Datasheet EN1CN1, EN1C23, EN1C22, EN1C21, EN1C13 Datasheet (VICOR)

...
Page 1
Set your site on VICOR at www.vicorpower.com
PRELIMINARY
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 ENMods System: FARM3 and MiniHAM Rev. 1.3 Page 1 of 12
Parameter Rating Unit Notes
L to N voltage (FARM3) 264 Vrms Continuous L to N voltage (FARM3) 280 Vrms 100ms +Out to –Out voltage (FARM3) 400 Vdc BOK to –Out voltage (FARM3) 16 Vdc EN to –Out voltage (FARM3) 16 Vdc Mounting torque 4-6(0.45-0.68) in-lbs (N-m) 6 each, 4-40 screw Pin soldering temperature 500 (260) °F (°C) <5 sec; wave solder Pin soldering temperature 750 (390) °F (°C) <7 sec; hand solder Output current 3.5 A
Features
Harmonic Current Attenuation to
EN61000-3-2
EMI Filtering to
EN55022, Level B
Transient Immunity to
EN61000-4-5
575W Rated Power Output
Autoranging 115/230Vac Input
Microprocessor Control
Inrush Current Limiting
Product Highlights
The ENMods system is a new AC front end solution for compliance to electromagnetic compatibility (EMC) standards. It consists of the MiniHAM — a passive harmonic attenuation module and the FARM3 — an auto ranging AC-DC front end module. Combined with the filtering and hold-up capacitors as specified herein, the ENMods system provides full compliance to:
EN61000-3-2 Harmonic Current EN55022, Level B Conducted Emissions EN61000-4-5 Surge Immunity EN61000-4-11 Line Disturbances
The MiniHAM is the first passive product specifically designed for compliance to EN harmonic current limits. Unlike active PFC solutions, the MiniHAM generates no EMI, greatly simplifying and reducing system noise filtering requirements. It is also considerably smaller and more efficient than active alternatives and improves MTBF by an order of magnitude. Optimized for operation on the DC bus (provided by the FARM3) rather than directly on the AC line, it will provide harmonic current compliance up to 600W of input power at 230Vac.
The 115/230Vac input FARM3 is a new member of Vicor’s Filter and Autoranging Module product line that has been optimized for use as the front end for the MiniHAM. Both modules are in Vicor’s standard Mini half-brick package. Together with Vicor’s 1st or 2nd Generation 300V input DC-DC converters, they form the basis of a low noise, high efficiency, rugged, simple and reliable EN compliant power system.
Data Sheet
ENMods
TM
Component Power Front End System for EN Compliance
45
Each module:
2.28 x 2.2 x 0.5 in
57,9 x 55,9 x 12,7 mm
Absolute Maximum Ratings
Thermal Resistance
Parameter Typ Unit
Baseplate to sink; flat, greased surface 0.16 °C/Watt Baseplate to sink; with thermal pad (P/N 20264) 0.14 °C/Watt Baseplate to ambient 8.0 °C/Watt Baseplate to ambient; 1000 LFM 1.9 °C/Watt
EN1 C 1 1
Product
Type*
Baseplate 1 = Slotted 2 = Threaded 3 = Thru-hole
Pin Style**
1 = Short Pin 2 = Long Pin S = Short ModuMate N = Long ModuMate
Product Grade C = –20°C to +100°C T = –40°C to +100°C H = –40°C to +100°C M = –55°C to +100°C
Part Numbering
*EN1 product includes one each MiniHAM and FARM3 with same product grade, pin and baseplate style.
