Datasheet DTB723YE, DTB723YM Datasheet (ROHM)

R

-200mA / -30V Low V

(sat) Digital transistors

CE

(with built-in resistors)

DTB723YE / DTB723YM

zApplications zDimensions (Unit : mm)
Inverter, Interface, Driver

zFeature

1) V

CE (sat) is lower than conventional products.

2) Built-in bias resistors enable the configuration of
an inverter circuit without connecting external input resistors
(see equivalent circuit).

3) The bias resistors consist of thin-film resistors
with complete isolation to allow positive biasing of the input.
They also have the advantage
of almost completely eliminating parasitic effects.

4) Only the on / off conditions need to be set for operation,

making the device design easy.

zStructure

PNP epitaxial plannar silicon transistor
(Resistor built-in type)

zPackaging specifications

EMT3 VMT3

TL

3000

T2L

8000

−

−

Part No.
DTB723YE
DTB723YM

Package
Packaging type Taping Taping

Code

Basic ordering
unit (pieces)

zAbsolute maximum ratings (Ta=25°C) zInner circuit

Parameter

Supply voltage
Input voltage
Collector current
Power dissipation
Junction temperature
Storage temperature

∗1 Characteristics of built-in transistor.
∗2 Each terminal mounted on a recommended land.

Symbol

V

CC

IN

V

∗1
∗2

C (max)

I

P

D

Tj

Tstg

DTB723YE DTB723YM

Limits

−30

−15 to +5

−200

150
150

−55 to +150

Unit

V
V

mA

mW

C
C

DTB723YE

EMT3
JEITA No. (SC-75A)
JEDEC No. <SOT-416>

DTB723YM

VMT3

IN

IN

1

=2.2kΩ / R2=10kΩ

1.6

0.3

(3)

(2)

(1)

0.2

R

1

R

2

GND(+)

0.2

0.5

0.5

1.0

Abbreviated symbol : M52

1.2

0.32

(3)

(2)

(1)

0.22

0.40.4

0.8

Abbreviated symbol : M52

OUT

GND(+)

OUT

0.7

0.55

1.6

0.8

0.15

Each lead has same dimensions

0.2

1.2

0.8

0.2

0.5

Each lead has same dimensions

0.13

0.1Min.

(1) GND
(2) IN
(3) OUT

(1) IN
(2) GND
(3) OUT

www.rohm.com

1/2

c

○

2009 ROHM Co., Ltd. All rights reserved.

2009.10 - Rev.C

DTB723YE / DTB723YM

zElectrical characteristics (Ta=25°C)

Parameter Symbol

Input voltage

Output voltage

V
V

V
Input current
Output current

I
DC current gain
Transition frequency

∗

Input resistance
Resistance ratio

∗ Characteristics of built-in transistor.

R2/R

zElectrical characteristic curves

I(off)

I(on)

O(on)

I

I

O(off)

G

f

T

R

Min.

−

−2.5

−

−

−

140

I

−

1.54

1

3.6

1

Typ. Max. Unit Conditions

−

−

−70

−

−

−

260

2.2

4.5

−0.3

−

−300

−3.0

−500

−

−

2.86

5.5

MHz

CC

= −5V, IO= −100µA

V

V

O

= −0.3V, IO= −20mA

V

mV

I

O/II

= −50mA / −2.5mA

mA

I

= −5V

V

nA

V

CC

= −30V, VI=0V

−

O

= −2V, IO= −100mA

V

CE

= −10V, IE=5mA, f=100MHz

V

kΩ

−

−−

Data Sheet

200

180

160

140

120

100

80

60

40

OUTPUT CURRENT : IO (mA)

20

1000

I

100

10

DC CURENT GAIN : G

℃

Ta=25

0

0 0.5 1 1.5 2

OUT PUT VOLT AGE : V

Fi g.1 Output Curr ent vs. Output Vol tage

Ta= 125

℃
　　　　85℃
　　　　25℃

　　　－40℃

1

0.01 0.1 1 10 100 1000

OUTPUT CURENT : I

O

(V)

O

VO=5V

(mA)

Ii=1.0mA
Ii=0.9mA
Ii=0.8mA
Ii=0.7mA

Ii=0.6mA

Ii=0.5mA

Ii=0.4mA

Ii=0.3mA

Ii=0.2mA

Ii=0.1mA
Ii=0mA

10

Ta=－40

℃
　　　　25℃
　　　　85℃

125

℃

1

INPUT VOLTAGE : Vin (V)

0.1
1 10 100 1000

OUTPUT CURRENT : I

Fi g.2 Input V oltag e vs. Output C urrent Fi g.3 Output Curr ent vs. I nput Voltag e

1

Ta= 125

℃
　　　　85℃
　　　　25℃

(on) (V)

O

　　　－40℃

0.1

OUT PUT VOLT AGE : V

0.01
1 10 100 1000

OUTPUT CURRENT : I

V0=0.3V

(mA)

O

IO/II = 20/ 1

(mA)

O

100

VCC=5V

10

(mA )

O

1

0.1

OUTPUT CURRENT : I

0.01

00.511.52

INPUT VOLTAGE : Vin(off) (V)

Ta= 125

85℃
　　　　25℃

　　　－40℃

℃

Fi g.4 D C Cur rent Gai n vs. Output Curr ent Fi g.5 Output Voltag e vs. Output Curr ent

www.rohm.com

2/2

c

○

2009 ROHM Co., Ltd. All rights reserved.

2009.10 - Rev.C

Notes

No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.

The content specied herein is subject to change for improvement without notice.

The content specied herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specications,
which can be obtained from ROHM upon request.

Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.

Great care was taken in ensuring the accuracy of the information specied in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.

The technical information specied herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other par ties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.

Notice

The Products specied in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, ofce-automation equipment, commu­nication devices, electronic appliances and amusement devices).

The Products specied in this document are not designed to be radiation tolerant.

While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.

Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, re or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, re control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.

The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transpor tation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.

If you intend to export or ship overseas any Product or technology specied herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.

www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.

Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.

ROHM Customer Support System

http://www.rohm.com/contact/

R0039

A