Datasheet HD74LV4053A Datasheet (HIT)

HD74LV4053A

Triple 2-channel Analog Multiplexer / Demultiplexer

ADE-205-284 (Z)

1st Edition April 1999

Description

The HD74LV4053A handles both analog and digital signals, and enables signals of either type with amplitudes of up to 5.5 V (peak) to be transmitted in either direction (at VCC = 0 V to 5.5 V). Applications include signal gating, chopping, modulation or demodulation (modem), and signal multiplexing for analog-to-digital and digital-to-analog conversion systems.

Features

• VCC = 2.0 V to 5.5 V operation

• All inputs VIH (Max.) = 5.5 V (@VCC = 0 V to 5.5 V)

Function Table

Inputs INH C B A On Channel

L L L L 1Y0, 2Y0, 3Y0 L L L H 1Y1, 2Y0, 3Y0 L L H L 1Y0, 2Y1, 3Y0 L L H H 1Y1, 2Y1, 3Y0 L H L L 1Y0, 2Y0, 3Y1 L H L H 1Y1, 2Y0, 3Y1 L H H L 1Y0, 2Y1, 3Y1 L H H H 1Y1, 2Y1, 3Y1 H X X X NONE

Note: H: High level

L: Low level X: Immaterial

HD74LV4053A

Pin Arrangement

2Y1 2Y0 3Y1

3–COM

3Y0 INH

GND GND

1 2 3 4 5

6 7 8 9

(Top view)

16 15 14 13 12 11

10

V

CC

2–COM 1–COM

1Y1 1Y0 A

B

C

2

HD74LV4053A

Absolute Maximum Ratings

Item Symbol Ratings Unit Conditions

Supply voltage range V Input voltage range* Output voltage range*

1

1, 2

Input clamp current I Output clamp current I Continuous output current I Continuous current through

V

or GND

CC

Maximum power dissipation at Ta = 25°C (in still air)*

3

CC

V

I

V

O

IK

OK

O

or I

I

CC

GND

P

T

Storage temperature Tstg –65 to 150 °C Notes: The absolute maximum ratings are values which must not individually be exceeded, and furthermore,

no two of which may be realized at the same time.

1. The input and output voltage ratings may be exceeded even if the input and output clamp-current ratings are observed.

2. This value is limited to 5.5 V maximum.

3. The maximum package power dissipation was calculated using a junction temperature of 150°C.

–0.5 to 7.0 V –0.5 to 7.0 V –0.5 to VCC + 0.5 V Output: H or L –20 mA VI < 0

±50 mA VO < 0 or VO > V ±25 mA VO = 0 to V

CC

±50 mA

785 mW SOP

500 TSSOP

CC

Recommended Operating Conditions

Item Symbol Min Max Unit Conditions

1

Supply voltage range V Input voltage range V Output voltage range V

CC

I

I/O

2.0* 0 5.5 V 0VCCV

Input transition rise or fall rate ∆t /∆v 0 200 ns/V VCC = 2.3 to 2.7 V

0 100 VCC = 3.0 to 3.6 V 020 V

Operating free-air temperature Ta –40 85 °C Notes: Unused or floating inputs must be held high or low.

1. With the supply voltage at or around 2 V, the analog switch on-state resistance loses linearity significantly. It is recommended that only digital signals be transmitted at these low supply voltages.

5.5 V

= 4.5 to 5.5 V

CC

3

HD74LV4053A

Logic Diagram

A

B

C

2–COM 1–COM

1Y0

1Y1

2Y0

2Y1

3Y0

3Y1

INH

3–COM

4

HD74LV4053A

OU

DC Electrical Characteristics

Ta = 25°C Ta = –40 to 85°C

Item Symbol VCC (V) Min Typ Max Min Max Unit Test Conditions

Input voltage V

On-state

IH

V

IL

R

ON

switch resistance

Peak on

R

ON (P)

resistance

Difference of

∆R

ON

on-state resistance between switches

Off-state

Is (OFF) 5.5 — — ±0.1 — ±1.0 µAVIN = VCC, V switch leakage current

On-state

Is (ON) 5.5 — — ±0.1 — ±1.0 µAVIN = VCC or GND switch leakage current

Input current I Quiescent

IN

I

CC

supply current

Note: For conditions shown as Min or Max use the appropriate values under recommended operating

conditions.