**Pin styles S & N are compatible with the ModuMate interconnect system for socketing and surface mounting.
Page 2
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 ENMods System: FARM3 and MiniHAM Rev. 1.3 Page 2 of 12
Set your site on VICOR at www.vicorpower.com
PRELIMINARY
Parameter Min Typ Max Unit Notes
Operating input voltage 90 115 132 Vac Autoranging (doubler mode) Operating input voltage 180 230 264 Vac Autoranging (bridge mode) Input undervoltage 90 Vac No damage AC line frequency 47 63 Hz C-,T-, H- and M-Grade Power factor 0.68 0.72 Typical line Inrush current 30 Amps 264Vac line voltage Efficiency 94 96 % Full load AC Bus OK (BOK)
Low state resistance 15 To negative output - Bus normal Low state current 50 mA Bus normal High state voltage 14.8 15.0 15.2 Vdc Bus abnormal, 27k internal pull up to 15Vdc (see Figure12) BOK true threshold 235 240 245 Vdc Output Bus voltage BOK false threshold 200 205 210 Vdc Output Bus voltage
Module Enable (EN)
Low state resistance 15 To negative output - Converters disabled Low state current 50 mA High state voltage 14.8 15.0 15.2 Vdc 150k internal pull up to 15Vdc (see Figure 11) Enable threshold 235 240 Vdc Output bus voltage Disable threshold 185 190 195 Vdc Output bus voltage
AC Bus OK - Module Enable, differential error* 15 17 20 Vdc AC Bus OK and Module Enable thresholds track
FARM3 MODULE SPECIFICATIONS (see Figure 3 thru Figure 7 for operating characteristics)
MINIHAM MODULE SPECIFICATIONS (when used in accordance with Figure 1a)
Electrical Characteristics
Electrical characteristics apply over the full operating range of input voltage, output power and baseplate temperature, unless otherwise specified. All temperatures refer to the operating temperature at the center of the baseplate. Performance specifications are based on the ENMods system as shown in Figure 1a.
Parameter Min Typ Max Unit Notes
Output power 0 575 Watts Efficiency @115Vac 93 94 % Full load Efficiency @ 230Vac 96 97 % Full load Output voltage 250 375 Vdc External hold-up capacitance 3,300 µF
* Tracking error between BUS OK and Enable thresholds
ELECTROMAGNETIC COMPATIBILITY (configured as illustrated in Figures 1a and 1b)
Harmonic currents EN61000-3-2, Amendment 14 50-625W, 230Vac input 575W output (see Figure 2) Input line disturbances EN61000-4-11
Input surge withstand EN61000-4-5
2kV–50 µs common mode 1kV–50 µs differential mode
Conducted emissions EN55022, Level B (See Figures 8a thru 8c)
Page 3
Set your site on VICOR at www.vicorpower.com
PRELIMINARY
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 ENMods System: FARM3 and MiniHAM Rev. 1.3 Page 3 of 12
Electrical Characteristics (continued)
MODULE GENERAL SPECIFICATIONS
Parameter Min Typ Max Unit Notes
Safety approvals
FARM3 TÜV + VDE EN60950, CE Marked (pending)
MiniHAM CE Marked (pending) Isolation (in to out) None Isolation provided by DC-DC converter(s) Dielectric withstand (I/O to baseplates) 1500 Vrms Baseplate earthed Leakage current 2.5 mA 264Vac MTBF >1,000,000 Hours 25˚C, Ground Benign Baseplate material Aluminum Cover Dupont Zenite / Aluminum Pin material
–Style 1 & 2 Copper, Tin/Lead solder dipped
–Style S & N (ModuMate compatible) Copper, Nickel/Gold plating Weight
FARM3 3.1(88) Ounces (grams)
MiniHAM 5.1(145) Ounces (grams) Size 2.25 x 2.2 x 0.5 Inches Vicor’s standard mini half-brick package
57,9 x 55,9 x 12,7 mm
Storage temperature
(C-, T-Grade) -40 +125 °C
(H-Grade) -55 +125 °C
(M-Grade) -65 +125 °C Operating temperature
(C-Grade) -20 +100 °C Baseplate
(T-, H-Grade) -40 +100 °C Baseplate
(M-Grade) -55 +100 °C Baseplate
Figure 1a—ENMods system and DC-DC converter interconnection drawing
Holdup Box (HUB)
820µF HUB820-S 2200µF HUB2200-S
1200µF HUB1200-S 2700µF HUB2700-S 1800µF HUB1800-S 3300µF HUB3300-S
Part
C1,2 C3 – 6 C7,8 C9,C10 R1,2 R3 V1,2 V3 V5,V6 F1,2 D1,2 D3,D4
N
AC line Input
L PE
Description
Holdup capacitors 4700pF Film Cap., 0.8µF .001µF 150k, 0.5W 499, 0.125W MOV 220V 270V MOV BBS75 Gas Tube 3A, PC Tron Diode (1N4006) 1N5817
N
N
Filter
(Fig.1b)
L
L
Vicor Part Number
see text 01000
00127-1503
20461-220 03040 26107 02178 00670 26108
V5
N
V3
EMI GND
SR L
FARM3
+
C7
BOK
ST EN
C8
Sizing PCB traces:
All traces shown in bold carry significant current and should be sized accordingly.
