

B7, ICIE If the input capture interrupt enable (ICIE) bit is

set, a timer interrupt is enabled when the ICF status ﬂag (in the timer status register) is set. If the ICIE bit is clear, the interrupt is inhibited. The ICIE bit is cleared by RESET.

B6, OCIE If the output compare interrupt enable (OCIE) bit

is set, a timer interrupt is enabled whenever the OCF status ﬂag is set. If the OCIE bit is clear, the interrupt is inhibited. The OCIE bit is cleared by RESET.

B5, TOIE If the timer overﬂow interrupt enable (TOIE) bit is

set, a timer interrupt is enabled whenever the TOF status ﬂag (in the timer status register) is set. If

the TOIE bit is clear, the interrupt is inhibited. The TOIE bit is cleared by RESET.

B1, IEDG The value of the input edge (IEDG) bit determines

which level transition on pin 1 will trigger a free running counter transfer to the input capture register. Reset does not affect the IEDG bit.

0 = negative edge 1 = positive edge

B0, OLVL The value of the output level (OLVL) bit is clocked

into the output level register by the next successful output compare and will appear at pin 2. This bit and the output level register are cleared by RESET.

0 = low output 1 = high output

Timer Status Register (TSR)

The timer status register (TSR) is an 8-bit register of which the three most signiﬁcant bits contain read-only status information. These three bits indicate the following:

1. A proper transition has taken place at the TCAP pin with an accompanying transfer of the free running counter contents to the input capture register,

2. A match has been found between the free running counter and the output compare register, and

3. A free running counter transition from $FFFF to $0000 has been sensed (timer overflow).

The timer status register is illustrated below followed by a deﬁnition of each bit. Refer to timing diagrams shown in Figures 13, 14, and 15 for timing relationship to the timer status register bits.

76543210

ICF OCF TOF 0 0 0 0 0

TSR (LOCATION $13)

B7, ICF The input capture ﬂag (ICF) is set when a proper

edge has been sensed by the input capture edge detector. It is cleared by a processor access of the timer status register (with ICF set) followed by accessing the low byte ($15) of the input capture register. Reset does not affect the input compare ﬂag.

B6, OCF The output compare ﬂag (OCF) is set when the

output compare register contents match the contents of the free running counter. The OCF is cleared by accessing the timer status register (with OCF set) and then accessing the low byte ($17) of the output compare register. Reset does not affect the output compare ﬂag.

B5, TOF The timer overﬂow ﬂag (TOF) bit is set by a transi-

tion of the free running counter from $FFFF to $0000. It is cleared by accessing the timer status register (with TOF set) followed by an access of the free running counter least signiﬁcant byte ($19). Reset does not affect the TOF bit.

Page 27

HIP7030A2

Accessing the timer status register satisﬁes the ﬁrst condition required to clear any status bits which happen to be set during the access. The only remaining step is to provide an access of the register which is associated with the status bit. Typically, this presents no problem for the input capture and output compare functions.

A problem can occur when using the timer overﬂow function and reading the free running counter at random times to measure an elapsed time. Without incorporating the proper precautions into software, the timer overﬂow ﬂag could unintentionally be cleared if: 1) the timer status register is read or written when TOF is set, and 2) the least signiﬁcant byte of the free running counter is read but not for the purpose of servicing the ﬂag. The counter alternate register at address $1A and $1B contains the same value as the free running counter (at address $18 and $19); therefore, this alternate register can be read at any time without affecting the timer overﬂow ﬂag in the timer status register.

During STOP and WAIT instructions, the programmable timer functions as follows: during the wait mode, the timer continues to operate normally and may generate an interrupt to trigger the CPU out of the wait state; during the stop mode, the timer holds at its current state, retaining all data, and resumes operation from this point when an external interrupt is received.

Serial Peripherial Interface (SPI) Introduction

The serial peripheral interface (SPI) is an interface built into the MCU which allows several MCUs, or one MCU plus peripheral devices, to be interconnected within a single “black box” or on the same printed circuit board. In a serial peripheral interface (SPI), separate wires (signals) are required for data and clock. In the SPI format, the clock is not included in the data stream and must be furnished as a separate signal. An SPI system may be conﬁgured as one containing one master MCU and several slave MCUs, or in a system in which an MCU is capable of being either a master or a slave .

Figure 20 illustrates a typical multi-computer system conﬁguration. Figure 20 represents a system of ﬁve different MCUs in which there are one master and four slave (0, 1, 2, 3). In this system four basic line (signals) are required for the MOSI (master out slave in), MISO (master in slav e out), SCK serial clock, and

Features

• Full Duplex, Three-wire Synchronous Transfers

• Master or Slave Operation

• Master Bit Frequency - 2.5MHz Maximum

• Slave Bit Frequency - 5.0MHz Maximum

• Four Programmable Master Bit Rates

• Programmable Clock Polarity And Phase

• End Of Transmission Interrupt Flag

• Write Collision Flag Protection

• Master-master Mode Fault Protection Capability

SS (slave select) lines.

HIP7030A2

MASTER

Signal Description

The four basic signals (MOSI, MISO, SCK, above are described in the following paragraphs. Each signal function is described for both the master and slave mode.

HIP7030A2 SLAVE 0

MISO MOSI

SCK

0 1

PORT

2 3

HIP7030A2 SLAVE 3 HIP7030A2 SLAVE 2 HIP7030A2 SLAVE 1

FIGURE 20. MASTER-SLAVE SYSTEM CONFIGURATION (SINGLE MASTER, FOUR SLAVES)

MISO MOSI SCK

SSMISO MOSI SCK SS

MISO MOSI SCK

MISO MOSI SCK SS

SS) discussed

Page 28

HIP7030A2

Master Out Slave In (MOSI)

The MOSI pin is conﬁgured as a data output in a master (mode) device and as a data input in a slave (mode) device. In this manner data is transferred serially from a master to a slave on this line; most signiﬁcant bit ﬁrst, least signiﬁcant bit last. The timing diagrams of Figure 21 summarize the SPI timing and show the relationship between data and clock (SCK). As shown in Figure 21, four possible timing relationships may be chosen by using control bits CPOL and CPHA. The master device always allows data to be applied on the MOSI line a half-cycle before the clock edge (SCK) in order for the slave device to latch the data.

NOTE: Both the slave device(s) and a master device must be pro-

grammed to similar timing modes for proper data transfer.

When the master device transmits data to a second (slave) device via the MOSI line, the slav e de vice responds b y sending data to the master device via the MISO line. This implies full duplex transmission with both data out and data in synchronized with the same clock signal (one which is provided by the master device). Thus, the byte transmitted is replaced by the byte received and eliminates the need for separate transmit-empty and receiver-full status bits. A single status bit (SPIF) is used to signify that the I/O operation is complete. Conﬁguration of the MOSI pin is a function of the MSTR bit in the serial peripheral control register (SPCR, location $0A). When a device is operating as a master, the MOSI pin is an output because the program in ﬁrmware sets the MSTR bit to a logic one.

Master In Slave Out (MISO)

The MISO pin is conﬁgured as an input in a master (mode) device and as an output in a slave (mode) device. In this manner data is transferred serially from a slave to a master on this line; most signiﬁcant bit ﬁrst, least signiﬁcant bit last. The MISO pin of a slave device is placed in the high-impedance state if it is not selected by the master; i.e., its SS pin is a logic one. The timing diagram of Figure 21 shows the relationship between data and clock (SCK). As shown in Figure 21, four possible timing relationships may be chosen by using control bits CPOL and CPHA. The master device always allows data to be applied on the MOSI line a halfcycle before the clock edge (SCK) in order for the slave device to latch the data.

NOTE: The slave device(s) and a master device must be pro-

grammed to similar timing modes for proper data transfer.

When the master device transmits data to a slave device via the MOSI line, the slave device responds by sending data to the master device via the MISO line. This implies full duplex transmission with both data out and data in synchronized with the same clock signal (one which is provided by the master device). Thus, the byte transmitted is replaced by the byte received and eliminates the need for separate transmitempty and receiver-full status bits. A single status bit (SPIF) in the serial peripheral status register (SPSR, location $0B) is used to signify that the I/O operation is complete.

In the master device, the MSTR control bit in the serial peripheral control register (SPCR, location $0A) is set to a logic one (by the program) to allow the master de vice to receive data on its MISO pin. In the slave de vice, its MISO pin is enab le b y the logic level of the SS pin; i.e., if SS = 1 then the MISO pin is placed in the high-impedance state, whereas, if SS = 0 the MISO pin is an output for the slav e device.

SCK

MISO/

MOSI

(CPOL = 0, CPHA = 0)

(CPOL = 0, CPHA = 1)

(CPOL = 1, CPHA = 0)

(CPOL = 1, CPHA = 1)

MSB654321LSB

MSB IF CPHA = 0

INTERNAL STROBE FOR DATA CAPTURE (ALL MODES)

FIGURE 21. DATA CLOCK TIMING DIAGRAM

Page 29

HIP7030A2

Serial Clock (SCK)

The serial clock is used to synchronize the movement of data both in and out of the device through its MOSI and MISO pins. The master and slave devices are capable of exchanging a data byte of information during a sequence of eight clock pulses. The SCK is generated by the master device, is an input on all slave de vices, and synchronizes master/sla v e data transfers. The type of clock and its relationship to data are controlled by the CPOL and CPHA bits in the Serial Peripheral Control Register (SPCR, location $0A) discussed below. Refer to Figure 21 for timing.

The master device generates the SCK through a circuit driven by the internal processor clock. Two bits (SPR0 and SPR1) in the SPCR of the master device select the clock rate. The master device uses the SCK to latch incoming slave device data on the MISO line and shifts out data to the slave device on the MOSI line. Both master and slave devices must be operated in the same timing mode as controlled by the CPOL and CPHA bits in the SPCR. In slave devices, SPR0, SPR1 hav e no eff ect on the operation of SPI. Timing is shown in Figure 21.

INTERNAL

PROCESSOR

CLOCK

Slave Select (

The slave select (

SS)

SS) pin is a ﬁxed input, which receives an active low signal to enable slave device(s) to transfer data. A high level

SS signal forces the MISO line to the high-impedance state. Also, SCK and MOSI are ignored by a slave device when its

SS signal is high. The SS signal must be driven low prior to the ﬁrst SCK and must remain low throughout a transfer. The

SS input on a Master must be held high at all times (see description of MODF under Serial Peripheral Status Register for more details).

As shown in Figure 21, with CPHA = 0, the ﬁrst bit of data must be applied to the MISO line prior to the ﬁrst transition of the SCK. In this case,

SS going low is used to provide the ﬁrst clock edge of a transfer. A device is prevented from writing to its SPI data register while

SS is low and CPHA = 0

(see description of WCOL under Serial Peripheral Status

When CPHA = 1, the

SS of a slave can be held low throughout a series of SPI transfers and in a single slave system can even be permanently wired low.

SEE NOTES

MISOMOSISCK

SS go

READ

RATE

GENERATOR

(SEE NOTE 4)

NOTES: The SS, SCK, MOSI, and MISO are external pins which provide the following functions:

1. MOSI - Provides serial output to slave unit(s) when de vice is conﬁgured as a master. Receives serial input from master unit when device is conﬁgured as a slave unit.

2. MISO - Provides serial input from slave unit(s) when device is configured as a master. Receives serial output to master unit when device is configured as a slave unit.

3. SCK - Provides system clock when device is configured as a master. Receives system clock when device is configured as a slave unit.

4. SS - Provides a logic low to select device for a transfer with the master.

SPCR

MASTER

START LOGIC

SLAVE

START LOGIC

CONTROL

$0A

BITS

FIGURE 22. SERIAL PERIPHERAL INTERFACE (SPI) BLOCK DIAGRAM

SPSR

$0B

READ BUFFER

$0C

8-BIT SHIFT

WRITE

CONTROLLER

(LOAD)

(FULL)

STATE

FLAGS

SPIF (END TX)

INTERNAL DATA BUS

Page 30

HIP7030A2

When a device is a master, it constantly monitors its

SS signal input for a logic low. The master device will become a slave device an y time its ensures that there is only one master controlling the for a particular system. When the

SS signal input is detected low. This

SS line

SS line is detected low, it clears the MSTR control bit (serial peripheral control register, location $0A). Also, control bit SPE in the serial peripheral control register is cleared which causes the serial peripheral interface (SPI) to be disabled. The MODF ﬂag bit in the serial peripheral status register (location $0B) is also set to indicate to the master device that another device is attempting to become a master. Two devices attempting to be outputs are normally the result of a software error; however, a system could be conﬁgured which would contain a default master which would automatically “take-over” and restart the system.