2.0 — — — 1.5 — V

2.3 to 2.7 — — — V

3.0 to 3.6 — — — V

4.5 to 5.5 — — — V

× 0.7 —

CC

× 0.7 —

CC

× 0.7 —

CC

2.0 — — — — 0.5

2.3 to 2.7 — — — — V

3.0 to 3.6 — — — — V

4.5 to 5.5 — — — — V

CC

× 0.3 × 0.3 × 0.3

2.3 — 60 180 — 225 Ω VIN = VCC or GND V

= V

INH

IL

IT = 2 mA

3.0 — 50 150 — 190

4.5 — 40 75 — 100

2.3 — 200 500 — 600 Ω VIN = VCC to GND V

= V

INH

IL

IT = 2 mA

3.0 — 90 180 — 225

4.5 — 50 100 — 125

2.3 — 20 30 — 40 Ω VIN = VCC to GND V

= V

INH

IL

IT = 2 mA

3.0 — 10 20 — 30

4.5 — 7 15 — 20

=

T

GND or VIN = GND, VO = VCC, V

V

= V

INH

= V

INH

IL

0 to 5.5 — — ±0.1 — ±1.0 µAVIN = 5.5 V or GND

5.5 — — — — 20 µAVIN = VCC or GND

IH

5

HD74LV4053A

Switching Characteristics

• VCC = 2.5 ± 0.2 V

Ta = 25°C Ta = –40 to 85°C

Item Symbol Min Typ Max Min Max Unit Test Conditions

Propagation delay time

Enable time t

Disable time

• VCC = 3.3 ± 0.3 V

Item Symbol Min Typ Max Min Max Unit Test Conditions

Propagation delay time

Enable time t

Disable time

t

PLH

t

PHL

— 2.5 10.0 — 16.0 ns CL = 15 pF COM

— 5.0 12.0 — 18.0 CL = 50 pF

ZH

t

ZL

— 7.0 18.0 — 23.0 ns RL = 1 kΩ CL = 15 pF INH COM

— 9.0 28.0 — 35.0 CL = 50 pF

t

HZ

t

LZ

— 9.0 18.0 — 23.0 ns RL = 1 kΩ CL = 15 pF INH COM

— 13.0 28.0 — 35.0 CL = 50 pF

Ta = 25°C Ta = –40 to 85°C

t

PLH

t

PHL

— 2.0 6.0 — 10.0 ns CL = 15 pF COM

— 4.0 9.0 — 12.0 CL = 50 pF

ZH

t

ZL

— 5.0 12.0 — 15.0 ns RL = 1 kΩ CL = 15 pF INH COM

— 7.0 20.0 — 25.0 CL = 50 pF

t

HZ

t

LZ

— 7.0 12.0 — 15.0 ns RL = 1 kΩ CL = 15 pF INH COM

— 10.0 20.0 — 25.0 CL = 50 pF

FROM (Input)TO(Output)

Yn or

or Yn

COM

or Yn

FROM (Input)TO(Output)

Yn or

or Yn

COM

or Yn

6

Switching Characteristics (cont)

• VCC = 5.0 ± 0.5 V

Ta = 25°C Ta = –40 to 85°C

Item Symbol Min Typ Max Min Max Unit Test Conditions

Propagation delay time

Enable time t

Disable time

t

PLH

t

PHL

— 1.5 4.0 — 7.0 ns CL = 15 pF COM

— 3.0 6.0 — 8.0 CL = 50 pF

ZH

t

ZL

— 4.0 8.0 — 10.0 ns RL = 1 kΩ CL = 15 pF INH COM

— 5.0 14.0 — 18.0 CL = 50 pF

t

HZ

t

LZ

— 5.0 8.0 — 10.0 ns RL = 1 kΩ CL = 15 pF INH COM

— 8.0 14.0 — 18.0 CL = 50 pF

HD74LV4053A

FROM (Input)TO(Output)

Yn or

or Yn

COM

or Yn

7

HD74LV4053A

O

/OU

Switching Characteristics (cont)

Ta = 25°C

Item Symbol V

Control input

C

IC

capacitance Common terminal

C

IS

capacitance Switch terminal

C

I/O

capacitance Feedthrough

C

T

capacitance Power dissipation

C

PD

capacitance Frequency

response (Switch ON)

Crosstalk (Between any switches)

Crosstalk (Control input to signal output)

(V) Min Typ Max Unit Test Conditions

CC

— — 4.5 — pF

— — 12.5 — pF

— — 7.0 — pF

— — 0.5 — pF

— — 9.0 — pF

2.3 — 30.0 — MHz CL = 50 pF, RL = 600 Ω

3.0 — 35.0 —

4.5 — 50.0 —

2.3 — –45.0 — dB CL = 50 pF, RL = 600 Ω

3.0 — –45.0 —

4.5 — –45.0 —

2.3 — 20.0 — mV CL = 50 pF, RL = 600 Ω

3.0 — 35.0 —

4.5 — 65.0 —

Adjust fin voltage to obtain 0 dBm at output when fin is 1 MHz (sine wave). Increase f

in

frequency until the dBmeter reads –3 dBm.

