Datasheet EL5396CU-T13, EL5396CU, EL5396CS-T13, EL5396CS Datasheet (ELANT)

Page 1
EL5396C - Preliminary
Triple 400MHz Fixed Gain Amplifier
EL5396C - Preliminary
Features
• Gain selectable (+1, -1, +2)
• 400MHz -3dB Bandwidth (AV = 1,
2)
• 9mA supply current (per amplifier)
• Single and dual supply operation, from 5V to 10V
• Power-down
• Available in 16-pin QSOP package
• Single (EL5196C) available
• 200MHz, 3mA product available (EL5197C, EL5397C)
Applications
• Video Amplifiers
• Cable Drivers
• RGB Amplifiers
• Test Equipment
• Instrumentation
• Current to Voltage Converters
Ordering Information
Part No Package
EL5396CS 16-Pin SO - MDP0027
EL5396CS-T7 16-Pin SO 7” MDP0027
EL5396CS-T13 16-Pin SO 13” MDP0027
EL5396CU 16-Pin QSOP - MDP0040
EL5396CU-T13 16-Pin QSOP 13” MDP0040
Tape &
Reel Outline #
General Description
The EL5396C is a triple channel, fixed gain amplifier with a band­width of 400MHz, making these amplifiers ideal for today’s high speed video and monitor applications. The EL5396C features internal gain setting resistors and can be configured in a gain of +1, -1 or +2. The same bandwidth is seen in both gain-of-1 and gain-of-2 applications.
The EL5396C can be run from a single or dual supply voltage of 5V to 10V and consumes just 9mA of supply current per channel. Each channel of the EL5396C has a disable. Upon being disabled, the out­puts are tri-stated and the power supply current reduces to less than 150µA per amplifier. Allowing the CE pin to float, or applying a low logic level will enable the amplifier.
For applications where board space is critical, the EL5396C is offered in the 16-pin QSOP package, as well as a 16-pin SO. The EL5396C is specified for operation over the full industrial temperature range of ---
-40°C to +85°C.
Pin Configurations
16-Pin SO & QSOP
INA+
CEA
VS-
CEB
INB+
1
2
-
+
3
+
4
-
5
16
INA-
15
OUTA
14
VS+
13
OUTB
12
INB-
6
NC
+
7
CEC
INC+
Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a “controlled document”. Current revisions, if any, to these specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
© 2001 Elantec Semiconductor, Inc.
-
8 9
EL5396CS, EL5396CU
11
NC
10
OUTC
INC-
September 19, 2001
Page 2
EL5396C - Preliminary
Triple 400MHz Fixed Gain Amplifier
Absolute Maximum Ratings (T
Values beyond absolute maximum ratings can cause the device to be pre­maturely damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied.
Supply Voltage between VS+ and VS- 11V
EL5396C - Preliminary
Maximum Continuous Output Current 50mA
Operating Junction Temperature 125°C
= 25°C)
A
Power Dissipation See Curves
Pin Voltages VS- - 0.5V to VS+ +0.5V
Storage Temperature -65°C to +150°C
Operating Temperature -40°C to +85°C
Lead Temperature 260°C
Important Note:
All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA.
Electrical Characteristics
VS+ = +5V, VS- = -5V, R
Parameter Description Conditions Min Typ Max Unit
AC Performance
BW -3dB Bandwidth AV = +1 400 MHz
BW1 0.1dB Bandwidth 35 MHz
SR Slew Rate VO = -2.5V to +2.5V, AV = +2 TBD -2600 V/µs
ts 0.1% Settling Time V
C
S
e
n
i
- IN- input current noise 25 pA/Hz
n
i
+ IN+ input current noise 55 pA/Hz
n
dG Differential Gain Error
dP Differential Phase Error
DC Performance
V
OS
TCV
OS
A
E
RF, R
G
Input Characteristics
CMIR Common Mode Input Range ±3V ±3.3V V
+I
IN
-I
IN
R
IN
C
IN
Output Characteristics
V
O
I
OUT
Enable (selected packages only)
t
EN
t
DIS
I
IHCE
I
ILCE
V
IHCE
V
ILCE
= 150, T
L
= 25°C unless otherwise specified.
