Datasheet DS1023S-500, DS1023S-50, DS1023S-25, DS1023S-200, DS1023S-100 Datasheet (Dallas Semiconductor)

1 of 16 022300

FEATURES

 Step sizes of 0.25 ns, 0.5 ns, 1 ns, 2 ns, 5 ns
 On-chip reference delay
 Configurable as delay line, pulse width

modulator, or free-running oscillator

 Can delay clocks by a full period or more
 Guaranteed monotonicity
 Parallel or serial programming
 Single 5V supply
 16-pin DIP or SOIC package

PIN ASSIGNMENT

PIN DESCRIPTION

IN - Input
P0/Q - Parallel Input P0 (parallel mode)

- Serial Data Output (serial mode)

P1/CLK - Parallel Input P1 (parallel mode)

- Serial Input Clock (serial mode)

P2/D - Parallel Input P2 (parallel mode)

- Serial Data Input (serial mode)
P3 - P7 - Remaining Parallel Inputs
GND - Ground

OUT/OUT - Output
REF/PWM - Reference or PWM Output

P /S - Parallel / Serial Programming

Select
MS - Output Mode Select
LE - Input Latch Enable
VCC - Supply Voltage

DESCRIPTION

The DS1023 is an 8-bit programmable delay line similar in function to the DS1020/DS1021.

Additional features have been added to extend the range of applications:

The internal delay line architecture has been revised to allow clock signals to be delayed by up to a full
period or more. Combined with an on-chip reference delay (to offset the inherent or “step zero” del ay of
the device) clock phase can now be varied over the full 0-360 degree range.

DS1023

8-Bit Programmable Timing Element

www.dalsemi.com

IN

LE

Q/P0

CLK/P1

D/P2

P3
P4

GND

16
15
14
13
12

11
10

9

V

CC

OUT/OUT

REF/PWM

P/S
P7
P6
MS

P5

1
2

3
4

5
6

7
8

DS1023 300-mil DIP

DS1023S 300-mil SOIC

DS1023

2 of 16

On-chip gating is provided to allow the device to provide a pulse width modulated output, triggered by
the input with duration set by the programmed value.

Alternatively the output signal may be inverted on chip, allowing the device to perform as a free-running
oscillator if the output is (externally) connected to the input.

PROGRAMMING

The device programming is identical to the DS1020/DS1021. Note, however, that the serial clock and
data pins are shared with three of the parallel input pins.

The P /S pin controls the same function as “Mode Select” on the DS1020/DS1021 (but with reversed
polarity). A low logic level on this pin enables the parallel programming mode. LE must be at a high
logic level to alter the programmed value; when LE is taken low the data is latched internally and the
parallel data inputs may be altered without affecting the programmed value. This is useful for
multiplexed bus applications. For hard-wired applications LE should be tied to a high logic level.

When P /S is high serial programming is enabled. LE must be held high to enable loading or reading of
the internal register, during which time the delay is determined by the previously programmed value.
Data is clocked in MSB to LSB order on the rising edge of the CLK input. Data transfer ends and the
new value is activated when LE is taken low.

PARALLEL MODE (P /S = 0)

In the PARALLEL programming mode, the output of the DS1023 will reproduce the logic state of th e
input after a delay determined by the state of the eight program input pins P0 - P7. The parallel inputs
can be programmed using DC levels or computer-generated data. For infrequent modification of the
delay value, jumpers may be used to connect the input pins to VCC or ground. For applications requiring
frequent timing adjustment, DIP switches may be used. The latch enable pin (LE) must be at a logic 1 in
hardwired implementations.

Maximum flexibility is obtained when the eight parallel programming bits are set using computer­generated data. When the data setup (t

DSE

) and data hold (t

DHE

) requirements are observed, the enable pin
can be used to latch data supplied on an 8-bit bus. Latch enable must be held at a logic 1 if it is not used
to latch the data. After each change in delay value, a settling time (t

EDV

or t

PDV

) is required before input

logic levels are accurately delayed.