Functional Description

A block diagram of the serial peripheral interface (SPI) is sho wn in Figure 22. In a master conﬁguration, the master start logic receives an input from the CPU (in the form of a write to the SPI rate generator) and originates the system clock (SCK) based on the internal processor clock. This clock is also used internally to control the state controller as well as the 8-bit shift register. As a master de vice, data is parallel loaded into the 8-bit shift register (from the internal bus) during a write cycle, data is applied serially from a slave device via the MISO pin to the 8-bit shift register. After the 8-bit shift register is loaded, its data is parallel transferred to the read buff er and then is made av ailable to the internal data bus during a CPU read cycle.

In a slave conﬁguration, the slave start logic receives a logic low (from a master device) at the input (from the same master device) at the SCK pin. Thus, the slave is synchronized with the master. Data from the master is received serially at the slave MOSI pin and loads the 8-bit shift register. After the 8-bit shift register is loaded, its data is parallel transferred to the read buffer and then is made available to the internal data bus during a CPU read cycle. During a write cycle, data is parallel loaded into the 8-bit shift register from the internal data bus and then shifted out serially to the MISO pin for application to the master device.

Figure 23 illustrates the MOSI, MISO, and SCK master-slave interconnections. Note that in Figure 23 the master tied to a logic high and the slave 20 provides a larger system connection for these same pins. Note that in Figure 20, all pin of a master/slave device. In this case any of the devices can be a slave.

SS pin and a system clock

SS pin is

SS pin is a logic low. Figure

SS pins are connected to a port

MASTER SLAVE

8-BIT SHIFT

SPI

CLOCK

GENERATOR

FIGURE 23. SERIAL PERIPHERAL INTERFACE (SPI) MASTER-

SLAVE INTERCONNECTION

MISO MISO

MOSI MOSI

SCK SCK SS SS

+5V

8-BIT SHIFT

Registers

There are three registers in the serial parallel interface which provide control, status, and data storage functions. These registers which include the serial peripheral control register (SPCR, location $0A), serial peripheral status register (SPSR, location $0B), and serial peripheral data I/O register (SPDR, location $0C) are described below.

Serial Peripheral Control Register (SPCR)

The serial peripheral control register bits are deﬁned as follows:

76543210

SPIE SPE - MSTR CPOL CPHA SPR1 SPR0

SPCR (LOCATION $0A)

B7, SPIE When the serial peripheral interrupt enable is

high, it allows the occurrence of a processor interrupt, and forces the proper vector to be loaded into the program counter if the serial peripheral status register ﬂag bit (SPIF and/or MODE) is set to a logic one. It does not inhibit the setting of a status bit. The SPIE bit is cleared by RESET.

B6, SPE When the serial peripheral output enable control

bit is set, all output drive is applied to the external pins and the system is enabled. When the SPE bit is set, it enables the SPI system by connecting it to the external pins thus, allowing it to interface with the external SPI bus. The pins that are deﬁned as output depend on which mode (master or slave) the de vice is in. When SPE is lo w, all pins appear as inputs to the external system. Because the SPE bit is cleared by RESET, the SPI system is not connected to the external pins upon RESET.

B4, MSTR The master bit determines whether the device is a

master or a slave. If the MSTR bit is a logic zero it indicates a slave device and a logic one denotes a master device. If the master mode is selected, the function of the SCK pin changes from an input to an output and the function of the MISO and MOSI pins are reversed. This allows the user to wire device pins MISO to MISO, and MOSI to MOSI, and SCK to SCK without incident. The MSTR bit is cleared by RESET; therefore, the device is always placed in the slave mode during RESET.

Page 31

HIP7030A2

B3, CPOLThe clock polarity bit controls the normal or steady

state value of the clock when data is not being transferred. The CPOL bit affects both the master and slave modes. It must be used in conjunction with the clock phase control bit (CPHA) to produce the wanted clock-data relationship between a master and a slave device. When the CPOL bit is a logic zero, it produces a steady state low value at the SCK pin of the master device. If the CPOL bit is a logic one, a high value is produced at the SCK pin of the master device when data is not being transferred. The CPOL bit is not affected by RESET. Refer to Figure 21.

B2, CPHAThe clock phase bit controls the relationship

between the data on the MISO and MOSI pins and the clock produced or received at the SCK pin. This control has effect in both the master and slave modes. It must be used in conjunction with the clock polarity control bit (CPOL) to produce the wanted clock-data relation. The CPHA bit in general selects the clock edge which captures data and allows it to change states. It has its greatest impact on the ﬁrst bit transmitted (MSB) in that it does or does not allow a clock transition before the ﬁrst data capture edge. The CPHA bit is not affected by RESET. Refer to Figure 21.

B1, SPR1; B0, SPR0

These two serial peripheral rate bits select one of four baud rates to used as SCK if the device is a master; however they have no effect in the slave mode. The slave device is capable of shifting data in and out at a maximum rate which is equal to the CPU clock. A rate table is given belo w for the generation of the SCK from the master. The SPR1 and SPR0 bits are not affected by RESET.

SPR1 SPR0

00 2 01 4 10 16 11 32

INTERNAL PROCESSOR

CLOCK DIVIDE BY

Serial Peripheral Status Register (SPSR)

The status ﬂags which generate a serial peripheral interface (SPI) interrupt may be blocked by the SPIE control bit in the serial peripheral control register. The WCOL bit does not cause an interrupt. The serial peripheral status register bits are deﬁned as follows:

76543210

SPIF WCOL 0 MODF 0000

SPSR (LOCATION $0B)

B7, SPIF The serial peripheral data transfer ﬂag bit notiﬁes the

user that a data transfer between the device and an external device has been completed. With the completion of the data transfer, SPIF is set, and if SPIE

is set, a serial peripheral interrupt (SPI) is generated. During the clock cycle that SPIF is being set, a copy of the received data byte in the shift register is moved to a buffer. When the data register is read, it is the buffer that is read. During an overrun condition, when the master device has sent several bytes of data and the slave device has not responded to the ﬁrst SPIF, only the ﬁrst byte sent is contained in the receiver buff er and all other bytes are lost.

The transfer of data is initiated by the master device writing its serial peripheral data register.

Clearing the SPIF bit is accomplished by a software sequence of accessing the serial peripheral status register while SPIF is set and followed by a write to or a read of the serial peripheral data register. While SPIF is set, all writes to the serial peripheral data register are inhibited until the serial peripheral status register is read. This occurs in the master device. In the slave device, SPIF can be cleared (using a similar sequence) during a second transmission; howev er, it must be cleared before the second SPIF in order to prevent an overrun condition. The SPIF bit is cleared by RESET.

B6, WCOL

The function of the write collision status bit is to notify the user that an attempt was made to write the serial peripheral data register while a data transfer was taking place with an external device. The transfer continues uninterrupted; therefore, a write will be unsuccessful. A “read collision” will never occur since the receiv ed data byte is placed in a buffer in which access is always synchronous with the MCU operation. If a “write collision” occurs, WCOL is set but no SPI interrupt is generated. The WCOL bit is a status ﬂag only.

Clearing the WCOL bit is accomplished by a software sequence of accessing the serial peripheral status register while WCOL is set, followed by 1) a read of the serial peripheral data register prior to the SPIF bit being set, or 2) a read or write of the serial peripheral data register after the SPIF bit is set. A write to the serial peripheral data register (SPDR) prior to the SPIF bit being set, will result in generation of another WCOL status ﬂag. Both the SPIF and WCOL bits will be cleared in the same sequence. If a second transfer hasstarted while trying to clear (the previously set) SPIF and WCOL bits with a clearing sequence containing a write to the serial peripheral data register, only the SPIF bit will be cleared.

A collision of a write to the serial peripheral data register while an external data transfer is taking place can occur in both the master mode and the slave mode, although with proper progr amming the master device should have sufﬁcient information to preclude this collision.

Page 32

HIP7030A2

Collision in the master device is deﬁned as a write of the serial peripheral data register while the internal rate clock (SCK) is in the process of transfer. The signal on the on the master device.

A collision in a slave de vice is deﬁned in tw o separate modes. One problem arises in a slave device when the CPHA control bit is a logic zero. When CPHA is a logic zero, data is latched with the occurrence of the ﬁrst clock transition. The slave device does not have any way of knowing when that transition will occur; therefore, the slave device collision occurs when it attempts to write the serial peripheral data register after its SS pin has been pulled low. The SS pin of the slave device freezes the data in its serial peripheral data register and does not allow it to be altered if the CPHA bit is a logic zero. The master device must raise the high between each byte it transfers to the slave device.

The second collision mode is deﬁned for the state of the CPHA control bit being a logic one. With the CPHA bit set, the slave device will be receiving a clock (SCK) edge prior to the latch of the ﬁrst data transfer. This ﬁrst clock edge will freeze the data in the slave device I/O register and allow the MSB onto the external MISO pin of the slave device. The the slave device but the drive onto the MISO pin does not take place until the ﬁrst data transfer clock edge. The WCOL bit will only be set if the I/O register is accessed while a transfer is taking place. By deﬁnition of the second collision mode, a master device might hold a slave device low during a transfer of several bytes of data without a problem.

A special case of WCOL occurs in the slave device. This happens when the master device starts a transfer sequence (an edge on SCK for CPHA = 1; or an active

0) at the same time the slave device CPU is writing to its serial peripheral interface data register. In this case it is assumed that the data byte written (in the slave device serial peripheral interface) is lost and the contents of the slave device read buffer becomes the byte that is transferred. Because the master device receives back the last byte transmitted, the master device can detect that a fatal WCOL occurred.

Since the slave device is operating asynchronously with the master device, the WCOL bit ma y be used as an indicator of a collision occurrence. This helps alleviate the user from a strict realtime programming effort. The WCOL bit is cleared by RESET.

B4, MODF The function of the mode fault ﬂag is deﬁned f or the

master mode (device). If the device is a slave device the MODF bit will be prev ented from toggling

SS pin is always high

SS pin of the slave device

SS pin low state enables

SS pin

SS transition for CPHA =

from a logic zero to a logic one; however, this does not prevent the device from being in the slave mode with the MODF bit set. The MODF bit is normally a logic zero and is set only when the master device has its the MODF bit to a logic one affects the internal serial peripheral interface (SPI) system in the following ways:

1. MODF is set and SPI interrupt is generated if SPIE = 1.

2.The SPE bit is forced to a logic zero. This blocks all output drive from the device, disables the SPI system.

3.The MSTR bit is forced to a logic zero, thus , f orcing the device into the slave mode.

Clearing the MODF is accomplished by a software sequence of accessing the serial peripheral status register while MODF is set followed by a write to the serial peripheral control register. Control bit SPE and MSTR may be restored to their original set state during this cleared sequence or after the MODF bit has been cleared. Hardware does not allow the user to set the SPE and MSTR bit while MODF is a logic one unless it is during the proper clearing sequence. The MODF ﬂag bit indicates that there might have been a multi-master conﬂict for system control and allows a proper exit from system operation to a RESET or default system state. The MODF bit is cleared by RESET.

Serial Peripheral Data I/O Register (SPDR)

76543210

Serial Peripheral Data I/O Register

SPDR (LOCATION $0C)

The serial peripheral data I/O register is used to transmit and receive data on the serial bus. Only a write to this register will initiate transmission/reception of another byte and this will only occur in the master device. A slave device writing to its data I/O register will not initiate a transmission. At the completion of transmitting a byte of data, the SPIF status bit is set in both the master and slave devices . A write or read of the serial peripheral data I/O register, after accessing the serial peripheral status register with SPIF set, will clear SPIF.

During the clock cycle that the SPIF bit is being set, a copy of the received data byte in the shift register is being moved to a buffer. When the user reads the serial peripheral data I/O register, the buffer is actually being read. During an overrun condition, when the master device has sent several bytes of data and the slave device has not internally responded to clear the ﬁrst SPIF, only the ﬁrst byte is contained in the receive buffer of the slave device; all others are lost. The user may read the buffer at any time. The ﬁrst SPIF must be cleared by the time a second transfer of data from the shift register to the read buffer is initiated or an overrun condition will exist.

A write to the serial peripheral data I/O register is not buffered and places data directly into the shift register for transmission.