N/+
V1
NC
NC
V2
L/–
MINI HAM
V6
N/+ NC
NC NC
L/–
R1R2C1
C2
R3
D1
D2
C10
To additional converters
C3
F1
C9
F2
+In
D3
PC (Gate In)
Vicor 300Vin
DC-DC
PR (Gate Out) –In
C4
C5
+In
D4
PC (Gate In)
PR (Gate Out) –In
C6
Converter
Vicor 300Vin
DC-DC
Converter
Page 4
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 ENMods System: FARM3 and MiniHAM Rev. 1.3 Page 4 of 12
Set your site on VICOR at www.vicorpower.com
PRELIMINARY
Figure 1b — Input EMI filter for EN55022, Level B compliance
Figure 2 — Measured harmonic current at 230VAC, 575W vs. EN spec limits
*Measured values of even harmonics are below 0.01A
Operating Characteristics
R1
Input
L3
L2/N
C2
L1
L1
PE
F1
V1
C1
L2
R2
R3
C3
Harmonic Current
10.00
R4
C4
Output
PE
Part
C1 C2, C3
N
L
C4 F1 F1 L1, L2 L3 R1, R2 R3 R4 V1
Description
1.0µF 4700pF
0.33µF
6.3A Fuse(5mm) Fuse Holder 27µH
1.3mH 10 150k, 0.5W
2.2, 2W MOV
Vicor Part Number
02573 01000 00927 22985 25318 14563 15016 00126-10R0 00127-1503 25896 03040
1.00
Odd Harmonic Limits
*
Even Harmonic Limits
Current (A)
0.10
0.01 2345678910111213141516171819202122232425262728293031323334353637383940
Measured Values
Harmonic Number
Page 5
Set your site on VICOR at www.vicorpower.com
PRELIMINARY
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 ENMods System: FARM3 and MiniHAM Rev. 1.3 Page 5 of 12
Operating Characteristics (FARM3)
Figure 3—Start-up at 120Vac input
Figure 5—Power-down from 120Vac Figure 6—Power-down from 240Vac
Figure 4—Start-up at 240Vac input
Vdc output
Strap Engaged
Iac input @2A / mV
Iac input @2A / mV
Enable
Enable
B OK
Vdc output
B OK
Vdc output
Enable
B OK
Vdc output
Enable
B OK
Figure 7—Output overvoltage protection 240Vac range
Vdc output
Enable
B OK
Page 6
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 ENMods System: FARM3 and MiniHAM Rev. 1.3 Page 6 of 12
Set your site on VICOR at www.vicorpower.com
PRELIMINARY
Operating Characteristics (Conducted emissions relative to EN55022 Reference Figure 1a)
Quasi Peak and Average Limits
Figure 8a —Peak detection
Figure 8c —Average detection
Figure 8b —Quasi peak detection
Page 7
Set your site on VICOR at www.vicorpower.com
PRELIMINARY
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 ENMods System: FARM3 and MiniHAM Rev. 1.3 Page 7 of 12
The ENMods system provides an effective solution for the AC front end of a power supply built with Vicor DC-DC converters. This high performance power system building block satisfies a broad spectrum of requirements and agency standards.
The ENMods system provides transient/surge immunity, harmonic current attenuation and EMI filtering, in addition to all of the power switching and control circuitry necessary for autoranging rectification, inrush current limiting, and overvoltage protection. Converter enable and status functions for orderly power up/down control or sequencing are also provided. To complete the AC front end configuration, the user only needs to add hold-up capacitors, a simple EMI filter, and a few discrete components (Fig 1A).
