Page 1
HD74LVU04A
Hex Inverters
ADE-205-248 (Z)
1st Edition
March 1999
Description
The HD74LVU04A has six inverters with unbuffered outputs in a 14-pin package.
Low-voltage and high-speed operation is suitable for the battery-powered products (e.g., notebook
computers), and the low-power consumption extends the battery life.
Features
• VCC = 2.0 V to 5.5 V operation
• All inputs VIH (Max.) = 5.5 V (@VCC = 0 V to 5.5 V)
• All outputs VO (Max.) = 5.5 V (@VCC = 0 V)
• Typical VOL ground bounce < 0.8 V (@VCC = 3.3 V, Ta = 25°C)
• Typical VOH undershoot > 2.3 V (@VCC = 3.3 V, Ta = 25°C)
• Output current ±6 mA (@VCC = 3.0 V to 3.6 V), ±12 mA (@VCC = 4.5 V to 5.5 V)
Function Table
Input A Output Y
HL
LH
Note: H: High level
L: Low level
Page 2
HD74LVU04A
Pin Arrangement
1A
1Y
2A
2Y
3A
3Y
GND
1
2
3
4
5
6
7
(Top view)
14
13
12
11
10
V
CC
6A
6Y
5A
5Y
4A
9
4Y
8
2
Page 3
HD74LVU04A
Absolute Maximum Ratings
Item Symbol Ratings Unit Conditions
Supply voltage range V
Input voltage range*
Output voltage range*
1
1, 2
Input clamp current I
Output clamp current I
Continuous output current I
Continuous current through
V
or GND
CC
Maximum power dissipation
at Ta = 25°C (in still air)*
3
CC
V
I
V
O
IK
OK
O
or I
I
CC
GND
P
T
Storage temperature Tstg –65 to 150 °C
Notes: The absolute maximum ratings are values which must not individually be exceeded, and furthermore,
no two of which may be realized at the same time.
1. The input and output voltage ratings may be exceeded if the input and output clamp-current
ratings are observed.
2. This value is limited to 5.5 V maximum.
3. The maximum package power dissipation was calculated using a junction temperature of 150°C.
–0.5 to 7.0 V
–0.5 to 7.0 V
–0.5 to VCC + 0.5 V Output: H or L
–20 mA VI < 0
±50 mA VO < 0 or VO > V
±25 mA VO = 0 to V
CC
±50 mA
785 mW SOP
500 TSSOP
CC
3
Page 4
HD74LVU04A
Recommended Operating Conditions
Item Symbol Min Max Unit Conditions
Supply voltage range V
Input voltage range V
Output voltage range V
Output current I
CC
I
O
OH
I
OL
Operating free-air temperature Ta –40 85 °C
Note: Unused or floating inputs must be held high or low.
2.0 5.5 V
0 5.5 V
0VCCV
— –50 µAV
—–2 mAV
—–6 V
= 2.0 V
CC
= 2.3 to 2.7 V
CC
= 3.0 to 3.6 V
CC
— –12 VCC = 4.5 to 5.5 V
—50 µAV
= 2.0 V
CC
— 2 mA VCC = 2.3 to 2.7 V
—6 V
—12 V
= 3.0 to 3.6 V
CC
= 4.5 to 5.5 V
CC
Logic Diagram
A
Y
4
Page 5
HD74LVU04A
DC Electrical Characteristics
• Ta = –40 to 85°C
Item Symbol VCC (V)* Min Typ Max Unit Test Conditions
Input voltage V
Output voltage V
Input current I
Quiescent
IH
V
IL
OH
V
OL
IN
I
CC
supply current
Input
C
IN
capacitance
Note: For conditions shown as Min or Max, use the appropriate values under recommended operating
conditions.