SS pin pulled low. Toggling

Page 33

HIP7030A2

The ability to access the serial peripheral data I/O register is limited when a transmission is taking place. It is important to read the discussion deﬁning the WCOL and SPIF status bit to understand the limits on using the serial peripheral data I/O register.

Serial Peripheral Interface (SPI) System Considerations

There are two types of SPI systems; single master system and multi-master systems. Figure 20 illustrates a single master system and a discussion of both is provided below.

Figure 20 illustrates how a typical single master system may be conﬁgured, using a CDP68HC05 family device as the master and four CDP68HC05 family devices as slaves. As shown, the MOSI, MISO, and SCK pins are all wired to equivalent pins on each of the ﬁve devices. The master device generates the SCK clock, the slave device all receive it. Since the CDP68HC05 master device is the bus master, it internally controls the function of its MOSI and MISO lines, thus, writing data to the slave devices on the MOSI and reading data from the slave devices on the MISO lines. The master device selects the individual slave devices by using four pins of a parallel port to control the four slave devices. A slave device is selected when the master device pulls its ing RESET since the master device ports will be forced to be inputs at that time, thus, disabling the slave devices. Note that the slave devices do not have to be enabled in a mutually exclusive fashion except to prevent bus contention on the MISO line. For example, three slave devices, enabled for a transfer, are permissible if only one has the capability of being read by the master. An example of this is a write to several display drivers to clear a display with a single I/O operation. To ensure that proper data transmission is occurring between the master device and a slave device, the master device may have the slave device respond with a previously received data byte (this data byte could be inverted or at least be a byte that is different from the last one sent by the master device). The master device will always receive the previous byte back from the slave device if all MISO and MOSI lines are connected and the slave has not written its data I/O register. Other transmission security methods might be deﬁned using ports for handshake lines or data bytes with command ﬁelds.

A multi-master system may also be conﬁgured by the user. An exchange of master control could be implemented using a handshake method through the I/O ports or by an exchange of code messages through the serial peripheral interface system. The major device control that plays a part in this system is the MSTR bit in the serial peripheral control register and the MODF bit in the serial peripheral status register.

SS pin low. The SS pins are pulled high dur-

SS pins of the

J1850 VPW Messaging

This section provides an introduction to J1850 multiplexed communications. It is assumed that the user is or will become familiar with the appropriate documents published by the Society of Automotive Engineering (SAE). The following discussion is not comprehensive.

Overview

The SAE J1850 Standard (Note 1) (J1850) establishes the requirements for communications on a Class B multiplexed wiring network for automotive applications. The J1850 document details the requirements in a three layer description which separately speciﬁes the characteristics of the

layer

, the

data link layer

several options within each layer which allows vehicle manufacturers to customize the network while still maintaining a level of universality.

NOTE:

1. SAE J1850 Standard, Class B Data Communication Netw ork Interface, May 1994, Society of Automotive Engineers Inc.

The hardware of the Intersil HIP7030A2 provides features which facilitate implementation of the 10.4Kbps Variable Pulse Width Modulated (VPW) physical layer option of J1850. In combination with a bus transceiver, such as the Intersil J1850 Bus Transceiver HIP7020, and appropriate software algorithms the HIP7030A2 circuitry enables the designer to completely implement a 10.4Kbps VPW Class B Communications Network Interface per J1850. Features of such an implementation include:

• Single Wire 10.4Kbps Communications

• Message Buffering and Message Filtering

• Bit-by-Bit Bus Arbitration

• Industry Standard Protocol

• Message Acknowledgment (“In-Frame Response”) Capabilities

• Exceptionally Tolerant of Clock Skew, System Noise, and Ground Offsets

• Meets CARB and EPA Diagnostic Requirements

• Supports up to 32 Nodes

• Low Error Rates

• Excellent EMC Levels (when interfaced via Intersil J1850 Bus Transceiver HIP7020)

In addition to the standard J1850 features, the HIP7030A2 hardware provides a high speed mode, (intended for receive only use) which can signiﬁcantly enhance vehicle maintenance capabilities. The high speed mode provides a

41.6Kbps communications path to any node built with the

HIP7030A2.

Anatomy of a J1850 VPW Message

All messages in a J1850 VPW system are sent along a single wire, shared bus. At any given moment the bus can be in either of two states: nodes are connected to the bus as a “wired-OR” network in which the bus is high if an active output. The bus is only low when erating active outputs. It follows that, when no communications are taking place the bus will rest in the passive state. A message begins when the bus is ﬁrst driven to the high state. Each succeeding state transition (i.e., a change from active to passive or passive to active) transfers one bit of information (

symbol

) until the message is complete and the bus once again rests at the passive state. The interpretation of each symbol in the message is dependent on its duration (and state), hence, the descriptor Variable Pulse Width (VPW).

, and the

active

any

application layer

(high) or

one (or more) node is generating

passive

physical

. There are

(low). Multiple

nodes are gen-

Page 34

HIP7030A2

SOF HEADER DATA 1 DATA 2 CRC EOD

EOF

FIGURE 24. TYPICAL J1850 VPW MESSAGE FRAME

Each message has a beginning and an end, the span of which encompasses the entire Figure 24). A frame consists of an active (SOF) symbol and a passive

message

end of frame

frame

(refer to

start of frame

(EOF) symbol sandwiched around a series of byte sized (8-bit) groups of symbols. The ﬁrst byte of the frame contents is always a

header

byte, followed by possibly additional header bytes, followed by one or more check byte (

CRC

byte), followed by a passive

(EOD) symbol, followed by possibly one or more

response

(IFR) bytes. To keep waiting times low, messages

data

bytes, followed by an integrity

end of data

in-frame-

are limited to 12 bytes total (including header, data, check, and IFR bytes). All message bytes are transmitted most signiﬁcant bit (MSB) ﬁrst.

VPW Symbol Deﬁnitions

Within the J1850 scheme, symbols are deﬁned in terms of both duration and state (passive or active). The duration is measured as the time between successive transitions. There is one transition per symbol and one symbol per transition. The end of one symbol marks the beginning of the next. Since the bus is passive when a message begins and must return to that same state when the message completes, all frames have an even number of transitions and hence an even number of symbols.

There are unique deﬁnitions for data bit symbols (all the symbols which occur within the header, data, and check bytes) and protocol symbols (including SOF, EOD, and EOF). The duration of each symbol is expressed in terms of VPW Timing Pulses (TV values). Table 5 summarizes the TV deﬁnitions. Each TV is speciﬁed in terms of a ideal) duration and a

minimum

and

maximum

nominal

(or

duration. The span between the minimum and maximum limits accommodates system noise sources such as node to node clock skew, ground offsets, clock jitter, and electromechanical noise. There are no dead zones between the maximum of one TV and the minimum of the next.

TABLE 5. J1850 TV DEFINITIONS

DURATION

(ALL TIMES IN MICROSECONDS)

TV ID

Illegal 0 NA ≤34

TV1 >34 64 ≤96 TV2 >96 128 ≤163 TV3 >163 200 ≤239 TV4 >239 280 NA TV5 >239 300 NA TV6 >280 300 NA

MINIMUM NOMINAL MAXIMUM

The terms

short

and

long

are often used to refer to pulses of

duration TV1 and TV2 respectively. VPW is a non-return-to-zero (NRZ) protocol in which each

transition represents a complete bit of information. Accordingly, a pulse and sometimes as an active pulse. Similarly, a

data bit will sometimes be transmitted as a passive

data bit will sometimes be transmitted as a passive pulse and sometimes as an active pulse. In order to accommodate arbitration (see Bus Arbitration) a sents a 0 data bit and a

short active

data bit. Complementing this fact, a resents a 0 and a

long passive

long active

pulse repre-

pulse represents a 1

short passive

pulse rep-

pulse represents a 1. Starting from a transition to the active state, a 0 data bit will maintain the active level longer than a 1. Similarly, starting from a transition to the passive state, a 0 data bit will return to the active level quicker than a 1. These facts give rise to the dominance of 0’s over 1’s on the J1850 bus as depicted in Figure 25. See Bus Arbitration for additional details.

SYNCHRONIZED

BITDA T A0

BITDA T A1

BUSJ1850

FIGURE 25A. DOMINANCE OF ACTIVE 0 DATA BIT

BITDA T A0

BITDA T A1

BUSJ1850

FIGURE 25B. DOMINANCE OF PASSIVE 0 DATA BIT

SYNCHRONIZED

LONGER ACTIVE PULSE (0) CONTROLS THE BUS

SHORTER PASSIVE PULSE (0) CONTROLS THE BUS

Page 35

HIP7030A2

Table 6 summarizes the complete set of symbol deﬁnitions based on duration and state.

TABLE 6. J1850 SYMBOL DEFINITIONS

SYMBOL DEFINITION

0 Data 1 Data SOF (Start of Frame) Active TV3 EOD (End of Data) Passive TV3 EOF (End of Frame) Passive TV4 IFS (Inter-Frame Separation) Passive TV6 IDLE (Idle Bus) Passive >TV6 nom NB (Normalization Bit) BRK (Break) Active TV5

Passive TV1 or Active TV2 Active TV1 or Passive TV2

Active TV1 or Active TV2

In Frame Response (IFR)

The distinction between two of the passive symbols, EOD and EOF, is subtle but impor tant (refer to Figure 26). The EOD (TV3) interval signiﬁes that the originator of the message is done broadcasting and any nodes which have been requested to respond (i.e., to acknowledge receipt of the message) can now do so. The EOD interval begins when the transmitting node has completed sending the eighth bit of the check byte. The transmitter simply releases the bus and allows it to revert to a passive state. In the course of normal messaging, no node can seize the bus until an EOD time has been detected. Once an EOD has elapsed, any nodes which are scheduled to produce an IFR will arbitrate for control of the bus (see Bus Arbitration) and respond appropriately. If no responses are forthcoming the bus remains in the passive state until an EOF (TV4) interval has elapsed. After the EOF has been generated, the frame is considered closed and the next communications on the bus will represent a totally new message.

IFRs can consist of multiple bytes from a single respondent, one byte from a single respondent, or one byte from multiple respondents. In all cases the ﬁrst response byte must be preceded by a

response

normalization bit (NB)

which serves as a

start of

symbol and places the bus in an active state so that

following the IFR byte(s) the b us will be left in the passivestate. The NB symbol is by deﬁnition active, but can be either TV1

or TV2 in duration. The long variety (TV2) signiﬁes the IFR contains a CRC byte. The short variety (TV1) precedes an IFR without CRC.

Message Types

• Type 2 - One byte IFRs from multiple respondents (no

CRC byte)

• Type 3 - Multiple byte IFR from a single respondent (CRC

appended)

Bus Arbitration

The nature of multiplexed communications leads to contention issues when two or more nodes attempt to transmit on the bus simultaneously. Within J1850 VPW systems, messages are assigned varying levels of priority which allows implementation of an arbitration scheme to resolve potential contentions. The speciﬁed arbitration is performed on a symbol by symbol basis throughout the duration of every message.

Arbitration begins with the rising edge of the SOF pulse. No node should attempt to issue an SOF until an Idle bus has been detected (i.e., an

Inter-Frame Separation (IFS)

symbol with a period of TV6 has been received). If multiple nodes are ready to access the bus and are all waiting for an IFS to elapse, invariable skews in timing components will cause one arbitrary node to detect the Idle condition before all others and start transmission ﬁrst. For this reason, all nodes waiting for an IFS will consider an IFS to have occurred if either:

- An IFS nominal period has elapsed or,

- An EOF minimum period has elapsed and a rising edge has been detected

Arbitrating devices will all be synchronized during the SOF. Beginning with the ﬁrst data bit and continuing to the EOF, every transmitting device is responsible for verifying that the symbol it sent was the symbol which appeared on the bus. Each transition, every transmitting node must decode the symbol, verify the received symbol matches the one sent, and begin timing of the next symbol. Since timing of the next symbol begins with the last transition detected on the bus, all transmitters are re-synchronized each symbol. When the received symbol doesn’t match the symbol sent, a conﬂict (

collision

) occurs. Any device detecting a collision will assume

bit

it has lost arbitration and immediately relinquish the bus. Typically, after losing arbitration, a device will attempt re-transmission of the message when the bus once again becomes Idle.