Functional Description (FARM3, see Figures 9 & 10)
Power-Up Sequence.
Upon application of input power, the hold-up capacitors begin to charge. The thermistor limits the charge current, and the exponential time constant is determined by the hold-up capacitor value and the thermistor cold resistance. The slope (dv/dt) of the capacitor voltage versus time approaches zero as the capacitors become charged to the peak of the AC line voltage.
The switch that bypasses the inrush limiting PTC (positive temperature coefficient) thermistor is open when power is applied, as is the switch that engages the strap for voltage doubling. In addition, the converter modules are disabled via the Enable (EN) line, and Bus-OK (BOK) is high.
If the bus voltage is less than 200V as the slope nears zero, the voltage doubler is activated, and the bus voltage climbs exponentially to twice the peak line voltage. If the bus voltage is greater than 200V, the doubler is not activated.
If the bus voltage is greater than 235V as the slope approaches zero, the inrush limiting thermistor is bypassed. Below 235V, it is not bypassed.
The converters are enabled 50 milliseconds after the thermistor bypass switch is closed.
Bus-OK is asserted after an additional 50 millisecond delay to allow the converter outputs to settle within specification.
Power-Down Sequence. When input power is turned off or fails, the following sequence occurs as the bus voltage decays:
Bus-OK is deasserted when the bus voltage falls below 210Vdc.
The converters are disabled when the bus voltage falls below 190Vdc. If power is reapplied after the converters are disabled, the entire power-up sequence is repeated. If a momentary power interruption occurs and power is reestablished before the bus reaches the disable threshold, the power-up sequence is not repeated, i.e., the power conversion system “rides through” the momentary interruption.
Application Note
Figure 9—Functional block diagram: FARM3 module Figure 10—Timing diagram: power-up/down sequence
1.1
2.1
3.1
4.1
5.1
1.2
2.2
Power
400 300 200 100
Up
1. 1
0
2.1
3.1
50ms
4.1
5.1
50ms
+Out
PTC
L
N
Thermistor
Microcontroller
Strap
Strap
–Out
SR
EN
BOK
90–132V
AC Line
Output
Bus
(Vdc)
Strap
PTC
Thermistor
Bypass
Converter
Enable
Bus OK
Power
Down
2.2
1.2
Page 8
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 ENMods System: FARM3 and MiniHAM Rev. 1.3 Page 8 of 12
Set your site on VICOR at www.vicorpower.com
PRELIMINARY
Application Note (continued) Off-Line Power Supply Configuration
The ENMods system maintains the DC output bus voltage between 250 and 370Vdc over the entire input voltage range, which is compatible with all Vicor 300V input converters. Autoranging automatically switches to the proper bridge or doubler mode at startup depending on the input voltage, eliminating the possibility of damage due to improper line connection. The ENMods system is rated at 575W output power. These modules can serve as the AC front end for any number and combination of compatible converters as long as the maximum power rating is not exceeded.
Pin Descriptions (see Figure 1a)
Strap (ST) Pin. In addition to input and output power pin
connections, it is necessary to connect the Strap pin to the center junction of the series hold-up capacitors (C1, C2) for proper (autoranging) operation. Varistors V1 and V2 provide capacitor protection. The bleeder resistors (R1, R2) discharge the hold-up capacitors when power is switched off. Capacitors C7 and C8 are recommended if the hold-up capacitors are located more than 3 inches from the output pins.