2.0 1.7 — — V
2.3 to 2.7 VCC × 0.8 — —
3.0 to 3.6 VCC × 0.8 — —
4.5 to 5.5 VCC × 0.8 — —
2.0 — — 0.3
2.3 to 2.7 — — VCC × 0.2
3.0 to 3.6 — — VCC × 0.2
4.5 to 5.5 — — VCC × 0.2
Min to
VCC – 0.1 — — V IOL = –50 µA
Max
2.3 2.0 — — IOL = –2 mA
3.0 2.48 — — IOL = –6 mA
4.5 3.8 — — IOL = –12 mA
Min to
— — 0.1 V IOL = 50 µA
Max
2.3 — — 0.4 IOL = 2 mA
3.0 — — 0.44 IOL = 6 mA
4.5 — — 0.55 IOL = 12 mA
0 to 5.5 — — ±1 µAVIN = 5.5 V or GND
5.5 — — 20 µAVIN = VCC or GND, IO = 0
3.3 — 4.0 — pF VI = VCC or GND
5
Page 6
HD74LVU04A
Switching Characteristics
• VCC = 2.5 ± 0.2 V
Ta = 25°C Ta = –40 to 85°C
Item Symbol Min Typ Max Min Max Unit Test Conditions
Propagation
delay
time
• VCC = 3.3 ± 0.3 V
Item Symbol Min Typ Max Min Max Unit Test Conditions
Propagation
delay
time
t
PLH
t
PHL
— 3.2 10.9 1.0 14.0 ns CL = 15 pF A Y
— 6.6 13.4 1.0 16.0 CL = 50 pF
Ta = 25°C Ta = –40 to 85°C
t
PLH
t
PHL
— 2.5 8.9 1.0 10.5 ns CL = 15 pF A Y
— 4.7 11.4 1.0 13.0 CL = 50 pF
FROM
(Input)TO(Output)
FROM
(Input)TO(Output)
• VCC = 5.0 ± 0.5 V
Ta = 25°C Ta = –40 to 85°C
Item Symbol Min Typ Max Min Max Unit Test Conditions
Propagation
delay
time
t
PLH
t
PHL
— 2.2 5.5 1.0 6.5 ns CL = 15 pF A Y
— 3.9 7.0 1.0 8.0 CL = 50 pF
FROM
(Input)TO(Output)
6
Page 7
Operating Characteristics
• CL = 50 pF
Item Symbol V
Power
C
PD
dissipation
capacitance
(V) Min Typ Max Unit Test Conditions
CC
3.3 — 5.6 — pF f = 10 MHz
5.0 — 6.7 —
Noise Characteristics
• CL = 50 pF
Item Symbol V
Quiet output,
V
OL (P)
maximum
dynamic V
Quiet output,
OL
V
OL (V)
minimum
dynamic V
Quiet output,
OL
V
OH (V)
minimum
dynamic V
High-level
OH
V
IH (D)
dynamic put
voltage
Low-level
V
IL (D)
dynamic put
voltage
(V) Min Typ Max Unit Test Conditions
CC
3.3 — 0.5 0.8 V
3.3 — –0.1 –0.8
3.3 — 3.0 —
3.3 2.31 — — V
3.3 — — 0.99
HD74LVU04A
Ta = 25°C
Ta = 25°C
7
Page 8
HD74LVU04A
Test Circuit
Measurement point
*
C
L
• Waveform – 1
Input
In phase output
Out of phase output
Notes:
1. Input waveform: PRR ≤ 1 MHz, Zo = 50 Ω, t ≤ 3 ns, t ≤ 3 ns
2. The output are measured one at a time with one transition per measurement.
Note: C includes the probe and jig capacitance.