SERIAL MODE (P/S = 1)

In the SERIAL programming mode, the output of the DS1023 will reproduce the logic state of the input
after a delay time determined by an 8-bit value clocked into serial port D. While observing data setup
(t

DSC

) and data hold (t

DHC

) requirements, timing data is loaded in MSB-to-LSB order by the rising edge of
the serial clock (CLK). The latch enable pin (LE) must be at a logic 1 to lo ad or read the internal 8-bit
input register, during which time the delay is determined by the last value activated. Data transfer ends
and the new delay value is activated when latch enable (LE) returns to a logic 0. After each change, a
settling time (t

EDV

) is required before the delay is accurate.

As timing values are shifted into the serial data input (D), the previous contents of the 8-bit input register
are shifted out of the serial output pin (Q) in MSB-to-LSB order. By connecting the serial output of one
DS1023 to the serial input of a second DS1023, multiple devices can be daisy-chained (cascaded) for
programming purposes (Figure 1). The total number of serial bits must be eight times the number of units
daisy-chained and each group of 8 bits must be sent in MSB-to-LSB order.

DS1023

3 of 16

Applications can read the setting of the DS1023 Delay Line by connecting the serial output pin (Q) to the
serial input (D) through a resistor with a value of 1 to 10 kohms (Figure 2). Since the read process is
destructive, the resistor restores the value read and provides isolation when writing to the device. The
resistor must connect the serial output (Q) of the last device to the serial input (D) of the first devic e of a
daisy chain (Figure 1). For serial readout with automatic restoration through a resistor, the device used to
write serial data must go to a high impedance state.

To initiate a serial read, latch enable (LE) is taken to a logic 1 while serial clock (CLK) is at a logic 0.
After a waiting time (t

EQV

), bit 7 (MSB) appears on the serial out put (Q). On the first rising (0 --> 1 )
transition of the serial clock (CLK), bit 7 (MSB) is rewritten and bit 6 appears on the output after a time
t

CQV

. To restore the input register to its original state, this clocking process must be repeated ei ght times.
In the case of a daisy chain, the process must be repeated eight times per package. If the value read is
restored before latch enable (LE) is returned to logic 0, no settling time (t

EDV

) is required and the

programmed delay remains unchanged.

Since the DS1023 is a CMOS design, unused input pins (P3 - P7) must be connected to well-defined logic
levels; they must not be allowed to float. Serial output Q/P0 should be allowed to float if unused.

CASCADING MULTIPLE DEVICES (DAISY CHAIN) Figure 1

SERIAL READOUT Figure 2

REFERENCE DELAY

In all delay lines there is an inherent, or “step zero”, delay caused by the propagation dela y through the
input and output buffers. In this device the step zero delay can be quite large compared to the delay step
size. To simplify system design a reference delay has been included on chip which may be used to
compensate for the step zero delay. In practice this means that if the device is supplied with a clock, for
example, the minimum programmed output delay is effectively zero with respect to the reference delay.

DS1023

4 of 16

For highest accuracy it is strongly recommended that the reference delay is used. Variations in input
voltage levels and transition times can significantly alter the measured delay from input to output. This
effect is totally removed if the reference delay output is used. Furthermore, adverse effects on step zero
delay caused by process temperature coefficients are also cancelled out.

INPUT PULSE DURATION

The internal architecture of the DS1023 allows the output delay time to be considerably longer than the
input pulse width (see ac specifications). This feature is useful in many applications, in particular clock
phase control where delays up to and beyond one full clock period can be achieved.

MODE SELECT

The DS1023 has four possible output functions but only two output pins. The functionality of the two
output pins is determined by the Mode Select (MS) pin.

MS = 0 Figure 3

Output Function Name Pin Number

Reference Output REF 9
Delayed Output OUT 15

OUT is a copy of the input waveform that is delayed by an amount set b y the programmed values (Table

1). A programmed value of zero will still result in a non-zero delay as indicated in the Step Zero delay
specification. The signal on OUT is the same polarity as the input.

REF is a fixed reference delay. It also is a copy of the input waveform but the dela y interval is fixed to a
value approximately equal to the Step Zero Value of the device (as shown in the Reference Delay
specification). In fact the device is trimmed to ensure that the Reference Delay is always slightly longer
than the Step Zero Value (by 1.5 ns typically).