The deﬁnition of 1 and 0 data bits (see Table 6 and discussion under VPW Symbol Deﬁnitions) leads to 0’s having priority over 1’s in this arbitration scheme. Header bytes are generally assigned such that arbitration is completed before the ﬁrst data byte is transmitted. Because of the dominance of 0-bits and the MSB ﬁrst bit order, a header with the hexadecimal value $00 will have highest priority, then $01, $02, $03, etc. An example of two nodes arbitrating for control of the bus is shown in Figure 27.

Messages are classiﬁed into one of four

Types

according to whether the message has an IFR and what kind of IFR it is. The deﬁnitions are:

• Type 0 - No IFR

• Type 1 - One byte IFR from a single respondent (no CRC

byte)

Page 36

HIP7030A2

SOF HEADER . . . . DATA N CRC IN FRAME RESPONSEEOD

FIGURE 26. J1850 MESSAGE WITH IN-FRAME-RESPONSE

000 01

TRANSMITTER A

TRANSMITTER B

J1850 BUS

FIGURE 27. TWO NODES ARBITRATING FOR CONTROL OF J1850 BUS

000

SOF

HEADER (1 OR 3 BYTES)

COLLISION DETECTEDBY B

Arbitration also takes place during the IFR portion of a message, if more than one node is attempting to generate a response. Arbitration begins with the NB symbol, which follows the EOD and precedes the ﬁrst IFR byte.

For Type 1 and Type 3 messages only the respondent which successfully arbitrates for control of the bus produces an IFR. All other respondents abort their IFRs.

For Type 2 messages, all respondents which lose arbitration must count symbols and re-attempt transmission at the end of each byte. Each node, which successfully responds, eliminates itself from the subsequent arbitration until all nodes have responded. This arbitration scheme limits each respondent to a single byte during a Type 2 IFR.

Break

To force a message to be aborted before EOF is reached, a break (BRK) symbol can be transmitted by any node. The BRK symbol is an active pulse of duration TV5. Reception of a break causes all nodes to reset to a

ready-to-receive

state

and to re-arbitrate for control following an IFS.

Variable Pulse Width Symbol Encoder Decoder (SENDEC)

Overview Of SENDEC Operation

The SENDEC hardware integrated in the HIP7030A2 facilitates generation and reception of J1850 messages on a symbol by symbol basis. Symbols are output from the SENDEC, as a digital signal, on the VPWOUT pin and input, as a digital signal, on the connected through a bus transceiver (such as the Intersil J1850 Bus Transceiver HIP7020) to the single wire J1850 bus. The transceiver is responsible for generating and receiving waveforms consistent with the physical layer speciﬁcations of J1850. In addition, the transceiver is responsible for providing isolation from bus transients.

VPWIN pin. These two lines must be

EOD

DATA 1 . . . DATA N CRC EOFIFS

EOF

Every symbol sent out on the VPWOUT is in effect inverted and echoed back on the

VPWIN pin after some ﬁnite delay through the transceiver . In actuality, only long active symbols are guaranteed to be echoed unchanged. If the transmitted symbol is passive and another node is simultaneously sending an active symbol, the active symbol will dominate and pull the bus to a high level.

The SENDEC circuitry includes a 3-bit digital ﬁlter which effectively ﬁlters out noise pulses less than 7µs in duration.

Communications between the CPU and the SENDEC are via three registers mapped into Page 0 of the MCUs memory space.

When transmitting symbols, the desired symbol is speciﬁed by writing an appropriate code to the SENDEC Data Register (SEDDR). Timing of each symbol is calculated from the last transition on the

VPWIN line. Each write to the SEDDR, which occurs within 34µs of the last received transition, will enable the VPWOUT pin and the SENDEC automatically produces a transition on the VPWOUT pin after the proper delay (the seven microseconds added by the digital ﬁlter and a 17µs delay through the bus transceiver are compensated for). The VPWOUT pin remains active until 34µs after the last received transition. Failure to write a new symbol during the 34µs window causes the VPWOUT pin to go low until the next valid write or until the Force Start of F rame (FSOF) bit is set in the SENDEC Data Register (SEDDR).

Decoding of received symbols is automatically performed by the SENDEC. The decoded symbol is valid until the next transition occurs. The value can be read via the SEDDR.

Generally the SENDEC is programmed to interrupt the MCU with each transition on the

VPWIN pin. When the SENDEC is receiving a message, the interrupt signals that a new symbol has been received and appropriate actions must be taken to read and process the symbol. When the SENDEC is transmitting, the transition interrupt signiﬁes that the reﬂected symbol has been received, and it is time to start

Page 37

HIP7030A2

timing the next symbol. The reﬂected symbol should be read and compared to the previously sent one. If the reﬂected symbol doesn’t match the symbol sent, a collision has occurred and the software must cease transmissions until the next idle period. If there was no collision, the new symbol must be immediately (within one TV1 minimum time) written to the SEDDR (the SEDDR is not buffered).

In addition to features already discussed, the SENDEC includes, noise detection, idle bus detection, a clock prescaler, an echo fail detector, a wake-up facility, and a high speed receive mode. Symbol timing is based on the main MCU oscillator. The programmable prescaler allows proper SENDEC operation with 10MHz, 8MHz, or 4MHz oscillators. The high speed receive mode is a J1850 extension which allows maintenance equipment to transmit messages at 4X the normal 10.4Kbps rate.

Software algorithms can be employed to implement message buffering and ﬁltering, CRC generation and detection, IFR handling, and other needed features to create a complete J1850 VPW node. See the

Applications

section for typ-

ical algorithms.

SENDEC Registers

The SENDEC register set consists of the read-write SENDEC Data Register (SEDDR), the read-write SENDEC Control Register (SEDCR), and the read-only SENDEC Status Register (SEDSR). A detailed description of the operation of each follows:

SENDEC Control Register (SEDCR)

The SENDEC Control Register (SEDCR, location $0F) is an 8-bit read/write register which contains ﬁve control bits. One of the bits controls interrupts which are associated with a ﬂag bit in the SENDEC Status Register (discussed following). Three bits control the clock prescaler and the high speed 4X mode of the SENDEC. The ﬁnal bit doesn’t directly control the SENDEC, rather it controls the start-up delay following exit from the STOP mode of the processor. The bit assignments are illustrated below, followed by a detailed description of each bit.

76543210

TXIE - - NDEL - 4X PRE1 PRE0

SEDCR (LOCATION $0F)

B7, TXIE If the transition interr upt enable (TXIE) bit is set,

the MCU will receive a SENDEC interrupt on the occurrence of each transition on the

VPWIN line.

If TXIE is low the TX interrupts are inhibited but the associated ﬂags in the SENDEC Status Register (SEDSR) are still set (see discussion following).

TXIE is cleared by RESET.

B4, NDEL When set, the No Delay (NDEL) bit suppresses

the 4064 t

delay which is normally introduced

CYC

when exiting from the STOP mode via an interrupt. Instead of the 4064 t

delay a 96 t

CYC

delay is introduced. NDEL is intended for applications where the clock source to the HIP7030A2

continues to run when the device enters STOP mode or when a ceramic resonator based oscillator is used. NDEL should not be used when the HIP7030A2 is driven by a quartz crystal based oscillator.

NDEL is cleared by RESET and POR.

B2, 4X When set, the 4X bit causes the SENDEC symbol

timing to be accelerated by a factor of four. Due to ﬁxed delays in the loop back from VPWOUT to VPWIN, the 4X mode is only useful for receiving symbols. 4X mode is intended for high speed data linking between the HIP7030A2 and maintenance or test equipment which has capability to send at the accelerated rate.

Writing to the 4X bit is inhibited except when the NEW bit in the SENDEC Status Register (SEDSR) is set.

Once modiﬁed, the new value of 4X doesn’t take effect until the next transition on the

Receipt of a Break symbol on the

VPWIN pin.

VPWIN line will

automatically clear 4X. RESET and POR clear the 4X bit.

B1, PRE1; B2, PRE0

PRE1 and PRE0 control the SENDEC clock prescaler. The SENDEC circuit requires a fundamental clock of 1MHz. To generate the 1MHz frequency, while allowing a choice of MCU oscillator frequencies, the PRE1 and PRE0 bits must be set to match the OSCIN frequency.

TABLE 7. SENDEC PRESCALER BIT SELECTION

PRE1 PRE0 OSCIN FREQUENCY (MHz)

00 4 01 8 10 10 11 12

Following RESET a window of 4 instructions is allowed for setting the PRE1 and PRE0 bits. Writes to these bits after the fourth instruction have no effect on their values.

Table 7 gives the proper settings of PRE1 and PRE0 for various frequencies.

RESET and POR force PRE1 to a 1 and PRE0 to a 0, selecting the 10MHz mode.

SENDEC Status Register (SEDSR)

The SENDEC Status Register (SEDSR, location $10) is an 8-bit read-only register which contains seven status bits. One of the bits is a ﬂag bit which correspond to the interrupt control bit in the SENDEC Control Register (discussed earlier). Three other bits provide error status information.

Page 38

HIP7030A2

Another two bits provide an indication of special symbols (Break, IFS) occurring on the bus. The ﬁnal bit indicates the transmit status of the SENDEC. The bit assignments are illustrated below, followed b y a detailed description of each bit.

765432 10

TX BRK NEW NOIZ OVR TALK NECHO -

SEDSR (LOCATION $10)

B7, TX The transition (TX) ﬂag bit indicates that a transi-

tion has occurred on the VPWIN line. The line is ﬁrst ﬁltered through the SENDECs 3-bit digital ﬁlter to reject noise.

Once set the TX ﬂag will interrupt the MCU if the TXIE bit in the SEDCR is set and the I bit in the condition code register is clear. TX is cleared by a sequence of ﬁrst reading the SEDSR followed by reading or writing the SENDEC Data Register (SEDDR).

Note that both TX and NEW will be set on the leading edge of an SOF. See description of the NEW ﬂag below.

TX is cleared by RESET.

B6, BRK The break (BRK) bit indicates that a break symbol

has been detected on the at the end of the break symbol, on the active to passive transition.

Once set the BRK ﬂag will interrupt the MCU if the I-bit is cleared in the condition code register. BRK is cleared by a sequence of ﬁrst reading the SEDSR followed b y a read or write of the SEDCR.

BRK is cleared by RESET.

B5, NEW The new frame (NEW) ﬂag indicates that one of

two possible events has been detected on the J1850 bus:

The bus has been passive for at least an IFS nominal symbol time (i.e., the bus is Idle)

or, A transition has occurred on the bus following an

EOF minimum (i.e., another node has started a new message).

NEW is set when either of these events is detected. In the case of a transition following an EOF, the TX bit is also set.

When NEW goes from a 0 to a 1, a SENDEC interrupt will be generated if the I-bit is cleared in the CC register. The NEW interrupt can be cleared under software control by reading the SEDSR followed by reading or writing the SEDCR. This only removes the source of the interrupt and does not clear the NEW bit.

The NEW ﬂag cannot be cleared by software. It is automatically cleared 128 (nominal) microseconds into the next (or current - if NEW was set by a transition following EOF) symbol. This is normally during the SOF of a new message. If the symbol is less than 128µs in duration (an illegal

VPWIN line. BRK is set

SOF symbol), the NEW ﬂag is cleared on the active to passive transition.

Polling NEW provides a convenient means for software to determine that transmission of a new message can be commenced.

NEW is cleared by all resets.

B4, NOIZ The noise (NOIZ) ﬂag indicates that a symbol

shorter than a legal TV1 has been received. NOIZ is cleared by a sequence of ﬁrst reading the SEDSR followed by reading or writing the SEDCR.

NOIZ is cleared by RESET.

B3, OVR The overrun (OVR) ﬂag is set if TALK is set in the

SEDSR and a minimum short symbol time (34µs) has elapsed since the last transition and no write to the SEDDR has taken place. An overrun condition is a serious error and the user should treat it as such. When OVR is set it automatically forces the VPWOUT pin to a low lev el. OVR is cleared by a sequence of ﬁrst reading the SEDSR followed by reading or writing the SEDCR.

Setting of OVR is inhibited while NEW is true in the SEDSR.

OVR is cleared by RESET.

B2, T ALK The transmit (TALK) ﬂag is set if the HIP7030A2 is

actively transmitting symbols via the SENDEC. TALK is set by writing a non-zero to the SEDDR (see

SENDEC Data Register

The TALK bit is cleared by writing a $00 to the SEDDR, when NECHO is set, or when OVR is set.

TALK is cleared by RESET.

B1, NECHO

The No Echo Received (NECHO) ﬂag is set if, during the process of transmitting a symbol, the expected echo of the symbol is not received. This event will cause the VPWOUT pin to be forced to a 0 level. Setting of NECHO automatically clears the TALK bit.