Enable (EN) Pin. The Enable pin must be connected to the PC or Gate-In pin of all converter modules to disable the converters during power-up. Otherwise, the converters would attempt to start while the hold-up capacitors are being charged through the current limiting thermistor, preventing the bus voltage from reaching the thermistor bypass threshold, thus disabling the power supply. The Enable output (the drain of an N channel MOSFET) is internally pulled up to 15V through a 150kresistor. (see Figure 11)
A signal diode should be placed close to and in series with the PC or (Gate-In) pin of each converter to eliminate the possibility of control interference between converters. The Enable pin switches to the high state (15V) with respect to the SR pin to turn on the converters after the power-up inrush is over. The Enable function also provides input overvoltage protection for the converters by turning off the converters if the DC bus voltage exceeds 400Vdc. The thermistor bypass switch opens if this condition occurs, placing the thermistor in series with the input voltage, which reduces the bus voltage to a safe level while limiting input current in case the varistors conduct. The thermistor bypass switch also opens if a fault or overload reduces the bus voltage to less than 180Vdc. (see Figure 9)
Bus-OK (BOK) Pin. (see Figure 12) The Bus-OK pin is intended to provide early-warning power fail information and is also referenced to the SR pin.
Caution: There is no input to output isolation in the ENMods. It is necessary to monitor Bus-OK via an optoisolator if it is to be used on the secondary (output) side of the converters. A line isolation transformer should be used when performing scope measurements. Scope probes should never be applied simultaneously to the input and output as this will destroy the unit.
L, N Pins. Line and neutral input. +, – Pins. Positive and negative outputs. SR Pin. Signal return for BOK and EN outputs
Filter (see Figure 1b)
The input EMI filter consists of differential and common mode chokes,Y– rated capacitors (line-ground) and X– rated capacitors (line-line). This filter configuration provides sufficient common mode and differential mode insertion loss in the frequency range between 100kHz and 30MHz to comply with the Level B conducted emissions limit, as illustrated in Figures 8a thru 8c.
Hold-up Capacitors
Hold-up capacitor values should be determined according to output bus voltage ripple, power fail hold-up time, and ride­through time (see Figure 13). Many applications require the power supply to maintain output regulation during a momentary power failure of specified duration, i.e., the converters must hold-up or ride through such an event while maintaining undisturbed output voltage regulation. Similarly, many of these same systems require notification of an impending power failure in order to allow time to perform an orderly shutdown.
The energy stored on a capacitor which has been charged to voltage V is:
ε= 1/2(CV
2
) (1)
Where: ε= stored energy
C = capacitance V = voltage across the capacitor
Energy is given up by the capacitors as they are discharged by the converters. The energy expended (the power-time product) is:
ε= P∆t = C(V
1
2
–V
2
2
) / 2 (2)
Where: P = operating power
t = discharge interval V
1
= capacitor voltage at the beginning of ∆t
V2= capacitor voltage at the end of ∆t
Rearranging Equation 2 to solve for the required capacitance:
C = 2Pt / (V
1
2
–V
2
2
) (3)
Page 9
Set your site on VICOR at www.vicorpower.com
PRELIMINARY
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 ENMods System: FARM3 and MiniHAM Rev. 1.3 Page 9 of 12
Figure 17—Converter ripple rejection vs. output voltage
Figure 14—Hold-up time vs. operating power and total bus
capacitance, series combination of C1, C2 (see Figure 1a)
Figure 16—Ripple voltage vs. operating power and bus capacitance, series combination of C1, C2 (see Figure 1a)
Figure 15—Ride-through time vs. operating power
Figure 13—Hold-up time
Application Note (continued)
Figure 12—Bus OK (BOK) isolated power status indicator
Figure 11—Enable (EN) function
N
EMI GND
SR
L
Micro-
controller
150k
FARM3
15Vdc
B OK
N
EMI GND
SR
Micro-
controller
L
ST EN
+
27k
15 Vdc
+
BOK
ST EN
+In
PC (Gate In)
PR (Gate Out)
–In
+5 Vdc
Secondary referenced
Vicor DC-DC
Converter
100
90 80 70 60 50 40 30 20
Ride-through Time (ms)
10
0
250
Total
capacitance
820µF
90Vac 115Vac
Operating Power (W)
30
1100µF
25
820µF 680µF
*
2200µF1600µF1300µF
500
FARM3
Ripple (V p-p)
πθθ
Power
Fail
Hold-up Time
Ride-Thru Time
B OK
Power Fail
Warning
Converter Shutdown
254V 205V
185V
40
*
2200µF1600µF1300µF
680µF
35
30
25
20
15
10
Power Fail Warning (ms)
5
0
250
Operating Power (W)
1100µF
820µF
500
20
*
15
10
P-P Ripple Volts (V)
5
0
Operating Power (W)
80
75
70
65
60
55
50
Ripple Rejection (dB)
*
45
40
Output Voltage
500250
50301552
Page 10
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 ENMods System: FARM3 and MiniHAM Rev. 1.3 Page 10 of 12
Set your site on VICOR at www.vicorpower.com
PRELIMINARY
Calculated values of bus capacitance for various hold-up time, ride-through time, and ripple voltage requirements are given as a function of operating power level in Figures 14, 15, and 16, respectively.