DS1023

5 of 16

MS = 1 Figure 4

Output Function Name Pin Number

Pulse Width Modulated Output PWM 9
Delayed and Inverted Output

OUT

15

PWM is an output triggered by the rising edge of the input waveform. After a time interval approximatel y
equal to the Step Zero delay of the device the PWM output will go high. The output will return to a low
level after a time interval determined by the programmed values (Table 1). Hence output pulse widths can
be obtained from (nearly) zero to the full delay range of the device. In practice the minimum output pulse
width is limited by the response time of the device to approximately 5ns. Programmed values less than
this will result in degradation of the output high level voltage until ultimately no discernible output pulse
is produced. The frequency/repetition rate of the output is determined by the input frequency. The input
pulse width can be shorter than the output pulse width, and is limited onl y by the minimum input pulse
width specification. The PWM function is not “re-triggerable”, subsequent input tri gger pulses should
not be present until the output has returned to a low level.

OUT is an inverted copy of the input waveform that is delayed by an amount set by the programmed

values (Table 1). A programmed value of zero will still result in a non-zero dela y as indic ated in the Step
Zero delay specification. The OUT pin may also be externall y connected to the input pin to produce a

free-running oscillator. The frequency of oscillation is determined by the programmed dela y value of the
device (see Table 2).

DS1023

6 of 16

FUNCTIONAL BLOCK DIAGRAM Figure 5

DELAY LINE DETAIL (CONCEPTUAL) - DS1023-200, DS1023-500 Figure 6

DS1023

7 of 16

DELAY LINE DETAIL (CONCEPTUAL) - DS1023-25, DS1023-50, DS1023-100

Figure 7

PART NUMBER TABLE Table 1

DELAYS RANGES AND TOLERANCE (all times measured in ns)

PART

NUMBER

STEP

SIZE

MAX. DELAY TIME (1)/

MAX. OUTPUT PULSE

WIDTH (2)

MAXIMUM

DEVIATION (3)

MAXIMUM

I/P FREQ

MINIMUM I/P

PULSE
WIDTH

DS1023-025 0.25 63.75

±1

25 MHz 20

DS1023-050 0.50 127.5

±2

25 MHz 20

DS1023-100 1.0 255

±4

25 MHz 20

DS1023-200 2.0 510

±8

25 MHz 20

DS1023-500 5.0 1275

±20

10 MHz 50

1. In “Normal” mode (MS=0). Measured with respect to REF output. The minimum delay time is zero

(or less, by 1.5 ns typically)

2. In PWM mode (MS=1). The minimum output pulse width for reliable operation is 5 ns; programmed

values less than this may produce reduced output voltage levels or no output at all.

3. This is the deviation from a straight line drawn between the step zero value and the maximum

programmed delay time.

OSCILLATOR CONFIGURATION Table 2

PART NUMBER

STEP

SIZE (4)

MINIMUM O/P

FREQUENCY (5)

MAXIMUM O/P

FREQUENCY (5)

DS1023-025 0.5 6.6 MHz 22 MHz
DS1023-050 1.0 3.6 MHz 22 MHz
DS1023-100 2.0 1.9 MHz 22 MHz
DS1023-200 4.0 0.98 MHz 22 MHz
DS1023-500 10.0 0.4 MHz 22 MHz

4. Step size in output period (in ns).

5. Maximum output frequency depends on the actual step zero delay value, worst case values are shown

in the table. The output period is given by: 2 * t

D

where: tD = absolute delay value.

DS1023

8 of 16

DALLAS SEMICONDUCTOR TEST CIRCUIT Figure 8

TEST SETUP DESCRIPTION

Figure 8 illustrates the hardware configuration used for measuring the timing parameters of the DS1023.
The input waveform is produced by a precision pulse generator under software control. Time delays are
measured by a time interval counter (20 ps resolution) connected to the output. The DS1023 serial and
parallel ports are controlled by interfaces to a central computer. All measurements are fully automated
with each instrument controlled by the computer over an IEEE 488 bus.

TEST CONDITIONS

INPUT:
Ambient Temperature: 25°C ±=3°C
Supply Voltage (VCC): 5.0V ±=0.1V
Input Pulse: High = 3.0V ±=0.1V

Low = 0.0V ±=0.1V

Source Impedance: 50 ohms max.
Rise and Fall Time: 3.0 ns max.

