How it Works
Datasheet
Loading...
H34063AP
Datasheet (HSMC)
6 pgs72.89 Kb0

Datasheet H34063AP Datasheet (HSMC)

Download
Page 1
HI-SINCERITY
MICROELECTRONICS CORP.
H34063AP
Description
The H34063AP Series is a monolithic control circuit containing the primary functions required for DC-to-DC converters. These devices consist of an internal temperature compensated reference, comparator, controlled duty cycle oscillator with an active current limit circuit, driver and high current output switch. This series was specifically by Hi-Sincerity Microelectronics Corp.
Features
3V to 40V Input Voltage Operation
•
Internal 1.6A Peak Current Switch
•
Internal ±1.8% Reference
•
Low Quiescent Current at 1.6mA
•
Frequency Operation from 100Hz~100KHz
•
Current Limiting
•
Spec. No. : Preliminary Data Issued Date : 1998.08.01 Revised Date : 1999.06.01 Page No. : 1/6
Applications
Saver for Cellular Phone
•
DC-DC Converter Module
•
Typical Application Circuit
Fig1.Saver Circuit for Cellular Phone
RSC
V
in
C1
100µF
H34063AP
8 7
6 5
RA
5.6k
Ω
RB
33k
L1
200µH
1
2 3
C
4
Ω
T
470ρF
D1 H1N5819
V
out
C
out
220µF
HSMC Product Specification
Page 2
Pin Connections
HI-SINCERITY
MICROELECTRONICS CORP.
Spec. No. : Preliminary Data Issued Date : 1998.08.01 Revised Date : 1999.06.01 Page No. : 2/6
5678
Pin1:Switch Collector Pin5:Comparator Inverting Input Pin2:Switch Emitter Pin6:Vcc Pin3:Timing Capacitor Pin7:Ipk Sense
1234
Pin4:Gnd Pin8:Driver Collector
Absolute Maxium Rating
Supply Voltage ..................................................................................................................... 40 V
Comparator Input Voltage Range ............................................................................. -0.3V ~ 40 V
Switch Collector Voltage ...................................................................................................... 40 V
Switch Emitter Voltage ......................................................................................................... 40 V
Switch Collector to Emitter Voltage ...................................................................................... 40 V
Driver Collector Voltage ....................................................................................................... 40 V
Switch Current ..................................................................................................................... 1.6 A
Power Dissipation DIP Package Ta=25°C .......................................................................... 1.0 W
Thermal Resistance Junction To Air............................................................................ 125 °C / W
Operating Junction Temperature ........................................................................................ 125 °C
Operating Ambient Temperature Range ........................................................................ 0 ~ 70 °C
Storage Temperature Range................................................................................ -40 °C ~ 125 °C
Electrical Characteristics
(Vcc=5V,Ta=25°C, unless otherwise specified)
Parameter Test Condition Symbol Min. Typ. Max. Unit
Oscillator
Charging Current Discharge Current
5.0V≤V
5.0V≤V
CC CC
≤ ≤
40V
40V Voltage Amplitude Pin3 V Discharge to Charge Current Ratio V Current Limit Sense Voltage I
IPK(Sense)
Chg=Idischg
=V
CC
I
chg
I
dischg
OSC
I
Dischg/Ichg
V
IPK(Sence)
24 35 42 uA
140 220 260 uA
-0.6- V
5.2 6.5 7.5
250 300 350 mV
Output Switch
Saturation Voltage, Darlington Connection
Saturation Voltage
ISW=1.0A, V
C(Driver)=
I
=1.0A,
SW
I
C(Driver)
=50mA
VC(Switch)
V
CE(Sat)
V
CE(Sat)
-1.01.3V
-0.40.7V
(Forced β ≈ 20) DC Current Gain ISW=1.0A, VCE=5.0V hFE 50 75 - V Collector Off-State Current VCE=30V I
CC(Off)
- 0.01 100 UA
Comparator
Threshold Voltage Threshold Voltage Threshold Voltage Line Regulation
0°C≤Ta≤70°C
3.0V≤V
CC
≤
40V
Regline - 1.5 6 mV
Input Bias Current VIN=0V I
V
IPK(Sence)=VCC
V
,
>
Pin5
T
FB
40V
≤
CC
=0.0001uF,Pin2=Gnd
Supply Current
V
5.0V≤V
C
V
I
FB
IB
CC
1.227
1.210
1.250-1.273
1.29
- -20 -400 nA
-1.63mA
Remaining pins open
V
HSMC Product Specification
Page 3
Block Diagram
g
r
HI-SINCERITY
MICROELECTRONICS CORP.
