Datasheet CY7C68013A Datasheet (CYPRESS)

Download

Page 1

EZ-USB FX2LP™ USB Microcontroll

A A

1.0 Features (CY7C68013A/14A/15A/16A)

• USB 2.0–USB-IF high speed certified (TID # 40440111)

• Single-chip integr ated USB 2.0 transceiver, smart SIE, and enhanced 8051 microprocessor

• Fit, form and function compatible with the FX2

—Pin-compatible —Object-code-compatible —Functionally-compatible (FX2LP is a super set)

• Ultra Low power: I

—Ideal for bus and battery powered applications

• Software: 8051 code runs from:

—Internal RAM, which is downloaded via USB —Internal RAM, which is loaded from EEPROM —External memory device (128 pin package)

• 16 KBytes of on-chip Code/Data RAM

• Four programmable BULK/INTERRUPT/ISOCHRONOUS endpoints

—Buffering options: double, triple, and quad

• Additional programmable (BULK/INT ERRUPT) 64-byte endpoint

• 8- or 16-bit external data interface

• Smart Media Standard ECC generation

• GPIF (General Programmable Interface)

—Allows direct connection to most parallel interface

no more than 85 mA in any mode

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

—Programmable waveform descr iptors and configu-

ration registers to define waveforms

—Supports multiple Ready (RDY) inputs and Control

(CTL) outputs

• Integrate d, industry-standard enhanced 8051 —48-MHz, 24-MHz, or 12-MHz CPU operation —Four clocks per instructi on cycle —Two USARTS —Three counter/timers —Expanded interrupt system —Two data pointers

• 3.3V operation with 5V tolerant inputs

• Vectored USB interrupts and GPIF/FIFO interrupts

• Separ ate dat a buffe rs for the Set-u p and Data por tions

of a CONTROL transfer

• Integrated I

• Four integrated FIFOs —Integrated glue logic and FIFOs lower system cost

—Automatic conversion to and from 16-bit buses —Master or slave operation —Uses external clock or asynchronous strobes —Easy interface to ASIC and DSP ICs

• Avai lable in Commercial and Industrial temperature

grade (all packages except VFBGA)

C controller, runs at 100 or 400 kHz

Integrated

full- and high-s peed

XCVR

D+

D–

24 MHz Ext. XTAL

FX2LP

x20

VCC

PLL

1.5k connected f or

full speed

USB

2.0

XCVR

Enhanced USB core Simplifies 8051 code

/0.5 /1.0 /2.0

High-perfo rm ance micro using standard t ools with lower-power options

12/24/48 MHz,

four clocks/cycle

Smart

USB

1.1/2.0

Engine

Easy firmware change s

Figure 1-1. Block Diagram

Address (16)

8051 Core

16 KB

RAM

“Soft Conf iguratio n”

Data (8)

Additional I/Os (24)

GPIF

ECC

Address (16) / Data Bus (8)

4 kB

FIFO

FIFO and endpoint mem ory (master or s lav e operation )

Master

ADDR (9)

RDY (6) CTL (6)

8/16

Abundant I/O

including t w o USART S

General programm able I/F to ASIC/DSP or bus

standards such as ATAPI, EPP, etc.

Up to 96 MBytes/s

burst rate

Cypress Semiconductor Corporation • 198 Champion Court • San Jose, CA 95134-1709 • 408-943-2600 Document #: 38-08032 Rev. *K Revised January 26, 2006

Page 2

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

1.1 Features (CY7C68013A/14A only)

• CY7C68014A: Ideal for battery powered applications —Suspend current: 100 ∝A (typ)

• CY7C68013A: Ideal for non-battery powered appli ca-

tions

—Suspend current: 300 ∝A (typ)

• Ava ilable in five lea d-free packag es with up to 40 GPIOs —128-pin TQFP (40 GPIOs), 100-pin TQFP (40 GPIOs),

56-pin QFN (24 GPIOs), 56-pin SSOP (24 GPIOs), a nd 56-pin VFBGA (24 GPIOs)

1.2 Features (CY7C68015A/16A only)

• CY7C68016A: Ideal for battery powered applications —Suspend current: 100 ∝A (typ)

• CY7C68015A: Ideal for non-battery powered appli ca-

tions

—Suspend current: 300 ∝A (typ)

• Available in lead-free 56-pin QFN package (26 GPIOs) —2 more GPIOs than CY7C68013A/14A enabl ing addi -

tional features in same foot print

Cypress Semiconductor Corporation’s (Cypress’s) EZ-USB FX2LP (CY7C68013A/14A) is a low-power version of the EZ-USB FX2 (CY7C68013), which is a highly integrated, low-power USB 2.0 microcontroll er. By integr ating the USB 2.0 transceiver, serial interface engine (SIE), enhanced 8051 microcontroller, and a programmable peripheral interface in a single chip, Cypr ess has cr eated a ve ry cost -ef fec tive s oluti on that provides superior time-to-market advantages with low power to enable bus powered applications.

The ingenious architecture of FX2LP results in data transfer rates of over 53 Mbytes per second, the maximum-allowable USB 2.0 bandwid th, while still using a low-cost 8051 microcontroller in a package as small as a 56 VFBGA (5mm x 5mm). Because it incorporat es the USB 2.0 transcei ver , the FX2LP is more economical, providing a smaller footprint solution than USB 2.0 SIE or external transceiver implementations. With

EZ-USB FX2LP, the Cypress Smart SIE handles most of the USB 1.1 and 2.0 protocol in hardware, freeing the embedded microcontroller for application-specific functions and decreasing development time to ensure USB comp atibility.

The General Programmable Interface (GPIF) and Master/Slave Endpoint FIFO (8- or 16-bit data bus) provides an easy and glueless interface to popular interfaces such as ATA, UTOPIA, EPP, PCMCIA, and most DSP/processors.

The FX2LP draws considerably less current than the FX2 (CY7C68013), has double the on-chip code/data RAM and is fit, form and function compatible with the 56-, 100-, and 128-pin FX2.

Five package s are def ined for th e family: 56VFBGA, 56 SSOP, 56 QFN, 100 TQFP, and 128 TQFP.

2.0 Applications

• Portable video recorder

• MPEG/TV conversion

• DSL modems

• ATA interface

• Memory card reade rs

• Legacy conversion devices

• Cameras

• Scanners

• Home PNA

• Wireless LAN

• MP3 players

•Networking

The “Reference Designs” section of the Cypress web site provides addi tional tools for typical USB 2.0 applications. Each reference design comes complete with firmware source and object code, schematics, and documentation. Please visit http://www.cypress.com for more inform a tion.

Document #: 38-08032 Rev. *K Page 2 of 60

Page 3

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

3.0 Functional Overview

3.1 USB Signaling Speed

FX2LP operates at two of the three rates defined in the USB Specification Revision 2.0, dated April 27, 2000:

• Full speed, with a signaling bit rate of 12 Mbps

• High speed, with a signaling bit rate of 480 Mbps.

FX2LP does not support the low-speed signaling mode of

1.5 Mbps.

3.2 8051 Microprocessor

The 8051 microprocessor embedded in the FX 2LP family has 256 bytes of register RAM, an expanded interrupt system, three timer/counters, and two USARTs.

3.2.1 8051 Clock Frequency

FX2LP has an on-chip oscillator circuit that uses an external 24-MHz (±1 00-ppm) crystal with the following characteristics:

• Parallel resonant

• Fundamental mode

• 500-∝W drive level

• 12-pF (5% tolerance) load capacitors.

An on-chip PLL multiplies the 24-MHz oscillator up to 480 MHz, as required by the transceiver/PHY, and internal counters divide it down for use as the 8051 clock. The default 8051 clock frequency is 12 MHz. The clock frequency of the 8051 can be changed by the 8051 through the CPUCS register, dynamically.

24 MHz

12 pf

The CLKOUT pin, which can be three-stated and inverted using internal control bits, outputs the 50% duty cycle 8051 clock, at the selected 8051 clock frequency—48, 24, or 12 MHz.

3.2.2 USARTS

FX2LP contains two standard 8051 USARTs, addressed via Special Function Register (SFR) bits. The USART interface pins are available on separate I/O pins, and are not multiplexed with port pi ns.

UART0 and UART1 can operate using an internal clock at 230 KBaud with no more than 1% baud rate error. 230-KBaud operation i s achieved by an internal ly derived clo ck source that generates overflow pulses at the appropriate time. The internal clock adjust s for the 8051 clock rate (48, 24, 12 MHz) such that it always presents the correct frequency for 230-KBaud operati on.

3.2.3 Special Function Registers

Certain 8051 SFR addresses are populated to provide fast access to critical FX2LP functions. These SFR additions are shown in Table 3-1. Bold type indicates non-standard, enhanced 80 51 registers. The two SFR ro ws that end with “0” and “8” contain bit-addressable registers. The four I/O ports A–D use the SFR addresses used in the standard 8051 for ports 0–3, which are not implemented in FX2LP. Because of the faster and more efficient SFR addressing, the FX2LP I/O ports are not addressable in external RAM space (using the MOVX instruction).

[1]

3.3 I2C Bus

FX2LP supports the I2C bus as a master only at 10 0-/400-KHz. SCL and SDA pins have open-drain outputs and hysteresis inputs. These signal s must be pul led up t o 3.3V, even if no I device is connect ed.

3.4 Buses

20 × PLL

12-pF capacitor va lu es assume s a tr ac e ca pac i ta nc e

of 3 pF per side on a four-lay er F R4 P CA

Figure 3-1. Crystal Configuration

Note:

1. 115-KBaud operation is also possible by programming the 8051 SMOD0 or SMOD1 bits to a “1” for UART0 and/or UART1, respectively.

Document #: 38-08032 Rev. *K Page 3 of 60

All packages: 8- or 16-bit “FIFO” bidirectional data bus, multiplexed on I/O ports B and D. 128-pin package: adds 16-bit output-onl y 8051 address bus, 8-bit bi directional dat a bus.

Page 4

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 3-1. Special Function Registers

x8x 9x Ax Bx CxDxExFx

0 1SP EXIF 2DPL0 MPAGE 3DPH0 4 DPL1 5 DPH1 6 DPS 7PCON 8 TCON SCON0 IE IP T2CON EICON EIE EIP 9 TMOD SBUF0 ATL0AUTOPTRH1 EP2468STAT EP01STAT RCAP2L

BTL1AUTOPTRL1 EP24FIFOFLGS GPIFTRIG RCAP2H CTH0reserved EP68FIFOFLGS TL2 DTH1AUTOPTRH2 GPIFSGLDATH TH2 E CKCON AUTOPTRL2 GPIFSGLDATLX F reserved AUTOPTRSET-UP GPIFSGLDATLNOX

IOA IOB IOC IOD SCON1 PSW ACC B

INT2CLR IOE SBUF1 INT4CLR OEA

OEB OEC OED OEE

3.5 USB Boot Methods

During the power-up sequence, internal logic checks the I2C port for the connection of an EEPROM whose first byte is either 0xC0 or 0xC2. If found, it uses the VID/PID/DID values in the EEPROM in place of the inte rnally store d values (0xC0) , or it boot-loads the EEPROM contents into internal RAM (0xC2). If no EEPROM is detected, FX2LP enumerates using internally sto red descriptors. The defaul t ID val ues for FX2LP are VID/PID/DID (0x04B4, 0x8613, 0xAxxx where xxx = Chip revision).

T able 3-2. Default ID V alues for FX2LP

Vendor ID 0x04B4 Cypress Semiconductor Product ID 0x8613 EZ-USB FX2LP Device release 0xAnnn Depends on chi p revision

[2]

Default VID/PID/DID

(nnn = chip revision where first silicon = 001)

3.6 ReNumeration™

Because the FX2LP’s configuration is soft, one chip can take on the identities of multiple distinct USB devices.

When first p lugged into USB, the FX2LP enumerates automatically and down loa ds firmware and USB des cript or t ab les ov er the USB cable. Next, the FX2LP enumerates again, this time as a device defined by the downloaded information. This patented two-step process, called ReNumeration, happens instantly when the device is plugged in, with no hint that the initial download step has occurred.

Two control bits in the USBCS (USB Control and Status) register control the ReNumeration process: DISCON and

RENUM. To simulate a USB disconnect, the firmware sets DISCON to 1. To reconnect, the fir mware clear s DISCON to 0.

Before reconnecting, the firmware sets or clears the RENUM bit to indi cate whet her the f irmware or the Default USB Dev ice will handle de vi ce reques ts ov er endpoi nt zer o: if RENUM = 0, the Default USB Device will handl e device r equests; if RENUM = 1, the firmware will.

3.7 Bus-powered Applications

The FX2LP fully supports bus-powered designs by enumerating with less than 100 m A as requi red by t he USB 2.0 spec ification.

3.8 Inter rupt Syst em

3.8.1 INT2 Interrupt Request and Enable Registers

FX2LP implements an autovector feature for INT2 and INT4. There are 27 INT2 (USB) vectors, and 14 INT4 (FIFO/GPIF) vectors. See EZ-USB Technical Reference Manual (TRM) for more detail s.

3.8.2 USB-Interrupt Autovectors

The main USB interrupt is shared by 27 interrupt sources. To save the code and processing time that normally would be required to identify the individual USB interrupt source, the FX2LP provides a second level of interrupt vectoring, called Autovectoring. When a USB interrupt is asserted, the FX2LP pushes the program counter onto its stack then jumps to address 0x0043, where it expects to find a “jump” instruction to the USB Interrupt serv ice routine.

ote:

2. The I

Document #: 38-08032 Rev. *K Page 4 of 60

C bus SCL and SDA pins must be pulled up, even if an EEPROM is not connected. Otherwise this detection method does not work properly.

Page 5

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

The FX2LP jump instruction is encoded as follows.

Table 3-3. INT2 USB Interrupts

USB INTERRUPT TABLE FOR INT2

Priority INT2VEC Val ue Source Notes

1 00 SUDAV Set-up Data Available 2 04 SOF Start of Frame (or microframe) 3 08 SUTOK Set-up Token Received 4 0C SUSPEND USB Suspend request 5 10 USB RESET Bus reset 6 14 HISPEED Entered high speed operation 7 18 EP0ACK FX2LP ACK’d the CONTROL Handshake 8 1C reserved 9 20 EP0-IN EP0-IN ready to be loaded with data

10 24 EP0-OUT EP0-OUT has USB data

11 28 EP1-IN EP1-IN ready to be loaded with data 12 2C EP1-OUT EP1-OUT has USB data 13 30 EP2 IN: buffer available. OUT: buffer has data 14 34 EP4 IN: buffer available. OUT: buffer has data 15 38 EP6 IN: buffer available. OUT: buffer has data 16 3C EP8 IN : buf fer available. OUT: buffer has data 17 40 IBN IN-Bulk-NAK (any IN endpoint) 18 44 reserved 19 48 EP0PING EP0 OUT was Pinged and it NAK’d 20 4C EP1PING EP1 OUT was Pinged and it NAK’d 21 50 EP2PING EP2 OUT was Pinged and it NAK’d 22 54 EP4PING EP4 OUT was Pinged and it NAK’d 23 58 EP6PING EP6 OUT was Pinged and it NAK’d 24 5C EP8PING EP8 OUT was Pinged and it NAK’d 25 60 ERRLIMIT Bus errors exceeded t he programmed limit 26 64 27 68 reserved 28 6C reserved 29 70 EP2ISOERR ISO EP2 OUT PID sequence error 30 74 EP4ISOERR ISO EP4 OUT PID sequence error 31 78 EP6ISOERR ISO EP6 OUT PID sequence error 32 7C EP8ISOERR ISO EP8 OUT PID sequence error

If Autovectoring is enabled (AV2EN = 1 in the INTSET-UP register), t he FX2LP substitutes i ts INT2VEC byte. Therefore, if the high byte (“page”) of a jump-table address is preloaded at location 0x0044, the automatically-inserted INT2VEC byte at 0x0045 wil l direct the jump to the correct address out of the 27 addresses within the page.

Document #: 38-08032 Rev. *K Page 5 of 60

3.8.3 FIFO/GPIF Inte rrupt (INT4)

Just as the USB Interrupt is shared among 27 individual USB-interrupt sources, the FIFO/GPIF interrupt is shared among 14 individual FIFO/GPIF sources. The FIFO/GPIF Interrupt, like the USB Interrupt, can employ autovectoring. Table 3-4 shows the priority and INT4VEC values for the 14 FIFO/GPIF interrupt sources.

Page 6

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 3-4. Individual FIFO/GPIF Interrupt Sources

Priority INT4VEC Value Source Notes

1 80 EP2PF Endpoint 2 Programmable Flag 2 84 EP4PF Endpoint 4 Programmable Flag 3 88 EP6PF Endpoint 6 Programmable Flag 4 8C EP8PF Endpoint 8 Programmable Flag 5 90 EP2EF Endpoint 2 Empty Flag 6 94 EP4EF Endpoint 4 Empty Flag 7 98 EP6EF Endpoint 6 Empty Flag 8 9C EP8EF Endpoint 8 Empty Flag

9 A0 EP2FF Endpoint 2 Full Fl ag 10 A4 EP4FF Endpoint 4 Full Flag 1 1 A8 EP6FF Endpoint 6 Full Flag 12 AC EP8FF Endpoint 8 Full Flag 13 B0 GPIFDONE GPIF Operation Complete 14 B4 GPIFWF GPIF Waveform

If Autovectoring is enabled (AV4EN = 1 in the INTSET-UP register), t he FX 2LP s ubst itutes its I NT4VEC by te. The refor e, if the high byte (“page”) of a jump-table address is preloaded at location 0x0054, the automatically-inserted INT4VEC byte at 0x0055 wil l direct the jump to the correct address out of the 14 addresses within the page. When the ISR occurs, the FX2LP pushes the program counter onto its stack then jumps to address 0x 0053, where it expect s to f ind a “j ump” inst ruction to the ISR Interrupt se rvi ce routine.

3.9 Reset and Wakeup

3.9.1 Reset Pin

The input pin, RESET#, will reset the FX2LP when asserted. This pin has hysteresis and is active LOW. When a crystal is

used with t he CY7C680x xA t he rese t period must al low f or th e stabilization of the crystal and the PLL. This reset period should be approxi m ately 5 ms after VCC has reac hed 3.0V. If the cryst al in put pin is dri ven by a c loc k signal the i ntern al PLL stabilizes in 200 ∝s after VCC has reached 3.0V shows a power-on reset condition and a reset applied during operation. A power-on reset is defined as the time reset is asserted while power is being appl ied to the circ uit. A powered reset is defined to be when the FX2LP has previously been powered on and operating and the RESET# pin is asserted.

Cypress provides an application note which describes and recommends power on reset implementat ion and can be found on the Cypress web s ite. For more i nformat io n on reset implementation for the FX2 family of products visit the http://www.cypress.com.

[3]

. Figure 3-2

Note:

3. If the external clock is powered at the same time as the CY7C680xxA and has a stabilization wait period, it must be added to the 200 ∝s.

Document #: 38-08032 Rev. *K Page 6 of 60

Page 7

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

RESET#

3.3V

3.0V

VCC

RESET

Power on Res et

Figure 3-2. Reset Timing Plots

Table 3-5. Reset Timing Values

Condition T

Power-on Reset with crystal 5 ms Power-on Reset with external

clock Powered Reset 200 ∝s

3.9.2 Wakeup Pins

The 8051 puts itself and the re st of the chip into a power-down mode by setting PCON.0 = 1. This stops the oscillator and PLL. When WAKEUP is asserted by external logic, the oscillator restarts, after the PLL stabilizes, and then the 8051 receives a wakeup interrupt. This applies whether or not FX2LP is connected to the USB.

The FX2LP exits the power-down (USB suspend) state using one of the following meth ods:

• USB bus activity (if D+/D– lines are lef t floating, noise on these lines may i ndicate activ ity to the FX2LP and i nitiate a wakeup).

• External l ogic asserts the WAKEUP pin

• Externa l l ogic asserts the PA3/WU2 pin.

The second wakeup pin, WU2, can also be configured as a general purpose I/O pin. This allows a simple external R-C network to be used as a periodic wakeup source. Note that WAKEUP is by default active LOW.

200 ∝s + Clock stabili ty tim e

RESET

RESET#

3.3V

VCC

RESET

Powered Reset

3.10 Program/Data RAM

3.10.1 Size

The FX2LP has 16 KBytes of internal program/data RAM, where PSEN#/RD# signals are internally ORed to allow the 8051 to access it as both program and dat a m em ory. No USB control registers appear in this space.

Two memory maps are shown in the following diagrams:

Figure 3-3 Internal Code Memory, EA = 0 Figure 3-4 External Code Memory, EA = 1.