The time required to detect an echo failure is dependent on many factors. The minimum time to detect a failure is 105µs (26µs in 4X mode) and the maximum time to detect afailure is 512µs.

When NECHO goes from a low to a high level, a SENDEC interrupt will be generated if the I-bit is cleared in the CC register. NECHO must go low then high again to generate another interrupt.

NECHO is cleared by a sequence of ﬁrst reading the SEDSR followed by reading or writing the SENDEC Data Register (SEDDR).

NECHO is cleared by all resets.

for details).

Page 39

HIP7030A2

SENDEC Data Register

The SENDEC Data Register (SEDDR, location $11) is an 8bit read/write register which contains one write-only bit, three read/write bits, and four read-only bits. The write only bit triggers SOF symbols required to initiate new transmissions, the three read/write bits are used to specify transmitted symbol durations, and the four read only bits uniquely identify the received J1850 symbol. Reading the SEDDR at anytime provides the received symbol which resulted from the last transition of VPWIn. When writing data to the SEDDR, the value represents the duration of the symbol currently being transmitted. The bit assignments are illustrated below, followed by a detailed description.

765432 10

FSOF S2 S1 S0 LEV R2 R1 R0

SEDDR (LOCATION $11)

B7, FSOF Writing a 1 to the Force Start of Frame (FSOF) bit

while simultaneously writing a non-zero value to S2-0, causes the VPWOUT to immediately go active (high level). The low to high transition will eventually be reﬂected on the

VPWIN line causing a TX interrupt. Upon receipt of the TX interrupt an SOF symbol (S2-0 = 3) must be written to the SEDDR to time the high SOF.

Setting the FSOF bit can only be done when the NEW ﬂag is set in the SENDEC Status Register (NEW is set when the J1850 bus is idle or during the ﬁrst portion of an SOF symbol).

FSOF is a write only bit. Reading FSOF always returns a 0.

B6, S2; B5, S1; B4, S0

When writing to the SEDDR, the three bits (S2-0) determine the transmitted symbol as shown in Table 8. During a write to the SEDDR the S2-0bits are ignored except in three speciﬁc situations:

The NEW ﬂag is high in the SEDSR)

or, A transition has been received on the

VPWIN pin,

from the bus, within the past 34µs

or, S2-0-bits = 0

In the ﬁrst two cases, each write to the SEDDR will produce one properly timed symbol on the VPWOUT pin. The completion of the symbol is

not

reported to the controller,

at the end of the transmitted symbol, but at the end of the symbol echoed back via the

VPWIN input. Writing the FSOF bit, in conjunction with S2-0 = 3, produces the initial transition for the SOF symbol. All timing for a message begins with the receipt of that transition.

Writing a $00, at anytime, immediately disables transmissions (forcing the VPWOUT pin low) and clears the TALK bit in the SEDSR. This is the preferred method to end transmissions.

RESET doesn’t affect S2-S0

TABLE 8. S2-S1 SYMBOL ENCODING

S2 S1 S0 TRANSMIT SYMBOL

0 0 0 Disable Transmit 001 TV1 010 TV2 011 TV3 100 TV1 101 TV1 110 TV1 111 TV1

B3, LEV; B2, R2; B1, R1; B0, R0

These four bits uniquely identify all symbols received via the

VPWIN pin. The symbol decoding map is shown in Table 9. R2-0 represent the duration of the symbol and LEV represents the level of the symbol (active or passive)

These bits are only updated upon detection of a bus transition and therefore reﬂect the last symbol received. An exception to this is for an Idle bus. When an Idle has been detected the values in R2R0 and LEV are immediately updated - no bus transition is necessary.

R2-R0 = 101 with LEV = 0 indicates that the bus is currently Idle.

Note that R2-0 combinations of 110 and 111 will not be produced by the SENDEC. A value of 101 represents all durations equal to and beyond an IFS/IDLE (for the passive case) and a BREAK (for the active case).

RESET does not affect LEV or R2-R0.

When a transition is detected on

VPWIN, the received symbol is decoded and made available for reading via the SEDDR. The TX bit is set in the SEDSR and, if TXIE is high in the SEDCR, an interrupt will be generated. Once the transition is detected the next symbol begins timing out. A new symbol must be written to the SEDDR, before the minimum transmit time for a short symbol has elapsed (34µs). Failure to write to the SEDDR in time will result in the OVR bit being set and transmission aborted. This is a safety precaution to prevent “streaming” messages.

The control routines should verify that the symbol sent matches the symbol received. A mismatch indicates the device has lost control of the bus. It is up to the user code to handle the collision, in terms of disabling the SENDEC, requeueing of the message, ﬁltering the incoming message, etc.

Page 40

HIP7030A2

TABLE 9. R2-R0 AND LEV SYMBOL DECODING

R2 R1 R0 LEV RECEIVE SYMBOL

0000Passive Noise 0001Active Noise 0010TV1 Passive 0011TV1 Active 0100TV2 Passive 0101TV2 Active 0110EOD 0111SOF 1000EOF 1001BREAK 1010IFS/IDLE 1011BREAK 1100110111101111

In the receive mode (i.e., no writes to the SEDDR) the controller typically responds to the TX interrupts and reads the incoming symbols as they become available, performing necessary real-time operations such as ﬁltering messages, computing and verifying CRCs, and issuing IFRs.

Computer Operating Properly (COP) System

Introduction

The Computer Operating Properly (COP) system is comprised of two basic circuit components. One is a free running watchdog timer which, left unattended, generates a periodic MCU reset. The second is a Slow Clock Detect circuit which constantly monitors the OSCIN line for activity. A lack of activity on OSCIN will generate a reset.

Both circuits are capable of generating a COP interrupt which forces an MCU reset and restarts operation at the vector speciﬁed by the contents of location $1FFA, $1FFB. Because the COP interrupt behaves as a reset, the stack pointer is cleared and exiting the COP interrupt software handler must be done via a jump instruction as opposed to an RTI or RTS.

The Watchdog Status Register (WSR, location $1E) contains a ﬂag (Watchdog Flag - WDF, bit 0) which is set whenever a Watchdog Timer overﬂow interrupt occurs. The WDF bit is cleared by a POR or a write to the Watchdog Reset Register (WRR, location $1D) with bit 0 = 0. The WDF can be used to distinguish the type of COP reset (Watchdog timeout vs. Slow Clock Detect) which has occurred.

Following are the details of each of the two circuit.

Slow Clock Detect Circuit

The Slow Clock Detect Circuit consists of a reset-able timer element. The timer is constructed with integrated resistive

and capacitive components. Each positive transition on the OSCIN line reinitializes the timer. In the absence of frequent enough transitions on the input, the timer will eventually reach a preset limit at which point the MCU will be reset via a COP interrupt.

When the frequency has dropped below the preset threshold a COP reset will take place. A COP reset is identical to a POR or

RESET pin reset, except the restart vector is the COP V ector. Follo wing the COP reset the HIP7030A2 is held reset until the start-up timeout of 4064 clocks has been reached. During the 4064 clocks the Slow Clock Detect circuit is inhibited. If at the end of the 4064 clocks the frequency remains below the threshold, a COP reset will immediately take place again.

The primary purpose of this circuit is to force the HIP7030A2 off of the J1850 and SPI busses should the oscillator circuit fail. Due to variability of integrated resistors and capacitors there is a non-critical spread in the timeout speciﬁcation of approximately 10:1. Maximum threshold is 200kHz. Refer to f

SLOW

Electrical Speciﬁcations

for details.

There is no means to disable the Slow Clock Detect. RESET resets the Slow Clock Detect circuit and holds it reset until the start-up timeout of 4064 clocks has been reached and the

RESET pin has gone high.

Watchdog Timer

The Watchdog Timer is a free-running 21 stage counter which divides the OSCIN input by 2,097,152. The Timer is software reset-able, and must be constantly reset before the terminal count is reached. Failure to reset the Watchdog Timer, in due time, results in a forced MCU RESET via a COP interrupt.

765432 10

Watchdog Reset Register

WRR (LOCATION $1D)

Resetting the Watchdog Timer requires two distinct operations. A write of the value $55 to the Watchdog Reset Register (WRR, location $1D) must be followed by a write of the value $AA to the WRR. There is no limit on the time between the writes, other than both must take place before the Watchdog Timer has reached its limit. Typically the two writes are placed in distinct sections of code, which can only be reached by proper ﬂow through the software.

Each time that a write is made to the WRR with bit 0 = 0, the Watchdog Flag in the WSR is cleared. This will happen as a normal side effect of clear the Watchdog Timer via the $55, $AA sequence. The Watchdog ﬂag is also cleared by POR. RESET and Slow Clock Detect do

not affect the WDF. It is set by a Watchdog Timer o verﬂow and can be used to distinguish a Slow Clock Detect reset from the Watchdog reset, both of which share the COP reset vector ($1FFA,$1FFB).

76543210 0000001WDF

WSR (LOCATION $1E)

Page 41

HIP7030A2

Watchdog timeout periods for various OSCIN frequencies are given in Table 10.

There is no mechanism to disable the Watchdog Timer. RESET clears the Watchdog Timer to its initial value.

TABLE 10. WATCHDOG TIMEOUTS FOR COMMON OSCIN

FREQUENCIES

WATCHDOG

TIMEOUT

175ms 12 210ms 10 262ms 8 524ms 4

OSCIN FREQUENCY

(MHz)

Effects of Stop and Wait Modes on the Timer, COP, and Serial Systems

Introduction

The STOP and WAIT instructions have different effects on the programmable timer, VPW Symbol Encoder/Decoder (SENDEC), and serial peripheral interface (SPI) systems. These effects are discussed separately below.

Stop Mode

When the processor executes the STOP instruction, the internal oscillator is turned off. This halts all internal CPU processing including the operation of the programmable timer, serial communications interface, and serial peripheral interface. The only way for the MCU to “wake up” from the STOP mode is by receipt of an external interrupt (logic low on IRQ pin), a negative edge on the detection of a RESET (logic low on on reset). Execution will resume at the instruction immediately following the STOP instruction that caused the HIP7030A2 to enter the STOP mode.

Normally a start-up delay of 4064 t ing from STOP before f etching the ﬁrst instruction. This dela y is intended to guarantee stability of a crystal clock source. If it is known that the clock source will be stable prior to exiting STOP, then the NDEL bit in the SEDCR can be set prior to executing the STOP instruction. Setting NDEL has the effect of shortening the start-up delay to 96 t

The effects of the STOP mode on each of the MCU systems (COP, Timer, SENDEC, and SPI) are described separately in the following sections.

COP During STOP Mode

When the MCU enters the STOP mode, the Watchdog Timer and the Slow Clock Detect circuits are both inhibited.

Timer During STOP Mode

When the MCU enters the STOP mode, the timer counter stops counting (the internal processor is stopped) and remains at that particular count value until the STOP mode is exited by an interrupt (if exited b y RESET the counter is f orced to $FFFC). If the STOP mode is exited by an external low on

VPWIN pin, or by the

RESET pin or a power-

is inserted after exit-

CYC

the

IRQ pin, then the counter resumes from its stopped value as if nothing had happened. Another feature of the programmable timer, in the STOP mode, is that if at least one valid input capture edge occurs at the TCAP pin, the input capture detect circuitry is armed. This action does not set any timer ﬂags or “wake up” the MCU, but when the MCU does “wake up” there will be an active input capture ﬂag (and data) from that ﬁrst valid edge which occurred during the STOP mode. If the STOP mode is exited by an external reset (logic low on RESET pin), then no such input capture ﬂag or data action takes place even if there w as a v alid input capture edge (at the TCAP pin) during the MCU STOP mode.

SENDEC During STOP Mode

When the MCU enters the STOP mode, the absence of any internal clocks causes all SENDEC functions, except Wake Up to cease. If the SENDEC was currently being used to transmit a symbol, that symbol is truncated and the VPWOUT is forced to a low (passive) state. For proper operation, a STOP instruction should not be executed except when the b us is idle .

