Datasheet EE153 Application Notes (Analog Devices)

a

a Engineer To Engineer Note EE-153

aa

Technical Notes on using Analog Devices’ DSP components and development tools

Phone: (800) ANALOG-D, FAX: [phone], EMAIL: [e-mail], FTP: ftp.analog.com, WEB: www.analog.com/dsp

ADSP-2191 PROGRAMABLE
PLL

Created 9/12/2001 - GJO

Overview

The ADSP-2191 includes a clock multiplier, which
provides more flexibility for multiple clock modes than
that of the fixed 2x CLKIN clock mode used by the
popular ADSP-218x DSP family. The ADSP-2191’s
clock multiplier mode enables the chip to run faster than
the input clock rate. The PLL can also be brought up at a
1:1 clock ratio (referred to as Bypass mode) to reduce
power usage. The purpose of this application note is to
describe how to properly configure the programmable
PLL on the ADSP-2191.

Background

The ADSP-2191 provides a user-programmable 1 to 32
multiplication of the input clock, including some
fractional values, to support 128 external to internal (DSP
core) clock ratios. The states of the MSELx, BYPASS, and
DF pins determine how the PLL will function at reset.

If the BYPASS pin is set (=1), the MSELx pins are still
sampled on the rising edge of /RESET and transition back
to programmable flags after the reset is complete; the PLL
is put into bypass; and the input clock is directly used to
generate the clocks for the core (CCLK) and the
peripherals (HCLK). At hard reset the value of the
BYPASS pin automatically determines the value of the
PLLCTL registe r’s BYPASS bit; at any other time,
software controls this bit.

The DF pin (alternately named PF7) controls the input
divider. The input divider is disabled when DF is cleared
(=0). When DF is set (=1), CLKIN is divided by two
prior to being used to generate the core and the peripheral
clocks. At hard reset the value of the DF pin
automatically determines the value of the PLLCTL
register’s DF bit; at any other time, software controls this
bit.

NOTE: DF must be set (=1) when CLKIN is above 100Mhz.
This will ensure that HCLK never exceeds 100Mhz.

The ADSP-2191 MSELx and DF pins are shared and can
be used in three different ways: as clock multiplier select
pins, general-purpose flag pins (referred to as

), or as select pins for external SPI devices. Because

[7:0]

of this, depending on how the programmable flags are to
be used, certain systems considerations must be made to
ensure the MSELx and DF pins are properly configured
and defined when powering-up and hard-resetting the
DSP.

When /Reset is asserted (active low), the states of MSELx,
DF, and BYPASS are used to initialize the PLL. The core
clock and peripheral clock will reflect the states of these
pins. A requirement of the PLL multiplier is that the
MSELx and DF must be in a valid configuration ratio for a
period not exceeding 15 CLKIN cycles following the
assertion of /Reset. Depending on how these pins are
implemented in your system (ex: PF’s or SPI selects),
variables such as capacitive loading and line terminations
could negatively affect the MSELx and DF pins, resulting
in an unwanted or invalid multiplication ratio.

Consider a system with a 16 MHz CLKIN and a desired
core frequency of 160 MHz. In this case, the desired
multiplication ratio would be 10 (PF [7:0] = 0x0A).
Given the 15 CLKIN cycle requirement, after the
assertion of /Reset, a maximum duration of 937 nsec
(15/CLKIN = 15/16M) may pass before the state of PF
[7:0] must assume a valid ratio.

NOTE: The PLL is incapable of recovering from invalid
multiplication ratios (MSELx/DF = 0x00 or 0xFF) applied for
periods exceeding 15 CLKIN cycles.

In some applications, PF [7:0] maybe configured as
outputs. Following the assertion of Reset, there is a
maximum delay of 15ns before PF [7:0] is tri-stated.

Given below are thre e system scenarios and suggested
system considerations given each scenario.

PFx or PF

Scenario 1

In a system, the user doesn’t intend to use PF [7:0] for
anything other than configuring the multiplication ratio
during /Reset. In this case, MSELx and DF can be tied
high or low to achieve the desired multiplication ratio.