A
AV = +2 400 MHz
= -2.5V to +2.5V, AV = -1 9 ns
OUT
Channel Separation f = 5MHz 68 dB Input Voltage Noise 3.8 nV/Hz
[1]
[1]
AV = +2 0.035 %
AV = +2 0.04 °
Offset Voltage -15 1 15 mV
Input Offset Voltage Temperature Coefficient Measured from T
MIN
to T
MAX
5 µV/°C
Gain Error VO = -3V to +3V -2 1.3 2 %
Internal RF and R
G
320 400 480
+ Input Current -120 40 120 µA
- Input Current -40 4 40 µA Input Resistance 27 k
Input Capacitance 0.5 pF
Output Voltage Swing R
Output Current R
= 150Ω to GND ±3.4V ±3.7V V
L
R
= 1KΩ to GND ±3.8V ±4.0V V
L
= 10 to GND 95 120 mA
L
Enable Time 40 ns
Disable Time TBD ns
CE pin Input High Current CE = VS+ 0.8 6 µA
CE pin Input Low Current CE = VS- 0 -0.1 µA
CE pin Input High Voltage for Power Down VS+ -0.5 V
CE pin Input Low Voltage for Power Up VS+ -3 V
2
Page 3
EL5396C - Preliminary
Triple 400MHz Fixed Gain Amplifier
Electrical Characteristics
VS+ = +5V, VS- = -5V, R
Parameter Description Conditions Min Typ Max Unit
Supply
Is
ON
Is
OFF
PSRR Power Supply Rejection Ratio DC, VS = ±4.75V to ±5.25V 55 75 dB
-IPSR - Input Current Power Supply Rejection DC, VS = ±4.75V to ±5.25V -2 2 µA/V
1. Standard NTSC test, AC signal amplitude = 286mV
= 150, T
L
Supply Current - Enabled (per amplifier) No Load, V
Supply Current - Disabled (per amplifier) No Load, VIN = 0V, CE = +4.5V 95 130 µA
= 25°C unless otherwise specified.
A
, f = 3.58MHz
P-P
= 0V, CE = -5V 8 9 10.5 mA
IN
EL5396C - Preliminary
3
Page 4
EL5396C - Preliminary
Triple 400MHz Fixed Gain Amplifier
Typical Performance Curves
EL5396C - Preliminary
Non-Inverting Frequency Response (Gain)
6
AV=1
2
-2
-6
Normalized Magnitude (dB)
-10 RF=750
RL=150
-14
1M 10M 100M 1G
Inverting Frequency Response (Gain)
6
2
-2
-6
Normalized Magnitude (dB)
-10 RF=500
RL=150
-14
1M 10M 100M 1G
AV=5
AV=10
Frequency (Hz)
AV=-1
AV=-3
Frequency (Hz)
AV=2
AV=-2
Non-Inverting Frequency Response (Phase)
90
0
-90
Phase (°)
-180
-270 RF=750
RL=150
-360
1M 10M 100M 1G
Inverting Frequency Response (Phase)
90
0
-90
Phase (°)
-180
-270 RF=500
RL=150
-360
1M 10M 100M 1G
AV=5
AV=10
Frequency (Hz)
AV=-2
AV=-3
Frequency (Hz)
AV=1
AV=2
AV=-1
Frequency Response for Various CIN-
10
6
2
-2
Normalized Magnitude (dB)
AV=2
-6 RF=500
RL=150
-10 1M 10M 100M 1G
2pF added
0pF added
Frequency (Hz)
1pF added
Frequency Response for Various R
6
2
-2
-6
Normalized Magnitude (dB)
-10
AV=2 RF=500
-14 1M 10M 100M 1G
Frequency (Hz)
RL=100
RL=500
L
RL=150
4
Page 5
Typical Performance Curves
EL5396C - Preliminary
EL5396C - Preliminary
Triple 400MHz Fixed Gain Amplifier
Frequency Response for Various C
14
AV=2 RL=150
10
RF=RG=500
6
2
Normalized Magnitude (dB)
-2
-6 1M 10M 100M 1G
Group Delay vs Frequency
3.5
3
2.5
2
1.5
Delay (ns)
1
0.5
0 1M 10M 100M 1G
33pF
8pF 0pF
Frequency (Hz)
AV=2
RF=500
AV=1
RF=750
Frequency (Hz)
L
22pF
15pF
Frequency Response for Various R