3.10.2 Internal Code Memory, EA = 0

This mode implements the internal 16-KByte block of RAM (starting at 0) as combined code and data memory. When external RAM or ROM is added, the external read and write strobes are suppressed for memory spaces that exist inside the chip. This allows the user to connect a 64-KByte memory without requiring address decodes to keep clear of internal memory spaces.

Only the internal 16 KBytes and scratch p ad 0.5 KByt es RAM spaces have the following access:

• USB download

• USB upload

• Set-up data poi nter

•I

C interface boot loa d.

3.10.3 External Code Memory, EA = 1

The bottom 16 KBytes of program memory is external, and therefore the bottom 16 KBytes of internal RAM is accessible only as data memory.

Document #: 38-08032 Rev. *K Page 7 of 60

Page 8

A A

Inside FX2LP Outside FX2LP

FFFF

4K FIFO buffers

E200 E1FF

0.5 KBytes RAM

Data (RD#,WR#)*

E000

3FFF

7.5 KBytes USB regs and

(RD#,WR#)

(OK to populate data memory here—RD#/WR# strobes are not active)

40 KBytes External Data Memory (RD#,WR#)

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

48 KBytes External Code Memory (PSEN#)

16 KBytes RAM Code and Data (PSEN#,RD#,WR#)*

0000

(Ok to populate data memory here—RD#/WR# strobes are not active)

Data Code

(OK to populate program memory here— PSEN# strobe is not active)

*SUDPTR, USB upload/download, I2C interface boot access

Figure 3-3. Internal Code Memory, EA = 0

Inside FX2LP Outside FX2LP

FFFF

4K FIFO buffers

E200 E1FF

0.5 KBytes RAM

Data (RD#,WR#)*

E000

3FFF

7.5 KBytes USB regs and

(RD#,WR#)

(OK to populate data memory here—RD#/WR# strobes are not active)

40 KBytes External Data Memory (RD#,WR#)

64 KBytes External Code Memory (PSEN#)

(Ok to populate data memory here—RD#/WR# strobes are not active)

Data Code

0000

16 KBytes RAM Data (RD#,WR#)*

*SUDPTR, USB upload/download, I2C interface boot access

Figure 3-4. External Code Memory, EA = 1

Document #: 38-08032 Rev. *K Page 8 of 60

Page 9

A A

3.11 Register Addresses

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

FFFF

F000 EFFF

E800 E7FF

E7C0 E7BF

E780 E77F

E740

E73F

E700 E6FF

E500 E4FF E480 E47F

E400

E3FF E200

E1FF

E000

4 KBytes EP2-EP8

2 KBytes RESERVED

64 Bytes EP1IN

64 Bytes EP1OUT

64 Bytes EP0 IN/OUT

64 Bytes RESERVED

8051 Addressable Registers

Reserved (128)

128 bytes GPIF Waveforms

Reserved (512)

512 bytes

8051 xdata RAM

buffers

(8 x 512)

(512)

3.12 Endpoint RAM

3.12.1 Size

• 3× 64 bytes (Endpoints 0 and 1)

• 8 × 512 bytes (Endpoints 2, 4, 6, 8)

3.12.2 Organization

• EP0

• Bidirect ional endpoint zero, 64-byte buffer

• EP1IN, EP1OUT

• 64-byte buffers, bulk or int errupt

• EP2,4,6,8

• Eight 512- byte buff ers, bulk, i nterrup t, or isochr onous. EP4 and EP8 can be double buffe red, while EP2 and 6 can be either double, tr iple , or quad buff er ed. For high- speed endpoint configuration options, see Figure 3- 5.

3.12.3 Set-up Data Buffer

A separate 8-byte buffer at 0xE6B8-0xE6BF holds the Set-up data from a CONTROL transfer.

3.12.4 Endpoint Configurations (H igh-speed Mode)

Endpoints 0 and 1 are the same for every configuration. Endpoint 0 is the only CONTROL endpoint, and end point 1 can be either BULK or INTERRUPT. The endpoint buffers can be configured in any 1 of the 12 configurations shown in the vertical columns. When operating in full-speed BULK mode only the first 64 bytes of each buffer a re used. For example in high-speed, the max packet size is 512 bytes but in full-speed it is 64 bytes. Even though a buffer is configured to be a 512 byte buffer, in full-speed only the first 64 bytes are used. The unused end point buffer space is not available for other operations. An example endpoint configuration would be:

Document #: 38-08032 Rev. *K Page 9 of 60

Page 10

A A

EP2–1024 double buffered; EP6–512 quad buffered

(column 8).

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

EP0 IN&OUT

EP1 IN

EP1 OUT

64 64 64

EP2

512

EP4

512

EP6

512 512

EP8

512

64 64 64

EP2

512 512

EP4

512 512

EP6

512 512

512

64 64 64

EP2

512 512

EP4

512 512

EP6

1024

EP2

512

EP6

512

EP8

512

64 64 64

EP2

512 512

EP6

1024

64 64 64

EP2

1024

EP6

512 512

EP8

512 512

64 64 64

EP2

1024

EP6

512 512

512

64 64 64

EP2

1024

EP6

1024

64 64 64

EP2

512

EP6

512

EP8

512 512

64 64 64

EP2

1024

EP8

512 512

64 64 64

EP2

1024

Figure 3-5. Endpoint Configuration

3.12.5 Default Full-Speed Alternate Settings

T able 3-6. Default Full-Speed Alternate Settings

[4, 5]

Alternate Setting 0 1 2 3

ep0 64 64 64 64 ep1out 0 64 bulk 64 int 64 int ep1in 0 64 bulk 64 int 64 int ep2 0 64 bulk out (2×) 64 int out (2×) 64 iso out (2×) ep4 0 64 bulk out (2×) 64 bulk out (2×) 64 bulk out (2×) ep6 0 64 bulk in (2×) 64 int in (2×) 64 iso in (2×) ep8 0 64 bulk in (2×) 64 bulk in (2×) 64 bulk in (2×)

3.12.6 Default High-Speed Alternate Settings

T able 3-7. Default High-Speed Alternate Settings

[4, 5]

Alternate Setting 0 1 2 3

ep0 64 64 64 64 ep1out 0 512 bulk ep1in 0 512 bulk

[6] [6]

64 int 64 int

64 int 64 int ep2 0 512 bulk out (2×) 512 int out (2×) 512 iso out (2×) ep4 0 512 bulk out (2×) 512 bulk out (2×) 512 bulk out (2×) ep6 0 512 bulk in (2×) 512 int in (2×) 512 iso in (2×) ep8 0 512 bulk in (2×) 512 bulk in (2×) 512 bulk in (2×)

otes:

4. “0” means “not implemented.”

5. “2×” means “double buffered.”

6. Even though these buffers are 64 bytes, they are reported as 512 for USB 2.0 compliance. The user must never transfer packets larger than 64 bytes to EP

Document #: 38-08032 Rev. *K Page 10 of 60

Page 11

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

3.13 Extern al FIF O Interface

3.13.1 Architecture

The FX2LP slave FIFO ar chi tect ure has ei ght 512 -by te bloc ks in the endpoint RAM that directly serve as FIFO memories, and are controlled by FIFO control signals (such as IFCLK, SLCS#, SLRD, SLWR, SLOE, PKTEND, and flags).

In operation, some of the eight RAM blocks fill or empty from the SIE, while the others are connected to the I/O transfer logic. The transf er logic tak es two forms, the GPIF f or internally generated control signals, or the slave FIFO interface for externally controlled transfers.

3.13.2 Master/Slave Control Signals

The FX2LP endpoint FIFOS are implemented as eight physically distinct 256x16 RAM blocks. The 8051/SIE can switch any of the RAM blocks between two domains, the USB (SIE) domain and the 8051-I/O Unit domain. This switching is done virtually instantaneously, giving essentially zero transfer time between “USB FIFOS” and “Slave FIFOS.” Since they are physically the same memory, no bytes are actua lly t ransf erred between buffer s.

At any given time, some RAM blocks are filling/emptying with USB data under SIE control, while other RAM blocks are available to the 8051 and/or the I/O control unit. The RAM blocks operate as single-port in the USB domain, and dual-port in the 8051-I/O domain. The blocks can be configured as single, doubl e, triple, o r quad buffered as previously shown.

The I/O control unit implements either an internal-master (M for master) or external-master (S for Slave) interface.

In Master (M) mode, the GPIF internally controls FIFOADR[1..0] to select a FIFO. The RDY pins (two in the 56-pin package, six in the 100 -pin and 128- pin packages) can be used as flag inputs from an external FIFO or other logic if desired. The GPI F ca n be run from ei the r an in ternal ly der ived clock or externally supplied clock (IFCLK), at a rate that transfers data up to 96 Megabytes/s (48-MHz IFCLK with 16-bit interface).

In Slave (S) mode, the FX2LP accepts either an internally derived clock or externally supplied clock (IFCLK, max. frequency 48 MHz) and SLCS#, SLRD, SLWR, SLOE, PKTEND signals from external logic. When using an external IFCLK, the external clock m ust be pres ent before switching to the external clock with the IFCLKSRC bit. Each endpoint can individually be selected for byte or word operation by an internal configuration bit, and a Slave FIFO Output Enable signal SLOE ena ble s dat a o f the se lected widt h. Ex ternal logi c must insure that the output enable signal is inactive when writing data to a slave FIFO. The slave interface can also operate asynchronously, where the SLRD and SLW R signals act directly as strobes, rather than a clock qualifier as in synchronous mode. The signals SLRD, SLWR, SLOE and PKTEND are gated by the signal SLCS#.

3.13.3 GPIF and FIFO Clock Rates

An 8051 register bit selects one of two frequencies for the internal ly supplied interface clock: 30 M H z and 48 M Hz. Alternatively, an externally supplied clock of 5 MHz–48 MHz feeding the IFCLK pin can be used as the interface clock. IFCLK can be configured to function as an output clock when the GPIF and FIFOs are internally clocked. An output enable bit in the IFCONFIG register turns this clock output off, if desired. Anothe r bit with in the IF CONFIG re gister w ill invert the IFCLK signal whether internally or externally sourced.

3.14 GPIF

The GPIF is a flex ible 8- or 1 6-bit paral lel i nterface driven by a user-programmable finite state machine. It allows the CY7C68013A/15A to perform local bus mastering, and can implement a wide variety of protocols such as ATA interface, printer pa ral lel port, and Utopia.

The GPIF has six programmable control outputs (CTL), nine address outputs (GPIFADRx), and six general-purpose ready inputs (RDY). The data bus width can be 8 or 16 bits. Each GPIF vector def ines the st ate of the control output s, and det ermines what state a ready input (or multiple inputs) must be before proceeding. The GPIF vector can be programmed to advance a FIFO to the next data value, advance an address, etc. A sequence of the GPIF vectors make up a single waveform that will be executed to perform the desired data move between the FX2LP and the external device.

3.14.1 Six Control OUT Signals

The 100- and 128-pin pa ckages bring out all six Control Output pins (CTL0-CTL5) . The 8051 progr ams the GPIF unit to def ine the CTL waveforms. The 56-pin package brings out three of these signals, CTL0–CTL2. CTLx waveform edges can be programmed to make transitions as fast as once per clock (20.8 ns using a 48-MHz cl ock).

3.14.2 Six Ready IN Signals

The 100- and 128-pin packages bring out all six Ready inputs (RDY0–RDY5). The 8051 programs the GPIF unit to test the RDY pins for GPIF branching. The 56-pin package brings out two of these signals, RDY0–1.

3.14.3 Nine GPIF Address OUT Signals

Nine GPIF address l ines are availa ble in the 100- and 128- pin packages, GPIFADR[8..0]. The GPIF address lines allow indexing through up to a 512-byte block of RAM. If more address lines are needed, I/O port pins can be used.

3.14.4 Long Transfer Mode

In master mode, the 8 051 appropr iate ly set s GPI F trans actio n count registers (GPIFTCB3, GPIFTCB2, GPIFTCB1, or GPIFTCB0) for unatte nded transf ers of up to 2 The GPIF automatical ly throt tles dat a flow to prevent under or overflow until the full number of requested transactions complete. The GPIF decrements the value in these registers to represent the current status of the transaction .

transacti ons.

Document #: 38-08032 Rev. *K Page 1 1 of 60

Page 12

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

3.15 ECC Gen erati on

[7]

The EZ-USB can calc ulate ECCs (Err or-Cor recting Co des) on data that passes across its GPIF or Slave FIFO interfaces. There are two ECC configurations: Two ECCs, each calculated over 256 bytes (SmartMedia Standard); and one ECC calculated over 512 bytes.

The ECC can correct any one-bit error or detect any two-bit error.

3.15.1 ECC Implementation

The two ECC configurations are selected by the ECCM bit:

3.15.1.1 ECCM = 0

Two 3-byte ECCs, each calculated over a 256-byte block of data. This configuration conforms to the SmartMedia Standard.

Write any value to ECCRESET, then pass data across the GPIF or Slave FI FO interface. The ECC for the f ir st 256 bytes of data will be calculat ed and stored in ECC1. The ECC for the next 256 bytes will be stored in ECC2. After the second ECC is calculated, the values in the ECCx registers will not change until ECCRESET is written agai n, even if more data is subsequently passed across the interface.

3.15.1.2 ECCM = 1

One 3-byte ECC calculated over a 512-byte block of data. Write any value to ECCRESET then pass data across the

GPIF or Slave FI FO interface. The ECC for the f ir st 512 bytes of data will be calcul ated and stored in ECC1; ECC2 is unused. After the ECC is cal culat ed, t he value i n ECC1 wil l not ch ange until ECCRESET is written agai n, even if more data is subsequently passed across the interface

3.16 USB Uploads and Downlo ads

The core has the abi lit y to di rect ly edi t the dat a content s of t he internal 16-KByte RAM and of the internal 512-byte scratch pad RAM via a vendor-specific command. This capability is normally used when “soft” downloading user code and is available only to and from internal RAM, only when the 8051 is held in reset. The availab le RAM spaces ar e 16 KBytes fro m 0x0000–0x3FFF (code/data) and 512 bytes from 0xE000–0xE1FF (scrat ch pad data RAM).

[8]

3.17 Autopo inter Access

FX2LP provides t wo ident ical a utopoi nters. They are simi lar to the internal 8051 data pointers, but with an additional feature: they can opt ionally increment after every m emory acces s. This capability is available to and from both internal and external RAM. The autopointers are available in external FX2LP registers, under control of a mode bit (AUTOPTRSET-UP.0). Using the external FX2LP autopointer access (at 0xE67B – 0xE67C) allows the autopointer to access all RAM, internal and external to the p art. Also, the a utopointers can point to any FX2LP register or endpoint buffer space. When autopointer access to external memory is enabled, location 0xE67B and 0xE67C in XDATA and code space cannot be used.

3.18 I2C Controller

FX2LP has one I2C port that is driven by two internal controllers, one that automatically operates at boot time to load VID/PID/DID and configuration information, and another that the 8051, once running, uses to control external I devices. The I

3.18.1 I

C pins SCL and SDA must have exter nal 2.2-k. pull-up

The I

C port operates in master mode only.

C Port Pins

resistors even if no EEPROM is connected to the FX2LP. External EEPROM device address pins must be configured properly. See Table 3-8 for configuring the device address pins.

T able 3-8. Strap Boot EEPROM Address Lines to These Values

Bytes Example EEPROM A2 A1 A0

16 24LC00

[9]

N/A N/A N/A 128 24LC01 0 0 0 256 24LC02 0 0 0 4K 24LC32 0 0 1 8K 24LC64 0 0 1 16K 24LC128 0 0 1

3.18.2 I

At power-on reset the I

C Interface Boot Load Access

C interface boot loader will load the VID/PID/DID configuration bytes and up to 16 KBytes of program/data. The ava il able RAM spaces are 16 KByt es from 0x0000–0x3FFF and 512 bytes from 0xE000–0xE1FF. The 8051 will be in reset. I

C interface boot loads only occur after

power-on reset .

3.18.3 I

The 8051 can control peripherals connected to the I using the I2CTL and I2DAT registers. FX2LP provides I master control only, it is never an I

C Interface General-Purpose Access

C slave.

C bus

3.19 Compatible with Previous Generation EZ-USB FX2

The EZ-USB FX2LP is form/fit and with minor exceptions functionall y compatibl e with its pre decessor , the EZ-USB FX2. This makes for an easy transition for designers wanting to upgrade their systems from the FX2 to the FX2LP. The pinout and package selection are identical, and the vast majority of firmware previously developed for the FX2 will function in the FX2LP.

For designers migrating from the FX2 to the FX2LP a change in the bill o f materi al and review o f the mem ory al locat ion (du e to increas ed int ernal memory ) is requ ired for mor e info rmat ion about migrating fr om EZ-US B FX2 to EZ-USB FX2LP, please see further details in the application note titled Migrating from EZ-USB FX2 to EZ-USB FX2LP, which is available on the Cypress Webs it e.

Notes:

7. To use the ECC logic, the GPIF or Slave FIFO interface must be configured for byte-wide operation.

8. After the data has been downloaded from the host, a “loader” can execute from internal RAM in order to transfer downloaded data to external memory.

9. This EEPROM does not have address pins.

Document #: 38-08032 Rev. *K Page 12 of 60

Page 13

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

T able 3-9. Part Number Conversion Table

EZ-USB FX2

Part Number

CY7C68013-56PVC CY7C68013A-56PVXC or CY7C68014A-56PVXC 56-pin SSOP

CY7C68013-56PVCT CY7C68013A-56PVXCT or CY7C68014A-56PVXCT 56-pin SSOP – Tape and Reel

CY7C68013-56LFC CY7C6801 3A-56LFXC or CY7C68014A-56LFXC 56-pin QFN CY7C68013-100AC CY7C68013A-100AXC or CY7C68014A-100AXC 100-pin TQFP CY7C68013-128AC CY7C68013A-128AXC or CY7C68014A-128AXC 128-pin TQFP

EZ-USB FX2LP

Part Number Package Description

3.20 CY7C68 013A/ 14A and CY7C68 015A/16A Differences

CY7C68013A is identical to CY7C68014A in form, fit, and functionality. CY7C68015A is identical to CY7C68016A in form, fit, and functionality. CY7C68014A and CY7C68016A have a lower suspend current than CY7C68013A and CY7C68015A respectively. CY7C68014A and CY7C68016A have a lower suspend current than CY7C68013A and CY7C68015A respectively: hence are ideal for power-sensitive battery applications.

CY7C68015A and CY7C68016A are available in 56-pin QFN package only. Two additional GPIO signals are available on the CY7C68015A and CY7C68016A to provide mo re flexibility when neither IFCLK or CLKOUT are needed in the 56-pin

package. The USB developers who want to convert their FX2 56-pin appli cation to a bus-powered syst em will directly benefit from these additional signals. The two GPIOs will give these developers the signals they need for the power cont rol circuitry of their bus-powered application without pushing them to a high-pincount version of FX2LP. The CY7C68015A is only available in the 56-pin QFN package

Table 3-10. CY7C68013A/14A and CY7C68015A/16A Pin Differences

CY7C68013A/CY7C68014A CY7C68015A/CY7C68016A

IFCLK PE0/T0OUT

CLKOUT PE1/T1OUT

Document #: 38-08032 Rev. *K Page 13 of 60

Page 14

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

4.0 Pin Assignments

Figure 4-1 identifi es all signa ls for the f ive packag e ty pes. The following pages illustrate the individual pin diagrams, plus a combination diagram showing which of the full set of signals are available in the 128-, 100-, and 56-pin packages.

The signals on the left edge of the 56-pin package in Figure 4-1 are common to all versions in the FX2LP family wi th the noted differences between the CY7C68013A and the CY7C68015A. Three modes are available in all package versions: Port, GPIF master, and Slave FIFO. These modes define the signals on the right edge of the diagram. The 8051 selects the interface mode using the IFCONFIG[1:0] register bits. Port mode is the power-on default configuration.

The 100-pin packag e adds fu nctio nalit y to the 56-pi n pac kage by adding these pins:

• PORTC or alternate GPIFADR[7:0] address signals

• PORTE or al ternate GPIF ADR[8] address si gnal and seven additional 8051 signals

• Three GPIF Control signals

• Four GPIF Ready signals

• Nine 8051 signals (two USARTs, three timer inputs, INT4,and INT5#)

• BKPT, RD#, WR#.

The 128-pin package adds the 8051 address and data buses plus control si gnals. Note that two of the requir ed signals, RD# and WR#, are present in the 100-pin version. In the 100-pin and 128-pin versions, an 8051 control bit can be set to pulse the RD# and WR# pins when the 8051 reads from/writes to PORTC. This feature is enabled by setting PORTCSTB bit in CPUCS register.