Spec. No. : Preliminary Data Issued Date : 1998.08.01 Revised Date : 1999.06.01 Page No. : 3/6
DRI Pin8:Driver Collector
IPK Pin7:Highside Current Se ns e Input, VCC-VIPK=300mV
VCC Pin6:Power Supply Input
FB Pin5:Feedback Comparator Inverting Input
Pin1:1.6A Switch Collector
Pin2:Darlington Switch Emitter
Pin3:Oscilletor Timin
Pin4:Power GND
Capacito
GND
SC
SE
TC
Q2
Q1
80
CT
1.25V
Reference Voltage
QS
R
Ω
IPK
Oscillator
Comparator
+
-
Application Information
Design Formula Table
Calculation Step-Down Step-Up Voltage-Inverting
V
ton / t
(ton + t
I
C(switch)
off
) max 1/F
off
C
T
V
in(min)
out+VF
4*10-5t
2*I
RS 0.3 / I
(V
L
(min)
C
O
sat
V
: Saturation voltage of the output switch.
F
: Forward voltage drop of the ringback rectifier.
V The following power supply characteristics must be chosen :
in
V
: Nominal input voltage.
out
V
: Desired output voltage. |V
out
I
- Desired output current
Fmin : Minimum desired output switching frequency at the selected values for V
Ripple(P-P)
V due to the capacitor equ iv ale nt s er ies re sis ta nc e an d bo ar d layout. The ripple volt age s hou ld be kept to a low value since it will directly effect the line and load regulation.
: Desired peak to peak output ripple v oltage in practice, the calculat ed value will need to be incr eased
in(min)-Vsat-Vout
*t
I
C(switch)
8V
Ripple(P-P)
/
-V
sat-VOut
min
on
out(max)
C(switch)
I
/
C(switch)
on(max)
*(ton+t
out
|=1.25*(1+RB/RA)
off)
/
Vout+VF-V
V
in(min)-Vsat
1/F
min
4*10-5t
2*I
out(max)(ton+toff/toff
0.3 / I
C(switch)
)
(V
in(min)-Vsat
I
out*ton
*t
on(max)
/ V
/
Ripple(P-P)
in(min)
on
I
C(switch)
/
)2*I
|V
out(max)(ton+toff/toff
0.3 / I
)
in
and I
(V
in(min)-Vsat
I
out*ton
out
.
| + V
out
Vin-V
1/F
min
4*10-5t
C(switch)
*t
on(max)
/ V
F /
sat
on
I
/
C(switch)
Ripple(P-P)
)
)
HSMC Product Specification
Page 4
HI-SINCERITY
Q
(
MICROELECTRONICS CORP.
Application Information
Fig.2 Step-Up Converter
RSC
0.22
in
V
2.2k
(Continuos)
R1
Ω
150
C1 100µF
RA
Ω
Spec. No. : Preliminary Data Issued Date : 1998.08.01 Revised Date : 1999.06.01 Page No. : 4/6
L1
H34063AP
8
1 2
7
3
6
4
5
RB
Ω
47k
D1
T
C 680ρF
out
C 220µF
out
V 28V / 200mA
Line Regulation : 100mV (Vin=8V~16V, @Io=200mA) Load Regulation : 5mV (Vin=12V, @Io=80mA~200mA)
Fig.3 Step-Up Converter With External NPN Switch
L1
R1
RSC
in
V
C1
RA
H34063AP
8
1 2
7
3
6
4
5
RB
C
Fig.4 Step-Down Converter
H34063AP
8
RSC
0.25
in
V
C1 100µF
1
2
7 6
3
5
4
RB
R2
T
T
C 470ρF
D1
1
L1
D1 H1N5819
out
V
out
C
out
V 5V / 500mA
out
C 470µF
Ω
3.6k
RA
Ω
1.2k
Line Regulation : 40mV (Vin=10V~20V, @Io=500mA) Load Regulation : 5mV (Vin=15V, @Io=10mA~500mA) Short Circuit Current : 1.3A
Vin=15V, @RL=0.1
HSMC Product Specification
Ω
Page 5
HI-SINCERITY
Q
µ
Q
MICROELECTRONICS CORP.
