Datasheet EMIF6-100FC Datasheet (Protekdevices)

Page 1
05190
Only One Name Means ProTek’Tion™
APPLICATIONS
Cellular PhonesNotebooksPersonal Digital Assistant (PDA)Ground Positioning System (GPS)SMART Cards
IEC COMPATIBILITY (EN61000-4)
61000-4-2 (ESD): Air - 15kV, Contact - 8kV61000-4-4 (EFT): 40A - 5/50ns
FEATURES
ESD Protection > 25 kilovoltsBidirectional EMI Filtering/TVS Low Pass FiltersLow Insertion Loss: -3db Roll-Off @ 60MHzProtects Up to Six(6) Data Lines
EMIF6-100FC
EMI FILTER/TVS ARRAY
MECHANICAL CHARACTERISTICS
Flip Chip PackageWeight 0.73 milligrams (Approximate)Flammability rating UL 94V-08mm Tape and Reel Per EIA Standard 481
PIN CONFIGURATION
G1 G2 G3
105190.R1 9/03 www.protekdevices.com
Page 2
DEVICE CHARACTERISTICS
MAXIMUM RATINGS @ 25°C Unless Otherwise Specified
EMIF6-100FC
PARAMETER Operating Temperature Storage Temperature
SYMBOL VALUE
T
J
T
STG
-40°C to 85°C
-55°C to 150°C DC Power Per Resistor mW100P Typical Resistance @ ± 20% OHMS100R
ELECTRICAL CHARACTERISTICS PER LINE @ 25°C Unless Otherwise Specified
PA RT
NUMBER
EMIF6-100FC 6.0 0.1 0.8
Note 1: ±20% tolerance.
RATED
STAND-OFF
VOLTAGE
V
WM
VOLTS
5.0
MINIMUM
BREAKDOWN
VOLTAGE
@ 1mA
V
(BR)
VOLTS
MAXIMUM REVERSE
LEAKAGE
CURRENT
@ 3V
I
D
µA
TYPICAL
FORWARD
VOLTAGE
@10mA
V
F
VOLTS
MINIMUM
ATTENUATION
@
800-3000 MHz
dB
30
CUT-OFF
FREQUENCY
(50 Ohms I/O
ZERO BIAS)
fc
MHz
60
UNITS
°C
TYPICAL
CAPACITANCE
PER LINE
(See Note 1)
@2.5V, 1 MHz
C
pF 54
RESISTANCE VS TEMPERATURE
1.100
1.060
1.020
0.980
Normalized Resistance
0.940
0.900
-40 -20 0 20 40 60 80 100
(Normalized to Resistance at 25°C)
FIGURE 1
Temperature °C
2 www.protekdevices.com05190.R1 9/03
Page 3
GRAPHS
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
0.1 1 10 100 1000 10000
EMIF6-100FC
INSERTION LOSS - EMIF6-100FC
FIGURE 2
2.5 Volts
Gain (dB)
0 Volts
Frequency (MHz)
FIGURE 3
OVERSHOOT & CLAMPING VOLTAGE FOR EMIF6-100FC
35
25
15
5 Volts per Division
-5
1 Volts per Division
5
ESD Test Pulse: +15 kilovolt, 1/30ns (waveform)
FIGURE 4
OVERSHOOT & CLAMPING VOLTAGE FOR EMIF6-100FC
4
2
0
-2
-4
ESD Test Pulse: -15 kilovolt, 1/30ns (waveform)
3 www.protekdevices.com05190.R1 9/03
Page 4
APPLICATION INFORMATION
PRINTED CIRCUIT BOARD RECOMMENDATIONS
EMIF6-100FC
PARAMETER
Pad Size on PCB Pad Shape Pad Definition Solder Mask Opening Solder Stencil Thickness Solder Stencil Aperture Opening (laser cut, 5% tapered walls) Solder Flux Ratio Solder Paste Type Pad Protective Finish Tolerance - Edge To Corner Ball Solder Ball Side Coplanarity Maximum Dwell Time Above Liquidous (183°C) Soldering Maximum Temperature
FIGURE 5
RECOMMENDED NON-SOLDER MASK DEFINED PAD ILLUSTRATION
Non-Solder Mask Defined Pad
0.275mm DIA.
Solder Mask Opening
0.325mm DIA.
VALUE
0.275mm Round Non-Solder Mask Defined Pads
0.325mm Round
0.150mm
0.330mm Round 50/50 By Volume No Clean OSP(Entek Cu Plus 106A) ±50µm ±20µm 60 Seconds 240°C
Solder Stencil Opening
0.330mm DIA.
200°C
100°C
Instantaneous
to 200°C
1-2 Minutes
to 150°C
4 www.protekdevices.com05190.R1 9/03
SOLDER REFLOW PROFILE
Pre-Heat
Time
FIGURE 6
225°C
5-10 sec
1-2 Minutes to 25°C
Soldering
Time
Note: This reflow profile does not take into account the printed circuit board (PCB) material heating time. Additional time may be required for the preheat time and cool down time upon the PCB or board material.
Cool Down
Time
Page 5
PACKAGE OUTLINE & DIMENSIONS
EMIF6-100FC
G
O
G
I
0.30 DIA. 63/37 Sn/Pb Solder Bumps
PACKAGE OUTLINE
PACKAGE DIMENSIONS
MILLIMETERS
BOTTOM VIEW
A
C
D
E
123456
DIM
A
SIDE VIEW
B
C
F
B
H
D
E
F G H
I
J
J
NOTE:
1. Controlling dimensions in millimeters.
I
MIN MINMAX
2.915
1.285
0.495
0.245
0.430
0.430
0.180
0.180
0.432
0.330
3.005
1.375
0.505
0.255
0.440
0.440
0.280
0.280
0.559
0.457
TAPE & REEL SPECIFICATIONS
PART NUMBER CHIP S IZE ( mm)
EMIF6-100FC 2.96 x 1.33 x 0.6 ± 0.05 3.18 x 1.52 x 0.76 ±0.1 8mm 7 3,000 4mm 4mm
POCKET SIZE (mm)
x A0 x K
B
0
0
TAPE WIDTHWREEL
DIAMETER
QTY PER
REEL
P
0
0.1148
0.0506
0.0195
0.0096
0.0169
0.0169
0.0071
0.0071
0.017
0.013
P
1
INCHES
MAX
0.1183
0.0541
0.0199
0.0100
0.0173
0.0173
0.0110
0.0110
0.022
0.018
Top Cover Tape
K
0
For Tape Feeder Reference Only Including Draft Concentric Around B
TAPE & REEL ORDERING NOMENCLATURE
1. Surface mount product is taped and reeled in accordance with EIA-481.
2. Plastic 8mm Tape: Suffix-T73-1 = 7 Inch Reel - 3,000 pieces per reel, i.e.,
COPYRIGHT © ProTek Devices 2003
SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except JEDEC).
DESIGN CHANGES: ProTek reser ves the right to discontinue product lines without notice, and that the final judgement concerning selection and specifications is the buyer’s and that in furnishing engineering and technical assistance, ProTek assumes no responsibility with respect to the selection or specifications of such products.
Embossment
A
0
B
0
P
1
EMIF6-100FC-T73-1.
5 www.protekdevices.com05190.R1 9/03
P
0
10 Pitches Cumulative Tolerance On Tape ±0.2mm
W
Direction of Feed
Outline & Dimensions: Rev 0 - 8/03, 06042
ProTek Devices
2929 South Fair Lane, Tempe, AZ 85282 Tel: 602-431-8101 Fax: 602-431-2288 E-Mail: sales@protekdevices.com Web Site: www.protekdevices.com
Loading...