Scenario 2

Controlling the PLL

Copyright 2002, Analog Devices, Inc. All rights reserved. Analog Devices assumes no responsibility for customer product d esign or the use or application of customers ’ produc ts or
for any infringements of patents or rights of others w hich may result fro m Analog Devices assist ance. All trademarks and logos are property of their respective holders. Information
furnished by Analog Devices Applications and Development Tools Engineers is believed to be accurate and reliable, however no responsibility is assumed by Analog Devices
regarding the technical accuracy of the content provided in all Analog Devices’ Engineer-to-Engineer Notes.

In a system, the user intends to use PF [7:0] for tasks other
than MSELx and DF selection. As an example, connected
to an external device such as an SPI slave. In this case,
MSELx and DF can be pulled high or low with a suitable
resistor to achieve the desired multiplication ratio. This is
ok provided the devices connected to the MSELx and DF
pins do not drive the PF pins during RESET. In some
systems this may require external logic to disable the
outputs of other devices that would want to over power
the resistors.

As shown in Figure 1, simple pull-ups and pull-downs are
added to MSELx and DF pins.

during and after reset. In other systems external
capacitive loading was so high that pull ups and pull
downs are too slow for the requirement for MSELx and
DF pins to be valid 15 CLKIN cycles after the start of
RESET asserted low.

In this case, it is suggested that the system incorpora t e a
multiplexing circuit to provide the correct MSELx values
during and after reset. This will ensure that the MSELx
timing requirements are satisfied during RESET.
An alternative solution to the above scenario is to put the
PLL in Bypass mode (tie BYPASS high). After /RESET
has been de-asserted, software can configure the
appropriate MSELx bits in the PLLCTL register and then
clear the BYPASS bit. The PLL will then assume the new
PLLCTL settings. As shown in Figure 2, a simple pull-up
is added to BYPASS.

Figure 1. MSELx and DF pin termination.

NOTE: Individual System requirements must ensure the MSELx
and DF pins remain invalid no longer than 15 CLKIN cycles
after the falling edge of /RESET.

Scenario 3

In a system, the user intends to have PF [7:0] connected to
external devi ces, however the option of having pull­ups/pull-downs on MSELx and DF as shown in Figure 1 is
not available. Some systems must have MSEL driven

Figure 2. BYPASS pin termination.

NOTE: In some systems using BYPASS mode, depending on the
chosen boot mode, booting a large program may be very slow.
In Host boot mode, the BYPASS method should be considered
an easy workaround for using the PF pins for application
specific functions without requiring any MSELx considerations
during reset.

EE-153 Page 2

Technical Notes on using Analog Devices’ DSP components and development tools

Phone: (800) ANALOG-D, FAX: [phone], EMAIL: [e-mail], FTP: ftp.analog.com, WEB: www.analog.com/dsp

Software Configuration

The code listed below demonstrates the instructions needed to change the clock mode of the 2191 from Bypass to Multiply.
The code was verified with the BYPASS pin active (tied high).

NOTE: When in bypass mode: cclk=clkin if DIV2=0 (bit7 of the PLL CTL reg) and cclk=clkin/2 if DIV2=1.

/*****************************************************************************************************************/
/* PLL Control Register */

iopg = 0x00; /* Initialize IOPG to Clock and System Co ntr ol */
ax1 = 0x0552; /* Stop the PLL - In Bypass * /

io(0x200) = ax1; /* Write the PL LCTL register */
nop;

ax1 = 0x0352; /* Reprogram to 1x - In Bypass */
io(0x200) = ax1; /* Write the PL LCTL register */
nop;

ax1 = 0x0350; /* Start the PLL - In Bypass * /
io(0x200) = ax1; /* Write the PL LCTL register */
nop;

ax1 = 0x0250; /* Come out of Bypass- Takes ~500 clkin cycles */
io(0x200) = ax1; /* Write the PL LCTL register */

cntr = 1100; /* Wait for a duration of time */
do wt until ce;
wt: nop;
/*****************************************************************************************************************/

Copyright 2002, Analog Devices, Inc. All rights reserved. Analog Devices assumes no responsibility for customer product d esign or the use or application o f customers ’ products or
for any infringements of patents or rights of others w hich may result fro m Analog Devices assist ance. All trademarks and logos are property of their respective holders. Information
furnished by Analog Devices Applications and Development Tools Engineers is believed to be accurate and reliable, however no responsibility is assumed by Analog Devices
regarding the technical accuracy of the content provided in all Analog Devices’ Engineer-to-Engineer Notes.