20 log (V

/VI) = –3

dBm

Adijust fin voltage to obtain 0 dBm at input when fin is 1 MHz (sine wave).

Adjust RL value to obtain 0 A at I

IN

when fin is

T

1 MHz (squave wave).

FROM (Input)TO(Output)

COM or Yn

Yn or COM

COM Yn

INH COM

or Yn

8

Switching Characteristics (cont)

Ta = 25°C

Item Symbol V

Feedthrough attenuation (Switch OFF)

Sine-wave

distortion

(V) Min Typ Max Unit Test Conditions

CC

2.3 — –45 — dB CL = 50 pF, RL = 600 Ω

3.0 — –45 —

4.5 — –45 —

2.3 — 0.1 — % CL = 50 pF, RL = 10 kΩ

3.0 — 0.1 —

4.5 — 0.1 —

Adjust fin voltage to obtain 0 dBm at input when fin is 1 MHz (sine wave).

fIN = 1 kHz (sine wave) VI = 2 V VI = 2.5 V V VI = 4 V

, VCC = 2.3 V

P-P

, VCC = 3.0

P-P

, VCC = 4.5 V

P-P

HD74LV4053A

FROM (Input)TO(Output)

COM or Yn

Yn or COM

9

HD74LV4053A

Test Circuits

R : On-state switch resistance

ON

V = V

INH IL

V = V or GND

IN CC

Is (OFF): Off-state switch leakage current, Is (ON): On-state switch leakage current

V = V

INH IH

V

(ON)

GND

V

CC

2.0 mA V

V

CC

V –V

IN OUT

V

OUT

V –V

R = (Ω)

ON

IN OUT

2 × 10

–3

V

CC

AAB

(OFF)

GND

V

(ON)

GND

CC

Open

V = V

INH IL

A

AB

10

t , t : Propagation delay time (from switch input to switch output)

PLH PHL

V

V = V

INH IL

CC

V

CC

(ON)

R =

L

50

GND

Ω

C = 15 or

L

50 pF

Switching time

V

CC

R =

L

50

Ω

V

S1

INH

V

IN

CC

GND

V

OUT

R =

L

1 k

Ω

C = 15 or

L

50 pF

HD74LV4053A

BA

S2

V

INH

OUT

INH

OUT

50%

t

ZL

50% t

LZ

V

CC

50%

V

CC

V +0.3 V

OL

TEST S1 S2

t /t

LZ ZL

t /t

HZ ZH

V

CC

V

INH

GND

VCC

50%

0 V ≈V

CC

V

OUT

INH

OUT

50%

t

HZ

V

CC

V

OL

V

CC

0 V ≈V

CC

V

OL

t

ZH

CC

V

GND

V

CC

V

50%

V

CC

V –0.3 V

OH

CC

V

CC

0 V

V

OH

≈0 V

V

CC

0 V

V

OH

≈0 V

11

HD74LV4053A

Frequency response (Switch ON)

Crosstalk (Between any switches)

0.1 µF

f

in

R =

L

50

V

(ON)

GND

CC

V = V

INH

IL

0.1 µF

f

in

R = 50

V

IN

L

Ω

V /2

V = GND

INH

V =V

CC

C

V

CC

f = sine wave

R =

L

600

CC

in

Ω

V

C = 50 pF

L

OUT

or GND

R =

L

600

Ω

V

IN

Ω

V

(ON)

GND

CC

R =

L

600

Ω

V

C = 50 pF

L

OUT1

R = 600

V /2

CC

L

Ω

V = GND

INH

V =V

CCC

or GND

V

(OFF)

GND

CC

V /2

CC

R = 600

V /2

CC

V

OUT2

L

Ω

C = 50 pF

L

12

Crosstalk (Control input to signal output)

R =

L

50

Ω

V

INH

R =

L

600

Ω

V

CC

V

CC

GND

R =

L

600

Ω

HD74LV4053A

V

OUT

C = 50 pF

L

V /2

CC

Feedthrough attenuation (Switch OFF)

V = V

INH

IH

R =

0.1 µF

f

in

R =

L

50

L

600

Ω

V

IN

R =

L

Ω

V /2

CC

600

Ω

Sine-wave distortion

V = V

INH

IL

10 µF

f

in

V

IN

V

CC

(OFF)

GND

V

CC

(ON)

GND

CC

V /2

CC

R = 600

V /2

CC

R = 10 k

V /2

CC

V

OUT

L

Ω

C = 50 pF

L

V

C = 50 pF

L

OUT

13

HD74LV4053A

Package Dimensions

16

Unit: mm

10.06

10.5 Max 9

5.5

1

0.80 Max

1.27

*0.42 ± 0.08

± 0.06

0.40

*Dimension including the plating thickness

Base material dimension

8

0.12

0.10 ± 0.10

0.15

M

2.20 Max

7.80

0.20 ± 0.04

*0.22 ± 0.05

0.70 ± 0.20

Hitachi Code JEDEC EIAJ Weight

(reference value)