6
2
-2
-6
Normalized Magnitude (dB)
AV=2
-10 RG=R
F
RL=150
-14
1M 10M 100M 1G
Frequency (Hz)
Frequency Response for Various Common-mode Input Voltages
6
2
-2
-6
Normalized Magnitude (dB)
AV=2
-10 RF=500
RL=150
-14
1M 10M 100M 1G
Frequency (Hz)
F
340 475
750
1.2k
VCM=3V VCM=0V
VCM=-3V
620
Transimpedance (ROL) vs Frequency
10M
1M
100k
10k
Magnitude ()
1k
100
1k
10k 100k 1M 10M 100 1G
Phase
Gain
Frequency (Hz)
0
-90
-180
-270
-360
PSRR and CMRR vs Frequency
20
0
-20
Phase (°)
-40
PSRR/CMRR (dB)
-60
-80
10k 100k 1M 10M 1G100M
PSRR-
Frequency (Hz)
PSRR+
CMRR
5
Page 6
EL5396C - Preliminary
Triple 400MHz Fixed Gain Amplifier
Typical Performance Curves
EL5396C - Preliminary
-3dB Bandwidth vs Supply Voltage for Non-inverting Gains
400
RF=750
350
RL=150
300 250 200 150
-3dB Bandwidth (MHz) 100
50
0
5 6 9 10
Peaking vs Supply Voltage for Non-inverting Gains
4
3.5 3
2.5 2
Peaking (dB)
1.5 1
0.5 0
5 6 9 107 8
7 8
Total Supply Voltage (V)
AV=1
AV=2
AV=10
Total Supply Voltage (V)
AV=1
AV=2
AV=5
AV=10
RF=750 RL=150
-3dB Bandwidth vs Supply Voltage for Inverting Gains
250
200
150
100
-3dB Bandwidth (MHz) 50
RF=500 RL=150
0
5 6 9 107 8
Peaking vs Supply Voltage for Inverting Gains
2.5
2
1.5
1
Peaking (dB)
0.5
0
5 6 9 107 8
AV=-1
AV=-2
AV=-5
Total Supply Voltage (V)
Total Supply Voltage (V)
AV=-1
AV=-2
RF=500 RL=150
Non-inverting Frequency Response (Gain)
6
2
-2
-6
Normalized Magnitude (dB)
-10 RF=750
RL=150
-14
1M 10M 100M 1G
AV=5
AV=10
Frequency (Hz)
AV=1
AV=2
Non-inverting Frequency Response (Phase)
90
0
-90
Phase (°)
-180
-270 RF=750
RL=150
-360
1M 10M 100M 1G
AV=1 AV=2
AV=5
AV=10
Frequency (Hz)
6
Page 7
Typical Performance Curves
EL5396C - Preliminary
EL5396C - Preliminary
Triple 400MHz Fixed Gain Amplifier
Inverting Frequency Response (Gain)
6
2
-2 AV=-5
-6
Normalized Magnitude (dB)
-10 RF=500
RL=150
-14
1M 10M 100M 1G
Frequency (Hz)
-3dB Bandwidth vs Temperature for Non-inverting Gains
500
400
300
200
-3dB Bandwidth (MHz) 100
0
-40 10 110 160
AV=2
AV=5
AV=10
AV=1
60
Ambient Temperature (°C)
AV=-1
AV=-2
RF=750 RL=150
Inverting Frequency Response (Phase)
90
0
-90
Phase (°)
-180
-270 RF=500
RL=150
-360
1M 10M 100M 1G
-3dB Bandwidth vs Temperature for Inverting Gains
250
200
150
100
-3dB Bandwidth (MHz) 50
0
-40 10 110 160
AV=-1
AV=-2
AV=-5
AV=-1 AV=-2
AV=-5
Frequency (Hz)
60
Ambient Temperature (°C)
RF=500 RL=150
Peaking vs Temperature
2.5 RL=150
2
1.5
1
Peaking (dB)
0.5
0
-0.5
-40 10 110 160
AV=1
AV=-1
60
Ambient Temperature (°C)
Voltage and Current Noise vs Frequency
1000
100
10
Voltage Noise (nV/Hz)
, Current Noise (pA/Hz)
1
100
in+
in-
e
n
1000 10k 100k 10M1M
Frequency ()
7
Page 8
EL5396C - Preliminary
Triple 400MHz Fixed Gain Amplifier
Typical Performance Curves
EL5396C - Preliminary
Closed Loop Output Impedance vs Frequency
100
10
1
0.1
Output Impedance ()
0.01
0.001
Frequency (Hz)