Section 10.5 displ ays the timing di agram of the read and wri te strobing function on accessing PORTC.

Document #: 38-08032 Rev. *K Page 14 of 60

Page 15

A A

Port GPIF Master Slave FIFO

XTALIN XTALOUT RESET# WAKEUP#

SCL SDA

**PE0 replaces IFCLK

& PE1 replaces CLKOUT on CY7C68015A

**PE0/T0OUT **PE1/T1OUT

IFCLK CLKOUT

DPLUS DMINUS

100

BKPT PORTC7/GPIFADR7

PORTC6/GPIFADR6 PORTC5/GPIFADR5 PORTC4/GPIFADR4 PORTC3/GPIFADR3 PORTC2/GPIFADR2 PORTC1/GPIFADR1 PORTC0/GPIFADR0

PE7/GPIFADR8 PE6/T2EX PE5/INT6 PE4/RxD1OUT PE3/RxD0OUT PE2/T2OUT PE1/T1OUT PE0/T0OUT

D7 D6 D5 D4 D3 D2 D1 D0

128

** pinout for CY7C68015A/CY7C680 16A only

FD[15]

PD7

FD[14]

PD6

FD[13]

PD5

FD[12]

PD4

FD[11]

PD3

FD[10]

PD2

FD[9]

PD1

FD[8]

PD0

FD[7]

PB7

FD[6]

PB6

FD[5]

PB5

FD[4]

PB4

FD[3]

PB3

FD[2]

PB2

FD[1]

PB1

FD[0]

PB0

RDY0 RDY1

CTL0 CTL1 CTL2

INT0#/PA0 INT1#/PA1

WU2/PA3

Figure 4-1. Signals

PA2 PA4

PA5 PA6 PA7

RxD0

TxD0

RxD1

TxD1

INT4

INT5#

T2 T1 T0

RD#

WR#

CS# OE#

PSEN#

A15 A14 A13 A12 A11 A10

A9 A8 A7 A6 A5 A4 A3 A2 A1 A0

INT0#/PA0 INT1#/PA1 PA2 WU2/PA3 PA4 PA5 PA6 PA7

CTL3 CTL4 CTL5 RDY2 RDY3 RDY4 RDY5

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

FD[15] FD[14] FD[13] FD[12] FD[11] FD[10] FD[9] FD[8] FD[7] FD[6] FD[5] FD[4] FD[3] FD[2] FD[1] FD[0]

SLRD SLWR

FLAGA FLAGB FLAGC

INT0#/ PA0 INT1#/ PA1 SLOE WU2/PA3 FIFOADR0 FIFOADR1 PKTEND PA7/FLAGD/SLCS#

Document #: 38-08032 Rev. *K Page 15 of 60

Page 16

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

PD1/FD9

PD2/FD10

PD3/FD11

INT5#

VCC

PE0/T0OUT

PE1/T1OUT

PE2/T2OUT

PE3/RXD0OUT

PE4/RXD1OUT

PE5/INT6

PE6/T2EX

PE7/GPIFADR8

GND

PD4/FD12

PD5/FD13

PD6/FD14

PD7/FD15

GND

A10

CLKOUT

VCC

GND

RDY0/*SLRD

RDY1/*SLWR

RDY2

RDY3

RDY4

RDY5

AVCC

XTALOUT

XTALIN

AGND

AVCC

DPLUS

DMINUS

AGND

A11

A12

A13

A14

A15

VCC

GND

INT4

*IFCLK

RESERVED

BKPT

SCL

SDA

OE#

A3 A2 A1 A0

D7 D6 D5

102 101 100

99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65

PD0/FD8

*WAKEUP

VCC

RESET#

CTL5

GND

PA7/*FLAGD/SLCS#

PA6/*PKTEND PA5/FIFOADR1 PA4/FIFOADR0

CY7C68013A/CY7C68014A

128-pin TQFP

PA3/*WU2

PA2/*SLOE

PA1/INT1# PA0/INT0#

VCC

GND PC7/GPIFADR7 PC6/GPIFADR6 PC5/GPIFADR5 PC4/GPIFADR4 PC3/GPIFADR3 PC2/GPIFADR2 PC1/GPIFADR1 PC0/GPIFADR0

CTL2/*FLAGC CTL1/*FLAGB CTL0/*FLAGA

VCC CTL4 CTL3

PSEN#

WR#

RD#

PB0/FD0

RXD0

TXD0

GND

VCC

CS#

VCC

PB3/FD3

PB2/FD2

PB1/FD1

PB4/FD4

RXD1

TXD1

GND

VCC

PB7/FD7

PB6/FD6

PB5/FD5

GND

Figure 4-2. CY7C68013A/CY7C68014A 128-pin TQFP Pin Assignment

* denotes programmable polarity

Document #: 38-08032 Rev. *K Page 16 of 60

Page 17

A A

100

CLKOUT

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

PD1/FD9

PD2/FD10

PD3/FD11

INT5#

VCC

PE0/T0OUT

PE1/T1OUT

PE2/T2OUT

PE3/RXD0OUT

PE4/RXD1OUT

PE5/INT6

PE6/T2EX

PE7/GPIFADR8

GND

PD4/FD12

PD5/FD13

PD6/FD14

PD7/FD15

GND

VCC

GND

RDY0/*SLRD

RDY1/*SLWR

RDY2

RDY3

RDY4

RDY5

AVCC

XTALOUT

XTALIN

AGND

AVCC

DPLUS

DMINUS

AGND

VCC

GND

INT4

*IFCLK

RESERVED

BKPT

SCL

SDA

CY7C68013A/CY7C68014A

100-pin TQFP

PD0/FD8

*WAKEUP

VCC

RESET#

CTL5

GND

PA7/*FLAGD/SLCS#

PA6/*PKTEND PA5/FIFOADR1 PA4/FIFOADR0

PA3/*WU2

PA2/*SLOE

PA1/INT1# PA0/INT0#

VCC

GND PC7/GPIFADR7 PC6/GPIFADR6 PC5/GPIFADR5 PC4/GPIFADR4 PC3/GPIFADR3 PC2/GPIFADR2 PC1/GPIFADR1 PC0/GPIFADR0

CTL2/*FLAGC CTL1/*FLAGB CTL0/*FLAGA

VCC CTL4 CTL3

80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51

PB4/FD4

RXD1

TXD1

GND

VCC

RD#

WR#

VCC

PB3/FD3

PB2/FD2

PB1/FD1

PB0/FD0

RXD0

TXD0

GND

VCC

PB7/FD7

PB6/FD6

PB5/FD5

Figure 4-3. CY7C68013A/CY7C68014A 100-pin TQFP Pin Assignment

* denotes programmab le pol arity

Document #: 38-08032 Rev. *K Page 17 of 60

Page 18

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

CY7C68013A/CY7C68014A

56-pin SSOP

PD5/FD13

PD6/FD14

PD7/FD15

GND

CLKOUT/T1OUT

VCC

GND

RDY0/*SLRD

RDY1/*SLWR

AVCC

XTALOUT

XTALIN

AGND

AVCC

DPLUS

DMINUS

AGND

VCC

GND

*IFCLK/T0OUT

RESERVED

SCL

SDA

VCC

PB0/FD0

PB1/FD1

PB2/FD2

PB3/FD3

PD4/FD12 PD3/FD11 PD2/FD10

PD1/FD9 PD0/FD8

*WAKEUP

VCC

RESET#

GND

PA7/*FLAGD/SLCS #

PA6/PKTEND PA5/FIFOADR1 PA4/FIFOADR0

PA3/*WU2

PA2/*SLOE

PA1/INT1# PA0/INT0#

VCC

CTL2/*FLAGC

CTL1/*FLAGB CTL0/*FLAGA

GND

VCC

GND PB7/FD7 PB6/FD6 PB5/FD5 PB4/FD4

56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29

Figure 4-4. CY7C68013A/CY7C68014A 56-pin SSOP Pin Assignment

* denotes programm able polarity

Document #: 38-08032 Rev. *K Page 18 of 60

Page 19

A A

CLKOUT/**PE1/T1OUT

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

RDY0/*SLRD

RDY1/*SLWR

AVCC

XTALOUT

XTALIN

AGND

AVCC

DPLUS

DMINUS

AGND

VCC

GND

10 11 12

PD7/FD15

GND

VCC

1 2 3 4 5 6

GND

CY7C68013A/CY7C68014A

PD1/FD9

PD2/FD10

PD3/FD11

PD4/FD12

PD5/FD13

PD6/FD14

PD0/FD8

*WAKEUP

VCC

RESET#

GND

PA7/*FLAGD/SLCS#

PA6/*PKTEND

PA5/FIFOADR1

PA4/FIFOADR0

CY7C68015A/CY7C68016A

7 8 9

56-pin QFN

PA3/*WU2

PA2/*SLOE

PA1/INT1#

PA0/INT0#

VCC

CTL2/*FLAGC

*IFCLK/**PE0/T0OUT

RESERVED

13 14

SCL

Figure 4-5. CY7C68013A/14A/15A/16A 56-pin QFN Pin Assignment

VCC

SDA

** denotes CY7C68015A/ CY7C68016A pinout

PB1/FD1

PB0/FD0

* denotes programma ble polarity

PB2/FD2

PB3/FD3

PB4/FD4

PB5/FD5

PB6/FD6

PB7/FD7

GND

VCC

GND

30 29

CTL1/*FLAGB CTL0/*FLAGA

Document #: 38-08032 Rev. *K Page 19 of 60

Page 20

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

12345678

1A 2A 3A 4A 5A 6A 7A 8A

1B 2B 3B 4B 5B 6B 7B 8B

1C 2C 3C 4C 5C 6C 7C 8C

1D 2D 7D 8D

1E 2E 7E 8E

1F 2F 3F 4F 5F 6F 7F 8F

1G 2G 3G 4G 5G 6G 7G 8G

1H 2H 3H 4H 5H 6H 7H 8H

Figure 4-6. CY7C68013A 56-pin VFBGA Pin Assignment - Top view

Document #: 38-08032 Rev. *K Page 20 of 60

Page 21

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

4.1 CY7C68013A/15A Pin Descriptions

Table 4-1. FX2LP Pin Descriptions

128

TQFP

Note:

10. Unused inputs should not be left floating. Tie either HIGH or LOW as appropriate. Outputs should only be pulled up or down to ensure signals at power-up and

100

TQFP

10 9 10 3 2D AVCC Power N/A Analog VCC. Connect this pin to 3.3V power source.

17 16 14 7 1D AVCC Power N/ A Analog VCC. Connect thi s pin t o 3.3V power source.

13 12 13 6 2F AGND Ground N/A Anal og Ground. Connect to ground wi th as short a path

20 19 17 10 1F AGND Ground N/A Analog Ground. Connect to ground wi th as short a path

19 18 16 9 1E DMINUS I/O/Z Z USB D– Signal. Connect to the USB D– signal. 18 17 15 8 2E DPLUS I /O/Z Z USB D+ Signal. Connect to th e U S B D+ si gn al . 94 A0 Output L 8051 Address Bus. This bus is driven at all times. 95 A1 Output L 96 A2 Output L

97 A3 Output L 117 A4 Output L 118 A5 Output L 119 A6 Output L 120 A7 Output L 126 A8 Output L 127 A9 Output L 128 A10 Output L

21 A11 Output L

22 A12 Output L

23 A13 Output L

24 A14 Output L

25 A15 Output L

59 D0 I/O/Z Z 8051 Data Bus. This bidirectional bus is

60 D1 I/O/Z Z

61 D2 I/O/Z Z

62 D3 I/O/Z Z

63 D4 I/O/Z Z

86 D5 I/O/Z Z

87 D6 I/O/Z Z

88 D7 I/O/Z Z

39 PSEN# Output H Program Store Enable. This active-LOW signal

in standby. Note also that no pins should be driven while the device is powered down.

SSOP

QFN

VFBGA Name Type Default Description

[10]

This signal provi des power to the ana log sect ion of the chip.

as possible.

When the 8051 is addressi ng internal RAM it reflect s the internal address.

high-impedanc e when inactive, inpu t for bus reads, and output for bus write s. The dat a bus is used for exter nal 8051 program and dat a memory. The data bus is active only for external bus accesses, and i s driven LOW in suspend.

indicates an 8051 code fetch from external memory. It is active for progr am me mo ry fetches from 0x4000–0xFFFF when the EA pin is LOW, or from 0x0000–0xFFFF when the EA pin is HIGH.

Document #: 38-08032 Rev. *K Page 21 of 60

Page 22

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 4-1. FX2LP Pin Descriptions (continued)

128

TQFP

Port A

100

TQFP

34 28 BKPT Output L Breakpoint. This pin goes active (HIGH) when the 8051

99 77 49 42 8B RESET# Input N/A Activ e LOW Reset. Resets the en tire chip. See sectio n

35 EA Input N/A Ext ernal Access. This pi n deter mine s where t he 8051

12 11 12 5 1C XTALIN I nput N/A Crystal Input. Connect this signal to a 24-MHz

11 10 11 4 2C XTALOUT Output N/A Crystal Output. Connect this signal to a 24-MHz

1 100 5 54 2B CLKOUT on

82 67 40 33 8G PA0 or

83 68 41 34 6G PA1 or

SSOP

QFN

VFBGA Name Type Default Description

CY7C68013A

-----------------PE1 or T1OUT on CY7C68015A

INT0#

INT1#

[10]

O/Z

----------I/O/Z

I/O/Z I

12 MHz

---------I

(PE1)

(PA0)

(PA1)

address bus matches the BPADDRH/L registers and breakpoint s are enabled in the BREAKPT regi ster (BPEN = 1). If the BPPULSE bit in the BREAKPT register is HIGH, this signal pulses HIGH for eight 12-/24-/48-MHz c locks. I f the BPPULSE bit is LOW , the signal remains HIGH until the 8051 clears the BREAK bit (by writing 1 to it) in the BREAKPT register.

3.9 ”Reset and Wakeup”on page 6 for more details.

fetches code between addresses 0 x0000 and 0x3FFF. If EA = 0 the 8051 fetches this code from its internal RAM. IF EA = 1 the 8051 fetc hes this code from externa l memory.

parallel-resonant, fundamental mode crysta l and l oad capacitor to GND. It is also correct to drive XTALIN with an external 24-MHz square wave derived from another cloc k source. When drivi ng from an external source, the driving signal should be a 3.3V square wave.

parallel-resonant, fundamental mode crysta l and l oad capacitor to GND. If an external cloc k is used to drive XTALIN, leave this pin open.

CLKOUT: 12-, 24- or 48-MHz clock, phase locked t o the 24-MHz input cloc k. The 8051 defaults to 12- MHz operation. The 8051 may three-state this output by setting CPUCS.1 = 1.

-----------------------------------------------------------------------Multiplexe d pin whose function is selected by the PORTECFG.0 bit.

PE1 is a bidirectional I/O port pin. T1OUT is an active-HIGH signal from 8051

Timer-counter1. T1OUT outputs a high level for one CLKOUT clock cycl e when Ti mer1 overfl ows. I f T im er1 is operated in Mode 3 (two separate timer/counters), T1OUT is active when the low byte timer/counter overflows.

Multiplexed pin whose function is selected by PORTACFG.0

PA0 is a bidirectional IO port pin. INT0# is the active-LOW 8051 INT0 interrupt i nput

signal, which is either edge triggered (IT0 = 1) or level triggered (IT0 = 0).

Multiplexed pin whose function is selected by: PORTACFG.1

PA1 is a bidirectional IO port pin. INT1# is the active-LOW 8051 INT1 interrupt i nput

signal, which is either edge triggered (IT1 = 1) or level triggered (IT1 = 0).

Document #: 38-08032 Rev. *K Page 22 of 60

Page 23

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 4-1. FX2LP Pin Descriptions (continued)

128

TQFP

Port B

100

TQFP

84 69 42 35 8F PA2 or

85 70 43 36 7F PA3 or

89 71 44 37 6F PA4 or

90 72 45 38 8C PA5 or

91 73 46 39 7C PA6 or

92 74 47 40 6C PA7 or

44 34 25 18 3H PB0 or

45 35 26 19 4F PB1 or

46 36 27 20 4H PB2 or

47 37 28 21 4G PB3 or

SSOP

QFN

VFBGA Name Type Default Description

SLOE or

WU2

FIFOADR0

FIFOADR1

PKTEND

FLAGD or SLCS#

FD[0]

FD[1]

FD[2]

FD[3]

[10]

I/O/Z I

(PA2)

I/O/Z I

(PA3)

I/O/Z I

(PA4)

I/O/Z I

(PA5)

I/O/Z I

(PA6)

I/O/Z I

(PA7)

I/O/Z I

(PB0)

I/O/Z I

(PB1)

I/O/Z I

(PB2)

I/O/Z I

(PB3)

Multiplexe d pin whose function is selected by two bi ts: IFCONFIG[1:0].

PA2 is a bidirectional IO port pin. SLOE is an input-only output enable with program-

mable polari ty (F IFOPINPOLAR.4) for the sl ave F IFOs connected to FD[7. .0] or FD[15..0].

Multiplexed pin whose function is selected by: WAKEUP.7 and OEA.3

PA3 is a bidirectional I/O port pin. WU2 is an alternate source for USB W a k e up , enabled

by WU2EN bit (WAKEUP.1) and polarity set by WU2POL (WAKEUP.4). If the 8051 is in suspend and WU2EN = 1, a transition on this pin st arts up the oscil lator and interr upts the 8051 to allow it to exit the suspend mode. Asserti ng thi s pin i nhibi ts t he ch ip from suspending, i f WU2 EN = 1.

Multiplexed pin whose function is selected by: IFCONFIG[1..0].

PA4 is a bidirectional I/O port pin. FIFOADR0 is an input -only addr ess select for the slave

FIFOs connected to FD[ 7..0] or FD[15..0]. Multiplexed pin whose function is selected by:

IFCONFIG[1..0].

PA5 is a bidirectional I/O port pin. FIFOADR1 is an input -only addr ess select for the slave

FIFOs connected to FD[ 7..0] or FD[15..0]. Multiplexe d pin whose function is selected by the

IFCONFIG[1:0] bits.

PA6 is a bidirectional I/O port pin. PKTEND is an input used to commit the FIFO packet

data to the endpoint and whose polarity is programmable via FIFOPINPOLAR.5.

Multiplexe d pin whose function is selected by the IFCONFIG[1:0] and PORTACFG.7 bits.

PA7 is a bidirectional I/O port pin. FLAGD is a programmable slave-FIFO output status

flag signal . SLCS# gates all other slave FIFO enable/strobes

Multiplexe d pin whose function is selected by the follow in g bits: IFCONF IG [ 1 ..0 ] .

PB0 is a bidirection al I/O port pin. FD[0] is the bidirectional FIFO/GPIF data bus.

Multiplexe d pin whose function is selected by the follow in g bits: IFCONF IG [ 1 ..0 ] .

PB1 is a bidirection al I/O port pin. FD[1] is the bidirectional FIFO/GPIF data bus.

Multiplexe d pin whose function is selected by the follow in g bits: IFCONF IG [ 1 ..0 ] .

PB2 is a bidirectional I/O port pin. FD[2] is the bidirectional FIFO/GPIF data bus.

Multiplexe d pin whose function is selected by the follow in g bits: IFCONF IG [ 1 ..0 ] .

PB3 is a bidirectional I/O port pin. FD[3] is the bidirectional FIFO/GPIF data bus.

Document #: 38-08032 Rev. *K Page 23 of 60

Page 24

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 4-1. FX2LP Pin Descriptions (continued)

128

TQFP

PORT C

PORT D

100

TQFP

54 44 29 22 5H PB4 or

55 45 30 23 5G PB5 or

56 46 31 24 5F PB6 or

57 47 32 25 6H PB7 or

72 57 PC0 or

73 58 PC1 or

74 59 PC2 or

75 60 PC3 or

76 61 PC4 or

77 62 PC5 or

78 63 PC6 or

79 64 PC7 or

102 80 52 45 8A PD0 or

SSOP

QFN

VFBGA Name Type Default Description

FD[4]

FD[5]

FD[6]

FD[7]

GPIFADR0

GPIFADR1

GPIFADR2

GPIFADR3

GPIFADR4

GPIFADR5

GPIFADR6

GPIFADR7

FD[8]

[10]

I/O/Z I

(PB4)

I/O/Z I

(PB5)

I/O/Z I

(PB6)

I/O/Z I

(PB7)

I/O/Z I

(PC0)

I/O/Z I

(PC1)

I/O/Z I

(PC2)

I/O/Z I

(PC3)

I/O/Z I

(PC4)

I/O/Z I

(PC5)

I/O/Z I

(PC6)

I/O/Z I

(PC7)

I/O/Z I

(PD0)

Multiplexe d pin whose function is selected by the follow in g bits: IFCONF IG [ 1 ..0 ] .