Normally all transitions are ﬁrst ﬁltered through the SENDECs 3-bit digital ﬁlter. When in ST OP mode the 3-bit ﬁlter is bypassed and any passive to active transition (high to low) on

VPWIN will cause a SENDEC interrupt which will, in turn,

cause the processor to exit the STOP mode. Upon exiting the STOP mode the processor will execute a

SENDEC interrupt. The setting of the TX bit in the SEDSR does

not

bypass the 7µs ﬁlter and as such the TX bit will

not

be set when ﬁrst awakening from STOP. If the NDEL bit has been set prior to entering STOP, software should delay 8µs and check TX. If at that time TX has not been set, the assumption can be made that a noise pulse caused the wakeup and the STOP mode can be reentered. When NDEL is not employed monitoring of TX must continue for several hundred microseconds, as a complete message could have transpired during the oscillator start-up time.

During handling of a SENDEC interrupt following STOP, the SEDSR must be read at least one time to remove the source of the interrupt.

SPI During STOP Mode

When the MCU enters the STOP mode, the baud rate generator which drives the SPI shuts down. This essentially stops all master mode SPI operation. To ensure the SPI bus remains free for transfers, the MSTR bit in the SPCR is cleared, conﬁguring the SPI pins in slave mode. If the STOP instruction is executed during an SPI transfer, in which the HIP7030A2 was the master, that transfer is aborted. If the STOP mode is exited by a RESET , then the appropriate control/status bits are cleared and the SPI is disabled. If the device is in the slave mode when the STOP instruction is executed, the slave SPI will still operate. It can still accept data and clock information in addition to transmitting its own data back to a master device.

At the end of a possible transmission with a slave SPI in the STOP mode, no ﬂags are set until an

IRQ or SENDEC interrupt results in an MCU “wake up”. Caution should be observed when operating the SPI (as a slave) during the STOP mode because none of the protection circuitry (write collision, mode fault, etc.) is active.

Page 42

Wait Mode

When the MCU enters the WAIT mode, the CPU clock is halted. All CPU action is suspended; however, the timer, SENDEC, and SPI systems remain active. In fact an interrupt from the timer, SENDEC, or SPI (in addition to a logic low on the the WAIT mode. Since the three systems mentioned above operate as they do in the normal mode, only a general discussion of the WAIT mode is provided below.

Note that the Slow Clock Detect and Watchdog Timer circuitry continues to function during WAIT. It is requisite upon the designed to ensure that the CPU is removed from WAIT (via an external or TIMER or SENDEC interrupt) frequently enough to prevent a Watchdog Timer overﬂow.

The WAIT mode power consumption depends on how many systems are active. The power consumption will be highest when all the systems (timer, TCMP, SENDEC, and SPI) are active. The power consumption will be the least when the SENDEC and SPI systems are disabled (timer operation cannot be disabled in the WAIT mode). If a non-RESET exit from the WAIT mode is performed (i.e., timer overﬂow interrupt exit), the state of the remaining systems will be unchanged. If a RESET exit from the WAIT mode is performed all the systems revert to the disabled reset state.

IRQ or RESET pins) causes the processor to exit

Instruction Set

The MCU has a set of 62 basic instructions. They can be divided into ﬁve different types: register/memory, read-modify-write, branch, bit manipulation, and control. The following paragraphs brieﬂy explain each type. All the instructions within a given type are presented in individual tables.

Most of these instructions use two operands. The ﬁrst operand is either the accumulator or the index register. The second operand is obtained from memory using one of the addressing modes. The operand for the jump unconditional (JMP) and jump to subroutine (JSR) instructions is the program counter. Refer to Table 11.

Read-Modify-Write Instructions

These instructions read a memory location or a register, modify or test its contents, and write the modiﬁed value back to memory or to the register. The test for negative or zero (TST) instruction is an exception to the read-modify-write sequence since it does not modify the value. Refer to Table 12.

Page 43

FUNCTION MNEM

Load A from Memory

Load X from Memory

Store A in Memory

Store X in Memory

Add Memory to A

Add Memory and Carry to A

Subtract Memory

Subtract Memory From A with Borrow

AND Memory to A

OR Memory with A

Exclusive OR Memory with A

Arithmetic Compare A with Memory

Arithmetic Compare X with Memory

Bit Test Memory with A (Logical Compare)

Jump Unconditional

Jump to Subroutine

TABLE 11. REGISTER/MEMORY INSTRUCTIONS

ADDRESSING MODES

INDEXED

IMMEDIATE DIRECT EXTENDED

CODE

LDA A6 2 2 B6 2 3 C6 3 4 F6 1 3 E6 2 4 D6 3 5

LDX AE 2 2 BE 2 3 CE 3 4 FE 1 3 EE 2 4 DE 3 5

STA- - - B7 2 4C73 5 F7 1 4E72 5D73 6

STX- - - BF2 4CF3 5 FF 1 4EF2 5DF3 6

ADD AB 2 2 BB 2 3 CB 3 4 FB 1 3 EB 2 4 DB 3 5

ADC A9 2 2 B9 2 3 C9 3 4 F9 1 3 E9 2 4 D9 3 5

SUB A0 2 2 B0 2 3 C0 3 4 F0 1 3 E0 2 4 D0 3 5

SBC A2 2 2 B2 2 3 C2 3 4 F2 1 3 E2 2 4 D2 3 5

AND A4 2 2 B4 2 3 C4 3 4 F4 1 3 E4 2 4 D4 3 5

ORA AA 2 2 BA 2 3 CA 3 4 FA 1 3 EA 2 4 DA 3 5

EOR A8 2 2 B8 2 3 C8 3 4 F8 1 3 E8 2 4 D8 3 5

CMP A1 2 2 B1 2 3 C1 3 4 F1 1 3 E1 2 4 D1 3 5

CPX A3 2 2 B3 2 3 C3 3 4 F3 1 3 E3 2 4 D3 3 5

BIT A5 2 2 B5 2 3 C5 3 4 F5 1 3 E5 2 4 D5 3 5

JMP- - -BC2 2CC3 3FC1 2EC2 3DC3 4

JSR- - -BD2 2CD3 3FD1 5ED2 6DD3 7

NO.

BYTES

NO.

CYCLESOPCODE

NO.

BYTES

NO.

CYCLESOPCODE

NO.

BYTES

NO.

CYCLESOPCODE

(NO OFFSET)

NO.

BYTES

CYCLESOPCODE

NO.

INDEXED

(8-BIT OFFSET)

NO.

BYTES

CYCLESOPCODE

NO.

INDEXED

(16-BIT OFFSET)

NO.

BYTES

NO.

CYCLES

HIP7030A2

Page 44

TABLE 12. READ-MODIFY-WRITE INSTRUCTIONS

ADDRESSING MODES

INDEXED

INHERENT (A) INHERENT (X) DIRECT

FUNCTION MNEM

Increment INC 4C 1 3 5C 1 3 3C 2 5 7C 1 5 6C 2 6 Decrement DEC 4A 1 3 5A 1 3 3A 2 5 7A 1 5 6A 2 6 Clear CLR 4F 1 3 5F 1 3 3F 2 5 7F 1 5 6F 2 6 Complement COM 43 1 3 53 1 3 33 2 5 73 1 5 63 2 6 Negate

(2’s Complement) Rotate Left Thru

Carry Rotate Right Thru

Carry Logical Shift Left LSL 48 1 3 58 1 3 38 2 5 78 1 5 68 2 6 Logical Shift Right LSR 44 1 3 54 1 3 34 2 5 74 1 5 64 2 6 Arithmetic

Shift Right Test for Negative or

Zero Multiply MUL 42 1 11 - - - - - - - - - - - -

NEG 40 1 3 50 1 3 30 2 5 70 1 5 60 2 6

ROL 49 1 3 59 1 3 39 2 5 79 1 5 69 2 6

ROR 46 1 3 56 1 3 36 2 5 76 1 5 66 2 6

ASR 47 1 3 57 1 3 37 2 5 77 1 5 67 2 6

TST 4D 1 3 5D 1 3 3D 2 4 7D 1 4 6D 2 5

CODE

NO.

BYTES

NO.

CYCLESOPCODE

NO.

BYTES

NO.

CYCLESOPCODE

NO.

BYTES

NO.

CYCLESOPCODE

(NO OFFSET)

NO.

BYTES

NO.

CYCLESOPCODE

INDEXED

(8-BIT OFFSET)

NO.

BYTES

CYCLES

NO.

HIP7030A2

Page 45

HIP7030A2

Branch Instructions

Most branch instructions test the state of the condition code register and if certain criteria are met, a branch is executed. This adds an offset between -127 and +128 to the current program counter. Refer to Table 13.

TABLE 13. BRANCH INSTRUCTIONS

RELATIVE ADDRESSING

MODE

FUNCTION MNEM

Branch Always BRA 20 2 3 Branch Never BRN 21 2 3 Branch IFF Higher BHI 22 2 3 Branch IFF Lower or

Same Branch IFF Carry

Clear (Branch IFF Higher or

Same) Branch IFF Carry Set BCS 25 2 3

BLS 23 2 3

BCC 24 2 3

(BHS) 24 2 3

CODE

NO.

BYTES

NO.

CYCLES

bytes (page zero). An additional feature allows the software to test and branch on the state of any bit within the ﬁrst 256 locations. The bit set, bit clear, and bit test and branch functions are all implemented with a single instruction. For the test and branch instructions, the value of the bit tested is automatically placed in the carry bit of the condition code register. Refer to Table 14.

TABLE 14A. BIT SET/CLEAR INSTRUCTIONS

FUNCTION MNEM

Set Bit n BSET

n (n = 0 . . .7)

Clear Bit n BCLR

n (n = 0 . . .7)

TABLE 14B. BIT TEST AND BRANCH INSTRUCTIONS

FUNCTION MNEM

Branch IFF Bit n is Set

Branch IFF Bit n is Clear

BRSET n (n = 0 . . . 7)

BRCLR n (n = 0 . . . 7)

CODE

10 + 2•n 2 5

11 + 2•n 2 5

CODE

2•n 3 5

01 + 2•n 3 5

NO.

BYTES

NO.

BYTES

NO.

CYCLES

NO.

CYCLES

(Branch IFF Lower) (BLO) 25 2 3 Branch IFF Not Equal BNE 26 2 3 Branch IFF Equal BEQ 27 2 3 Branch IFF Half Carry

Clear Branch IFF Half Carry

Set Branch IFF Plus BPL 2A 2 3 Branch IFF Minus BMI 2B 2 3 Branch IFF Interrupt

Mask Bit is Clear Branch IFF Interrupt

Mask Bit is Set Branch IFF Interrupt

Line is Low Branch IFF Interrupt

Line is High Branch to Subroutine BSR AD 2 6

BHCC 28 2 3

BHCS 29 2 3

BMC 2C 2 3

BMS 2D 2 3

BIL 2E 2 3

BIH 2F 2 3

Bit Manipulation Instructions

The MCU is capable of setting or clearing any bit which resides in the ﬁrst 256 bytes of the memory space except for ROM, port D data location ($03), serial peripheral status register ($0B), serial communications status register (10), timer status register ($13), and timer input capture register ($14 $15). All port registers, port DDRs, timer, two serial systems, on-chip RAM, and 48 bytes of ROM reside in the ﬁrst 256

Control Instructions

These instructions are register reference instructions and are used to control processor operation during program execution. Refer to Table 15.

TABLE 15. CONTROL INSTRUCTIONS

INHERENT

FUNCTION MNEM

Transfer A to X TAX 97 1 2 Transfer X to A TXA 9F 1 2 Set Carry Bit SEC 99 1 2 Clear Carry Bit CLC 98 1 2 Set Interrupt Mask Bit SEI 9B 1 2 Clear Interrupt Mask

Bit Software Interrupt SWI 83 1 10 Return from Subroutine RTS 81 1 6 Return from Interrupt RTI 80 1 9 Reset Stack Pointer RSP 9C 1 2 No-Operation NOP 9D 1 2 Stop STOP 8E 1 2 Wait WAIT 8F 1 2

CLI 9A 1 2

CODE

NO.

BYTES

NO.

CYCLES

Page 46

HIP7030A2

Alphabetical Listing

The complete instruction set is given in alphabetical order in Table 16.

Opcode Map

Table 17 is an opcode map for the instructions used on the MCU.

Addressing Modes

The MCU uses ten different addressing modes to provide the programmer with an opportunity to optimize the code to all situations. The various indexed addressing modes make it possible to locate data tables, code conversion tables, and scaling tables anywhere in the memory space. Short indexed accesses are single byte instructions, while the longest instructions (three bytes) permit accessing tables throughout memory. Short absolute (direct) and long absolute (extended) addressing are also included. One and two byte direct addressing instructions access all data bytes in most applications. Extended addressing permits jump instructions to reach all memory. Table 17 shows the addressing modes for each instruction, with the effects each instruction has on the condition code register.

