Datasheet DTB513ZE, DTB513ZM Datasheet (ROHM)

DTB513ZE / DTB513ZM

z

z

z

z

z

z

z

Transistors

-500mA / -12V Low VCE(sat) Digital transistors
(with built-in resistors)

DTB513ZE / DTB513ZM

Applications

Inverter, Interface, Driver

Feature

CE (sat) is lower than conventional product s.

1) V

2) Built-in bias resistors enable the configuration of an
inverter circuit without connecting external input
resistors (see equivalent circuit).

3) The bias resistors consist of thin-film resistors with
complete isolation to allow positive biasing of the
input. They also have the advantage of almost
completely eliminating parasitic effects.

4) Only the on / off conditions need to be set for

operation, making the devi ce design easy.

Structure

PNP epitaxial planna r silicon transistor
(Resistor built-in type)

zDimensions (Unit : mm)

DTB513ZE

EMT3
JEITA No. (SC-75A)
JEDEC No. <SOT-416>

DTB513ZM

VMT3

1.6

0.3

(3)

(2)

(1)

0.2

0.2

0.5

0.5

1.0

Abbreviated symbol : Y11

1.2

0.32

(3)

(2)

(1)

0.22

0.40.4

0.8

Abbreviated symbol : Y11

0.7

0.55

1.6

0.8

0.15

Each lead has same dimensions

0.2

1.2

0.8

0.2

Each lead has same dimensions

(1) GND

0.1Min.

(2) IN
(3) OUT

(1) IN

0.13

0.5

(2) GND
(3) OUT

Absolute maximum ratings (Ta=25qC)

Parameter

Supply voltage
Input voltage
Collector current
Power dissipation
Junction temperature
Storage temperature

∗1 Characteristics of built-in transistor.
∗2 Each terminal mounted on a recommended land.

z

Electrical characteristics (Ta=25qC)

Parameter Symbol

Input voltage

Output voltage
Input current
Output current
DC current gain
Transition frequency

∗

Input resistance
Resistance ratio

∗ Characteristics of built-in transistor.

Symbol

∗1

C (max)

I

∗2

DTB513ZE DTB513ZM

CC

V

V

IN

P

D

Tj

Tstg

Min.

V

I(off)

−

V

I(on)

−2.5

V

O(on)

−

I

I

−

I

O(off)

−

140

G

I

f

T

−

0.7

R

1

8.0

R2/R

1

Limits

−12

−10 to +5

−500

150
150

−55 to +150

Unit

V
V

mA

mW

C
C

Typ. Max. Unit Conditions

V

CC

=−5V, IO=−100μA

V

V

O

=−0.3V, IO=−20mA

mV

I

O/II

=−100mA / −5mA

mA

I

= −5V

V

μA

V

CC

=−12V, VI=0V

−

O

=−2V, IO=−100mA

V

MHz

CE

=−10V, IE=5mA,f=100MHz

V

kΩ

−

−−

−60

260

1.0
10

−0.3

−

−

−

−300

−6.4

−

−0.5

−

−

−

−

1.3
12

Packaging specifications

Package
Packaging type Taping Taping

Code

Basic ordering

Part No.

unit (pieces)

DTB513ZE
DTB513ZM

Equivalent circuit

IN

IN

R1=1.0kΩ / R2=10kΩ

EMT3 VMT3

TL

3000

−

R

1

R

2

T2L

8000

−

OUT

GND(+)

OUT

GND(+)

Rev.A!!!!1/2

Transistors

z

‑

‑

Electrical characteristic curves

I

=4.5mA

=5mA

I

I

500

Ta=25

450
400
350

(mA)

O

300
250
200
150
100

50

OUTPUT CURRENT : I

℃

pulsed

0

012

OUTPUT VOLTAGE : VO(V)

Fig.1 Output Current vs. Output Voltage

I

=4mA

I

I

I

=3.5mA

I

=3mA

I

I

I

=2.5mA

I

I

=2mA

I

=1.5mA

I

I

=1mA

I

I

I

=0.5mA

I

I

=0

I

10

Vo=0.3V

pulsed

(on) (V)

I

1

INPUT VOLTAGE : V

0.1

0.1 1 10 100 1000
OUTPUT CURRENT : IO (mA)

Ta=-40
Ta=25
Ta=125

Fig.2 Input Voltage vs. Output Current

DTB513ZE / DTB513ZM

100

VCC=5V

pulsed

10

(mA)

O

℃

℃

1

0.1

OUTPUT CURRENT : I

0.01

00.511.52
INTPUT VOLTAGE : VI(off) (V)

Fig.3 Output Current vs. Input Voltage

Ta=125
Ta=25
Ta=-40

℃

℃

℃

1000

VO=5V

Ta=125

pulsed

I

100

10

DC CURRENT GAIN : G

1

0.1 1 10 100 1000
OUTPUT CURRENT : IO (mA)

℃

Ta=-40

Ta=25

℃

℃

Fig.4 DC Current Gain vs. Output Current

1

IO/II=20/1

pulsed

(on) (V)

O

0.1

OUTPUT VOLTAGE : V

0.01
1 10 100 1000

Ta=125

℃

Ta=25

Ta=-40

℃

‑

OUTPUT CURRENT : IO (mA)

‑

℃

Fig.5 Output Voltage vs. Output Current

Rev.A!!!!2/2

Appendix

Notes

No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.

The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers
and other safety devices), please be sure to consult with our sales representative in advance.
It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance
of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow
for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in
order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM
cannot be held responsible for any damages arising from the use of the products under conditions out of the
range of the specifications or due to non-compliance with the NOTES specified in this catalog.

Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.

ROHM Customer Support System

www.rohm.com

THE AMERICAS / EUROPE / ASIA / JAPAN

Contact us : webmaster@ rohm.co. jp

Copyright © 2008 ROHM CO.,LTD.

21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan

TEL : [phone]
FAX : [phone]

Appendix1-Rev2.0