(measured between

0.6V and 2.4V)

Pulse Width: 500 ns
Period: 1 µs

NOTE: Above conditions are for test only and do not restrict the operation of the device under other data
sheet conditions.

OUTPUT:
Output is loaded with a 74F04. Delay is measured between the 1.5V level of the rising edge of the input
signal and the 1.5V level of the corresponding edge of the output.

DS1023

9 of 16

ABSOLUTE MAXIMUM RATINGS*

Voltage on Any Pin -1.0V to +7.0V
Operating Temperature Range 0°C to 70°C
Storage Temperature -55°C to +125°C
Soldering Temperature 260°C for 10 seconds
Short Circuit Output Current 50 mA for 1 second

* This is a stress rating only and functional operation of the device at these or an y other conditions above

those indicated in the operation sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods of time may affect reliability.

DC ELECTRICAL CHARACTERISTICS (0°C to 70°C; VCC = 5V ± 5%)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Supply Voltage V

CC

4.75 5 5.25 V

High Level Input Voltage V

IH

2V

CC

+0.5 V

Low Level Input Voltage V

IL

-0.5 0.8 V
Input Leakage Current
(0<VI <VCC )I

I

-1 +1 µA

Active Current I

CC

30 60 mA
High Level Output Current
(VCC = Min, VOH = 2.7V)

I

OH

-1 mA

Low Level Output Current
(VCC = Min, VOL = 0.5V)

-Q output

-All other outputs

I

OL

I

OL

4
8

mA
mA

AC ELECTRICAL CHARACTERISTICS - CONTROL/INTERFACE
SPECIFICATIONS ALL SPEED OPTIONS (T

A

= 0°°°°C to 70°°°°C; VCC= 5V ±±±±====5%)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Serial Clock Frequency f

CLK

10 MHz

Input Pulse Width (LE, CLK) t

W

50 ns

Data Setup to Clock t

DSC

30 ns

Data Hold from Clock t

DHC

0ns

Data Setup to Enable t

DSE

30 ns

Data Hold from Enable t

DHE

0ns

Enable Setup to Clock t

ES

0ns

Enable Hold from Clock t

EH

30 ns

LE to Q Valid t

EQV

50 ns

LE to Q Hi-Z t

EQZ

050ns

CLK to Q Valid t

CQV

50 ns

CLK to Q Invalid t

CQX

0ns

Parallel Input to Delay Valid t

PDV

500 ns

Parallel Input to Delay Invalid t

PDX

0ns

LE to Delay Valid t

EDV

500 ns

LE to Delay Invalid t

EDX

0ns

Power Up Time t

PU

100 ms

DS1023

10 of 16

TIMING DIAGRAM: SILICON DELAY LINE Figure 9

AC ELECTRICAL CHARACTERISTICS ­DS1023-025 Delay Specifications (T

A

= 0°°°°C to 70°°°°C; VCC = 5V ±±±±====5%)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Step Zero Delay

-absolute

-wrt REF

t

D0

t

DREF0

-2

16.5

-1.5

22

0

ns
ns

1, 13
2, 14

Reference Delay t

REF

18 22 ns 3, 13

Delay Step Size t

STEP

0 0.25 0.75 ns 4

Maximum Delay

-absolute

-wrt REF

t

DMAX

t

DREF

75
60

80

63.75

89

67.5

ns
ns

5, 13

6, 14
Delay Matching, Rising Edge
to Falling Edge

-1 +1 ns 15

Integral Non-linearity
(deviation from straight line) t

err

-1 0 +1 ns 7

OUT Delta Delay

t

INV0

012ns8

IN High to PWM High t

PWM0

16.5 22 ns 9, 13
Minimum PWM Output
Pulse Width t

PWM

5ns10

Minimum Input Pulse Width t

WI

20 ns 11
Minimum Input Period 40 ns 12
Input Rise and Fall Times tr, t

f

01µs16

DS1023

11 of 16

AC ELECTRICAL CHARACTERISTICS –
DS1023-050 Delay Specifications (T

A

= 0°°°°C to 70°°°°C; VCC = 5V ±±±±====5%)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Step Zero Delay