10%
L
t
r
50% V
90%
t
PLH
CC
90%
50% VCC
t
f
10%
50% VCC 50% VCC
t
PHL
50% VCC 50% VCC
rf
t
PHL
t
PLH
V
0 V
V
V
V
V
CC
OH
OL
OH
OL
8
Page 9
Package Dimensions
14
1
1.27
10.06
10.5 Max
1.42 Max
HD74LVU04A
Unit: mm
8
5.5
7
+ 0.20
7.80
– 0.30
2.20 Max
0.22 ± 0.05
1.15
0.20 ± 0.04
0° – 8°
0.70 ± 0.20
0.42 ± 0.08
0.40 ± 0.06
Dimension including the plating thickness
Base material dimension
0.12
0.10 ± 0.10
0.15
M
Hitachi Code
JEDEC
EIAJ
Weight
(reference value)
FP-14DA
—
Conforms
0.23 g
9
Page 10
HD74LVU04A
9.05 Max
14
Unit: mm
8.65
8
1
0.635 Max
1.27
*0.42 ± 0.08
0.40 ± 0.06
*Dimension including the plating thickness
Base material dimension
7
+ 0.11
– 0.04
0.14
0.25
3.95
1.75 Max
0.15
M
6.10
1.08
0.20 ± 0.03
*0.22 ± 0.03
+ 0.67
0.60
– 0.20
Hitachi Code
JEDEC
EIAJ
Weight
+ 0.10
– 0.30
0° – 8°
(reference value)
FP-14DN
Conforms
Conforms
0.13 g
10
Page 11
5.30 Max
14 8
17
+0.08
*0.22
–0.07
0.20 ± 0.06
5.00
0.83 Max
0.65
0.13
HD74LVU04A
Unit: mm
4.40
1.0
M
6.40 ± 0.20
0.10
1.10 Max
*Dimension including the plating thickness
Base material dimension
0.15 ± 0.04
*0.17 ± 0.05
+0.03
–0.04
0.07
0° – 8°
Hitachi Code
JEDEC
EIAJ
Weight
(reference value)
0.50 ± 0.10
TTP-14D
—
—
0.05 g
11
Page 12
Cautions
1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent,
copyright, trademark, or other intellectual property rights for information contained in this document.
Hitachi bears no responsibility for problems that may arise with third party’s rights, including
intellectual property rights, in connection with use of the information contained in this document.
2. Products and product specifications may be subject to change without notice. Confirm that you have
received the latest product standards or specifications before final design, purchase or use.
3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However,
contact Hitachi’s sales office before using the product in an application that demands especially high
quality and reliability or where its failure or malfunction may directly threaten human life or cause risk
of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation,
traffic, safety equipment or medical equipment for life support.
4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly
for maximum rating, operating supply voltage range, heat radiation characteristics, installation
conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used
beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable
failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other
consequential damage due to operation of the Hitachi product.
5. This product is not designed to be radiation resistant.
6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without
written approval from Hitachi.
7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor
products.
Hitachi, Ltd.
Semiconductor & Integrated Circuits.
Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109
URL NorthAmerica : http:semiconductor.hitachi.com/
For further information write to:
Hitachi Semiconductor
(America) Inc.
179 East Tasman Drive,
San Jose,CA 95134
Tel: <1> (408) 433-1990
Fax: <1>(408) 433-0223
Europe : http://www.hitachi-eu.com/hel/ecg
Asia (Singapore) : http://www.has.hitachi.com.sg/grp3/sicd/index.htm
Asia (Taiwan) : http://www.hitachi.com.tw/E/Product/SICD_Frame.htm
Asia (HongKong) : http://www.hitachi.com.hk/eng/bo/grp3/index.htm
Japan : http://www.hitachi.co.jp/Sicd/indx.htm
Hitachi Europe GmbH
Electronic components Group
Dornacher Stra§e 3
D-85622 Feldkirchen, Munich
Germany
Tel: <49> (89) 9 9180-0
Fax: <49> (89) 9 29 30 00
Hitachi Europe Ltd.
Electronic Components Group.
Whitebrook Park
Lower Cookham Road
Maidenhead
Berkshire SL6 8YA, United Kingdom
Tel: <44> (1628) 585000
Fax: <44> (1628) 778322
Hitachi Asia Pte. Ltd.
16 Collyer Quay #20-00
Hitachi Tower
Singapore 049318
Tel: 535-2100
Fax: 535-1533
Hitachi Asia Ltd.
Taipei Branch Office
3F, Hung Kuo Building. No.167,
Tun-Hwa North Road, Taipei (105)
Tel: <886> (2) 2718-3666
Fax: <886> (2) 2718-8180
Copyright ' Hitachi, Ltd., 1999. All rights reserved. Printed in Japan.
Hitachi Asia (Hong Kong) Ltd.
Group III (Electronic Components)
7/F., North Tower, World Finance Centre,
Harbour City, Canton Road, Tsim Sha Tsui,
Kowloon, Hong Kong
Tel: <852> (2) 735 9218
Fax: <852> (2) 730 0281
Telex: 40815 HITEC HX
Loading...