Page 1
PRELIMINARY
Q3 2003
Specification
AC/DC Medical Open Frame
Small Size 3.00” x 5.00 x 1.28”
•
Low Leakage Current
•
Meets Class B, EN55011 Conducted
•
4000 VAC Isolation
•
Medical Safety Agency Approvals
•
Zero Voltage Switching Technology
•
•
•
130 Watts
ECM130 Series
Input
AC Input Voltage • 90-264 VAC
Input Frequency • 47-63 Hz
Power Factor • 0.98 at 115 VAC or 0.90 at 230 VAC
Inrush Current • 30 A max at 115 VAC
60 A max at 230 VAC cold start
at 25°C
Input Current • 2.6 A (rms) max at 115 VAC,
1.3 A (rms) max at 230 VAC
Safety Ground • 120 µA max at 115 VAC, 60 Hz
Leakage Current • 250 µA max at 240 VAC, 60 Hz
Input Protection • Dual fuse at 3.15 A each
Output
Output Voltage • Single trim part for all outputs
Output Power • 130 Watts
Output Voltage Adj. • Fixed, not user adjustable
Minimum Load • 0 min load for single output models
10% for multiple output models
Line Regulation • ±0.5% maximum
Load Regulation • ±1%, ±5% for all secondary outputs
on multiple output models
Ripple & Noise • ±1% pk-pk maximum
Transient Response • 4% max deviation, 500 µs recovery
time for a 25% load change
Temperature • 0.05%/°C
Coefficient
Hold Up Time • >15 ms minimum
Overvoltage • 115% to 140% V1 only
Protection recycle input to reset
Overcurrent • 120% - 150% with auto recovery
Protection
Remote Sense • Output 1 only, compensates for up
to 0.5 V drop
General
Efficiency (Typical) • >80% minimum nominal line
rated load, dependant on model
Power Density • 6.7 W/in
3
single output models
MTBF • 100,000 hrs minimum
Switching Frequency • 120 KHz ±10 KHz
Isolation Voltage • 4000 VAC Input to Output
1500 VAC Input to Ground
500 VAC Output to Ground
Size • 5.00” x 3.00” x 1.28”
(1.35” for multi output models)
Weight • 100 grams
Environmental
Operating • 0 °C to 70 °C see derating chart
Temperature Full power to 50 °C
Cooling • 130 W with 18 CFM airflow
120 W with 10 CFM airflow
100 W with convection cooling
Humidity • 5 to 95% RH, non-condensing
Storage • -20 °C to +85 °C
Temperature
EMC & Safety
EMC • EN61000-3 -2, EN60601-1 -2,
FCC 20780 Level B
EN50082-2 performance A,
no degradation of performance
Safety Approvals • EN60601-1, UL2601-1, CSA C22.2
No. 601.1
CE Mark to applicable sections of
MDD
PH: 508 429.9883
FAX: 800 226.2100
Email: sales@xpiq.com
Holliston, MA 01746 USA
www.XPiQ.com
Intelligent Design Quality Product
XPiQ inc.
* Preliminary datasheet - see website for current specs
ECM130.qxd 15/5/03 9:10 am Page 1
Page 2
Rev 1.0
Mechanical Details - 130 Watts
1. 0 minimum load required for single output models. For multiple output models 5V requires 0.5A and +12V or +15V requires 0.05A
minimum load.
Notes
•
OUTPUT VOLTAGE & CURRENT RATINGS ECM130
Output Output Output Current Ripple & Noise Model
Power Voltage Convection Cooled Max 18 CFM Pk-Pk
(
Number
130 W 5.0 V 20.0 A 26.0 A 50 mV ECM130PS05
130 W 12.0 V 9.0 A 11.0 A 120 mV ECM130PS12
130 W 15.0 V 7.0 A 8.7 A 150 mV ECM130PS15
130 W 24.0 V 4.5 A 5.4 A 240 mV ECM130PS24
130 W 28.0 V 3.9 A 4.6 A 280 mV ECM130PS28
130 W 48.0 V 2.3 A 2.7 A 480 mV ECM130PS48
5.0 V 10.0 A 15.0 A 50 mV
130 W 12.0 V 3.0 A 4.1 A 120 mV
ECM130PT31
-12.0 V 0.8 A 1.1 A 120 mV
5.0 V 10.0 A 15.0 A 50 mV
ECM130PT32
130 W 15.0 V 2.5 A 4.1 A 150 mV
-15.0 V 0.8 A 1.1 A 150 mV
Derating Curve - 130 Watts
PH: 508 429.9883
FAX: 800 226.2100
Email: sales@xpiq.com
Holliston, MA 01746 USA
www.XPiQ.com
Notes:
1. Dimensions in mm. Tolerance is ± 1mm.
2. AC input connector (TB1): Molex 5277-02A or equivalent.
3. DC output connector (TB2): Molex 5273 or equivalent.
4. Remote sense connector (TB3): Molex 5045-02A or equivalent.
Models
Pins PS05 PS12, 15, 24, 48 PT31 PT32
1 +V +V +5V +5.0 V
2 +V +V +5V +5.0 V
3 +V +V +5V +5.0 V
4 +V RET RET RET
5 RET RET RET RET
6 RET RET RET RET
7 RET N/A RET RET
8 RET N/A +12V +15.0 V
9 N/A N/A -12V -15.0 V
10 N/A N/A N/A N/A
* Preliminary datasheet - see website for current specs
*
* Total height of unit 1.28” (32.4 mm) for single output models, 1.35” (34.4 mm) for triple output models.
ECM130.qxd 15/5/03 9:10 am Page 2
Loading...