-absolute

-wrt REF

t

D0

t

DREF0

-2

16.5

-1.5

22

0

ns
ns

1, 13
2, 14

Reference Delay t

REF

18 22 ns 3, 13

Delay Step Size t

STEP

0 0.5 1.5 ns 4

Maximum Delay

-absolute

-wrt REF

t

DMAX

t

DREF

139
123

144

127.5

154
132

ns
ns

5, 13

6, 14
Delay Matching, Rising Edge
to Falling Edge

-1 +1 ns 15

Integral Non-linearity
(deviation from straight line) t

err

-2 0 +2 ns 7

OUT Delta Delay

t

INV0

012ns8

IN High to PWM High t

PWM0

16.5 22 ns 9, 13
Minimum PWM Output
Pulse Width t

PWM

5ns10

Minimum Input Pulse Width t

WI

20 ns 11
Minimum Input Period 40 ns 12
Input Rise and Fall Times tr, t

f

01µs16

AC ELECTRICAL CHARACTERISTICS –
DS1023-100 Delay Specifications (T

A

= 0°°°°C – 70°°°°C; VCC = 5V ±±±±====5%)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Step Zero Delay

-absolute

-wrt REF

t

D0

t

DREF0

-2

16.5

-1.5

22

0

ns
ns

1, 13
2, 14

Reference Delay t

REF

18 22 ns 3, 13

Delay Step Size t

STEP

0 1 1.5 ns 4

Maximum Delay

-absolute

-wrt REF

t

DMAX

t

DREF

262
247

272
255

285
263

ns
ns

5, 13

6, 14
Delay Matching, Rising Edge
to Falling Edge

-1 +1 ns 15

Integral Non-linearity
(deviation from straight line)

t

err

-4 0 +4 ns 7

OUT Delta Delay

t

INV0

012ns8

IN High to PWM High t

PWM0

16.5 22 ns 9, 13
Minimum PWM Output
Pulse Width t

PWM

5ns10

Minimum Input Pulse Width t

WI

20 ns 11
Minimum Input Period 40 ns 12
Input Rise and Fall Times tr, t

f

01µs16

DS1023

12 of 16

AC ELECTRICAL CHARACTERISTICS ­DS1023-200 Delay Specifications (T

A

= 0°°°°C - 70°°°°C; VCC = 5V ±±±±====5%)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Step Zero Delay

-absolute

-wrt REF

t

D0

t

DREF0

-2

16.5

-1.5

22

0

ns
ns

1, 13
2, 14

Reference Delay t

REF

18 22 ns 3, 13

Delay Step Size t

STEP

1.5 2 2.5 ns

Maximum Delay

-absolute

-wrt REF

t

DMAX

t

DREF

509
494

527
510

548
526

ns
ns

5, 13

6, 14
Delay Matching, Rising Edge
to Falling Edge

-1 +1 ns 15

Integral Non- linearity
(deviation from straight line) t

err

-8 0 +8 ns 7

OUT Delta Delay

t

INV0

012ns8

IN High to PWM High t

PWM0

16.5 22 ns 9, 13
Minimum PWM Output
Pulse Width t

PWM

5ns10

Minimum Input Pulse Width t

WI

20 ns 11
Minimum Input Period 40 ns 12
Input Rise and Fall Times tr, t

f

01µs16

AC ELECTRICAL CHARACTERISTICS –
DS1023-500 Delay Specifications (T

A

= 0°°°°C – 70°°°°C; VCC = 5V ±±±±====5%)

PARAMETER SYMBOL MIN TYP MAX UNITS NOTES

Step Zero Delay

-absolute

-wrt REF

t

D0

t

DREF0

-2

16.5

-1.5

22

0

ns
ns

1, 13
2, 14

Reference Delay t

REF

18 22 ns 3, 13

Delay Step Size t

STEP

456ns

Maximum Delay

-absolute

-wrt REF

t

DMAX

t

DREF

1250
1235

1292
1275

1337
1315

ns
ns

5, 13

6, 14
Delay Matching, Rising Edge
to Falling Edge

-1 +1 ns 15

Integral Non- linearity
(deviation from straight line) t

err

-20 0 +20 ns 7

OUT Delta Delay

t

INV0

012ns8

IN High to PWM High t

PWM0

16.5 22 ns 9, 13
Minimum PWM Output
Pulse Width t

PWM

5ns10

Minimum Input Pulse Width t

WI

50 ns 11
Minimum Input Period 100 ns 12
Input Rise and Fall Times tr, t

f

01µs16

DS1023

13 of 16

NOTES:

1. Delay from input to output with a programmed delay value of zero.

2. This is the relative delay between REF and OUT. The device is trimmed such that when programmed

to zero delay the OUT output will always appear before the REF output. This parameter is
numerically equal to tD0-t

REF

. (See Figure 15).

