Datasheet e-cf Datasheet

Download

Page 1

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

CFseries

Chip Type, Standard

Specifications

Temperature Characteristics (Max.Impedance Ratio)

Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Tangent of loss angle (tan δ) ESR

(1)

Leakage Current ( 2)

Performance CharacteristicsItem

–55 to +105°C

2.5 to 25V

3.3 to 1500µF ±20% at 120Hz, 20°C

Less than or equal to the specified value

120Hz, 20°C

Less than or equal to the specified value

100kHz, 20°C

Less than or equal to the specified value. After 2 minutes' application of rated voltage at 20°C Z+105°C / Z+20°C 1.25 (100kHz)

–

55°C / Z+20°C 1.25

Endurance

Damp Heat (Steady State)

Resistance to Soldering Heat

Marking

The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 105°C

The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 60°C, 90% RH.

After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right, provided that it's temperature profile is measured at the capacitor top and the terminal. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In the case of peak temp, less than 250°C, reflow soldering shall be two times maximum. In the case of peak temp, less than 260°C, reflow soldering shall be once. Measurement for solder temperature profile shall be made at the capacitor top and the terminal.

Navy blue print on the case top

Capacitance change tan δ

Leakage current ( 2)

ESR

(1)

Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value

Capacitance change tan δ

Leakage current ( 2)

ESR

(1)

Within ± 20% of the initial capacitance value ( 3) 150% or less than the initial specified value 150% or less than the initial specified value Less than or equal to the initial specified value

Capacitance change tan δ

Leakage current ( 2)

ESR

(1)

Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value

Ultra-low ESR, High ripple current. Load life of 2000 hours at 105°C. SMD type : Lead free reflow soldering condition at 260°C peak correspondence. Compliant to the RoHS directive (2002/95/EC).

1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120

minutes at 105°C.

3 Initial value : The value before test of examination of resistance to soldering.

φD 4 to 6.3（5.5L） 5 to 10（L6）

Code

GB GS

P1C2F304J5165718M9C10L11112G13S

Configuration

Taping code

Size code

Capacitance toleranc (±20%)

Rated capacitance (150µF

)

Rated voltage (6.3V

)

Series name

Type

150j841

0.3 MAX.

φD + 0.5 MAX.

B±0.2

A±0.2

C±0.2

0.5 MAX.

Series

Voltage

(j:6.3v)

Plastic platform

Lot No.

Capacitance

Negative

Positive

+0.1

-0.4

Dimensions

Type numbering system (Example : 6.3V 150µF)

Voltage

V 2.5 4 6.3 10 16 20 25

Code e g j A C D E

Size

φD

L A B C E H

φ4

× 5.5L

4.0

5.4

5.0

4.3

1.0

0.5 to 0.8

φ5 × 6L

5.0

5.9

6.0

5.3

1.6

0.5 to 0.8

φ6.3 × 5.5L

6.3

5.4

7.3

6.6

2.1

0.5 to 0.8

φ6.3 × 6L

6.3

5.9

7.3

6.6

2.1

0.5 to 0.8

φ8 × 7L

8.0

6.9

9.0

8.3

3.2

0.8 to 1.1

φ8 × 12L

8.0

11.9

9.0

8.3

3.2

0.8 to 1.1

φ10 × 8L

10.0

7.9

11.0

10.3

4.6

0.8 to 1.1

φ10 × 10L

10.0

9.9

11.0

10.3

4.6

0.8 to 1.1

φ10 × 12.7L

10.0

12.6

11.0

10.3

4.6

0.8 to 1.1

(mm)

Dimension table in next page.

Low ESRLong Life

Higher

Capacitance,

High

Voltage

CAT.8100Z

Page 2

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

CFseries

Standard Ratings

CAT.8100Z

Rated Voltage

(V)(code)

2.5

（0E）

（0G）

6.3

（0J）

（1A）

Surge Voltage

(V)

2.8

4.6

7.2

11.5

Rated Capacitance

(µF)

100 220 220 470 820 1500 1500 33 100 100 150 150 150 220 330 470 560 680 820 1200 22 47 82 82 100 100 100 120 150 220 330 470 470 470 680 680 820

4.7

6.8 10 15 33 47 47 56 56 120 150 150 270 270 330 330 470 470 560 560

Case Size

φD × L (mm)

6.3

5.5

6.3

12.7

5.5

6.3

5.5

6.3

12.7

5.5

6.3

5.5

6.3

12.7

5.5

6.3

5.5

6.3

12.7

tan δ Part Number

0.12

Leakage Current

(µA)

100 110 110 235 410 750 750 100 100

80 120 300 120 176 264 376 448 544 656 960 100 148 103 103 126 315 126 151 189 277 416 592 592 592 857 857

1033

100 100 100 100 165 235

94 112 112 240 300 300 540 540 660 660 940 940

1120 1120

ESR (mΩ)

(at 100kHz 20°C)