The term “effective address” (EA) is used in describing the various addressing modes, and is deﬁned as the byte address to or from which the argument for an instruction is fetched or stored. The ten addressing modes of the processor are described below. Parentheses are used to indicate “contents of” the location or register referred to; e.g., (PC) indicates the contents of the location pointed to by the PC. An arrow indicates “is replaced by”, and a colon indicates concatenation of two bytes.

Inherent

In inherent instructions, all the information necessary to execute the instruction is contained in the opcode. Operations specifying only the index register or accumulator, and no other arguments, are included in this mode.

Immediate

In immediate addressing, the operand is contained in the byte immediately following the opcode. Immediate addressing is used to access constants which do not change during program execution (e.g., a constant used to initialize a loop counter).

EA = PC + 1; PC ← PC + 2

Direct

In the direct addressing mode, the effective address of the argument is contained in a single byte following the opcode byte. Direct addressing allows the user to directly address the lowest 256 bytes in memory with a single two byte instruction. This includes most on-chip RAM and all I/O registers. Direct addressing is efﬁcient in both memory and time.

EA = (PC +1); PC ← PC + 2 Address Bus High 0; Address Bus Low ← (PC + 1)

Extended

In the extended addressing mode, the effective address of the argument is contained in the two bytes following the opcode. Instructions with extended addressing modes are capable of referencing arguments anywhere in memory with a single three-byte instruction.

EA = (PC + 1) : (PC + 2); PC ← PC + 3 Address Bus High ← (PC + 1); Address Bus Low ← (PC + 2)

Indexed, No Offset

In the indexed, no offset addressing mode, the effective address of the argument is contained in the 8-bit index register. Thus, this addressing mode can access the ﬁrst 256 memory locations. These instructions are only one byte long. This mode is used to move a pointer through a table or to address a frequently referenced RAM or I/O location.

EA = X; PC ← PC + 1 Address Bus High ← 0; Address Bus Low ← X

Indexed, 8-Bit Offset

Here the EA is obtained by adding the contents of the byte following the opcode to that of the index register; therefore, the operand is located anywhere within the lowest 511 memory locations. For example, this mode of addressing is useful for selecting the mth element in a n element table. All instructions are two bytes. The content of the index register (S) is not changed. The content of (PC + 1) is an unsigned 8-bit integer. One byte offset indexing permits look-up tables to be easily accessed in either RAM or ROM.

EA = X + (PC + 1); PC ← PC + 2 Address Bus High ← K; Address Bus Low ← X + (PC + 1) where: K = the carry from the addition of x + (PC + 1).

Indexed, 16-Bit Offset

In the indexed, 16-bit offset addressing mode, the effective address is the sum of the contents of the unsigned 8-bit index register and the two unsigned bytes following the opcode. This addressing mode can be used in a manner similar to indexed 8-bit offset, except that this three byte instruction allows tables to be anywhere in memory (e.g., jump tables in ROM). The content of the index register is not changed.

EA = X + [(PC + 1) : (PC + 2)]; PC ← PC + 3 Address Bus High ← (PC + 1) + K Address Bus Low ← X + (PC + 2) where: K = The carry from the addition of X + (PC + 2).

Relative

Relative addressing is only used in branch instructions. In relative addressing, the content of the 8-bit signed byte following the opcode (the offset) is added to the PC if and only if the branch condition is true. Otherwise, control proceeds to the next instruction. The span of relative addressing is limited to the range of -126 to +129 bytes from the branch instruction opcode location.

EA = PC + 2 + (PC + 1); PC ← EA if branch taken; otherwise, EA = PC ← PC + 2.

Page 47

Bit Set/Clear

HIP7030A2

Direct addressing and bit addressing are combined in instructions which set and clear individual memory and I/O bits. In the bit set and clear instructions, the byte is speciﬁed as a direct address in the location following the opcode. The ﬁrst 256 addressable locations are thus, accessed. The bit to be modiﬁed within that byte is speciﬁed in the ﬁrst three bits of the opcode. The bit set and clear instructions occupy two bytes, one for the opcode (including the bit number) and the other to address the byte which contains the bit of interest.

EA = (PC + 1); PC ← PC + 2 Address Bus High ← 0; Address Bus Low ← (PC + 1).

Bit Test and Branch

Bit test and branch is a combination of direct addressing, bit set/clear addressing, and relative addressing. The actual bit to be tested, within the byte, is speciﬁed within the low order nibble of the opcode. The address of the data byte to be tested is located via a direct address in the location following the opcode byte (EA1). The signed relative 8-bit offset is in the third byte (EA2) and is added to the PC if the speciﬁed bit is set or cleared in the speciﬁed memory location. This single three byte instruction allows the program to branch based on the condition of any bit in the ﬁrst 256 locations of memory .

EA1 = (PC +1) Address Bus High Q 0; Address Bus Low ← (PC + 1) EA2 = PC + 3 + (PC + 2); PC ← EA2 if branch taken;

otherwise, PC ← PC + 3.

Power Considerations

The average chip-junction temperature, TJ, inoC can be obtained from:

= TA + (PD•θJA) (EQ. 1)

Where: T

INT

I/O

For most applications P An approximate relationship between P

neglected) is:

Solving equations 1 and 2 for K gives:

K = P

Where K is a constant pertaining to the particular part. K can be determined from Equation 3 by measuring P rium) for a know T and TJcan be obtained by solving Equation 1 and Equation 2 iteratively for any value of T

= Ambient Temperature,oC

= Package Thermal Resistance

Junction-to-Ambient,

= P

INT

+ P

I/O

C/W

= ICC•VCC, Watts - Chip Internal Power

= Power Dissipation on Input and Output

Pins - User Determined

< P

I/O

and can be neglected.

INT

and TJ (if P

= K / (TJ + 273oC) (EQ. 2)

•(TA + 273oC) + θJA•P

. Using this value of K, the values of P

(EQ. 3)

(at equilib-

I/O

TEST

POINT

EQUIVALENT TEST LOAD (SEE TABLE FOR VALUES OF R1 AND R2)

PINS R

VDD = 4.5V PA0 - PA7, PD0 - PD4

MISO, MOSI, SCK 1.9kΩ 2.2kΩ 200pF

3.26kΩ 2.38kΩ 50pF

Page 48

HIP7030A2

TABLE 16. INSTRUCTION SET

CONDITION

ADDRESSING MODES

BIT

INDEXED

(NO

MNEM

BHCC X • • • • • BHCS X • • • • •

BRCLR X ••••Λ BRSET X ••••Λ

INHERENT IMMEDIATE DIRECT EXTENDED RELATIVE

ADC X X X X X X Λ • ΛΛΛ ADD X X X X X X Λ • ΛΛΛ AND X X X X X X • • Λ • Λ

ASL X X X X • • ΛΛΛ ASR X X X X • • ΛΛΛ BCC X •••••

BCLR X •••••

BCS X ••••• BEQ X •••••

BHI X •••••

BHS X •••••

BIH X •••••

BIL X •••••

BIT X X X X X X • • ΛΛ • BLO X ••••• BLS X •••••

BMC X •••••

BMI X •••••

BMS X ••••• BNE X •••••

BPL X •••••

BRA X ••••• BRN X •••••

BSET X •••••

BSR X •••••

CLC X ••••0

CLI X •0••• CLR X X X X • • 0 1 •

CMP X X X X X X • • ΛΛΛ COM X X X X • • ΛΛ1 CPX X X X X X X • • ΛΛ DEC X X X X • • ΛΛ•

OFFSET)

INDEXED

(8 BITS)

INDEXED

(16 BITS)

BIT

SET/CLE

TEST

AND

BRANCH H I N Z C

CODES

Page 49

HIP7030A2

TABLE 16. INSTRUCTION SET (Continued)

CONDITION

ADDRESSING MODES

BIT

INDEXED

(NO

MNEM

Condition Code Symbols:

INHERENT IMMEDIATE DIRECT EXTENDED RELATIVE

EOR X X X X X X • • ΛΛ •

INC X X ••ΛΛ • JMP X X X X X ••••• JSR X X X X X ••••• LDA X X X X X X • • ΛΛ• LDX X X X X X X • • ΛΛ•

LSL X X X X • • ΛΛΛ LSR X X X X • • 0 ΛΛ

MUL X 0•••0 NEG X X X X • • ΛΛΛ NOP X ••••• ORA X X X X X X • • ΛΛ • ROL X X X X • • ΛΛΛ ROR X X X X • • ΛΛΛ RSP X •••••

RTI X ????? RTS X •••••

SBC X X X X X X • • ΛΛΛ SEC X ••••1

SEI X •1••• STA X X X X X • • ΛΛ •

STOP X •0•••

STX X X X X X • • ΛΛ •

SUB X X X X X X • • ΛΛΛ

SWI X •1••• TAX X ••••• TST X X X X • • ΛΛ• TXA X •••••

WAIT X •0•••

H = Half Carry (from Bit 3) Λ = Test and Set if True Cleared Otherwise I = Interrupt Mask • = Not Affected N = Negate (Sign Bit) ? = Load CC Register From Stack Z = Zero 0 = Cleared C = Carry/Borrow 1 = Set

OFFSET)

INDEXED

(8 BITS)

INDEXED

(16 BITS)

BIT

SET/CLE

TEST

AND

BRANCH H I N Z C

CODES

Bit 7 6543210

Page 50

TABLE 17. INSTRUCTION SET OPCODE MAP

LOW

MANIPULATION

BRSET0

3 BTB

BRCLR0

3 BTB

BRSET1

3 BTB

BRCLR1

3 BTB

BRSET2

3 BTB

BRCLR2

3 BTB

BRSET3

3 BTB

BRCLR3

3 BTB

BRSET4

3 BTB

BRCLR4

3 BTB

BRSET5

3 BTB

BRCLR5

3 BTB

BRSET6

3 BTB

BIT

BRANC

H READ/MODIFY/WRITE CONTROL REGISTER/MEMORY

BTB BSC REL DIR INH INH IX1 IX INH INH IMM DIR EXT IX2 IX1 IX

0123456789ABCDEF

BSET0

2 BSC

BCLR0

2 BSC

BSET1

2 BSC

BCLR1

2 BSC

BSET2

2 BSC

BCLR2

2 BSC

BSET3

2 BSC

BCLR3

2 BSC

BSET4

2 BSC

BCLR4

2 BSC

BSET5

2 BSC

BCLR5

2 BSC

BSET6

2 BSC

2 REL

BRA

BRN

BHI

BLS

BCC

BCS

BNE

BEQ

BHCC

BHCS

BPL

BMI

BMC

NEG

2 DIR

COM

2 DIR

LSR

2 DIR

ROR

2 DIR

ASR

2 DIR

LSL

2 DIR

ROL

2 DIR

DEC

2 DIR

INC

2 DIR

NEGA

1 INH

MUL

1 INH

COMA

1 INH

LSRA

1 INH

RORA

1 INH

ASRA

1 INH

LSLA

1 INH

ROLA

1 INH

DECA

1 INH

INCA

1 INH

NEGX

COMX

LSRX

RORX

ASRX

LSLX

ROLX

DECX

INCX

2 IX1

NEG

COM

LSR

ROR

ASR

LSL

ROL

DEC

INC

1IX

NEG

COM

1 INH

LSR

1IX

ROR

1IX

ASR

LSL

ROL

DEC

INC

RTI

RTS

SWI

1 INH

TAX

CLC

SEC

CLI

SEI

RSP

SUB

2 IMM

CMP

2 IMM

SBC

2 IMM

CPX

2 IMM

AND

2 IMM

LDA

2 IMM

EOR

2 IMM

ADC

2 IMM

ORA

2 IMM

ADD

2 IMM

BIT

SUB

2 DIR

CMP

2 DIR

SBC

2 DIR

CPX

2 DIR

AND

2 DIR

BIT

2 DIR

LDA

2 DIR

STA

2 DIR

EOR

2 DIR

ADC

2 DIR

ORA

2 DIR

ADD

2 DIR

JMP

2 DIR

SUB

3 EXT

CMP

3 EXT

SBC

3 EXT

CPX

3 EXT

AND

3 EXT

BIT

3 EXT

LDA

3 EXT

STA

3 EXT

EOR

3 EXT

ADC

3 EXT

ORA

3 EXT

ADD

3 EXT

JMP

3 EXT

SUB

3 IX2

CMP

3 IX2

SBC

3 IX2

CPX

3 IX2

AND

3 IX2

BIT

3 IX2

LDA

3 IX2

STA

3 IX2

EOR

3 IX2

ADC

3 IX2

ORA

3 IX2

ADD

3 IX2

JMP

3 IX2

SUB

2 IX1

CMP

2 IX1

SBC

2 IX1

CPX

2 IX1

AND

2 IX1

BIT

2 IX1

LDA

2 IX1

STA

2 IX1

EOR

2 IX1

ADC

2 IX1

ORA

2 IX1

ADD

2 IX1

JMP

2 IX1

1IX

1 IX

1IX

1 IX

SUB

CMP

SBC

CPX

AND

BIT

LDA

STA

EOR

ADC

ORA

ADD

JMP

LOW

HIP7030A2

Page 51

TABLE 17. INSTRUCTION SET OPCODE MAP (Continued)

