Page 1
F
M
M
ts
50
35 70
Maximum Average Forward Rectified Current
2. Thermal Resistance from Junction to Case Per Leg Mounted on Heatsink.
查询FRF501G供应商
FRF501G THRU FRF507G
Isolation 5.0 AMPS. Glass Passivated Fast Recovery Rectifiers
eatures
Low forward voltage drop
High current capability
High reliability
High surge current capability
echanical Data
Cases: ITO-220AB molded plastic
Epoxy: UL 94V-0 rate flame retardant
Terminals: Leads solderable per
MIL-STD-202, Method 208 guaranteed
Polarity: As marked
High temperature soldering guaranteed:
260℃/10 seconds 0.25”,(6.35mm) from
case.
Mounting position: Any
Weight: 2.24 grams
Mounting torque: 5 in – 1bs. max.
Voltage Range
50 to 1000 Volts
Current
5.0 Amperes
ITO-220AB
.134(3.4)DIA
.113(3.0)DIA
.272(6.9)
.248(6.3)
.110(2.8)
.098(2.5)
Dimensions in inches and (millimeters)
.112(2.85)
.100(2.55)
.606(15.5)
.583(14.8)
.543(13.8)
.512(13.2)
aximum Ratings and Electrical Characteristics
Rating at 25℃ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
See Fig. 1
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated
Load (JEDEC method )
Maximum Instantaneous Forward Voltage
@2.5A
Maximum DC Reverse Current @ TC=25℃
at Rated DC Blocking Voltage @ TC=125℃
Maximum Reverse Recovery Time ( Note 1)
Typical Thermal Resistance (Note 2)
Operating and Storage Temperature Range
Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
Symbol FRF
V
RRM
V
RMS
VDC 50 100 200 400 600 800 1000 V
I
5.0 A
(AV)
I
30 A
FSM
VF 1.5 V
IR
Trr 150 250
R
θ
JA
TJ, T
STG
501G
FRF
FRF
FRF
FRF
502G
503G
504G
505G
100 200 400 600 800 1000 V
140 280 420 560 700 V
5.0
100
4.0
-65 to +150
FRF
507G
506G
500 nS
FRF
Uni
uA
uA
℃/W
℃
- 448 -
Page 2
RATINGS AND CHARACTERISTIC CURVES (FRF501G THRU FRF507G)
FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50W
NONINDUCTIVE
(+)
50Vdc
(approx)
(-)
NOTES: 1. Rise Time=7ns max. Input Impedance=
FIG.2- MAXIMUM FORWARD CURRENT DERATING
5.0
4.0
3.0
2.0
1.0
AVERAGE FORWARD CURRENT. (A)
30
25
20
15
10
PEAK FORWARD SURGE CURRENT. (A)
CURVE
0
0
LEAD TEMPERATURE. ( C)
FIG.3- MAXIMUM NON-REPETITIVE FORWARD
SURGE CURRENT PER LEG
5
0
1
2 5 10 20 10050
FIG.4- TYPICAL JUNCTION CAPACITANCE PER LEG
300
250
200
150
100
CAPACITANCE.(pF)
0
Tj=25 C
f=1.0MHz
50
Vsig=50mVp-p
0
0.1 0.5 1.0 5 10 50 100 500 1000
10W
NONINDUCTIVE
DUT
1W
NON
INDUCTIVE
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
50 100 150
NUMBER OF CYCLES AT60Hz
REVERSE VOLTAGE. (V)
OSCILLOSCOPE
(NOTE 1)
o
8.3ms Single Half Sine Wave
JEDEC Method
PULSE
GENERATOR
(NOTE 2)
+0.5A
(-)
-0.25A
(+)
-1.0A
FIG.2- TYPICAL REVERSE CHARACTERISTICS
1000
INSTANTANEOUS REVERSE CURRENT.(A)
FIG.6- TYPICAL INSTANTANEOUS FORWARD
0.04
INSTANTANEOUS FORWARD CURRENT. (A)
0.02
0.01
trr
0
1cm
SET TIME BASE FOR
5/ 10ns/ cm
PER LEG
100
0
Tj=125 C
10
1.0
0.1
0
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
CHARACTERISTICS PER LEG
8.0
4.0
2.0
1.0
0.4
0.2
0.1
0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5
INSTANTANEOUS FORWARD VOLTAGE. (V)
0
Tj=25 C
20 40 60 80 100 120 140
o
Tj=25 C
Pulse Width=300 s
1% Duty Cycle
- 449 -
Loading...