PB4 is a bidirectional I/O port pin. FD[4] is the bidirectional FIFO/GPIF data bus.

Multiplexe d pin whose function is selected by the follow in g bits: IFCONF IG [ 1 ..0 ] .

PB5 is a bidirectional I/O port pin. FD[5] is the bidirectional FIFO/GPIF data bus.

Multiplexe d pin whose function is selected by the follow in g bits: IFCONF IG [ 1 ..0 ] .

PB6 is a bidirectional I/O port pin. FD[6] is the bidirectional FIFO/GPIF data bus.

Multiplexe d pin whose function is selected by the follow in g bits: IFCONF IG [ 1 ..0 ] .

PB7 is a bidirectional I/O port pin. FD[7] is the bidirectional FIFO/GPIF data bus.

Multiplexed pin whose function is selected by PORTCCFG.0

PC0 is a bidirectional I/O port pin. GPIFADR0 is a GPIF add ress output pin.

Multiplexed pin whose function is selected by PORTCCFG.1

PC1 is a bidirectional I/O port pin. GPIFADR1 is a GPIF address output pin.

Multiplexed pin whose function is selected by PORTCCFG.2

PC2 is a bidirectional I/O port pin. GPIFADR2 is a GPIF address output pin.

Multiplexed pin whose function is selected by PORTCCFG.3

PC3 is a bidirectional I/O port pin. GPIFADR3 is a GPIF address output pin.

Multiplexed pin whose function is selected by PORTCCFG.4

PC4 is a bidirectional I/O port pin. GPIFADR4 is a GPIF address output pin.

Multiplexed pin whose function is selected by PORTCCFG.5

PC5 is a bidirectional I/O port pin. GPIFADR5 is a GPIF address output pin.

Multiplexed pin whose function is selected by PORTCCFG.6

PC6 is a bidirectional I/O port pin. GPIFADR6 is a GPIF address output pin.

Multiplexed pin whose function is selected by PORTCCFG.7

PC7 is a bidirectional I/O port pin. GPIFADR7 is a GPIF address output pin.

Multiplexe d pin whose function is selected by the IFCONFIG[1..0] and EPxFI FO CFG.0 (wordwide) bits. FD[8] is the bidirectional FIFO/GPIF data bus.

Document #: 38-08032 Rev. *K Page 24 of 60

Page 25

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 4-1. FX2LP Pin Descriptions (continued)

128

TQFP

Port E

100

TQFP

103 81 53 46 7A PD1 or

104 82 54 47 6B PD2 or

105 83 55 48 6A PD3 or

121 95 56 49 3B PD4 or

122 96 1 50 3A PD5 or

123 97 2 51 3C PD6 or

124 98 3 52 2A PD7 or

108 86 PE0 or

109 87 PE1 or

110 88 PE2 or

111 89 P E3 or

SSOP

QFN

VFBGA Name Type Default Description

FD[9]

FD[10]

FD[11]

FD[12]

FD[13]

FD[14]

FD[15]

T0OUT

T1OUT

T2OUT

RXD0OUT

[10]

I/O/Z I

(PD1)

I/O/Z I

(PD2)

I/O/Z I

(PD3)

I/O/Z I

(PD4)

I/O/Z I

(PD5)

I/O/Z I

(PD6)

I/O/Z I

(PD7)

I/O/Z I

(PE0)

I/O/Z I

(PE1)

I/O/Z I

(PE2)

I/O/Z I

(PE3)

Multiplexe d pin whose function is selected by the IFCONFIG[1..0] and EPxFI FO CFG.0 (wordwide) bits. FD[9] is the bidirectional FIFO/GPIF data bus.

Multiplexe d pin whose function is selected by the IFCONFIG[1..0] and EPxFI FO CFG.0 (wordwide) bits. FD[10] is the bidirectional FIFO/GPIF data bus.

Multiplexe d pin whose function is selected by the IFCONFIG[1..0] and EPxFI FO CFG.0 (wordwide) bits. FD[11] is the bidirectional FIFO/GPIF data bus.

Multiplexe d pin whose function is selected by the IFCONFIG[1..0] and EPxFI FO CFG.0 (wordwide) bits. FD[12] is the bidirectional FIFO/GPIF data bus.

Multiplexe d pin whose function is selected by the IFCONFIG[1..0] and EPxFI FO CFG.0 (wordwide) bits. FD[13] is the bidirectional FIFO/GPIF data bus.

Multiplexe d pin whose function is selected by the IFCONFIG[1..0] and EPxFI FO CFG.0 (wordwide) bits. FD[14] is the bidirectional FIFO/GPIF data bus.

Multiplexe d pin whose function is selected by the IFCONFIG[1..0] and EPxFI FO CFG.0 (wordwide) bits. FD[15] is the bidirectional FIFO/GPIF data bus.

Multiplexe d pin whose function is selected by the PORTECFG.0 bit.

PE0 is a bidirectional I/O port pin. T0OUT is an active-HIGH signal from 8051

Timer-counter0. T0OUT outputs a high level for one CLKOUT clock cycl e when Ti mer0 overfl ows. I f T im er0 is operated in Mode 3 (two separate timer/counters), T0OUT is active when the low byte timer/counter overflows.

Multiplexe d pin whose function is selected by the PORTECFG.1 bit.

PE1 is a bidirectional I/O port pin. T1OUT is an active-HIGH signal from 8051

Multiplexe d pin whose function is selected by the PORTECFG.2 bit.

PE2 is a bidirectional I/O port pin. T2OUT is the active-HIGH out put signal from 8051

Timer2. T2OUT is acti ve (H I G H ) fo r one clock cycl e when Timer/Counter 2 overflows.

Multiplexe d pin whose function is selected by the PORTECFG.3 bit.

PE3 is a bidirectional I/O port pin. RXD0OUT is an active- HIGH signal from 8051 UAR T0.

If RXD0OUT is selected and UART0 is in Mode 0, thi s pin provides the output data for UART0 only when it is in sync mode. Otherwise it is a 1.

Document #: 38-08032 Rev. *K Page 25 of 60

Page 26

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 4-1. FX2LP Pin Descriptions (continued)

128

TQFP

100

TQFP

112 90 PE4 or

113 91 PE5 or

114 92 PE6 or

115 93 PE7 or

43811ARDY0 or

54921BRDY1 or

6 5 RDY2 Input N/A RDY2 is a GPIF input signal. 7 6 RDY3 Input N/A RDY3 is a GPIF input signal. 8 7 RDY4 Input N/A RDY4 is a GPIF input signal. 9 8 RDY5 Input N/A RDY5 is a GPIF input signal.

69 54 36 29 7H CTL0 or

SSOP

QFN

VFBGA Name Type Default Description

RXD1OUT

INT6

T2EX

GPIFADR8

SLRD

SLWR

FLAGA

[10]

I/O/Z I

(PE4)

I/O/Z I

(PE5)

I/O/Z I

(PE6)

I/O/Z I

(PE7)

Input N/A Multi plexed pin whose functi on is selected by the

O/Z H Multiplexed pin whose functi on is selected by the

Multiplexe d pin whose function is selected by the PORTECFG.4 bit.

PE4 is a bidirectional I/O port pin. RXD1OUT is an active-HI GH output from 8051 UAR T1.

When RXD1OUT is selected and UART1 is in Mode 0, this pin provides the output data for UART1 only when it is in sync mo de. In Modes 1, 2, and 3, this pi n is HIGH.

Multiplexe d pin whose function is selected by the PORTECFG.5 bit.

PE5 is a bidirectional I/O port pin. INT6 is the 8051 INT6 interrupt reques t input signal. The

INT6 pin is edge-sensitive, active HIGH. Multiplexe d pin whose function is selected by the

PORTECFG.6 bit.

PE6 is a bidirectional I/O port pin. T2EX is an acti ve-HIGH input signal to t he 8051 T imer2.

T2EX reloads timer 2 on its falling edge. T2EX is acti ve only if the EXEN2 bit is set in T2CON.

Multiplexe d pin whose function is selected by the PORTECFG.7 bit.

PE7 is a bidirectional I/O port pin. GPIFADR8 is a GPIF address output pin.

follow in g bits : IFCONFIG[1..0].

RDY0 is a GPIF input signal. SLRD is the input-o nly rea d strob e with pr ogram mable

polarity (FIFOPINPOLAR.3) for the slave FIFOs connected to FD[7. .0] or FD[15..0].

follow in g bits : IFCONFIG[1..0].

RDY1 is a GPIF input signal. SLWR is the input -only write strobe with programmable

polarity (FIFOPINPOLAR.2) for the slave FIFOs connected to FD[7. .0] or FD[15..0].

follow in g bits : IFCONFIG[1..0].

CTL0 is a GPIF control output. FLAGA is a programmable slave-FIFO output status

flag signal . Defaults to pr ogr ammable fo r the FI FO sel ected by the FIFOADR[1:0] pins.

Document #: 38-08032 Rev. *K Page 26 of 60

Page 27

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 4-1. FX2LP Pin Descriptions (continued)

128

TQFP

100

TQFP

70 55 37 30 7G CTL1 or

71 56 38 31 8H CTL2 or

66 51 CTL3 O/Z H CTL3 is a GPIF contro l output. 67 52 CTL4 Output H CTL4 is a GPIF contro l out put. 98 76 CTL5 Output H CTL5 is a GPIF contro l out put. 32 26 20 13 2G IFCLK on

28 22 INT4 Input N/A INT4 is the 8051 INT4 interrupt reques t input signal. The

106 84 INT5# I nput N/A INT5# is the 8051 INT5 interrupt request input signal.

31 25 T2 Input N/A T2 is the active-HIGH T2 input signal to 8051 Timer2,

30 24 T1 Input N/A T1 is the active-HI GH T1 si gnal f or 8051 Timer1, which

29 23 T0 Input N/A T0 is the active-HI GH T0 si gnal f or 8051 Timer0, which

53 43 RXD1 Input N/A RXD1is an active-HIGH input signal for 8051 UART1,

52 42 TXD1 Output H TXD1is an active-HIGH output pin from 8051 UART1,

SSOP

QFN

VFBGA Name Type Default Description

FLAGB

FLAGC

CY7C68013A

-----------------PE0 or T0OUT on CY7C68015A

[10]

O/Z H Multiplexed pin whose functi on is selected by the

I/O/Z

----------I/O/Z

---------(PE0)

follow in g bits : IFCONFIG[1..0].

CTL1 is a GPIF control output. FLAGB is a programmable slave-FIFO output status

flag signal . Defaults to FULL for the FIFO selected by the FIFOADR[1:0] pins.

follow in g bits : IFCONFIG[1..0].

CTL2 is a GPIF control output. FLAGC is a programmable slave-FIFO output status

flag signal . Defaults to EMPTY for the FIFO selected by the FIFOADR[1:0] pins.

Interface Clock, used for synchr onously clocking data into or out of the slave FIFOs. IFCLK also serves as a timing reference for all slave FIFO control signals and GPIF. When internal clocki ng is used (IF CONFIG.7 = 1) the IFCLK pin can be configured to output 30/48 MHz by bits IFCONFIG.5 and IFCONFIG.6. IFCLK may be inverted, whether internally or externally source d, by setting the bit IFCO NFIG.4 =1.

----------------------------------------------------------------------Multiplexe d pin whose function is selected by the

PORTECFG.0 bit.

PE0 is a bidirectional I/O port pin. T0OUT is an active-HIGH signal from 8051

INT4 pin is edge-sensitive, active HIGH.

The INT5 pin is edge-se nsitive, active LOW.

which provides the in put t o Timer2 when C/T2 = 1. When C/T2 = 0, Timer2 does not use this pin.

provides t he input to T imer1 when C/T1 is 1. When C/T1 is 0, Timer1 does not use this bit.

provides t he input to T imer0 when C/T0 is 1. When C/T0 is 0, Timer0 does not use this bit.

which provides data to the UART in all modes.

which provides the output cl ock in sync mode, and the output data i n async mode.

Document #: 38-08032 Rev. *K Page 27 of 60

Page 28

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 4-1. FX2LP Pin Descriptions (continued)

128

TQFP

100

TQFP

51 41 RXD0 Input N/A RXD0 is the active-HIGH RXD0 input to 8051 UAR T0,

50 40 TXD0 Output H TXD0 is the active-HIGH TXD0 output from 8051

42 CS# Output H CS# is the active -LOW ch ip select for ext ernal mem ory . 41 32 WR# Output H WR# is the active- LOW wri te str obe o utput f or ext ernal

40 31 RD# Output H RD# is the active-LOW read strobe output for external

38 OE# Output H OE# is the active-LOW output enable for external

33 27 21 14 2H Reserved Input N/A Reserved. Connect to ground.

101 79 51 44 7B WAKEUP Input N/A USB Wakeup. If the 8051 is in suspend, asserting this

36 29 22 15 3F SCL OD Z Clock for the I

37 30 23 16 3G SDA OD Z Data for I

SSOP

QFN

VFBGA Name Type Default Description

[10]

which provides data to the UART in all modes.

UART0, which pr ovides t he o utput cl ock i n sync m ode, and the output dat a in async mode.

memory.

pin starts up the oscillator and interrupts the 8051 to allow it to exit the suspend mode. Holding WAKEUP asserted inhibits the EZ-USB This pin has programmab le polarity (W AKEUP.4).

C interface. Connect to VCC with a 2. 2K

resistor, even if no I

C-compatible interface. Connect to VCC with a 2.2K resistor, even if no I peripheral is attached.

C peripheral is attached.



chip from suspendi ng.

C-compatible

2 1 6 55 5A VCC Power N/A VCC. Conne c t to 3.3 V pow e r so ur c e. 26 20 18 11 1G VCC Power N/A VCC. Conne c t to 3.3V po w e r so ur c e. 43 33 24 17 7E VCC Power N/A VCC. Conne c t to 3.3 V po w e r so ur c e. 48 38 VCC Power N/A VCC. Co nn e c t to 3.3V po we r source. 64 49 34 27 8E VCC Power N/A VCC. Conne c t to 3.3 V po w e r so ur c e. 68 53 VCC Power N/A VCC. Co nn e c t to 3.3V po we r source. 81 66 39 32 5C VCC Power N/A VCC. Conne c t to 3.3V po w e r so ur c e.

100 78 50 43 5B VCC Power N/ A VCC. C o nn e c t to 3.3V po w e r so ur c e. 107 85 VCC Power N/A VCC. Conne ct to 3.3V pow e r so ur c e.

3 2 7 56 4B GND Ground N/A Ground. 27 21 19 12 1H GND Ground N/A Ground. 49 39 GND Ground N/A Ground. 58 48 33 26 7D GND Ground N/A Ground. 65 50 35 28 8D GND Ground N/A Ground. 80 65 GND Ground N/A Ground. 93 75 48 41 4C GND Ground N/A Ground.

116 94 GND Ground N/A Ground. 125 99 4 53 4A GND Ground N/A Ground.

14 13 NC N/A N/A No Connect. This pin must be left open. 15 14 NC N/A N/A No Connect. This pin must be left open. 16 15 NC N/A N/A No Connect. This pin must be left open.

Document #: 38-08032 Rev. *K Page 28 of 60

Page 29

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

5.0 Register Summary

FX2LP register bit def initions are described in the FX2LP TRM in greater detail.

Table 5-1. FX2LP Register Summary

Hex Size Name Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access

E400 128 WAVEDATA GPIF Waveform

E480 128 reserved

E50D GPCR2 General Purpos e Confi gu-

E600 1 CPUCS CPU Control & Status 0 0 PORTCSTB CLKSPD1 CLKSPD0 CLKINV CLKOE 8051RES 00000010 rrbbbbbr E601 1 IFCONFIG Interface Configuration

E602 1 PINFLAGSAB

E603 1 PINFLAGSCD

E604 1 FIFORESET

E605 1 BREAKPT Breakpoint Control 0 0 0 0 BREAK BPPULSE BPEN 0 00000000 rrrrbbbr E606 1 BPADDRH Breakpoint Address H A15 A14 A13 A12 A11 A10 A9 A8 xxxxxxxx RW E607 1 BPADDRL Breakpoint Address L A7 A6 A5 A4 A3 A2 A1 A0 xxxxxxxx RW E608 1 UART230 230 Kbaud internally

E609 1 FIFOPINPOLAR

E60A 1 REVID Chip Revision rv7 rv6 rv5 rv4 rv3 rv2 rv1 rv0 RevA

E60B 1 REVCTL

E60C 1 GPIFHOLDAMOUNT MSTB Hold Time

E610 1 EP1OUTCFG Endpoint 1-OUT

E611 1 EP1INCFG Endpoint 1-IN

E612 1 EP2CFG Endpoint 2 Configuration VALID DIR TYPE1 TYPE0 SIZE 0 BUF1 BUF0 10100010 bbbbbrbb E613 1 EP4CFG Endpoint 4 Configuration VALID DIR TYPE1 TYPE0 0 0 0 0 10100000 bbbbrrrr E614 1 EP6CFG Endpoint 6 Configuration VALID DIR TYPE1 TYPE0 SIZE 0 BUF1 BUF0 11100010 bbbbbrbb E615 1 EP8CFG Endpoint 8 Configuration VALID DIR TYPE1 TYPE0 0 0 0 0 11100000 bbbbrrrr

E618 1 EP2FIFOCFG

E619 1 EP4FIFOCFG

E61A 1 EP6FIFOCFG

E61B 1 EP8FIFOCFG

E61C 4 reserved E620 1 EP2AUTOINLENH

E621 1 EP2AUTOINLENL

E622 1 EP4AUTOINLENH

E623 1 EP4AUTOINLENL

E624 1 EP6AUTOINLENH

E625 1 EP6AUTOINLENL

E626 1 EP8AUTOINLENH

E627 1 EP8AUTOINLENL

E628 1 ECCCFG ECC Configuration 0 0 0 0 0 0 0 ECCM 00000000 rrrrrrrb E629 1 ECCRESET ECC Reset x x x x x x x x 00000000 W E62A 1 ECC1B0 ECC1 Byte 0 Address LINE15 LINE14 LINE13 LINE12 LINE11 LINE10 LINE9 LINE8 00000000 R E62B 1 ECC1B1 ECC1 Byte 1 Address LINE7 LINE6 LINE5 LINE4 LINE3 LINE2 LINE1 LINE0 00000000 R E62C 1 ECC1B2 ECC1 Byte 2 Address COL5 COL4 COL3 COL2 COL1 COL0 LINE17 LINE16 00000000 R E62D 1 ECC2B0 ECC2 Byte 0 Address LINE15 LINE14 LINE13 LINE12 LINE11 LINE10 LINE9 LINE8 00000000 R

Note:

11. Read and writes to these registers may require synchronization delay, see Technical Reference Manual for “Synchronization Delay.”

