Datasheet D1D12 Specification

Series 1-DC

• D1D to D5D series SSRs; MOSFET output

• Ratings from 7A to 40A @ 200 VDC, and from 7A to 10A @ 500 VDC

• DC Control

• Relays are easily paralleled for higher-current applications

• CE Compliant to EN60950-1

PRODUCT SELECTION

Load Voltage 7A 10A 12A 20A 40A

100 VDC D1D07 D1D12 D1D20 D1D40
200 VDC D2D07 D2D12 D2D40
400 VDC D4D07 D4D12
500 VDC D5D07 D5D10

OUTPUT SPECIFICATIONS (1)

Description 7A 12A 20A 40A 7A 12A 40A 7A 12A 7A 10A

Operating Voltage Range 0-100 0-100 0-100 0-100 0-200 0-200 0-200 0-400 0-400 0-500 0-500
Maximum Off-State Leakage Current @ Rated Voltage [mA] 0.1 0.2 0.3 0.3 0.1 0.3 0.3 0.3 0.3 0.2 0.3
Maximum Load Current (3) [Adc] 7 12 20 40 7 12 40 7 12 7 10
Minimum Load Current [mA] 1 1 1 1 1 1 1 1 1 1 1
Maximum Surge Current [Adc] (10ms) 15 28 42 106 22 27 106 17 36 19 29
Maximum On-State Voltage Drop @ Rated Current [Vdc] 2.0 1.6 2.1 2.1 2.0 2.8 2.1 4.2 4.2 5.7 5.5
Thermal Resistance Junction to Case (Rjc) [°C/W] 2.2 1.34 1.06 0.83 1.5 1.06 0.83 1.06 0.8 1.0 0.8
Maximum On-State Resistance [RDS-ON][Ohms] 0.29 0.13 0.10 0.05 0.29 0.23 0.05 0.6 0.35 0.8 0.55

INPUT SPECIFICATIONS (1)

Description DC Control

Control Voltage Range 3.5-32 VDC
Minimum Turn-On Voltage 3.5 VDC
Minimum Turn-Off Voltage 1.0 VDC
Minimum Input Current @ 5VDC 1.6 mA
Maximum Input Current @ 32VDC 28 mA
Nominal Input Impedance See Note 4
Maximum Turn-On Time [µsec] 100
Maximum Turn-Off Time [msec] 1.0

GENERAL SPECIFICATIONS

Description Parameters

Dielectric Strength, Input/Output/Base (50/60Hz) 2500 VRMS
Minimum Insulation Resistance (@ 500 V DC)

Maximum Capacitance, Input/Output 50 pF
Ambient Operating Temperature Range -20 to 80°C
Ambient Storage Temperature Range -20 to 125 °C
Weight (typical) 3.0 oz (86.5g)
Encapsulation Thermally conductive Epoxy
Terminals Screws and Saddle Clamps Furnished, Unmounted
Recommended Terminal Screw Torque Range: 6-32 Screws - 10 in lbs. 8-32 and 10-32 Screws -20 in. lbs. (Screws dry without grase)

GENERAL NOTES

1) All parameters at 25°C and per section unless otherwise specified.

2) Dielectric strength and insulation resistance are measured between input and output

3) Heat sinking required, for derating curves see page 3.

4) Input circuitry version incorporates active current limiter.

109 Ohm

MECHANICAL SPECIFICATIONS

THERMAL DERATE INFORMATION

WIRING DIAGRAM

MAXIMUM SURGE VS DURATION

AGENCY APPROVALS

EN60950 : Meets the requirements of sections1.5: 1,7: 2.9: 2.10.5.3: 4.2: 4.5: 4.7:
Designed in accordance with the requirements of IEC 62314

UL E116950 (100 Volt Models 1-DC Only )

Rev. 120711

ANNEX - ENVIROMENTAL INFORMATION