Example
In this example, the output required from the DC-DC converter at the point of load is 12Vdc at 320W. Therefore, the output power from the ENMods would be 375W (assuming a converter efficiency of 85%). The desired hold-up time is 9ms over an input range of 90 to 264Vac.
Determining Required Capacitance for Power Fail Warning. Figure 14 is used to determine capacitance for a
given power fail warning time and power level, and shows that the total bus capacitance should be at least 820µF. Since two capacitors are used in series, each capacitor should be at least 1,640µF. Note that warning time is not dependent on line voltage. A hold-up capacitor calculator is available on the Vicor website, at vicorpower.com.
Determining Ride-through Time. Figure 15 illustrates ride­through time as a function of line voltage and output power, and shows that at a nominal line of 90Vac, ride-through would be 68ms. Ride-through time is a function of line voltage.
Determining Ripple Voltage on the Hold-up Capacitors.
Figure 16 is used to determine ripple voltage as a function of operating power and bus capacitance, and shows that the ripple voltage across the hold-up capacitors will be 12V p-p.
Determining the Ripple on the Output of the DC-DC Converter. Figure 17 is used to determine the ripple
rejection of the DC-DC converter and indicates a ripple rejection of approximately 60 dB for a 12V output. Since the ripple on the bus voltage is 12Vac and the ripple rejection of the converter is 60 dB, the output ripple of the converter due to ripple on its input (primarily 120 Hz) will be 12mV p-p. Note that 2nd Generation converters have greater ripple rejection then either VI-200s or VI-J00s.
A variety of hold-up capacitor assemblies (HUBs) are available. Please visit the Vicor website @ vicorpower.com.
For more information about designing an autoranging AC input power supply using the ENMods and Vicor DC-DC converter modules, contact Vicor Applications Engineering at the nearest Vicor Technical Support Center, or send E-mail to apps@vicorpower.com.
• • •
The power fail warning time (t) is defined as the interval between BOK and converter shutdown (EN) as illustrated in Figure 13. The Bus-OK and Enable thresholds are 205V and 185V, respectively. A simplified relationship between hold-up time, operating power, and bus capacitance is obtained by inserting these constants in equation (3):
C = 2Pt / (205
2
– 1852)
C = 2Pt / (7,800)
It should be noted that the series combination (C1, C2, see Figure 1a) requires each capacitor to be twice the calculated value, but the required voltage rating of each capacitor is reduced to 200V.
Allowable ripple voltage on the bus (or ripple current in the capacitors) may define the capacitance requirement. Consideration should be given to converter ripple rejection and resulting output ripple voltage. The ripple rejection (R) of Vicor converters is specified as a function of the input/output voltage ratio:
R = 30 + 20log(Vin / Vout) (4)
For example, a converter whose output is 15V and nominal input is 300V will provide 56dB ripple rejection, i.e., 10V p-p of input ripple will produce 15mV p-p of output ripple (see Figure 17). Equation 3 is again used to determine the required capacitance. In this case, V
1
and V2are the instantaneous values of bus voltage at the peaks and valleys (see Figure 13) of the ripple, respectively. The capacitors must holdup the bus voltage for the time interval (t) between peaks of the rectified line as given by:
t = (π θ) / 2πf (5)
Where: f = line frequency
θ = rectifier conduction angle
The approximate conduction angle is given by:
θ = Cos
-1
(V
2/V1
) (6)
Another consideration in hold-up capacitor selection is their ripple current rating. The capacitors’ rating must be higher than the maximum operating ripple current. The approximate operating ripple current (rms) is given by:
Irms = 2P/Vac (7)
Where: P = total output power
Vac = operating line voltage
Application Note (continued)
Page 11
Set your site on VICOR at www.vicorpower.com
PRELIMINARY
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 ENMods System: FARM3 and MiniHAM Rev. 1.3 Page 11 of 12
PCB Mounting Specifications
Mechanical Diagram
(2X)
0.01
0.35 8,8
0.12 3,1
DIA,(7X)
0.150 3,81
(REF)
DIA,(2X)
0.080
2,03
431
98276 5
0.23 5,8
0.400
10,16
1.400 35,56
1.000 25,40
0.700 17,78
2.20 55,9
1.74 44,2
1.900 48,26
0.300 ±0.015
7,62±0,38
0.300±0.015 7,62±0,38
FULL R (6X)
(6X)
(REF.)