GPIF Waveform Memories

GENERAL CONFIGURATION

UDMA

3 reserved

ENDPOINT CONFIGURATION

2 reserved

[11]

Descriptor 0, 1, 2, 3 data

ration Register 2

(Ports, GPIF, slave F IFOs) Slave FIFO FLAGA and

FLAGB Pin Configuration

Slave FIFO FLAGC and

FLAGD Pin Configuration Restore FIFOS to default

state

generated ref. clock Slave FIFO Interface pins

polarity

Chip Revision Control 0 0 0 0 0 0 dyn_out enh_pkt 00000000 rrrrrrbb

(for UDMA)

Configuration

Endpoint 2 / slave FIFO configuration

Endpoint 4 / slave FIFO configuration

Endpoint 6 / slave FIFO configuration

Endpoint 8 / slave FIFO configuration

[11

Endpoint 2 AUTOIN

Packet Length H

[11]

Endpoint 2 AUTOIN Packet Length L

[11]

Endpoint 4 AUTOIN Packet Length H

[11]

Endpoint 4 AUTOIN Packet Length L

[11]

Endpoint 6 AUTOIN Packet Length H

[11]

Endpoint 6 AUTOIN Packet Length L

[11]

Endpoint 8 AUTOIN Packet Length H

[11]

Endpoint 8 AUTOIN Packet Length L

D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW

reserved reserved reserved FULL_SPEE

IFCLKSRC 3048MHZ IFCLKOE IFCLKPOL ASYNC GSTATE IFCFG1 IFCFG0 10000000 RW

FLAGB3 FLAGB2 FLAGB1 FLAGB0 FLAGA3 FLAGA2 FLAGA1 FLAGA0 00000000 RW

FLAGD3 FLAGD2 FLAGD1 FLAGD0 FLAGC3 FLAGC2 FLAGC1 FLAGC0 00000000 RW

NAKALL 0 0 0 EP3 EP2 EP1 EP0 xxxxxxxx W

0 0 0 0 0 0 230UART1 230UART0 00000000rrrrrrbb

0 0 PKTEND SLOE SLRD SLWR EF FF 00000000rrbbbbbb

0 0 0 0 0 0 HOLDTIME1 HOLDTIME0 00000000rrrrrrbb

VALID 0 TYPE1 TYPE0 0 0 0 0 10100000 brbbrrrr

0 INFM1 OEP1 AUTOOUT AUTOIN ZEROLENIN 0 WORDWIDE 00000101rbbbbbrb

0 0 0 0 0 PL10 PL9 PL8 00000010rrrrrbbb

PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 RW

0 0 0 0 0 0 PL9 PL8 00000010rrrrrrbb

PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 RW

0 0 0 0 0 PL10 PL9 PL8 00000010rrrrrbbb

PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 RW

0 0 0 0 0 0 PL9 PL8 00000010rrrrrrbb

PL7 PL6 PL5 PL4 PL3 PL2 PL1 PL0 00000000 RW

D_ONLY

reserved reserved reserved reserved 00000000R

00000001

Document #: 38-08032 Rev. *K Page 29 of 60

Page 30

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 5-1. FX2LP Register Summary (continued)

Hex Size Name Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access E62E 1 ECC2B1 ECC2 Byte 1 Address LINE7 LINE6 LINE5 LINE4 LINE3 LINE2 LINE1 LINE0 00000000 R E62F 1 ECC2B2 ECC2 Byte 2 Address COL5 COL4 COL3 COL2 COL1 COL0 0 0 00000000 R E630

1 EP2FIFOPFH

H.S. E630

F.S. E631

H.S. E631

F.S E632

H.S. E632

F.S E633

H.S. E633

F.S E634

H.S. E634

F.S E635

H.S. E635

F.S E636

H.S. E636

F.S E637

H.S. E637

F.S

E640 1 EP2ISOINPKTS EP2 (if ISO) IN Packets

E641 1 EP4ISOINPKTS EP4 (if ISO) IN Packets

E642 1 EP6ISOINPKTS EP6 (if ISO) IN Packets

E643 1 EP8ISOINPKTS EP8 (if ISO) IN Packets

E644 4 reserved E648 1 INPKTEND E649 7 OUTPKTEND

E650 1 EP2FIFOIE

E651 1 EP2FIFOIRQ

E652 1 EP4FIFOIE

E653 1 EP4FIFOIRQ

E654 1 EP6FIFOIE

E655 1 EP6FIFOIRQ

E656 1 EP8FIFOIE

E657 1 EP8FIFOIRQ

E658 1 IBNIE IN-BULK-NAK Interrupt

E659 1 IBNIRQ

E65A 1 NAKIE Endpoint Ping-NAK / IBN

E65B 1 NAKIRQ

E65C 1 USBIE USB Int Enables 0 EP0ACK HSGRANT URES SUSP SUTOK SOF SUDAV 00000000 RW E65D 1 USBIRQ E65E 1 EPIE Endpoint Interrupt

E65F 1 EPIRQ

E660 1 GPIFIE E661 1 GPIFIRQ

1 EP2FIFOPFH

1 EP2FIFOPFL

1 EP4FIFOPFH

1 EP4FIFOPFL

1 EP6FIFOPFH

1 EP6FIFOPFL

1 EP8FIFOPFH

1 EP8FIFOPFL

8 reserved

INTERRUPTS

Note:

12. The register can only be reset, it cannot be set.

[11]

Endpoint 2 / slave FIFO Programmable Flag H

[11]

Endpoint 2 / slave FIFO Programmable Flag H

[11]

Endpoint 2 / slave FIFO Programmable Flag L

[11]

Endpoint 2 / slave FIFO Programmable Flag L

[11]

Endpoint 4 / slave FIFO Programmable Flag H

[11]

Endpoint 4 / slave FIFO Programmable Flag H

[11]

Endpoint 4 / slave FIFO Programmable Flag L

[11]

Endpoint 4 / slave FIFO Programmable Flag L

[11]

Endpoint 6 / slave FIFO Programmable Flag H

[11]

Endpoint 6 / slave FIFO Programmable Flag H

[11]

Endpoint 6 / slave FIFO Programmable Flag L

[11]

Endpoint 6 / slave FIFO Programmable Flag L

[11]

Endpoint 8 / slave FIFO Programmable Flag H

[11]

Endpoint 8 / slave FIFO Programmable Flag H

[11]

Endpoint 8 / slave FIFO Programmable Flag L

[11]

Endpoint 8 / slave FIFO Programmable Flag L

per frame (1-3)

[11]

Force IN Packet End Skip 0 0 0 EP3 EP2 EP1 EP0 xxxxxxxx W

[11]

Force OUT Packet End Skip 0 0 0 EP3 EP2 EP1 EP0 xxxxxxxx W

[11]

Endpoint 2 slave FIFO Flag Interrupt Enable

[11,12]

Endpoint 2 slave FIFO Flag Interrupt Request

[11]

Endpoint 4 slave FIFO Flag Interrupt Enable

[11,12]

Endpoint 4 slave FIFO Flag Interrupt Request

[11]

Endpoint 6 slave FIFO Flag Interrupt Enable

[11,12]

Endpoint 6 slave FIFO Flag Interrupt Request

[11]

Endpoint 8 slave FIFO Flag Interrupt Enable

[11,12]

Endpoint 8 slave FIFO Flag Interrupt Request

[12]

[11]

GPIF Interrupt Enable 0 0 0 0 0 0 GPIFWF GPIFDONE 00000000 RW

[11]

Enable IN-BULK-NAK interrupt

Request

Interrupt Enable Endpoint Ping-NAK / IBN

Interrupt Request

USB Interrupt Requests 0 EP0ACK HSGRANT URES SUSP SUTOK SOF SUDAV 0xxxxxxx rbbbbbbb

Enables Endpoint Interrupt

Requests

GPIF Interrupt Request 0 0 0 0 0 0 GPIFWF GPIFDONE 000000xx RW

DECIS PKTSTAT IN:PKTS[2]

DECIS PKTSTAT OUT:PFC12 OUT:PFC11 OUT:PFC10 0 PFC9 IN:PKTS[2]

PFC7 PFC6 PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW

IN:PKTS[1] OUT:PFC7

DECIS PKTSTAT 0 IN: PKTS[1]

DECIS PKTSTAT 0 OUT:PFC10 OUT:PFC9 0 0 PFC8 10001000bbrbbrrb

PFC7 PFC6 PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW

IN: PKTS[1] OUT:PFC7

DECIS PKTSTAT IN:PKTS[2]

DECIS PKTSTAT OUT:PFC12 OUT:PFC11 OUT:PFC10 0 PFC9 IN:PKTS[2]

PFC7 PFC6 PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW

IN:PKTS[1] OUT:PFC7

DECIS PKTSTAT 0 IN: PKTS[1]

DECIS PKTSTAT 0 OUT:PFC10 OUT:PFC9 0 0 PFC8 00001000bbrbbrrb

PFC7 PFC6 PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 00000000 RW

IN: PKTS[1] OUT:PFC7

AADJ 0 0 0 0 0 INPPF1 INPPF0 00000001brrrrrbb

AADJ 0 0 0 0 0 INPPF1 INPPF0 00000001brrrrrrr

AADJ 0 0 0 0 0 INPPF1 INPPF0 00000001brrrrrbb

AADJ 0 0 0 0 0 INPPF1 INPPF0 00000001brrrrrrr

0 0 0 0 EDGEPF PF EF FF 00000000 RW

0 0 0 0 0 PF EF FF 00000000rrrrrbbb

0 0 0 0 EDGEPF PF EF FF 00000000 RW

0 0 0 0 0 PF EF FF 00000000rrrrrbbb

0 0 0 0 EDGEPF PF EF FF 00000000 RW

0 0 0 0 0 PF EF FF 00000000rrrrrbbb

0 0 0 0 EDGEPF PF EF FF 00000000 RW

0 0 0 0 0 PF EF FF 00000000rrrrrbbb

0 0 EP8 EP6 EP4 EP2 EP1 EP0 00000000RW

0 0 EP8 EP6 EP4 EP2 EP1 EP0 00xxxxxx rrbbbbbb

EP8 EP6 EP4 EP2 EP1 EP0 0 IBN 00000000 RW

EP8 EP6 EP4 EP2 EP1 EP0 0 IBN xxxxxx0x bbbbbbrb

EP8 EP6 EP4 EP2 EP1OUT EP1IN EP0OUT EP0IN 00000000 RW

EP8 EP6 EP4 EP2 EP1OUT EP1IN EP0OUT EP0IN 0 RW

IN:PKTS[0] OUT:PFC6

IN: PKTS[0] OUT:PFC6

IN:PKTS[0] OUT:PFC6

IN: PKTS[0] OUT:PFC6

OUT:PFC12

PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 00000000RW

OUT:PFC12

PFC5 PFC4 PFC3 PFC2 PFC1 PFC0 00000000RW

IN:PKTS[1] OUT:PFC11

OUT:PFC10

IN:PKTS[1] OUT:PFC11

OUT:PFC10

IN:PKTS[0] OUT:PFC10

IN: PKTS[0] OUT:PFC9

IN:PKTS[0] OUT:PFC10

IN: PKTS[0] OUT:PFC9

0 PFC9 PFC8 10001000 bbbbbrbb

OUT:PFC8

0 0 PFC8 10001000bbrbbrrb

0 PFC9 PFC8 00001000 bbbbbrbb

OUT:PFC8

0 0 PFC8 00001000bbrbbrrb

10001000bbbbbrbb

00001000bbbbbrbb

Document #: 38-08032 Rev. *K Page 30 of 60

Page 31

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 5-1. FX2LP Register Summary (continued)

Hex Size Name Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access E662 1 USBERRIE USB Error Interrupt

E663 1 USBERRIRQ

E664 1 ERRCNTLIM USB Error counter and

E665 1 CLRERRCNT Clear Error Counter EC3:0x x x x x x x x xxxxxxxx W E666 1 INT2IVEC Interrupt 2 (USB)

E667 1 INT4IVEC Interrupt 4 (slave FIFO &

E668 1 INTSET-UP Interrupt 2&4 set-up 0 0 0 0 AV2EN 0 INT4SRC AV4EN 00000000RW E669 7 reserved

E670 1 PORTACFG I/O PORTA Alternate

E671 1 PORTCCFG I/O PORTC Alternate

E672 1 PORTECFG I/O PORTE Alternate

E673 4 reserved E677 1 reserved E678 1 I2CS I²C Bus

E679 1 I2DAT I²C Bus

E67A 1 I2CTL I²C Bus

E67B 1 XAUTODAT1 Autoptr1 MOVX access,

E67C 1 XAUTODAT2 Autoptr2 MOVX access,

E67D 1 UDMACRCH E67E 1 UDMACRCL E67F 1 UDMACRC-

E680 1 USBCS USB Control & Status HSM 0 0 0 DISCON NOSYNSOF RENUM SIGRSUME x0000000 rrrrbbbb E681 1 SUSPEND Put chip into suspend x x x x x x x x xxxxxxxx W E682 1 WAKEUPCS Wakeup Control & Status WU2 WU WU2POL WUPOL 0 DPEN WU2EN WUEN xx000101 bbbbrbbb E683 1 TOGCTL Toggle Control Q S R IO EP3 EP2 EP1 EP0 x0000000 rrrbbbbb E684 1 USBFRAMEH US B Frame count H 0 0 0 0 0 FC10 FC9 FC8 00000xxx R E685 1 USBFRAMEL USB Frame count L FC7 FC6 FC5 FC4 FC3 FC2 FC1 FC0 xxxxxxxx R E686 1 MICROFRAME Microframe count, 0-7 0 0 0 0 0 MF2 MF1 MF0 00000xxx R E687 1 FNADDR USB Function address 0 FA6 FA5 FA4 FA3 FA2 FA1 FA0 0xxxxxxx R E688 2 reserved

E68A 1 EP0BCH E68B 1 EP0BCL E68C 1 reserved E68D 1 EP1OUTBC Endpoint 1 OUT Byte

E68E 1 reserved E68F 1 EP1INBC Endpoint 1 IN Byte Count 0 BC6 BC5 BC4 BC3 BC2 BC1 BC0 0xxxxxxx RW E690 1 EP2BCH E691 1 EP2BCL E692 2 reserved E694 1 EP4BCH E695 1 EP4BCL E696 2 reserved E698 1 EP6BCH E699 1 EP6BCL E69A 2 reserved E69C 1 EP8BCH E69D 1 EP8BCL E69E 2 reserved E6A0 1 EP0CS Endpoint 0 Control and

E6A1 1 EP1OUTCS Endpoint 1 OUT Control

E6A2 1 EP1INCS Endpoint 1 IN Control and

E6A3 1 EP2CS Endpoint 2 Control and

INPUT / OUTPUT

UDMA CRC

QUALIFIER USB CONTROL

ENDPOINTS

[11]

Enables

[12]

USB Error Interrupt Requests

limit

Autovector

GPIF) Autovector

Configuration

Control & Status

Data

Control

when APTREN=1

[11]

UDMA CRC MSB CRC15 CRC14 CRC13 CRC12 CRC11 CRC10 CRC9 CRC8 01001010 RW

[11]

UDMA CRC LSB CRC7 CRC6 CRC5 CRC4 CRC3 CRC2 CRC1 CRC0 10111010 RW UDMA CRC Qualifier QENABLE 0 0 0 QSTATE QSIGNAL2 QSIGNAL1 QSIGNAL0 00000000 brrrbbbb

Endpoint 0 Byte Count H (BC15) (BC14) (BC13) (BC12) (BC11) (BC10) (BC9) (BC8) xxxxxxxx RW Endpoint 0 Byte Count L (BC7) BC6 BC5 BC4 BC3 BC2 BC1 BC0 xxxxxxxx RW

Count

Endpoint 2 Byte Count H 0 0 0 0 0 BC10 BC9 BC8 00000xxx RW

Endpoint 2 Byte Count L BC7/SKIP BC6 BC5 BC4 BC3 BC2 BC1 BC0 xxxxxxxx RW

Endpoint 4 Byte Count H 0 0 0 0 0 0 BC9 BC8 000000xx RW

Endpoint 4 Byte Count L BC7/SKIP BC6 BC5 BC4 BC3 BC2 BC1 BC0 xxxxxxxx RW

Endpoint 6 Byte Count H 0 0 0 0 0 BC10 BC9 BC8 00000xxx RW

Endpoint 6 Byte Count L BC7/SKIP BC6 BC5 BC4 BC3 BC2 BC1 BC0 xxxxxxxx RW

Endpoint 8 Byte Count H 0 0 0 0 0 0 BC9 BC8 000000xx RW Endpoint 8 Byte Count L BC7/SKIP BC6 BC5 BC4 BC3 BC2 BC1 BC0 xxxxxxxx RW

Status

and Status

Status

ISOEP8 ISOEP6 ISOEP4 ISOEP2 0 0 0 ERRLIMIT 00000000RW

ISOEP8 ISOEP6 ISOEP4 ISOEP2 0 0 0 ERRLIMIT 0000000x bbbbrrrb

EC3 EC2 EC1 EC0 LIMIT3 LIMIT2 LIMIT1 LIMIT0 xxxx0100 rrrrbbbb

0 I2V4 I2V3 I2V2 I2V1 I2V0 0 0 00000000 R

1 0 I4V3 I4V2 I4V1 I4V0 0 0 10000000 R

FLAGD SLCS 0 0 0 0 INT1 INT0 00000000 RW

GPIFA7 GPIFA6 GPIFA5 GPIFA4 GPIFA3 GPIFA2 GPIFA1 GPIFA0 00000000RW

GPIFA8 T2EX INT6 RXD1OUT RXD0OUT T2OUT T1OUT T0OUT 00000000 RW

START STOP LASTRD ID1 ID0 BERR ACK DONE 000xx000 bbbrrrrr

d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx RW

0 0 0 0 0 0 STOPIE 400KHZ 00000000 RW

D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW

0 BC6 BC5 BC4 BC3 BC2 BC1 BC0 0xxxxxxx RW

HSNAK 0 0 0 0 0 BUSY STALL 10000000 bbbbbbrb

0 0 0 0 0 0 BUSY STALL 00000000bbbbbbrb

0 NPAK2 NPAK1 NPAK0 FULL EMPTY 0 STALL 00101000 rrrrrrrb

Document #: 38-08032 Rev. *K Page 31 of 60

Page 32

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 5-1. FX2LP Register Summary (continued)

Hex Size Name Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access E6A4 1 EP4CS Endpoint 4 Control and

E6A5 1 EP6CS Endpoint 6 Control and

E6A6 1 EP8CS Endpoint 8 Control and

E6A7 1 EP2FIFOFLGS Endpoint 2 slave FIFO

E6A8 1 EP4FIFOFLGS Endpoint 4 slave FIFO

E6A9 1 EP6FIFOFLGS Endpoint 6 slave FIFO

E6AA 1 EP8FIFOFLGS Endpoint 8 slave FIFO

E6AB 1 EP2FIFOBCH Endpoint 2 slave FIFO

E6AC 1 EP2FIFOBCL Endpoint 2 slave FIFO

E6AD 1 EP4FIFOBCH Endpoint 4 slave FIFO

E6AE 1 EP4FIFOBCL Endpoint 4 slave FIFO

E6AF 1 EP6FIFOBCH Endpoint 6 slave FIFO

E6B0 1 EP6FIFOBCL Endpoint 6 slave FIFO

E6B1 1 EP8FIFOBCH Endpoint 8 slave FIFO

E6B2 1 EP8FIFOBCL Endpoint 8 slave FIFO

E6B3 1 SUDPTRH Set-up Data Pointer high

E6B4 1 SUDPTRL Set-up Data Pointer low

E6B5 1 SUDPTRCTL Set-up Data Pointer Auto

2 reserved

E6B8 8 SET-UPDAT 8 bytes of set-up data D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx R

GPIF E6C0 1 GPIFWFSELECT Waveform Selector SINGLEWR1 SINGLEWR0SINGLERD1 SINGLERD0 FIFOWR1 FIFOWR0 FIFORD1 FIFORD0 11100100 RW E6C1 1 GPIFIDLECS GPIF Done, GPIF IDLE

E6C2 1 GPIFIDLECTL Inactive Bus, CTL states 0 0 CTL5 CTL4 CTL3 CTL2 CTL1 CTL0 11111111 RW E6C3 1 GPIFCTLCFG CT L Drive Type TRICTL 0 CTL5 CTL4 CTL3 CTL2 CTL1 CTL0 00000000RW E6C4 1 GPIFADRH E6C5 1 GPIFADRL

FLOWSTATE E6C6 1 FLOWSTATE Flowstate Enable and

E6C7 1 FLOWLOGIC Flowstate Logic LFUNC1 LFUNC0 TERMA2 TERMA1 TERMA0 TERMB2 TERMB1 TERMB0 00000000 RW E6C8 1 FLOWEQ0CTL CTL-Pin States in

E6C9 1 FLOWEQ1CTL CTL-Pin States in Flow-

E6CA 1 FLOWHOLDOFF Holdoff Configuration HOPERIOD3 HOPERIOD2 HOPERIOD1 HOPERIOD0HOSTATE HOCTL2 HOCTL1 HOCTL0 00010010RW

E6CB 1 FLOWSTB Flowstate Strobe

E6CC 1 FLOWSTBEDGE Flowstate Rising/Falling

E6CD 1 FLOWSTBPERIOD Master-Strobe Half-PeriodD7 D6 D5 D4 D3 D2 D1 D0 00000010RW E6CE 1 GPIFTCB3

E6CF 1 GPIFTCB2

E6D0 1 GPIFTCB1

E6D1 1 GPIFTCB0

2 reserved 00000000RW

Status

Flags

total byte count H

total byte count L

total byte count H

total byte count L

total byte count H

total byte count L

total byte count H

total byte count L

address byte

Mode

SET-UPDAT[0] = bmRequestType

SET-UPDAT[1] = bmRequest

SET-UPDAT[2:3] = wValue

SET-UPDAT[4:5] = wIndex

SET-UPDAT[6:7] = wLength

drive mode

[11]

GPIF Address H 0 0 0 0 0 0 0 GPIFA8 00000000 RW

[11]