2nd and 3rd Harmonic Distortion vs Frequency
-20 AV=+2
-30
V
=2V
OUT
P-P
RL=100
-40
-50
-60
-70
Harmonic Distortion (dBc)
-80
-90
1
2nd Order Distortion
Frequency (MHz)
3rd Order Distortion
10 100
Supply Current vs Supply Voltage
10
8
6
4
Supply Current (mA)
2
0
0
Two-tone 3rd Order Input Referred Intermodulation Intercept (IIP3)
25
AV=+2
20
RL=150
15
10
5
0
Input Power Intercept (dBm)
-10
AV=+2
-5
RL=100
10
Supply Voltage (V)
Frequency (MHz)
122 10864100 1k 100M 1G1M100k 10M10k
100
Differential Gain/Phase vs DC Input Voltage at 3.58MHz
0.03 AV=2
0.02
RF=RG=500 RL=150
0.01
0
-0.01
-0.02
dG (%) or dP (°)
-0.03
-0.04
-0.05
-1 -0.5 0 0.5 1 DC Input Voltage
dP
dG
Differential Gain/Phase vs DC Input Voltage at 3.58MHz
0.04 AV=1
0.03
RF=750 RL=500
0.02
0.01
0
-0.01
dG (%) or dP (°)
-0.02
-0.03
-0.04
-1 -0.5 0 0.5 1 DC Input Voltage
dP
dG
8
Page 9
Typical Performance Curves
EL5396C - Preliminary
EL5396C - Preliminary
Triple 400MHz Fixed Gain Amplifier
)
PP
Output Voltage Swing (V
200mV/div
Output Voltage Swing vs Frequency THD<1%
10
RL=500
8
RL=150
6
4
2
AV=2 AV=2
0
1
Small Signal Step Response Large Signal Step Response
10 100
Frequency (MHz)
VS=±5V RL=150 AV=2 RF=RG=500
Output Voltage Swing vs Frequency THD<0.1%
10
)
8
PP
Output Voltage Swing (V
1V/div
RL=500
6
RL=150
4
2
0
1
10 100
Frequency (MHz)
VS=±5V RL=150 AV=2 RF=RG=500
10ns/div
Settling Time vs Settling Accuracy
25
20
15
10
Settling Time (ns)
5
0
0.01 0.1 1 Settling Accuracy (%)
AV=2 RF=RG=500 RL=150 V
STEP
=5V
P-P
output
10ns/div
Transimpedance (RoI) vs Temperature
625
600
575
RoI (k)
550
525
-40 10 60 110 160 Die Temperature (°C)
9
Page 10
EL5396C - Preliminary
Triple 400MHz Fixed Gain Amplifier
Typical Performance Curves
EL5396C - Preliminary
PSRR and CMRR vs Temperature
90 80 70 60 50 40
PSRR/CMRR (dB)
30 20 10
-40 10 60 110 160 Die Temperature (°C)
Offset Voltage vs Temperature
2
1
0
(mV)
OS
V
-1
-2
-40 10 60 110 160 Die Temperature (°C)
PSRR
CMRR
ICMR and IPSR vs Temperature
2
1.5
1
0.5
ICMR/IPSR (µA/V)
0
-0.5
-40 10 60 110 160
60
40
20
0
-20
Input Current (µA)
-40
-60
-40 10 110 160
ICMR+
IPSR
ICMR-
Die Temperature (°C)
Input Current vs Temperature
60
Temperature (°C)
IB-
IB+
Positive Input Resistance vs Temperature
60
50
40
30
+ (k)
IN
R
20
10
0
-40 10 110 160
60
Temperature (°C)
Supply Current vs Temperature
5
4
3
2
Supply Current (mA)
1
0
-40 10 110 160
60
Temperature (°C)
10
Page 11
Typical Performance Curves
EL5396C - Preliminary
EL5396C - Preliminary
Triple 400MHz Fixed Gain Amplifier
Positive Output Swing vs Temperature for Various Loads
4.2
4.1
4
3.9
(V)
OUT
3.8
V
3.7
3.6
3.5
-40 10 110 160
130
125
(mA)
OUT
I
120
115
-40 10 60 110 160
1k
150
60
Temperature (°C)
Output Current vs Temperature
Sink
Source
Die Temperature (°C)
Negative Output Swing vs Temperature for Various Loads
-3.5
-3.6
-3.7
-3.8
(V)
OUT