3. The reference delay is closely matched to the step zero delay to allow relative timings down to zero or

less.

4. This is the worst case condition when the SubDAC switches from its maximum to minimum value.
All other steps are ±0.5 lsb. This comment does not apply to -200 and -500 devi ces which do not use
a SubDAC. (See Figure 14)

5. This is the actual measured delay from IN to OUT. This parameter will exhibit greater temperature
variation than the relative delay parameter.

6. This is the actual measured delay with respect to the REF output. This parameter more closely
reflects the programmed delay value than the absolute delay parameter. (See Figure 15).

7. This is the maximum deviation from a straight line response drawn between the step z ero delay and
the maximum programmed delay. Therefore it is indicative of the maximum error in the measured
delay versus the programmed delay with respect to the REF output. The absolute delay measurement
from IN to OUT will in addition have an offset error equal to the step zero delay and its tolerance.
(See Figure 13).

8. Change in delay value when the inverted output is selected instead of the normal, non-inverting,
output.

9. In PWM mode the delay between the rising edge of the input and the rising edge of the output.

10. The minimum value for which the PWM pulse width should be programmed. Narrower pulse widths
may be programmed but output levels may be impaired and ultimately no output pulse will be
produced.

11. This is the minimum allowable interval between transitions on the input to assure accurate device
operation. This parameter may be violated but timing accuracy may be impaired and ultimately ver y
narrow pulse widths will result in no output from the device.

12. This parameter applies to normal delay mode only. When a 50% duty cycle input clock is used this
defines the highest usable clock frequency. When asymmetrical clock inputs are used the maximum
usable clock frequency must be reduced to conform to the minimum input pulse width requirement. In
PWM mode the minimum input period is equal to the step zero delay and the programmed delay
(t

DO

+ tD).

13. Measured from rising edge of the input to the rising edge of the output (t

DR

).

14. From rising edge to rising edge.

15. This is the difference in measured delay between rising edge (input to output), t

DR

and falling edges

(input to output), t

DF

.

16. Faster rise and fall times will give the greatest accuracy in measured delay. Slow edges (outside the
specification maximum) may result in erratic operations.

DS1023

14 of 16

TERMINOLOGY

Period: The time elapsed between the leading edge of the first pulse and the leading edge of the

following pulse.

tWI (Pulse Width): The elapsed time on the pulse between the 1.5V point on the leading edge and the 1.5V

point on the trailing edge, or the 1.5V point on the trailing edge and the 1.5V point on the leading edge.

t

RISE

(Input Rise Time): The elapsed time between the 20% and the 80% point on the leading edge of the

input pulse.

t

FALL

(Input Fall Time): The elapsed time between the 80% and the 20% point on the trailing edge of the

input pulse.

tD (Time Delay): The elapsed time between the 1.5V point on the edge of an input pulse and the 1.5V

point on the corresponding edge of the output pulse.

TIMING DIAGRAM: NON-LATCHED PARALLEL MODE
(

P/S = 0, LE = 1) Figure 10

TIMING DIAGRAM: LATCHED PARALLEL MODE (P/S = 0) Figure 11

DS1023

15 of 16

TIMING DIAGRAM: SERIAL MODE (P /S = 1) Figure 12

DELAY vs PROGRAMMED VALUE Figure 13

t

DO

t

DMAX

(measured)

DS1023

16 of 16

DETAILED RESPONSE CHARACTERISTICS Figure 14

DELAY PARAMETERS Figure 15

NOTES:

1. The device is trimmed such that t

DREF

= 255 * (nominal step size).

2. Since t

DO

is trimmed to be less than t

REF

, the actual step size will be slightly above the nominal value.

3. Consequently the range of absolute delay values (t

DMAX-tDO

) will also exceed the nominal range by an

amount equal to t

DREF0

.