GPIF Address L GPIFA7 GPIFA6 GPIFA5 GPIFA4 GPIFA3 GPIFA2 GPIFA1 GPIFA0 00000000 RW

Selector

Flowstate (when Logic = 0)

state (when Logic = 1)

Configuration

Edge Configuration

[11]

GPIF Transaction Count Byte 3

[11]

GPIF Transaction Count Byte 2

[11]

GPIF Transaction Count Byte 1

[11]

GPIF Transaction Count Byte 0

0 0 NPAK1 NPAK0 FULL EMPTY 0 STALL 00101000rrrrrrrb

0 NPAK2 NPAK1 NPAK0 FULL EMPTY 0 STALL 00000100 rrrrrrrb

0 0 NPAK1 NPAK0 FULL EMPTY 0 STALL 00000100rrrrrrrb

0 0 0 0 0 PF EF FF 00000010R

0 0 0 0 0 PF EF FF 00000110 R

0 0 0 BC12 BC11 BC10 BC9 BC8 00000000 R

BC7 BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000R

0 0 0 0 0 BC10 BC9 BC8 00000000 R

BC7 BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000R

0 0 0 0 BC11 BC10 BC9 BC8 00000000R

BC7 BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000R

0 0 0 0 0 BC10 BC9 BC8 00000000 R

BC7 BC6 BC5 BC4 BC3 BC2 BC1 BC0 00000000R

A15 A14 A13 A12 A11 A10 A9 A8 xxxxxxxx RW

A7 A6 A5 A4 A3 A2 A1 0 xxxxxxx0 bbbbbbbr

0 0 0 0 0 0 0 SDPAUTO 00000001 RW

DONE 0 0 0 0 0 0 IDLEDRV 10000000 RW

FSE 0 0 0 0 FS2 FS1 FS0 00000000brrrrbbb

CTL0E3 CTL0E2 CTL0E1/

SLAVE RDYASYNC CTLTOGL SUSTAIN 0 MSTB2 MSTB1 MSTB0 00100000 RW

0 0 0 0 0 0 FALLING RISING 00000001 rrrrrrbb

TC31 TC30 TC29 TC28 TC27 TC26 TC25 TC24 00000000RW

TC23 TC22 TC21 TC20 TC19 TC18 TC17 TC16 00000000RW

TC15 TC14 TC13 TC12 TC11 TC10 TC9 TC8 00000000RW

TC7 TC6 TC5 TC4 TC3 TC2 TC1 TC0 00000001 RW

CTL5

CTL0E0/ CTL4

CTL3 CTL2 CTL1 CTL0 00000000 RW

Document #: 38-08032 Rev. *K Page 32 of 60

Page 33

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 5-1. FX2LP Register Summary (continued)

Hex Size Name Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access

E6D2 1 EP2GPIFFLGSEL

E6D3 1 EP2GPIFPFSTOP Endpoint 2 GPIF stop

E6D4 1 EP2GPIFTRIG

E6DA 1 EP4GPIFFLGSEL

E6DB 1 EP4GPIFPFSTOP Endpoint 4 GPIF stop

E6DC 1 EP4GPIFTRIG

E6E2 1 EP6GPIFFLGSEL

E6E3 1 EP6GPIFPFSTOP Endpoint 6 GPIF stop

E6E4 1 EP6GPIFTRIG

E6EA 1 EP8GPIFFLGSEL

E6EB 1 EP8GPIFPFSTOP Endpoint 8 GPIF stop

E6EC 1 EP8GPIFTRIG

E6F0 1 XGPIFSGLDATH GPIF Data H

E6F1 1 XGPIFSGLDATLX Read/Write GPIF Data L &

E6F2 1 XGPIFSGLDATL-

E6F3 1 GPIFREADYCFG Internal RDY, Sync/Async,

reserved

3 reserved

reserved

3 reserved

reserved

3 reserved

reserved

3 reserved

NOX

[11]

Endpoint 2 GPIF Flag select

transaction on prog. flag

[11]

Endpoint 2 GPIF Trigger x x x x x x x x xxxxxxxx W

[11]

Endpoint 4 GPIF Flag select

transaction on GPIF Flag

[11]

Endpoint 4 GPIF Trigger x x x x x x x x xxxxxxxx W

[11]

Endpoint 6 GPIF Flag select

transaction on prog. flag

[11]

Endpoint 6 GPIF Trigger x x x x x x x x xxxxxxxx W

[11]

Endpoint 8 GPIF Flag select

transaction on prog. flag

[11]

Endpoint 8 GPIF Trigger x x x x x x x x xxxxxxxx W

(16-bit mode only)

trigger transaction Read GPIF Data L, no

transaction trigger

RDY pin states

0 0 0 0 0 0 FS1 FS0 00000000RW

0 0 0 0 0 0 0 FIFO2FLAG 00000000RW

0 0 0 0 0 0 FS1 FS0 00000000RW

0 0 0 0 0 0 0 FIFO4FLAG 00000000RW

0 0 0 0 0 0 FS1 FS0 00000000RW

0 0 0 0 0 0 0 FIFO6FLAG 00000000RW

0 0 0 0 0 0 FS1 FS0 00000000RW

0 0 0 0 0 0 0 FIFO8FLAG 00000000RW

D15 D14 D13 D12 D11 D10 D9 D8 xxxxxxxx RW

D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW

D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx R

INTRDY SAS TCXRDY5 0 0 0 0 0 00000000bbbrrrrr

E6F4 1 GPIFREADYSTAT GPIF Ready Status 0 0 RDY5 RDY4 RDY3 RDY2 RDY1 RDY0 00xxxxxx R E6F5 1 GPIFABORT Abort GPIF Waveforms x x x x x x x x xxxxxxxx W E6F6 2 reserved

E740 64 EP0BUF EP0-IN/-OUT buffer D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW E780 64 EP10UTBUF EP1-OUT buffer D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW E7C0 64 EP1INBUF EP1-IN buffer D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW E800 2048 reserved RW F000 1024 EP2FIFOBUF 512/1024-byte EP 2 /

F400 512 EP4FIFOBUF 512 byte EP 4 / slave FIFO

F600 512 reserved F800 1024 EP6FIFOBUF 512/1024-byte EP 6 /

FC00 512 EP8FIFOBUF 512 byte EP 8 / slave FIFO

FE00 512 reserved xxxx I²C Configuration Byte 0 DISCON 0 0 0 0 0 400KHZ xxxxxxxx

80 1 IOA 81 1 SP Stack Po inter D7 D6 D5 D4 D3 D2 D1 D0 00000111 RW 82 1 DPL0 Data Pointer 0 L A7 A6 A5 A4 A3 A2 A1 A0 00000000 RW 83 1 DPH0 Data Pointer 0 H A15 A14 A13 A12 A11 A10 A9 A8 00000000 RW 84 1 DPL1 85 1 DPH1 86 1 DPS 87 1 PCON Power Control SMOD0 x 1 1 x x x IDLE 00110000 RW

ENDPOINT BUFFERS

slave FIFO buffer (IN or OUT)

buffer (IN or OUT)

slave FIFO buffer (IN or OUT)

buffer (IN or OUT)

Special Function Registers (SFRs)

[13]

Port A (bit addressable) D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW

Data Pointer 1 L A7 A6 A5 A4 A3 A2 A1 A0 00000000 RW Data Pointer 1 H A15 A14 A13 A12 A11 A10 A9 A8 00000000RW Data Pointer 0/1 select 0 0 0 0 0 0 0 SEL 00000000RW

D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW

n/a

[14]

Notes:

13. SFRs not part of the standard 8051 architecture.

14. If no EEPROM is detected by the SIE then the default is 00000000.

Document #: 38-08032 Rev. *K Page 33 of 60

Page 34

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 5-1. FX2LP Register Summary (continued)

Hex Size Name Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access 88 1 TCON Timer/Counter Control

89 1 TMOD Timer/Counter Mode

8A 1 TL0 Timer 0 reload L D7 D6 D5 D4 D3 D2 D1 D0 00000000RW 8B 1 TL1 Timer 1 reload L D7 D6 D5 D4 D3 D2 D1 D0 00000000RW 8C 1 TH0 Timer 0 reload H D15 D14 D13 D12 D11 D10 D9 D8 00000000 RW 8D 1 TH1 Timer 1 reload H D15 D14 D13 D12 D11 D10 D9 D8 00000000 RW 8E 1 CKCON 8F 1 reserved 90 1 IOB 91 1 EXIF 92 1 MPAGE

93 5 reserved 98 1 SCON0 Serial Port 0 Control

99 1 SBUF0 Serial Port 0 Data Buffer D7 D6 D5 D4 D3 D2 D1 D0 00000000RW 9A 1 AUTOPTRH1 9B 1 AUTOPTRL1 9C 1 reserved 9D 1 AUTOPTRH2 9E 1 AUTOPTRL2 9F 1 reserved A0 1 IOC A1 1 INT2CLR A2 1 INT4CLR A3 5 reserved A8 1 IE Interrupt Enable

A9 1 reserved AA 1 EP2468STAT

AB 1 EP24FIFOFLGS

AC 1 EP68FIFOFLGS

AD 2 reserved AF 1 AUTOPTRSETUP B0 1 IOD B1 1 IOE

B2 1 OEA B3 1 OEB B4 1 OEC B5 1 OED B6 1 OEE B7 1 reserved B8 1 IP Interrupt Priority (bit ad-

B9 1 reserved BA 1 EP01STAT

BB 1 GPIFTRIG

BC 1 reserved BD 1 GPIFSGLDATH

BE 1 GPIFSGLDATLX BF 1 GPIFSGLDATL-

C0 1 SCON1

C1 1 SBUF1 C2 6 reserved C8 1 T2CON Timer/Counter 2 Control

C9 1 reserved CA 1 RCAP2L Capture for Timer 2, au-

CB 1 RCAP2H Capture for Timer 2, au-

CC 1 TL2 Timer 2 reload L D7 D6 D5 D4 D3 D2 D1 D0 00000000RW CD 1 TH2 Timer 2 reload H D15 D14 D13 D12 D11 D10 D9 D8 00000000RW CE 2 reserved

[13]

NOX

[13]

[13] [13]

[13]

[13, 11]

[13]

(bit addressable)

Control

Clock Control x x T2M T1M T0M MD2 MD1 MD0 00000001 RW

Port B (bit addressable) D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW External Interrupt Flag(s) IE5 IE4 I²CINT USBNT 1 0 0 0 00001000RW Upper Addr Byte of MOVX

using @R0 / @R1

(bit addressable)

[13]

Autopointer 1 Address H A15 A14 A13 A12 A11 A10 A9 A8 00000000 RW

[13]

Autopointer 1 Address L A7 A6 A5 A4 A3 A2 A1 A0 00000000 RW

[13]

Autopointer 2 Address H A15 A14 A13 A12 A11 A10 A9 A8 00000000 RW

[13]

Autopointer 2 Address L A7 A6 A5 A4 A3 A2 A1 A0 00000000 RW

Port C (bit addressable) D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW Interrupt 2 clear x x x x x x x x xxxxxxxx W Interrupt 4 clear x x x x x x x x xxxxxxxx W

(bit addressable)

[13]

Endpoint 2,4,6,8 status flags

Endpoint 2,4 slave FIFO status flags

Endpoint 6,8 slave FIFO status flags

[13]

Autopointer 1&2 set-up 0 0 0 0 0 APTR2INC APTR1INC APTREN 00000110 RW Port D (bit addressable) D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW Port E

(NOT bit addressable) Port A Output Enable D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW Port B Output Enable D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW Port C Output Enable D7 D6 D5 D4 D3 D2 D1 D0 00000000RW Port D Output Enable D7 D6 D5 D4 D3 D2 D1 D0 00000000RW Port E Output Enable D7 D6 D5 D4 D3 D2 D1 D0 00000000 RW

dressable)

[13]

Endpoint 0&1 Status 0 0 0 0 0 EP1INBSY EP1OUTBSYEP0BSY 00000000R

Endpoint 2,4,6,8 GPIF slave FIFO Trigger

[13]

GPIF Data H (16-bit mode only)

[13]

GPIF Data L w/ Trigger D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW GPIF Data L w/ No TriggerD7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx R

Serial Port 1 Control (b it addressable)

Serial Port 1 Data Buffer D7 D6 D5 D4 D3 D2 D1 D0 00000000RW

(bit addressable)

to-reload, up-counter

TF1 TR1 TF0 TR0 IE1 IT1 IE0 IT0 00000000 RW

GATE CT M1 M0 GATE CT M1 M0 00000000RW

A15 A14 A13 A12 A11 A10 A9 A8 00000000 RW

SM0_0 SM1_0 SM2_0 REN_0 TB8_0 RB8_0 TI_0 RI_0 00000000 RW

EA ES1 ET2 ES0 ET1 EX1 ET0 EX0 00000000 RW

EP8F EP8E EP6F EP6E EP4F EP4E EP2F EP2E 01011010 R

0 EP4PF EP4EF EP4FF 0 EP2PF EP2EF EP2FF 00100010 R

0 EP8PF EP8EF EP8FF 0 EP6PF EP6EF EP6FF 01100110 R

D7 D6 D5 D4 D3 D2 D1 D0 xxxxxxxx RW

1 PS1 PT2 PS0 PT1 PX1 PT0 PX0 10000000RW

DONE 0 0 0 0 RW EP1 EP0 10000xxx brrrrbbb

D15 D14 D13 D12 D11 D10 D9 D8 xxxxxxxx RW

SM0_1 SM1_1 SM2_1 REN_1 TB8_1 RB8_1 TI_1 RI_1 00000000 RW

TF2 EXF2 RCLK TCLK EXEN2 TR2 CT2 CPRL2 00000000RW

D7 D6 D5 D4 D3 D2 D1 D0 00000000RW

Document #: 38-08032 Rev. *K Page 34 of 60

Page 35

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Table 5-1. FX2LP Register Summary (continued)

Hex Size Name Description b7 b6 b5 b4 b3 b2 b1 b0 Default Access D0 1 PSW Program Status Word (bit

D1 7 reserved D8 1 EICON D9 7 reserved E0 1 ACC Accumulator (bit address-

E1 7 reserved E8 1 EIE

E9 7 reserved F0 1 B B (bit addressable) D7 D6 D5 D4 D3 D2 D1 D0 00000000RW F1 7 reserved F8 1 EIP

F9 7 reserved

[13]

addressable)

External Interrupt Control SMOD1 1 ERESI RESI INT6 0 0 0 01000000 RW

able)

External Interrupt Enable(s)

External Interrupt Priority Control

CY AC F0 RS1 RS0 OV F1 P 00000000RW

D7 D6 D5 D4 D3 D2 D1 D0 00000000RW

1 1 1 EX6 EX5 EX4 EI²C EUSB 11100000 RW

1 1 1 PX6 PX5 PX4 PI²C PUSB 11100000 RW

R = all bits read-only W = all bits write-only

r = read-only bit w = write-only bit b = both read/write bit

Document #: 38-08032 Rev. *K Page 35 of 60

Page 36

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

6.0 Absolute Maximum Ratings

Storage Temperature . .......... .......... .......... ......... ................. .......... .......... ......... .......... .......... ............. ....................–65°C to +150°C

Ambien t Temperatu re w ith Pow e r Su p p lie d (Co m m e rc ia l) .................... ......... .......... .......... .......... ......... ....................0°C to +70°C

Ambient Temperature with Power Supplied (Industrial) .................................................................................... ...–40°C to +105°C

Supply Voltage to Ground Potential.................................... .................... .. ............ .......... ............ ................... ......... –0.5V to +4.0V

DC Input Voltage to Any Input Pin . ...................................................................................................................................5.25V

DC Voltage Applied to Outputs in High Z State...................................................................................... ... .... – 0. 5 V to VC C + 0.5V

Power D is si pa ti on . ... .. .......... .......... .......... ................. ......... .......... .......... ......... .......... ................. .......... .......... ......... .......... 300 mW

Static Disch ar g e Voltage . ... ......... .......... .......... .......... ................. ......... .......... .......... .......... ................................................ > 2000V

Max Output Current, per I/O port ......................................................................................................................................... 10 mA

Max Output Current, all five I/O ports (128- and 100-pin packages).................................................................................... 50 mA

7.0 Operating Conditions

TA (Ambient Temperature Under Bias) Commercial.............. .................... .. .. .......... .. ............ .......... ......................... 0°C to +70°C

(Ambient Temperature Under Bias) Industrial................. ................................. ............................................ ...–40°C to +105°C

Supply Voltage............ ............ .................... .. ......................................................................................................+3.00V to +3.60V

Ground Voltage.......................................................................................................................................................................... 0V

(Oscillator or Crystal Frequenc y)....... .......... ................... .......... .......... ................... ...24 MHz ± 100 ppm, Parallel Resonant

OSC

[15]

8.0 Thermal C h ar acteristics

The following table displays the thermal characteri stics of various packages

Table 8-1. Thermal Characteristics

. Jc

Ambient Temperature

. a

Package

56 SSOP 70 24.4 23.3 47.7 100 TQFP 70 11.9 34.0 45.9 128 TQFP 70 15.5 27.7 43.2 56 QFN 70 10.6 14.6 25.2 56 VFBGA 70 30.9 27.7 58.6

The Junction Temperature

(°C)

. j, can be calculated using the following equation

Junc ti on to Cas e

Temperature

(°C/W)

. Ca

Case to Ambient

Temperature

(°C/W)

Junction to Ambient Temperature

. Ja

. Jc + . Ca

(°C/W)

. j = P*. Ja + . a

where, P = Power

. Ja = Junction to Ambient Temperature (. Jc + . Ca) . a = Ambient Temperature (70 C)

The Case Temperature

. c, can be calculated using the followi ng equation

. c = P*. Ca + . a

where, P = Power

. Ca = Case to Ambient Temperature . a = Ambient Temperature (70 C)

Notes:

15. It is recommended to not power I/O with chip power off.

Document #: 38-08032 Rev. *K Page 36 of 60

Page 37

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

9.0 DC Characteristics

Table 9-1. DC Characteristics

Parameter Description Conditions Min. Typ. Max. Unit

VCC Supply Voltage 3.00 3.3 3.60 V VCC Ramp Up 0 to 3.3V 200 ∝s V

IH_X

IL_X

SUSP

RESET

Input HIGH Voltage 2 5.25 V Input LOW Voltage –0.5 0.8 V Crystal Input HIGH Voltage 2 5.25 V Crystal Input LOW Vol tage –0.5 0.8 V Input Leakage Curr ent 0< VIN < VCC ±10 ∝A Output Voltage HIGH I Output LOW Voltage I

= 4 mA 2.4 V

OUT

= –4 mA 0.4 V

OUT

Output Current HIGH 4mA Output Current LOW 4mA Input Pin Capacitance Except D+/D– 10 pF

D+/D– 15 pF Suspend Current Connected 300 380 CY7C68014/CY7C68016 Disconnected 100 150 Suspend Current Connected 0.5 1.2 CY7C68013/CY7C68015 Disconnected 0.3 1.0

[16]

[16] [16] [16]

Supply Current 8051 running, con nected to USB HS 50 85 mA

8051 running, connected to USB FS 35 65 mA Reset Time after Valid Power VCC min = 3.0V 5.0 mS Pin Reset after powered on 200 ∝S

∝A ∝A

mA mA

Notes:

16. Measured at Max VCC, 25°C.

9.1 USB Transceiver

USB 2.0-compliant in full- and high-speed modes.

10.0 AC Electrical Characteristics

10.1 USB Transceiver

USB 2.0-compliant in full- and high-speed modes.

Document #: 38-08032 Rev. *K Page 37 of 60

Page 38

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

10.2 Program Memory Read

[17]

LKOUT

A[15..0]

STBH

PSEN#

D[7..0]

OE#

CS#

SOEL

SCSL

STBL

ACC1

[18]

data in

Figure 10-1. Program Memory Read Timing Diagram

T able 10-1. Program Memory Read Parameters

Parameter Description Min. Typ. Max. Unit Notes

STBL

STBH

SOEL

SCSL

DSU

Notes:

17. CLKOUT is shown with positive polarity.

18. t

is computed from the above parameters as follows:

ACC1

(24 MHz) = 3*tCL – tAV – t

ACC1

(48 MHz) = 3*tCL – tAV – t

ACC1

1/CLKOUT Frequency 20.83 ns 48 MHz

Delay from Clock to Valid Address 0 10.7 ns Clock to PSEN Low 0 8 ns Clock to PSEN High 0 8 ns Clock to OE Low 1 1.1 ns Clock to CS Low 13 ns Data Set- u p to Cl o ck 9.6 ns Data Hold Time 0 ns

= 106 ns

DSU

= 43 ns.