Fig.5 Step-Down Converter With External PNP Saturation Switch
Spec. No. : Preliminary Data Issued Date : 1998.08.01 Revised Date : 1999.06.01 Page No. : 5/6
RSC
in
V
C1
RA
Fig.6 Voltage Inverting Converter
RSC
0.25
in
V
4.5V-6V
H34063AP
8
1 2
7
3
6
4
5
RB
H34063AP
8 7 6 5
R2
R1
1
L1
out
V
T
C
D1 H1N5819
1 2 3
4
C
L1 100
T
D1
out
C
out
V
-12V / 100mA
out
H
C 470µF
680ρF
C1
RA
100µF
Ω
RB
8.2k
953
Ω
Line Regulation : 20mV (Vin=4.5V~6V, @Io=100mA) Load Regulation : 100mV (Vin=5V, @Io=10mA~100mA)
Fig.7 Voltage Inverting Converter With External PNP Saturation Switch
H34063AP
R1
8
RSC
in
V
1 2
7
3
6
4
5
RA
C1
RB
R2
1
L1
T
C
D1
C
out
out
V
HSMC Product Specification
Page 6
HI-SINCERITY
g
MICROELECTRONICS CORP.
DIP-8P Dimension
5
87
6
Spec. No. : Preliminary Data Issued Date : 1998.08.01 Revised Date : 1999.06.01 Page No. : 6/6
Marking :
A
1
432
HSMC Logo
Part Number
Date Code
Package Code
Ink Mark
B
J
DIP-8P Plastic Package
DIM
F
α
1
C
E
G
H
D
I
M
Inches Millimeters Inches Millimeters
Min. Max. Min. Max.
K
L
DIM
Min. Max. Min. Max.
HSMC Packa
e Code : P
A 0.2480 0.2520 6.29 6.40 H 0.0150 0.0210 0.38 0.53
B 0.3630 0.3670 9.22 9.32 I 0.0898 0.1098 2.28 2.79 C-*0.0600 - *1.52 J 0.2950 0.3050 7.49 7.74 D - *0.0500 - *1.27 K - *0.1181 - *3.00
E - *0.0390 - *0.99 L 0.3370 0.7470 8.56 8.81
F 0.1280 0.1320 3.25 3.35 M 0.0090 0.0150 0.229 0.381 G 0.1250 0.1400 3.17 3.55
Notes :
Material :
• Lead : 42 Alloy ; solder plating
• Mold Compound : Epoxy resin family, flammability solid burning class:UL94V-0
1.Dimension and tolerance based on our Spec. dated Sep. 07,1997.
2.Controlling dimension : millimeters.
3.Maximum lead thickness includes lead finish thickness, and minimum lead thickness is the minimum thickness of base material.
4.If there is any question with packing specification or packing method, pleas e contact your l ocal HSMC sal es office.
194°97
α
°
94
°
*:Typical
97
°
Important Notice :
• All rights are reserved. Reproduction in whole or in part is prohibited without the prior written approval of HSMC.
• HSMC reserves the right to make changes to its products without notice.
•
HSMC semiconductor products are not warranted to be suitable for use in Life-Support Applications, or systems.
• HSMC assumes no liability for any consequence of customer product design, infringem e nt of patents, or applic ati on assistance.
Head Office And Factory :
•
Head Office
Tel : 886-2-25212056 Fax : 886-2-25632712, 25368454
•
Factory 1 :
Tel : 886-3-5983621~5 Fax : 886-3-5982931
•
Factory 2 :
Tel : 886-3-5977061 Fax : 886-3-5979220
(Hi-Sincerity Microelectronics Corp.) : 10F.,No. 61, Sec. 2, Chung-Shan N. Rd. Taipei Taiwan R.O.C.
No. 38, Kuang Fu S. Rd., Fu-Kou Hsin-Chu Industrial Park Hsin-Chu Taiwan. R.O.C
No. 17-1, Ta-Tung Rd., Fu-Kou Hsin-Chu Industrial Park Hsin-Chu Taiwan. R.O.C
HSMC Product Specification
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use