LOW

MANIPULATION

BTB BSC REL DIR INH INH IX1 IX INH INH IMM DIR EXT IX2 IX1 IX

BRCLR6

3 BTB

BRSET7

3 BTB

BRCLR7

3 BTB

INH = Inherent IMM = Immediate DIR = Direct EXT = Extended

BIT

BRANC

H READ/MODIFY/WRITE CONTROL REGISTER/MEMORY

JSR

LDX

STX

0123456789ABCDEF

BCLR6

2 BSC

BSET7

2 BSC

BCLR7

2 BSC

2 REL

BMS

BIL

BIH

TST

2 DIR

CLR

2 DIR

REL = Relative BSC = Bit Set/Clear BTB = Bit Test and Branch BTB = Bit Test and Branch

TSTA

1 INH

CLRA

1 INH

TSTX

1 INH

CLRX

1 INH

2 IX1

TST

CLR

TST

1IX

1 INH

CLR

1 IX

1 INH

IX = Indexed, No Offset IX1 = Indexed, 8-Bit Offset IX2 = Indexed, 16-Bit Offset

STOP

WAIT

NOP

1 INH

TXA

1 INH

BSR

2 REL

LDX

2 IMM

JSR

2 DIR

LDX

2 DIR

STX

2 DIR

LSB of Opcode

JSR

3 EXT

LDX

3 EXT

STX

3 EXT

LOW

3 IX2

3 BTB

JSR

LDX

STX

BRSET0

2 IX1

JSR

LDX

STX

1 IX

MSB of Opcode

Number of Cycles

Instruction Mnemonic

Number of Bytes/Addressing Mode

LOW

HIP7030A2

Page 52

HIP7030A2

$0000 I/O I/O I/O I/O I/O I/O I/O I/O PORT A

8 9 10 11 12 13 14 15 Pin Numbers

PA7 PA6 PA5 PA4 PA3 PA2 PA1 PA0 Pin Name

$0001 UNUSED $0002 UNUSED

$0003 CMP3 CMP2 0 I/O I/O I/O I/O I/O PORT D

18 19 - 17 18 19 20 21 Pin Numbers

V3>VREF V2>VREF - PD4/VREF PD3/V2 PD2/V1 PD1 PD0 Pin Name

$0004 I/O I/O I/O I/O I/O I/O I/O I/O DDRA $0005 UNUSED $0006 UNUSED

$0007 0 0 0 I/O I/O I/O I/O I/O DDRD $0008 0 0 CMPE 0 0 0 STE1 STE0 SFRD $0009 $000A SPIE SPE - MSTR CPOL CPHA SPR1 SPR0 SPCR $000B SPIF WCOL 0 MODF 0000SPSR $000C SPI DATA REGISTER SPDR $000D UNUSED $000E UNUSED $000F TXIE - - NDEL - 4X PRE1 PRE0 SEDCR $0010 TX BRK NEW NOIZ OVR TALK NECHO 0 SEDSR $0011 FSOF S2 S1 S0 LEV R2 R1 R0 SEDDR $0012 ICIE OCIE TOIE 0 0 0 IEDG OLVL TCR $0013 ICF OCF TOF 00000TSR $0014 Bit 15 Bit 8 CAPHI $0015 Bit 7 Bit 0 CAPLO $0016 Bit 15 Bit 8 CMPHI $0017 Bit 7 Bit 0 CMPLO $0018 Bit 15 Bit 8 CNTHI $0019 Bit 7 Bit 0 CNTLO

UNUSED

$001A Bit 15 Bit 8 ALTHI $001B Bit 7 Bit 0 ALTLO $001C UNUSED $001D $55/$AA WRR $001E 0000001WDFWSR $001F RESERVED RESERVED

I/O, CONTROL, STATUS, AND DATA REGISTER DEFINITIONS

Ordering Information Sheet

Page 53

HIP7030A2

A. Package Type (select one):

28 Ld Dual-In-Line Plastic (E) 28 Ld SO (M)

B. Choose from the following microcomputer option. A manufacturing mask will be generated from this information.

Refer to data sheet or data book instructions for submitting data for ROM patterns.

OSCB - Buffered Oscillator Output (select one)

Enabled Disabled

C. Customer Company ____________________________________________________________________________

Address _____________________________________________________________________________________ City _________________________________________________________________________________________ Phone ( ____ ) ___________________________________________ Extension ________________________ Contact Person _______________________________________________________________________________ Customer Part Number _________________________________________________________________________

D. Pattern Media (S-Record Formatted File Should Be Used - Unspecified locations are filled with 0’s)

Floppy Disk: 3

/2”5

/4” MODEM Upload: S-Record Filename _________________ Medium if other than above † _____________________________________________________________________ Signature _________________________________________________ Title ______________________________

† The HIP7030A2 requires 8K of data

Date _____________________________

Page 54

HIP7030A2

ROM Ordering Instructions

The HIP7030A2 family of microcontrollers contains mask programmed ROMs. The contents of these ROMs are personalized to meet a customer’s code requirements during manufacturing of the ICs. The code is programmed via photomasking techniques. Semiconductor manufacturing is a batch process, and all microcontrollers manufactured in a given lot (a batch) will contain identical ROM code.

Intersil generates a customer’s ROM mask from an ASCII representation of the desired ROM contents together with other speciﬁc information. The preceding page contains a sheet which can be used to provide the required information when ordering a masked ROM microcontroller.

Data Format Options

The ROM data can be submitted in various formats. The following list summarizes the principal formats which Intersil will accept. The list is in order of preference, with S-Record formatted data ﬁles being the preferred format.

• S-Record Formatted Hex Data File via modem upload

• S-Record Formatted Hex Data File via e-mail

• S-Record Formatted Hex Data File on ﬂoppy disk

• 6805 Assembly Language Source File on ﬂoppy disk

• Contents of a 27XX type EPROM/EEPROM

Procedure for Submitting Data

When submitting data via a physical medium such as a ﬂoppy disk or EPROM, the “Ordering Information Sheet” on the preceding page must be completed and submitted with the data.

When utilizing the Intersil Customer Pattern Retrieval System (modem upload) the customer will be prompted for the same information as that speciﬁed on the “Ordering Information Sheet”.

If the data is submitted via e-mail, the message should include the same information as that speciﬁed on the “Ordering Information Sheet”.

Intersil Customer Pattern Retrieval System

To access the Intersil Customer Pattern Retrieval System, you must ﬁrst obtain an account ID and password from your Intersil sales representative. The system is accessed by dialing 1-908-685-6541. It is presently set to run with baud rates up to 2400 baud, with 8 data bits, 1 stop bit, and no parity bit. The data transfer is done using text mode Kermit transfers.

Check the Intersil Corporate Internet Site, http://www.intersil.com, for the latest information on the Intersil Customer Pattern Retrieval System.

Regardless of the medium used to transfer the data, contents of all of the User ROM regions of the memory map of the particular microcontroller should be speciﬁed. This includes any Page 0 User ROM and User Reset/Interrupt Vectors. Data should not be speciﬁed for the Self Check ROM space of a device. All unused locations should either not be speciﬁed (S-Record and source ﬁles) or speciﬁed as $00 (EPROM/EEPROM). Any unspeciﬁed locations will be ﬁlled with $00 by Intersil.

Page 55

Small Outline Plastic Packages (SOIC)

HIP7030A2

INDEX AREA

123

-A-

0.25(0.010) B

-B-

SEATING PLANE

-C-

h x 45

0.25(0.010) C AMB

NOTES:

1. Symbols are deﬁned in the “MO Series Symbol List” in Section

2.2 of Publication Number 95.

2. Dimensioning and tolerancing per ANSI Y14.5M-1982.

3. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed

0.15mm (0.006 inch) per side.

4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per side.

5. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area.

6. “L” is the length of terminal for soldering to a substrate.

7. “N” is the number of terminal positions.

8. Terminal numbers are shown for reference only.

9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater above the seating plane, shall not exceed a maximum value of

0.61mm (0.024 inch)

10. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact.

0.10(0.004)

M28.3 (JEDEC MS-013-AE ISSUE C)

28 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE

INCHES MILLIMETERS

SYMBOL

A 0.0926 0.1043 2.35 2.65 -

A1 0.0040 0.0118 0.10 0.30 -

B 0.013 0.0200 0.33 0.51 9 C 0.0091 0.0125 0.23 0.32 D 0.6969 0.7125 17.70 18.10 3

E 0.2914 0.2992 7.40 7.60 4

e 0.05 BSC 1.27 BSC H 0.394 0.419 10.00 10.65 -

h 0.01 0.029 0.25 0.75 5

L 0.016 0.050 0.40 1.27 6 N28 287

Rev. 0 12/93

NOTESMIN MAX MIN MAX

Page 56

Dual-In-Line Plastic Packages (PDIP)

HIP7030A2

-C-

-B-

INDEX

AREA

BASE

PLANE

SEATING

PLANE

D1 B1

1 2 3 N/2

-AD

0.010 (0.25) C AMB

NOTES:

1. Controlling Dimensions: INCH. In case of conﬂict between English and Metric dimensions, the inch dimensions control.

2. Dimensioning and tolerancing per ANSI Y14.5M-1982.

3. Symbols are defined in the “MO Series Symbol List” in Section

2.2 of Publication No. 95.

4. Dimensions A, A1 and L are measured with the package seated in JEDEC seating plane gauge GS-3.

5. D, D1, and E1 dimensions do not include mold flash or protrusions. Mold flash or protrusions shall not exceed 0.010 inch (0.25mm).

6. E and are measured with the leads constrained to be per-

pendicular to datum .

-C-

7. eB and eC are measured at the lead tips with the leads unconstrained. eC must be zero or greater.

8. B1 maximum dimensions do not include dambar protrusions. Dambar protrusions shall not exceed 0.010 inch (0.25mm).

9. N is the maximum number of terminal positions.

10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm).

E28.6 (JEDEC MS-011-AB ISSUE B)

28 LEAD DUAL-IN-LINE PLASTIC PACKAGE

INCHES MILLIMETERS

SYMBOL

A - 0.250 - 6.35 4

A1 0.015 - 0.39 - 4 A2 0.125 0.195 3.18 4.95 -

B 0.014 0.022 0.356 0.558 -

B1 0.030 0.070 0.77 1.77 8

C 0.008 0.015 0.204 0.381 D 1.380 1.565 35.1 39.7 5

D1 0.005 - 0.13 - 5

E 0.600 0.625 15.24 15.87 6

E1 0.485 0.580 12.32 14.73 5

e 0.100 BSC 2.54 BSC -

0.600 BSC 15.24 BSC 6

- 0.700 - 17.78 7

L 0.115 0.200 2.93 5.08 4

N28 289

NOTESMIN MAX MIN MAX

Rev. 0 12/93

All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certiﬁcation.

Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or speciﬁcations at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under an y patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see web site http://www.intersil.com

Sales Ofﬁce Headquarters

NORTH AMERICA

Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (407) 724-7000 FAX: (407) 724-7240

EUROPE

Intersil SA Mercure Center 100, Rue de la Fusee 1130 Brussels, Belgium TEL: (32) 2.724.2111 FAX: (32) 2.724.22.05

ASIA

Intersil (Taiwan) Ltd. Taiwan Limited 7F-6, No. 101 Fu Hsing North Road Taipei, Taiwan Republic of China TEL: (886) 2 2716 9310 FAX: (886) 2 2715 3029

Datasheet HIP7030A2 Datasheet (Intersil Corporation)

Specifications and Main Features

Frequently Asked Questions

User Manual