Page 1
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CSseries
Chip Type, Long Life Assurance
Specifications
Temperature Characteristics
(Max.Impedance Ratio)
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Tangent of loss angle (tan δ)
ESR
(1)
Leakage Current ( 2)
Performance CharacteristicsItem
–55 to +105°C
4 to 16V
22 to 560µF
±20% at 120Hz, 20°C
Less than or equal to the specified value
at
120Hz, 20°C
Less than or equal to the specified value
at
100kHz, 20°C
Less than or equal to the specified value . After 2 minutes' application of rated voltage at 20°C
Z+105°C / Z+20°C 1.25 (100kHz)
Z
–
55°C / Z+20°C 1.25
Endurance
Damp Heat
(Steady State)
Resistance to
Soldering Heat
Marking
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 5000 hours at 105°C.
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 60°C, 90% RH.
After soldering the capacitor under the soldering conditions
prescribed here, the capacitor shall meet the specifications listed at
right, provided that it's temperature profile is measured at the
capacitor top and the terminal.
Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec.
The duration for over +230°C temperature at capacitor surface shall
not exceed 60 seconds.
In the case of peak temp, less than 250°C, reflow soldering shall be
two times maximum.
In the case of peak temp, less than 260°C, reflow soldering shall be
once.
Measurement for solder temperature profile shall be made at the
capacitor top and the terminal.
Navy blue print on the case top
Capacitance change
tan δ
Leakage current ( 2)
ESR
(1)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan δ
Leakage current ( 2)
ESR
(1)
Within ± 20% of the initial capacitance value ( 3)
150% or less than the initial specified value
150% or less than the initial specified value
Less than or equal to the initial specified value
Capacitance change
tan δ
Leakage current ( 2)
ESR
(1)
Within ± 10% of the initial capacitance value ( 3)
130% or less than the initial specified value
130% or less than the initial specified value
Less than or equal to the initial specified value
Load life of 5000 hours at 105°C.
SMD type : Lead free reflow soldering condition at
260°C peak correspondence.
Compliant to the RoHS directive (2002/95/EC).
1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform.
2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120
minutes at 105°C.
3 Initial value : The value before test of examination of resistance to soldering.
Dimensions
Type numbering system (Example : 6.3V 220µF)
Voltage
V46.31016
Code g j A C
Size
φD
L
A
B
C
E
H
φ5
× 6L
5.0
5.9
6.0
5.3
5.3
1.6
0.5 to 0.8
φ6.3 × 6L
6.3
5.9
7.3
6.6
6.6
2.1
0.5 to 0.8
φ8 × 7L
8.0
6.9
9.0
8.3
8.3
3.2
0.8 to 1.1
(mm)
Dimension table in next page.
CS
CF
Long Life
CAT.8100Z
Capacitance
Series
CS
220j941
Voltage
Lot No.
Plastic platform
φD + 0.5 MAX.
(j:6.3v)
L
+0.1
-0.4
0.3 MAX.
C±0.2
B±0.2
H
E
Positive
0.5 MAX.
A±0.2
Negative
P1C2S304J5262718M9C10L11112G13S
14
Taping code
Configuration
Capacitance toleranc (±20%)
Rated capacitance (220µF
Rated voltage (6.3V
Series name
Size code
)
)
Type
Page 2
CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS
CSseries
Standard Ratings
No marked, will be put at 12th digit of type numbering system.
1
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in page 18, 19.
Please refer to page 3 for the minimum order quantity.
Rated ripple current (mArms) at 105°C 100kHz
Rated Capacitance
(µF)
Rated Voltage
(V)(code)
Surge Voltage
(V)
Leakage Current
(µA)
ESR (mΩ)
(at 100kHz 20°C)
Rated Ripple
(mArms)
tan δ Part Number
Case Size
φD × L (mm)
4
(0G)
16
(1C)
10
(1A)
6.3
(0J)
4.6
18.4
11.5
7.2
150
330
330
560
47
100
100
120
220
220
390
33
56
68
120
150
270
22
39
39
68
82
120
120
264
264
448
100
126
126
151
277
277
491
100
112
136
240
300
540
100
125
125
218
262
384
25
20
22
18
35
25
22
22
20
22
22
40
27
30
27
30
22
45
35
30
30
28
28
2200
2800
3200
3600
1600
2400
2800
2800
2800
3200
3200
1300
2300
2100
2300
2600
3200
1100
2000
2200
2200
2800
2800
PCS0G151MCL1GS
PCS0G331MCL1GS
PCS0G331MCL9GS
PCS0G561MCL1GS
PCS0J470MCL1GS
PCS0J101MCL1GS
PCS0J101MCL9GS
PCS0J121MCL9GS
PCS0J221MCL1GS
PCS0J221MCL9GS
PCS0J391MCL1GS
PCS1A330MCL1GS
PCS1A560MCL9GS
PCS1A680MCL1GS
PCS1A121MCL1GS
PCS1A151MCL9GS
PCS1A271MCL1GS
PCS1C220MCL1GS
PCS1C390MCL1GS
PCS1C390MCL9GS
PCS1C680MCL1GS
PCS1C820MCL9GS
PCS1C121MCL1GS
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
0.12
5
×
6
6.3
×
6
8
×
7
8
×
7
5
×
6
5
×
6
6.3
×
6
6.3
×
6
6.3
×
6
8
×
7
8
×
7
5
×
6
6.3
×
6
5
×
6
6.3
×
6
8
×
7
8
×
7
5
×
6
5
×
6
6.3
×
6
6.3
×
6
8
×
7
8
×
7
: In this case, will be put at 12th digit of type numbering system.
9
CAT.8100Z
Loading...