DSU

41.66 ns 24 MHz

83.2 ns 12 MHz

Document #: 38-08032 Rev. *K Page 38 of 60

Page 39

A A

10.3 Data Memory Read

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Stretch = 0

CLKOUT

[17]

A[15..0]

RD#

CS#

OE#

D[7..0]

[17]

A[15..0]

RD#

CS#

D[7..0]

DSU

ACC1

[19]

STBH

STBL

SCSL

SOEL

[19

ACC1

data in

Stretch = 1

DSU

data in

Figure 10-2. Data Memory Read Timing Diagram

T able 10-2. Data Memory Read Parameters

Parameter Description Min. Typ. Max. Unit Notes

1/CLKOUT Frequency 20.83 ns 48 MHz

41.66 ns 24 MHz

83.2 ns 12 MHz

STBL

STBH

SCSL

SOEL

DSU

Delay from Clock to Valid Address 10.7 ns Clock to RD LOW 11 ns Clock to RD HIGH 1 1 ns Clock to CS LOW 13 ns Clock to OE LOW 1 1.1 ns Data Set- u p to Cl o ck 9.6 ns Data Hold Time 0 ns

When using the AUTPOPTR1 or AUTOPTR2 to address external memory, the address of AUTOPTR1 will only be active while either RD# or WR# are activ e. The add res s of AUTOP TR2 wi ll b e acti ve thro ughout t he cy cle and mee t the ab ove ad dress va lid time for which is based on the stretch value

Note:

19. t

and t

ACC2

(24 MHz) = 3*tCL – tAV –t

ACC2

(48 MHz) = 3*tCL – tAV – t

ACC2

(24 MHz) = 5*tCL – tAV –t

ACC3

(48 MHz) = 5*tCL – tAV – t

ACC3

are computed from the above parameters as follows:

ACC3

DSU

= 106 ns

= 43 ns

= 190 ns

= 86 ns.

Document #: 38-08032 Rev. *K Page 39 of 60

Page 40

A A

10.4 Data Memory Write

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

CLKOUT

A[15..0]

WR#

CS#

D[7..0]

CLKOUT

A[15..0]

WR#

CS#

D[7..0]

SCSL

ON1

STBL

data out

STBH

Stretch = 1

data out

OFF1

Figure 10-3. Dat a Me mory Write Timing Dia gram

Table 10-3. Data Memory Write Parameters

Parameter Description Min. Max. Unit Notes

STBL

STBH

SCSL

ON1

OFF1

Delay from Clock to Valid Address 0 10. 7 ns Clock to WR Pulse LOW 0 11.2 ns Clock to WR Pulse HIGH 0 11.2 ns Clock to CS Pulse LOW 13.0 ns Clock to Data Turn-on 0 13.1 ns Clock to Data Hold Time 0 13.1 ns

When using the AUTPOPTR1 or AUTOPTR2 to address external memory, the address of AUTOPTR1 will only be active while either RD# or WR# are active. The address of AUTOPTR2 will be active throughout the cycle and meet the above address valid time for which is based on the stretch value.

Document #: 38-08032 Rev. *K Page 40 of 60

Page 41

A A

10.5 PORTC Strobe Feature Timings

The RD# and WR# are present in t he 100-pin ver sion and the 128-pin package. In these 100-pin and 128-pin versions, an 8051 control bit can be set to pulse the RD# and WR# pins when the 8051 reads from/writes to PORTC. This feature is enabled by setting PORTCSTB bi t i n CPUCS regis ter.

The RD# and WR# strobes are asserted for two CLKOUT cycles when PORTC is accessed.

The WR# strobe will be asserted two clock cycles after PORTC is updated and wi ll be a ctive for two c lock cyc les af t er that as shown in Figure 10-4.

As for read, the value of PORTC three cloc k cycles befor e the assertion of RD# is the value that the 8051 reads in. The RD# is pulsed for 2 clock cycles after 3 clock cycles from the point when the 8051 has performed a rea d function on PORTC.

CLKOUT

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

The way the feature is intended to work is that the RD# signal will prompt the external logic to prepare the next data byte. Nothing get s sampled int ernally on ass ertion of the RD# signal itself . It is ju st a “pre fetch” type sig nal to get the next dat a byte prepared. So, using it with that in mi nd should easily meet the set-up time to the next read.

The purpose of this pulsing of RD# is to let the external peripheral know t hat the 8051 i s done readi ng PORTC and th e data was latched into PORTC three CLKOUT cycles prior to asserting the RD# signal . Once the RD# is pulsed the external logic may update th e data on PORTC.

Following is the timing diagram of the read and write strobing function on accessing PORTC. Refer to Section 10.3 and Section 10.4 for det ails on pr opagation delay of RD# and WR# signals.

PORTC IS UPDATED

WR#

CLKOUT

8051 READS PORTC

RD#

STBL

STBH

Figure 10-4. WR# Strobe Function when PORTC is Accessed by 8051

CLKOUT

DATA MUST BE HELD FOR 3 CLK CYLCES

DATA CAN BE UPDATED BY EXTERNAL LOGIC

STBL

Figure 10-5. RD# Strob e Functi on w hen PORT C is Accessed by 8051

STBH

Document #: 38-08032 Rev. *K Page 41 of 60

Page 42

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

10.6 GPIF Synchronous Si gnals

IFCLK

SGA

GPIFADR[8:0]

RDY

SRY

XGD

valid

RYH

DAH

N+1

[20, 21]

[20]

DATA(input)

SGD

CTL

XCTL

DATA(output)

Figure 10-6. GPIF Synchronous Signals Timing Diagram

Table 10-4. GPIF Synchronous Signals Parameters with Internally Sourced IFCLK

Parameter Description Min. Max. Unit

IFCLK

SRY

RYH

SGD

DAH

SGA

XGD

XCTL

IFCLK Period 20.83 ns RDYX to Clock Set-up Time 8.9 ns Clock to RDYX 0ns GPIF Data to Clock Set-up Time 9.2 ns GPIF Data Hold Time 0 ns Clock to GPIF Address Propagation Delay 7.5 ns Clock to GPIF Data Output Propagation Delay 11 ns Clock to CTLX Output Propagation Delay 6.7 ns

Table 10-5. GPIF Synchronous Signals Parameters with Externally Sourced IFCLK

[21]

Parameter Description Min. Max. Unit

IFCLK

SRY

RYH

SGD

DAH

SGA

XGD

XCTL

Notes:

20. Dashed lines denote signals with programmable polarity.

21. GPIF asynchronous RDY

22. IFCLK must not exceed 48 MHz.

IFCLK Period RDYX to Clock Set-up Time 2.9 ns Clock to RDYX 3.7 ns GPIF Data to Clock Set-up Time 3.2 ns GPIF Data Hold Time 4.5 ns Clock to GPIF Address Propagation Delay 11.5 ns Clock to GPIF Data Output Propagation Delay 15 ns Clock to CTLX Output Propagation Delay 10.7 ns

signals have a minimum Set-up time of 50 ns when using internal 48-MHz IFCLK.

[22]

20.83 200 ns

Document #: 38-08032 Rev. *K Page 42 of 60

Page 43

A A

10.7 Slave FIFO S y nchronous R ead

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

IFCLK

SLRD

FLAGS

DATA

SLOE

OEon

Figure 10-7. Slave FIFO Synchronou s Read Timing Diagram

T able 10-6. Slave FIFO Synchronous Read Param eters with Internal ly Sourced IFCLK

SRD

RDH

XFLG

XFD

N+1

OEoff

[20]

[21]

Parameter Description Min. Max. Unit

IFCLK

SRD

RDH

OEon

OEoff

XFLG

XFD

IFCLK Period 20.83 ns SLRD to Clock Set-up Time 18.7 ns Clock to SLRD Hold Time 0 ns SLOE Turn-on to FIFO Data Valid 10.5 ns SLOE Turn-off to FIFO Data Hold 10.5 ns Clock to FLAGS Output Propagati on Delay 9.5 ns Clock to FIFO Data Output Propagation Delay 11 ns

Table 10-7. Slave FIFO Synchronous Read Parameters with Externally Sourced IFCLK

[21]

Parameter Description Min. Max. Unit

IFCLK

SRD

RDH

OEon

OEoff

XFLG

XFD

IFCLK Period 20.83 200 ns SLRD to Clock Set-up Time 12.7 ns Clock to SLRD Hold Time 3.7 ns SLOE Turn-on to FIFO Data Valid 10.5 ns SLOE Turn-off to FIFO Data Hold 10.5 ns Clock to FLAGS Output Propagati on Delay 13.5 ns Clock to FIFO Data Output Propagation Delay 15 ns

Document #: 38-08032 Rev. *K Page 43 of 60

Page 44

A A

10.8 Slave FI FO Asynchr onous Read

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

RDpwh

SLRD

FLAGS

DATA

SLOE

OEon

Figure 10-8. Slave FIFO Asynchronous Read Timing Diagram

T able 10-8. Slave FIFO Asynchronous Read Parameters

RDpwl

XFD

[23]

XFLG

N+1

OEoff

[20]

Parameter Description Min. Max. Unit

RDpwl

RDpwh

XFLG

XFD

OEon

OEoff

Note:

23. Slave FIFO asynchronous parameter values use internal IFCLK setting at 48 MHz.

SLRD Pulse Width LOW 50 ns SLRD Pulse Width HIGH 50 ns SLRD to FLAGS Output Propagation Delay 70 ns SLRD to FIFO Data Output Propagation Delay 15 ns SLOE Turn-on to FIFO Data Valid 10.5 ns SLOE Turn-off to FIFO Data Hold 10.5 ns

Document #: 38-08032 Rev. *K Page 44 of 60

Page 45

A A

10.9 Slave FIFO S y nchronous Writ e

IFCLK

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

IFCLK

SLWR

DATA

FLAGS

Figure 10-9. Slave FIFO Synchronous Write Timing Diagra m

Table 10-9. Slave FIFO Synchronous Write Parameters with Internally Sourced IFCLK

SWR

SFDtFDH

WRH

XFLG

[20]

[21]

Parameter Description Min. Max. Unit

IFCLK

SWR

WRH

SFD

FDH

XFLG

Table 10-10. Slave FIFO Synchronous Write Parameters with Externally Sourced IFCLK

IFCLK Period 20.83 ns SLWR to Clock Set-up Time 18.1 ns Clock to SLWR Hold Time 0 ns FIFO Data to Clo c k S e t- up Time 9.2 ns Clock to FIFO Da ta H o ld Time 0 ns Clock to FLAGS Output Propagati on Time 9.5 ns

[21]

Parameter Description Min. Max. Unit

IFCLK

SWR

WRH

SFD

FDH

XFLG

IFCLK Period 20.83 200 ns SLWR to Clock Set-up Time 12.1 ns Clock to SLWR Hold Time 3.6 ns FIFO Data to Clo c k S e t- up Time 3.2 ns Clock to FIFO Da ta H o ld Time 4.5 ns Clock to FLAGS Output Propag ati on Time 13.5 ns

Document #: 38-08032 Rev. *K Page 45 of 60

Page 46

A A

10.10 Slave FIFO Asyn chr onous Write

SLWR

SLWR/SLCS#

DATA

FLAGS

WRpwl

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

WRpwh

FDH

SFD

XFD

Figure 10-10. Slave FIFO Asynchronous Write Timing Diagram

T able 10-1 1. Slave FIFO Asynchronous Write Parameters with Internally Sourced IFCLK

[20]

[23]

Parameter Description Min. Max. Unit

WRpwl

WRpwh

SFD

FDH

XFD

SLWR Pul se LOW 50 ns SLWR Pul se HIGH 70 ns SLWR to FIFO DATA Set-up Time 10 ns FIFO DATA to SLWR Hold Time 10 ns SLWR to FLAGS Output Pr opagation Delay 70 ns

10.11 Slave FI FO Sync hro nous Pa cket End Strobe

IFCLK

PEH

PKTEND

FLAGS

Figure 10-11. Slave FIFO Synchronou s Packet End Strobe Timing Diagra m

Table 10-12. Slave FIFO Synchronous Packet End Strobe Parameters with Internally Sourced IFCLK

Parameter Description Min. Max. Unit

IFCLK

SPE

PEH

XFLG

IFCLK Period 20.83 ns PKTEND to Clock Set-up Time 14.6 ns Clock to PKTEND Hold Time 0 ns Clock to FLAGS Output Propagati on Delay 9.5 ns

SPE

XFLG

[20]

[21]

T able 10-13. Slave FIFO Synchronous Packet End Strobe Parameters with Externally Sourced IFCLK

[21]

Parameter Description Min. Max. Unit

IFCLK

SPE

PEH

XFLG

There is no specific timing requirement that needs to be met for asserting PKTEND pin with regards to asserting SLWR. PKTEND can be asserted with t he last da ta val ue cl ocked into the FIFOs or thereafter. The only consideration is the set-up time t

and the hold time t

SPE

IFCLK Period 20.83 200 ns PKTEND to Clock Set-up Time 8.6 ns Clock to PKTEND Hold Time 2.5 ns Clock to FLAGS Output Propagati on Delay 13.5 ns

Although there are no specific timing requirements for the PKTEND assertion, there is a specific corner case condition that needs at tenti on whil e using t he PKTEND to commi t a one byte/word packet. There is an additional timing requirement

must be met.

PEH

that need to be met when the FIFO is configured to operate in

Document #: 38-08032 Rev. *K Page 46 of 60

Page 47

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

auto mode and it is desired to send t wo packets back to back: a full packet (full defined as the number of bytes in the FIFO meeting the level set in AUTOINLEN register) committed automatically followed by a short one byte/word packet committed manually using the PKTEND pin. In this particular scenario, user must make sure to assert PKTEND at leas t one clock cycle aft er the r ising edge that caus ed the last byt e/word to be clocked into the previous auto committed packet. Figure 10-12 below shows this scenario. X is the value the AUTOINLEN register is set to when the IN endpoint is configured to be in auto mode.

IFCLK

SFA

FIFOADR

>= t

SWR

SLWR

DATA

SFD

X-4

FDH

SFD

X-3

FDH

SFD

Figure 10-12 shows a scenario where two packets are being committed. The first packet gets committed automatically when the numb er of bytes in the FIFO reaches X (value set in AUTOINLEN register) and the second one byte/word short packet being committed manually using PKTEND. Note that there is at lea st one IF CLK cyc le ti ming betwe en the asse rt ion of PKTEND and clocking of the last byte of the previous pac ket (causing the packet to be commit ted automaticall y). Failing to adhere to this timing, will result in the FX2 failing to send the one byte/word short packet.

FAH

>= t

WRH

X-2

FDH

SFD

X-1

FDH

SFD

FDH

SFD

At least one IFCLK cycle

PKTEND

Figure 10-12. Slave FIFO Synchronous Write Sequence and Ti ming Diagram

[20]

10.12 Slave FI FO Asynchr ono us Packe t End Strobe

PEpwh

PKTEND

FLAGS

Figure 10-13. Slave FIFO Asynchr onous Packet End Strobe Timing Diagram

Table 10-14. Slave FIFO Asynchronous Packet End Strobe Parameters

Parameter Description Min. Max. Unit

PEpwl

PWpwh

XFLG

PKTEND Pulse Width LOW 50 ns PKTEND Pulse Width HIGH 50 ns PKTEND to FLAGS Output Propagation Del ay 115 ns

PEpwl

XFLG

[23]

[20]

SPE

PEH

Document #: 38-08032 Rev. *K Page 47 of 60

Page 48

A A

10.13 Slave FI FO Outpu t Enable

SLOE

DATA

OEon

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

OEoff

Figure 10-14. Slave FIFO Output Enable Timing Diagram

[20]

Table 10-15. Slave FIFO Output Enable Parameters

Parameter Description Min. Max. Unit

OEon

OEoff

SLOE Assert to FIFO DA TA Output 10.5 ns SLOE Deassert to FIFO DATA Hold 10.5 ns

10.14 Slave FIFO Address to Flags/Data

FIFOADR [1.0]

XFLG

FLAGS

XFD

DATA

Figure 10-15. Slave FIFO Address to Flags/Data Timing Diagram

Table 10-16. Slave FIFO Address to Flags/Data Parameters

Parameter Description Min. Max. Unit

XFLG

XFD

FIFOADR[1:0] to FLAGS Output Propagation Delay 10.7 ns FIFOADR[1:0] to FIFODATA Output Propagation Delay 14.3 ns

NN+1

[20]

Document #: 38-08032 Rev. *K Page 48 of 60

Page 49

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

10.15 Slave FIFO Sync hro nous Add ress

IFCLK

SLCS/FIFOADR [1:0]

SFAtFAH

Figure 10-16. Slave FIFO Synchr onous Address Timing Diagram

Table 10-17. Slave FIFO Synchronous Address Parameters

[21]

Parameter Description Min. Max. Unit

IFCLK

SFA

FAH

Interface Clock Period 20.83 200 ns FIFOADR[1:0] to Clock Set-up Time 25 ns Clock to FIFOADR[1:0] Hold Time 10 ns

10.16 Slave FIFO Asyn chr onous Address

SLCS/FIFOADR [1:0]

FAH

SLRD/SLWR/PKTEND

SFA

[20]

Figure 10-17. Slave FIFO Asynchro nous Address Timing Diagram

Slave FIFO Asynchronous Address Par am eter s

[23]

[20]

Parameter Description Min. Max. Unit

SFA

FAH

FIFOADR[1:0] to SLRD/SLWR/PKTEND Set-up T ime 10 ns RD/WR/PKTEND to FIFOADR[1:0] Hold Time 10 ns

Document #: 38-08032 Rev. *K Page 49 of 60

Page 50

A A

10.17 Sequence Diagram

10.17.1 Single and Burst Synchronous Read Example

IFCLK

FIFOADR

SLRD

SLCS

FLAGS

SFA

t=0

SRD

t=2

FAH

RDH

t=3

XFLG

T=0

SFA

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

FAH

T=2

>= t

SRD

>= t

RDH

T=3

XFD

DATA

SLOE

t=1

Data Driven: N

OEon

N+1

OEoff

t=4

Figure 10-18. Slave FIFO Synchronous Read Sequence and Timing Diagram

FIFO POINTER

FIFO DATA BUS

IFCLK

NNN+1 N+2

SLOE

Not Driven Driven: N

IFCLK IFCLK IFCLK IFCLK

SLRD

SLOE SLRD

N+1 N+2

Not Driven

Figure 10-19. Slave FIFO Synchr onous Sequence of Events Diagram

Figure 10-18 shows the timing r elationshi p of the SLAVE FIFO signals during a synchronous FIFO read using IFCLK as the synchronizing clock. The diagram illustrates a single read followed by a burst read.

• At t = 0 the FI FO address is stable and the signal SLCS is asserted (SLCS may be tied low in some applications). Note: t is running a t 48 MHz, t he FIFO ad dress set- up time i s more

has a minimum of 25 ns. This means when IFCLK

SFA

than one IFCLK cycle.

• At t = 1, SLOE is asser ted. SLOE is an ou tput enable onl y, whose sole function is to drive the data bus. The data that is driven on the bu s is the data t hat the internal FI FO pointer is currently poin ti ng to. In this example it is the first data value in the FIFO. Note : the data is pre-fetched and is driven on the bus when SLOE is asserted.

• At t = 2, SLRD i s asserted. SLRD must meet t he set-up time of t

(time from asserting the SLRD signal to the rising

SRD

edge of the IFCLK) and maintain a minimum hold time of t

(time from the IFCLK edge to the deassertion of the

RDH

SLRD signal). If the SLCS signal is us ed, it must be asse rted

N+1

OEon

SLOE

T=1

N+1

XFD

SLRD

N+2

N+3

XFD

IFCLK

N+4

N+3

SLRD

XFD

N+4

OEoff

T=4

[20]

IFCLK IFCLKIFCLK IFCLK

N+4

SLOE

N+4

before SLRD is asserted (i. e., the SLCS and SLRD signals must both be asserted to start a vali d read condition).

• The FIFO point er is updated on the r ising edge of t he IFCLK, while SLRD is asserte d. This st arts the prop agation of data from the newly addressed location to the data bus. After a propagation delay of t of IFCLK) the new data value is present. N is the first data

(measured from the rising edge

XFD

value read from the FIFO. In order to hav e data on the FIFO data bus, SLOE MUST also be asserted.