-3.9
V
-4
-4.1
-4.2
-40 10 110 160 Temperature (°C)
Slew Rate vs Temperature
4000
3500
3000
Slew Rate (V/µS)
2500
-40 10 60 110 160
Die Temperature (°C)
150
1k
60
AV=2 RF=RG=500 RL=150
Channel-to-Channel Isolation vs Frequency
0
-20
-40
Gain (dB)
-60
-80
-100 100k 1M 10M 100M
Frequency (Hz)
400M
Package Power Dissipation vs Ambient Temp.
JEDEC JESD51-3 Low Effective Thermal Conductivity Test Board
1
0.9 909mW
0.8
0.7
0.6
633mW
0.5
0.4
0.3
Power Dissipation (W)
0.2
0.1
0
0 50 100 150
S
O
1
1
6
1
0
°
C
/
W
Q
S
O
P
1
1
6
5
8
°
C
/
W
25 75 125
Ambient Temperature (°C)
11
Page 12
EL5396C - Preliminary
Triple 400MHz Fixed Gain Amplifier
Pin Descriptions
EL5396C
16-Pin SO & 16-
Pin QSOP Pin Name Function Equivalent Circuit
EL5396C - Preliminary
1 INA+ Non-inverting input, Channel A
2 CEA Amplifier A enable
CE
3 VS- Negative supply
4 CEB Amplifier B enable (Reference Circuit 2)
5 INB+ Non-inverting input, Channel B (Reference Circuit 1)
6 NC Not connected
7 CEC Amplifier C enable (Reference Circuit 2)
8 INC+ Non-inverting input, Channel C (Reference Circuit 1)
9 INC- Inverting input, Channel C (Reference Circuit 1)
10 OUTC Output, Channel C
Circuit1
Circuit 2
R
G
R
F
IN-IN+
11 NC Not connected
12 INB- Inverting input, Channel B (Reference Circuit 1)
13 OUTB Output, Channel B (Reference Circuit 3)
14 VS+ Positive supply
15 OUTA Output, Channel A (Reference Circuit 3)
16 INA- Inverting input, Channel A (Reference Circuit 1)
12
Circuit 3
OUT
R
F
Page 13
EL5396C - Preliminary
Triple 400MHz Fixed Gain Amplifier
EL5396C - Preliminary
General Disclaimer
Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the cir­cuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any circuits described herein and makes no representations that they are free from patent infringement.
WARNING - Life Support Policy
Elantec, Inc. products are not authorized for and should not be used within Life Support Systems without the specific written consent of Elantec, Inc. Life Support systems are equipment intended to sup-
Elantec Semiconductor, Inc.
675 Trade Zone Blvd. Milpitas, CA 95035 Telephone: (408) 945-1323
(888) ELANTEC Fax: (408) 945-9305 European Office: +44-118-977-6020 Japan Technical Center: +81-45-682-5820
port or sustain life and whose failure to perform when properly used in accordance with instructions provided can be reasonably expected to result in significant personal injury or death. Users con­templating application of Elantec, Inc. Products in Life Support Systems are requested to contact Elantec, Inc. factory headquarters to establish suitable terms & conditions for these applications. Elan­tec, Inc.’s warranty is limited to replacement of defective components and does not cover injury to persons or property or other consequential damages.
September 19, 2001
13
Printed in U.S.A.
Loading...