0.10 2,5
2.000 50,80
1.30 33,0
2.28 57,9
2.20 55,9
0.130
3,30
0.10 2,5
0.49 12,4
0.65 16,5
0.06 1,5
R (3X)
12
X 45˚
CHAMFER
Use a 4-40 Screw (6X)
Torque to:
5 in-lbs
0.57 N-m
0.54 13,7
0.42 10,6
Pin Style 2 &N
(Long)
0.62 15,7
Pin Style 1&S
(Short )
(9X)
(9X)
0.50 ±0.02 12,7 ±0,5
Slotted (Style 1) or Threaded (Style 2)
4-40 UNC-2B (6X)
or Thru Hole (Style 3)
#30 Drill Thru (6X) (0.1285)
FARM3 MiniHAM
Pin No. Function Label Function Label
1 Neutral N Neutral /+ In N/+ 2 EMI GND NC NC 3 Signal Return SR NC NC 4 Line L Line /– In L/– 5 –Out Line /– Out L /– 6 Enable EN NC NC 7 Strap ST NC NC 8 BUS OK BOK NC NC 9 +Out + Neutral /+ Out N/+
INBOARD
SOLDER
MOUNT
(7X)
(2X)
PIN STYLE 1
0.094 ±0.003 2,39 ±0,08
0.164 ±0.003 4,16 ±0,08
0.43 10,9
PCB THICKNESS
0.06
R (4X)
1,5
1.900*
1.900*
48.26
48,26
0.400* 10,16
0.195 4,95
0.062 ±0.010 1,57 ±0,25
1.790 45,47
12 34
0.700* 17,78
1.000* 25,40
1.400* 35,56
PLATED
THRU HOLE
DIA
56789
* DENOTES TOL =
Note: Pin styles S & N require use of ModuMate interconnection socketing systems. See SurfMate or InMate Design guides for PCB specifications.
1.584* 40,23
±0.003
±0,08
0.158 4,01
ONBOARD
SOLDER
MOUNT
PIN STYLE 2
0.094 ±0.003 2,39 ±0,08
0.164 ±0.003 4,16 ±0,08
0.53 13,5
ALUMINUM
BASEPLATE
ALL MARKINGS THIS SURFACE
Page 12
Vicor Corp. Tel: 800-735-6200, 978-470-2900 Fax: 978-475-6715 ENMods System: FARM3 and MiniHAM P/N 25260 Rev. 1.3 04/03/10M
Set your site on VICOR at www.vicorpower.com
Vicor’s comprehensive line of power solutions includes modular, high density DC-DC converters and accessory components, configurable power supplies, and custom power systems.
Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by Vicor for its use. No license is granted by implication or otherwise under any patent or patent rights of Vicor. Vicor components are not designed to be used in applications, such as life support systems, wherein a failure or malfunction could result in injury or death. All sales are subject to Vicor’s Terms and Conditions of Sale, which are available upon request.
Specifications are subject to change without notice.
Vicor Corporation
25 Frontage Road
Andover, MA, USA 01810
Tel: 800-735-6200
Fax: 978-475-6715
Email
Vicor Express: vicorexp@vicr.com Technical Support: apps@vicr.com
Component Solutions for Your Power System
45
Loading...