+ 0.20 – 0.30

1.15

0

° – 8°

FP-16DA — Conforms

0.24 g

14

16

HD74LV4053A

Unit: mm

9.9

10.3 Max 9

1

1.27

0.635 Max

*0.42 ± 0.08

0.40 ± 0.06

*Dimension including the plating thickness

Base material dimension

8

0.25

+ 0.11

– 0.04

0.14

0.15

3.95

1.75 Max

M

6.10

1.08

0.20 ± 0.03

*0.22 ± 0.03

+ 0.67

0.60

– 0.20

Hitachi Code JEDEC EIAJ Weight

+ 0.10 – 0.30

0° – 8°

(reference value)

FP-16DN Conforms Conforms

0.15 g

15

HD74LV4053A

*0.22

0.20 ± 0.06

5.0

5.3 Max

16 9

4.40

18

0.65

+ 0.08 – 0.07

0.13

0.65 Max

Unit: mm

1.0

M

6.40 ± 0.20

0.10

1.10 Max

*Dimension including the plating thickness

Base material dimension

0.15 ± 0.04

*0.17 ± 0.05

+0.03

–0.04

0.07

0° – 8°

Hitachi Code JEDEC EIAJ Weight

(reference value)

0.50 ± 0.10

TTP-16DA — —

0.05 g

16

Cautions

1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent, copyright, trademark, or other intellectual property rights for information contained in this document. Hitachi bears no responsibility for problems that may arise with third party’s rights, including intellectual property rights, in connection with use of the information contained in this document.

2. Products and product specifications may be subject to change without notice. Confirm that you have received the latest product standards or specifications before final design, purchase or use.

3. Hitachi makes every attempt to ensure that its products are of high quality and reliability. However, contact Hitachi’s sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury, such as aerospace, aeronautics, nuclear power, combustion control, transportation, traffic, safety equipment or medical equipment for life support.

4. Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating, operating supply voltage range, heat radiation characteristics, installation conditions and other characteristics. Hitachi bears no responsibility for failure or damage when used beyond the guaranteed ranges. Even within the guaranteed ranges, consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as failsafes, so that the equipment incorporating Hitachi product does not cause bodily injury, fire or other consequential damage due to operation of the Hitachi product.

5. This product is not designed to be radiation resistant.

6. No one is permitted to reproduce or duplicate, in any form, the whole or part of this document without written approval from Hitachi.

7. Contact Hitachi’s sales office for any questions regarding this document or Hitachi semiconductor products.

Hitachi, Ltd.

Semiconductor & Integrated Circuits. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Tel: Tokyo (03) 3270-2111 Fax: (03) 3270-5109

URL NorthAmerica : http:semiconductor.hitachi.com/

For further information write to:

Hitachi Semiconductor (America) Inc. 179 East Tasman Drive, San Jose,CA 95134 Tel: <1> (408) 433-1990 Fax: <1>(408) 433-0223

Europe : http://www.hitachi-eu.com/hel/ecg Asia (Singapore) : http://www.has.hitachi.com.sg/grp3/sicd/index.htm Asia (Taiwan) : http://www.hitachi.com.tw/E/Product/SICD_Frame.htm Asia (HongKong) : http://www.hitachi.com.hk/eng/bo/grp3/index.htm Japan : http://www.hitachi.co.jp/Sicd/indx.htm

Hitachi Europe GmbH Electronic components Group Dornacher Stra§e 3 D-85622 Feldkirchen, Munich Germany Tel: <49> (89) 9 9180-0 Fax: <49> (89) 9 29 30 00

Hitachi Europe Ltd. Electronic Components Group. Whitebrook Park Lower Cookham Road Maidenhead Berkshire SL6 8YA, United Kingdom Tel: <44> (1628) 585000 Fax: <44> (1628) 778322

Hitachi Asia Pte. Ltd. 16 Collyer Quay #20-00 Hitachi Tower Singapore 049318 Tel: 535-2100 Fax: 535-1533

Hitachi Asia Ltd. Taipei Branch Office 3F, Hung Kuo Building. No.167, Tun-Hwa North Road, Taipei (105) Tel: <886> (2) 2718-3666 Fax: <886> (2) 2718-8180

Hitachi Asia (Hong Kong) Ltd. Group III (Electronic Components) 7/F., North Tower, World Finance Centre, Harbour City, Canton Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: <852> (2) 735 9218 Fax: <852> (2) 730 0281 Telex: 40815 HITEC HX