22 20 20 20 17 13 12

200

22 22 22 30 22 21 21 17 13 17 13 10

200

35 23 23 23 25 23 23 22 22 18 12 18 16 14 10

10 240 240 220 200

Rated Ripple

(mArms)

2600 2800 2800 3300 4400 4700 5440

700 2600 2600 2800 2000 2800 3200 3400 4200 4520 4400 4800 5500

700 1600 2600 2600 2800 2200 2800 3000 3200 3400 4200 5300 4300 4600 5000 5500 5800

670

700

700 1500 2600 2600 2500 2500 3000 3200 3300 4500 3600 4000 3700 4600 5300 4800 5230

PCF0E101MCL1GS PCF0E221MCL4GB PCF0E221MCL1GS PCF0E471MCL1GS PCF0E821MCL1GS PCF0E152MCL1GS PCF0E152MCL9GS PCF0G330MCL1GB PCF0G101MCL4GB PCF0G101MCL1GS PCF0G151MCL4GB PCF0G151MCL6GS PCF0G151MCL1GS PCF0G221MCL1GS PCF0G331MCL1GS PCF0G471MCL1GS PCF0G561MCL4GS PCF0G681MCL1GS PCF0G821MCL1GS PCF0G122MCL1GS PCF0J220MCL1GB PCF0J470MCL1GS PCF0J820MCL4GB PCF0J820MCL1GS PCF0J101MCL4GB PCF0J101MCL6GS PCF0J101MCL1GS PCF0J121MCL1GS PCF0J151MCL1GS PCF0J221MCL1GS PCF0J331MCL1GS PCF0J471MCL4GS PCF0J471MCL6GS PCF0J471MCL1GS PCF0J681MCL1GS PCF0J681MCL9GS PCF0J821MCL1GS PCF1A4R7MCL1GB PCF1A6R8MCL1GB PCF1A100MCL1GB PCF1A150MCL1GB PCF1A330MCL1GS PCF1A470MCL6GS PCF1A470MCL1GS PCF1A560MCL4GB PCF1A560MCL1GS PCF1A121MCL1GS PCF1A151MCL6GS PCF1A151MCL1GS PCF1A271MCL4GS PCF1A271MCL1GS PCF1A331MCL4GS PCF1A331MCL1GS PCF1A471MCL1GS PCF1A471MCL9GS PCF1A561MCL1GS PCF1A561MCL9GS

Page 3

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS

No marked, will be put at 12th digit of type numbering system.

Taping specifications are given in page 23. Recommended land size, soldering by reflow are given

in page 18, 19.

Please refer to page 3 for the minimum order quantity.

Rated ripple current (mArms) at 105°C 100kHz

CFseries

Standard Ratings

: In this case, will be put at 12th digit of type numbering system.

CAT.8100Z

Rated Voltage

(V)(code)

（1C）

（1D）

（1E）

Surge Voltage

(V)

18.4

28.7

Rated Capacitance

(µF)

3.3 22 33 39 39 56 82 100 150 180 180 220 220 330 10 22 22 39 47 56 68 82 100 120 150

6.8 10 22 33 47 47 56

Case Size

φD × L (mm)

5.5

6.3

5.5

6.3

8 10

12.7

5.5

6.3

12.7

6.3

12.7

tan δ Part Number

0.12

Leakage Current

(µA)

100 176 106 125 125 179 262 320 480 576 576 704 704

1056

100 100

88 156 188 224 272 328 400 480 600

85 125 275 413 588 588 700

ESR (mΩ)

(at 100kHz 20°C)

260

45 31 31 31 30 28 27 25 16 25 20 14 14

120

50 50 45 45 40 40 40 22 35 20 80 60 50 30 30 45 28

Rated Ripple

(mArms)

660 1210 2400 2400 2400 2900 3200 3300 3500 4400 3600 3900 5050 5000

900 1700 1700 2000 2000 2400 2600 2600 3200 2800 4320 1200 1600 2200 2800 3000 2400 3800

PCF1C3R3MCL1GB PCF1C220MCL1GS PCF1C330MCL1GS PCF1C390MCL4GB PCF1C390MCL1GS PCF1C560MCL1GS PCF1C820MCL1GS PCF1C101MCL1GS PCF1C151MCL1GS PCF1C181MCL4GS PCF1C181MCL1GS PCF1C221MCL1GS PCF1C221MCL9GS PCF1C331MCL1GS PCF1D100MCL1GS PCF1D220MCL4GB PCF1D220MCL1GS PCF1D390MCL1GS PCF1D470MCL1GS PCF1D560MCL1GS PCF1D680MCL1GS PCF1D820MCL1GS PCF1D101MCL1GS PCF1D121MCL1GS PCF1D151MCL1GS PCF1E6R8MCL1GS

PCF1E100MCL1GS PCF1E220MCL1GS PCF1E330MCL1GS PCF1E470MCL4GS PCF1E470MCL1GS PCF1E560MCL1GS