The same sequence of events are shown for a burst read and are marked with the time indicators of T = 0 through 5. Note: For the burst mode, the SLRD and SLOE are left asserted during the ent ir e duration of the read. In t he burst read mode, when SLOE is asserted, data indexed by the FIFO pointer is on the data bus. Dur ing the first read cycle, on the rising edge of the clock the FIFO pointer is updated and increments to point to address N+1. For each subsequent rising edge of IFCLK, while the SLRD is asserted, the FIF O pointer is incremented and the next data value is placed on the data bus.

N+4

Not Driven

Document #: 38-08032 Rev. *K Page 50 of 60

Page 51

A A

10.17.2 Single and Burst Synchronous Write

IFCLK

SFA

FIFOADR

t=0

SLWR

SLCS

FLAGS

DATA

PKTEND

SWR

WRH

t=2

t=3

XFLG

FDH

SFD

t=1

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

T=0

SFA

>= t

SWR

T=2 T=5

FDH

T=3

SFD

N+2

FDH

T=4

T=1

SFD

N+1

SFD

N+3

SPE

>= t

XFLG

FDH

FAH

WRH

PEH

FAH

Figure 10-20. Slave FIFO Synchronous Write Sequence and Ti ming Diagram

The Figure 10-20 shows the timing relationship of the SLAVE FIFO signals during a synchronous write using IFCLK as the synchronizing clock. The diagram illustrates a single write followed by burst wri te of 3 bytes an d com mitting al l 4 bytes as a short packet using the PKTEND pin.

• At t = 0 the FI FO address is stable and the signal SLCS is asserted. (SLCS may be tied low in some applications) Note: t is running a t 48 MHz, t he FIFO ad dress set- up time i s more

has a min imum of 25 ns. This means when IFCLK

SFA

than one IFCLK cycle.

• At t = 1, the external master/peripheral must outputs the data value onto the da ta b us wit h a minimum set u p ti me of t

before the rising edge of IFCLK.

SFD

• At t = 2, SLWR is asser ted. The SLWR must meet the set- up time of t rising edge of IFCLK) an d maintain a mi nimum hold time of t

WRH

SL WR si gnal). If SLCS signal is used , it mu st be asserted

(time from asserting the SL WR si gnal to the

SWR

(time from the IFCLK edge to the deas sertion of the

with SL WR or before SL WR is asserted. (i.e., the SLCS and SL WR si gnals must both be asserted to start a valid write condition).

• While th e SL WR is asserted, data is writ ten to the FIFO an d on the rising edge of the IFCL K, the FIFO pointer is incremented. The FI FO flag wi ll also be updated af ter a de lay of t

from the rising edge of th e clock.

XFLG

The same sequen ce o f event s ar e a lso sho wn f or a bu rst wr ite and are marked with the time indicators of T = 0 through 5. Note: For the burst mode, SLWR and SLCS are left asserted for the entire d urati on of wri ting all the r equired data va lu es. In this burst write mod e, once the SL WR is asser ted, the dat a on the FIFO data bus is written to the FIFO on every rising edge

[20]

of IFCLK. The FIF O po int er is updated on each rising edge of IFCLK. In Figure 10-20, once the four bytes are written to the FIFO, SLW R is deasserted. The short 4-byte packet can be committed to the host by asserting the PKTEND signal.

There is no specific timing requirement that needs to be met for asserting PKTEND signal with regards to asserting the SLWR signal. PKTEND can be asserted with the last data value or ther eafter . The only require ment is that the set-u p time t

and the hold time t

SPE

Figure 10-20, the number of data values committed includes

must be met. In the scenario of

PEH

the last value written to the FIFO. In this example, both the data value and the PKTEND signal are clocked on the same rising edge of IFCLK. PKTEND can also be asserted in subsequent clock cycles. The FIFOADDR lines should be held constant during the PKTEND assertion.

Although there are no specific timing requirement for the PKTEND assertion, there is a specific corner case condition that needs at tenti on whil e using t he PKTEND to commi t a one byte/word packet. Additional timing requirements exi sts when the FIFO is configur ed to operate in auto mode and it is desi red to send two packets: a full packet (full defined as the number of bytes in the FIFO meeting the level set in AUTOINLEN register) committed automatically followed by a short one byte/word p acket com mitt ed manua lly using the PKTEND pin. In this case, the exter nal master must make sur e to asser t the PKTEND pin at least one clock cycle aft er the ris ing edge that caused the last byte/wor d t o be clocked into the prev ious aut o committed packet (the packet with the number of bytes equal to what is set in the AUTOINLEN register). Refer to Figure 10-12 for further details on this timing.

Document #: 38-08032 Rev. *K Page 51 of 60

Page 52

A A

10.17.3 Sequence Diagram of a Single and Burst Asynchr onous Read

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

FIFOADR

SLRD

SLCS

FLAGS

DATA

SLOE

FIFO POINTER

SFA

t=0

t=1

Data (X )

Driven

OEon

t=2

RDpwl

FAH

RDpwh

t=3

XFLG

XFD

OEoff

t=4

SFA

T=0

T=2 T=3

OEon

T=1 T=7

RDpwl

XFD

RDpwh

N+1

T=4

RDpwl

RDpwh

T=5

XFD

T=6

N+2

Figure 10-21. Slave FIFO Asynchronous Read Seque nce and Timing Diagr am

SLOE SLRD

SLRD

N+1

SLOE

N+1

SLRD

N+1

SLRD

N+2

RDpwl

SLRD

FAH

RDpwh

XFLG

XFD

N+3

OEoff

[20]

SLOE

N+3

N+2

SLRD

N+3

FIFO DATA BUS Not Driven Driven: X

N Not Drive

Not Driven

Figure 10-22. Slave FIFO Asynch ronous Read Sequence of Events Diagram

Figure 10-21 diagrams the timing relationship of the SLAVE FIFO signals during an asynchronous FIFO read. It shows a single read followed by a burst read.

• At t = 0 the FI FO address is stable and the SLCS signal is asserted.

• At t = 1, SL OE is asserted. This results i n the data bus being driven. The data that i s driven on to the bus is previous data, it data that was in the FIFO from a prior read cycle.

• At t = 2, SLRD is asserted. The SLRD must meet the minimum active pulse of t pulse widt h of t asserted befo re SLRD is asserted (i. e., the SLCS and SLRD

. If SLCS is us ed t hen, SLCS must be

RDpwh

and minimum de-active

RDpwl

signals must both be asserted to start a valid read condition.)

N+1

N+2

• The data that will be dri ven, after assert ing SLRD, is the updated data fr om the FIFO. This data is valid af ter a propagation delay of t Figure 10-21, data N is the first valid data read fr om the

from the activating edge of SLRD. In

XFD

FIFO. For data to appear on the data bus during the read cycle (i.e.,SLRD is asserted), SLOE MUST be in an asserted state. SLRD and SLOE can also be tied together.

The same sequence of events is also shown for a burst read marked with T = 0 throu gh 5. Note: In burst r ead mode, durin g SLOE is asse rtion, the data bus i s in a dri ven stat e and output s the previous data. Once SLRD is asserted, the data from the FIFO is driven on the data bus (SLOE must also be asserted) and then the FIFO pointer is incremented.

Document #: 38-08032 Rev. *K Page 52 of 60

Page 53

A A

10.17.4 Sequence Diagram of a Single and Burst Asynchr onous Write

T=0

SFA

T=1

WRpwl

T=2

WRpwh

T=3

SFD

FDH

N+1

T=4

WRpwl

T=5

FIFOADR

SLWR

SLCS

FLAGS

DATA

PKTEND

t=0

SFA

WRpwl

t =1 t=3

SFD

t=2

WRpwh

FDH

FAH

XFLG

SFD

T=6

WRpwh

FDH

N+2

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

FAH

WRpwl

WRpwh

T=7

T=9

XFLG

SFD

FDH

N+3

T=8

PEpwl

PEpwh

Figure 10-23. Slave FIFO Asynchronous Write Sequ ence and Timing Diagram

Figure 10-23 diagrams the timing relationship of the SLAVE FIFO write in an asynchronous mode. The diagram shows a single write foll owed by a burst wri te of 3 bytes and com mitting the 4-byte-short packet using PKTEND.

• At t = 0 the FIFO address is appli ed, insuring that it meets the set-up time of t asserted (SLCS may be tied low in some applications).

. If SLCS is use d , it m u s t als o be

SFA

• At t = 1 SLW R is asserted. SLWR must meet the mini mum active pulse of t of t SLWR or before SLWR is asserted.

. If the SLCS is used, it must be in ass ert ed with

WRpwh

• At t = 2, data must be pr esent on the bus t deasserting edge of SLWR.

and minimum de-activ e pulse width

WRpwl

SFD

before the

• At t = 3, deass erting SL W R will cause the da ta to be writt en from the dat a bus to t he FIFO and then increments the FIFO

[20]

pointer. The FIFO flag is also updated after t deasserting edge of SLWR.

XFLG

from the

The same sequence of event s are shown f or a burst write an d is indicated by the timing marks of T = 0 through 5. Note: In the burst write mode, once SLWR is deasserted, the data is written to the FIFO and then the FIFO pointer is incremented to the next byte in the FIFO. The FIFO pointer is post incremented.

In Figure10-23 once the four bytes are written to t he FIFO and SLWR is deasserted, the short 4-byte packet can be committed to the host usi ng the PKTEND. The extern al device should be designed to not assert SLWR and the PKTEND signal at the same time. It should be designed to assert the PKTEND after SLWR is deasserted and met the minimum deasserted pulse width. The FIFOADDR lines are to be held constant during the PKTEND assertion.

Document #: 38-08032 Rev. *K Page 53 of 60

Page 54

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

11.0 Ordering Information

Table 11-1. Ordering Information

Ordering Code Package Type RAM Size # Prog I/Os

Ideal for battery powered applications

CY7C68014A-128AXC 128 TQFP – Lead-Free 16K 40 16/8 bit CY7C68014A-100AXC 100 TQFP – Lead-Free 16K 40 – CY7C68014A-56PVXC 56 SSOP – Lead-Free 16K 24 – CY7C68014A-56LFXC 56 QFN – Lead-Free 16K 24 – CY7C68014A-56BAXC 56 VFBGA – Lead-Free 16K 24 – CY7C68016A-56LFXC 56 QFN – Lead-Free 16K 26 –

Ideal for non-battery powered applications

CY7C68013A-128AXC 128 TQFP – Lead-Free 16K 40 16/8 bit CY7C68013A-128AXI 128 TQFP – Lead-Fr ee (Industrial ) 16K 40 16/ 8 bit CY7C68013A-100AXC 100 TQFP – Lead-Free 16K 40 – CY7C68013A-100AXI 100 TQFP – Lead-Free (Industr ial) 16K 40 – CY7C68013A-56PVXC 56 SSOP – Lead-Free 16K 24 – CY7C68013A-56PVXI 56 SSOP – Lead-Free (Industrial) 16K 24 – CY7C68013A-56LFXC 56 QFN – Lead-Free 16K 24 – CY7C68013A-56LFXI 56 QFN – Lead-Free (Industrial) 16K 24 – CY7C68015A-56LFXC 56 QFN – Lead-Free 16K 26 – CY7C68013A-56BAXC 56 VFBGA – Lead-Free 16K 24 –

8051 Address

/Data Busses

Development Tool Kit

CY3684 EZ-USB FX2LP Development Kit

Reference Design Kit

CY4611B USB 2.0 to ATA/ATAPI Reference Design using EZ-USB FX2LP

Document #: 38-08032 Rev. *K Page 54 of 60

Page 55

A A

12.0 Package Diagrams

The FX2LP is available in five packages:

• 56-pin SSOP

• 56-pin QFN

• 100-pin TQFP

• 128-pin TQFP

• 56-ball VFBGA

Package Diagrams

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

0.80[0.031]

Figure 12-1. 56-lead Shrunk Small Outline Package O56

TOP VIEW

DIA.

7.90[0.311]

8.10[0.319]

7.70[0.303]

7.80[0.307]

7.70[0.303]

1.00[0.039] MAX.

0.80[0.031] MAX.

8.10[0.319]

7.90[0.311]

SIDE VIEW

0°-12°

0.08[0.003]

0.05[0.002] MAX.

0.20[0.008] REF.

0.30[0.012]

0.50[0.020]

SEATING PLANE

BOTTOM VIEW

E-PAD

(PAD SIZE VARY BY DEVICE TYPE)

6.45[0.254]

6.55[0.258]

0.18[0.007]

0.28[0.011]

0.50[0.020]

PIN1 ID

0.20[0.008] R.

0.45[0.018]

0.24[0.009]

0.60[0.024]

51-85062-*C

6.55[0.258]

6.45[0.254]

(4X)

51-85144-*D

Figure 12-2. 56-Lea d QFN 8 x 8 mm LF56A

Document #: 38-08032 Rev. *K Page 55 of 60

Page 56

A A

Package Diagrams (continued)

16.00±0.20

14.00±0.10

100

20.00±0.10

22.00±0.20

31 50

R 0.08 MIN.

0.20 MAX.

0.25

0°-7°

0.60±0.15

1.00 REF.

0° MIN.

R 0.08 MIN.

0.20 MAX.

0.20 MIN.

DETAIL

Figure 12-3. 100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) A100RA

0.30±0.08

0.65 TYP.

STAND-OFF

0.05 MIN.

0.15 MAX.

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

1.40±0.05

12°±1°

(8X)

SEATING PLANE

NOTE:

1. JEDEC STD REF MS-026

2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH

MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE

BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH

3. DIMENSIONS IN MILLIMETERS

SEE DETAIL

0.20 MAX.

1.60 MAX.

0.10

51-85050-*B

Document #: 38-08032 Rev. *K Page 56 of 60

Page 57

A A

Package Diagrams (continued)

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

R 0.08 MIN.

0.20 MAX.

0.25

0°-7°

0.60±0.15

1.00 REF.

20.00±0.10

22.00±0.20

0° MIN.

R 0.08 MIN.

0.20 MAX.

0.20 MIN.

DETAIL

16.00±0.20

14.00±0.10

128

0.22±0.05

12°±1°

(8X)

STAND-OFF

0.05 MIN.

0.15 MAX.

0.50 TYP.

SEATING PLANE

NOTE:

1. JEDEC STD REF MS-026

2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH

MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE

BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH

3. DIMENSIONS IN MILLIMETERS

1.40±0.05

0.20 MAX.

1.60 MAX.

0.08

SEE DETAIL

51-85101-*C

Figure 12-4. 128- Lead Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) A128

Document #: 38-08032 Rev. *K Page 57 of 60

Page 58

A A

Package Diagrams (continued)

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

5.00±0.10

0.45

PIN A1 CORNER

13265486

D E F

SEATING PLANE

-C-

TOP VIEW

5.00±0.10

SIDE VIEW

BOTTOM VIEW

Ø0.05 M C

Ø0.15MCAB

Ø0.30±0.05(56X)

7856 2341

0.50

3.50

5.00±0.10

-B-

-A-

0.10(4X)

0.10 C

0.080 C

REFERENCE JEDEC: MO-195C

PACKAGE WEIGHT: 0.02 grams

0.50

3.50

5.00±0.10

A1 CORNER

D E F

0.21

1.0 max

0.160 ~0.260

001-03901-*B

Figure 12-5. 56 VFBGA (5 x 5 x 1.0 mm) 0.50 Pitch, 0.30 Ball BZ56

13.0 PCB Layout Recommendations

[24]

The following recommendations should be follow ed to ensure reliable high-performance operat ion.

• At least a four -l ayer impedance contr olled boards are required to maintain signal quality.

• Specify impedance targets (ask your board vendor what they can achieve).

• T o control impedance, maintain trace wid ths and trace spacing.

• Minimize stubs to minimize refl ected signals.

• Connections between the USB connector shell and signal ground must be done near the USB connector.

• Bypass/flyback caps on VBus, near connector, are recommended.

• DPLUS and DMINUS trace lengt hs should be kept to within 2 mm of each other in length, with preferred length of 20–30 mm.

ote:

24. Source for recommendations: EZ-USB FX2™PCB Design Recommendations, http://www.cypress.com/cfuploads/support/app_notes/FX2_PCB.pdf and Hig Speed USB Platform Design Guidelines, http://www.usb.org/developers/docs/hs_usb_pdg_r1_0.pdf.

• Maintain a solid ground plane under the DPLUS and DMINUS traces. Do not allow the plane to be split under these traces.

• It is preferre d is to have no vias placed on the DPLUS or DMINUS trace routing.

• Isolate the DPL US and DMINUS traces f rom all other s ignal traces by no less t han 10 mm.

14.0 Quad F l at Packag e N o Le ad s (QFN) Package D esign No tes

Electrical co ntact of t he part to the Printe d Circuit Board (PCB) is made by soldering the leads on the bottom surface of the package to the PCB. Hence , special attention is required to the heat transfer area below the package to provide a good thermal bond to the circuit board. A Copper (Cu) fill is to be designed into the PCB as a thermal pad under the package. Heat is transf er red from the FX2L P th rough t he devi ce’s met al paddle on the bottom side of the package. Heat from here, is conducted to the PCB at the thermal pad. It is then conducted

Document #: 38-08032 Rev. *K Page 58 of 60

Page 59

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

from the the rmal p ad t o the PCB inner ground pl ane by a 5 x 5 array of via. A via is a plated through hole in the PCB with a finished diameter of 13 mil. The QFN’ s me tal die paddle must be soldered to the PCB’s thermal pad. Solder mask is placed on the board top side over each via to resist solder flow into the via. The mask on the top side also minimizes outgassing during the solder reflow process.

For further information on this p ackage design please refer to the application note Surface Mount Assembly of AMKOR’s MicroLeadFrame ( MLF) Technology . This applica tion note ca n be downloaded from AMKOR’s website from the following URL http://www.amkor.com/products/notes_papers/MLF_AppNote _0902.pdf. The application note provides detail ed information on board moun ting guidel ines, solder ing f low, rework process, etc.

Solder Mask

Cu Fill

PCB Material

Via hole for thermally connecting the QFN to the circuit board ground plane.

Figure 14-1. Cross-section of the Area Underneath the QFN Package

Figure 14-1 below displ ays a cross- sec tiona l area underneat h the package. The cross section is of only one via. The solder paste template needs to be designed to allow at least 50% solder coverage. The thickness of the solder paste template should be 5 m il. It is recommended that “No Clean” type 3 solder paste is used for mounting the part. Nitrogen purge is recommended during ref low.

Figure 14-2 is a plot of the solder mask pattern and Figure 14-3 displays an X-Ray image of the asse mb ly (darker

areas indicate solder).

0.017” dia

Cu Fill

0.013” dia

This figure only shows the top three layers of the circuit board: Top Solder, PCB Dielectric, and the Ground Plane

PCB Material

Figure 14-2. Plot of the Solder Mask (White Area)

Figure 14-3. X-ray Imag e of the Assembly

Purchase of I

C Patent Rights to use these comp onents in an I2C system, provi ded that the s ystem conforms to the I2C Sta ndar d Sp eci fica tion

C components from Cypr ess, or o ne of its su blice nsed Asso ci ated Com pani es, c onvey s a lic ense unde r the Phi lip s

as defined by Philips. EZ-USB FX2LP, EZ-USB FX2 and ReNumeration are trademarks, and EZ-USB is a register ed trademark, of Cypress Semicond uct or Corporati on. All product and comp any names ment ioned i n this docu ment are the trademark s of thei r respective holders.

Document #: 38-08032 Rev. *K Page 59 of 60

© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress

Page 60

A A

CY7C68013A/CY7C68014 CY7C68015A/CY7C68016

Document History Page

Document Title: CY7C68013A EZ-USB FX2LP™ USB Microcont roller High-Speed USB Peripheral Controller Document Number: 38-08032

REV . ECN NO.

** 124316 03/17/03 VCS New data sheet

*A 128461 09/02/03 VCS Added PN CY7C68015A throughout data sheet

*B 130335 10/09/03 KKV Restored PRELIMINARY to header (had been removed in error from rev. *A) *C 131673 02/12/04 KKU Section 8.1 changed “certi fi ed” to “compliant”

*D 230713 See E CN KKU Changed Lead free Mar keting p art numbers in Table 11-1 as p er spec change in 28-00054. *E 242398 See ECN TMD Minor Change: data sheet posted to the web, *F 271169 See ECN MON Added USB-IF Test ID number

*G 316313 See ECN MON Removed CY7C68013A-56PVXCT part availability

*H 338901 See ECN MON Added information on the AUTOPTR1/AUTOPTR2 address timing with regards to data

*I 371097 See ECN MON Added timing for strobin g RD#/WR# signa ls when usi ng PortC s trobe fea ture (Sect ion 10.5 )

*J 397239 See ECN MON Removed XTALINSRC register from register summary.

*K 420505 See ECN MON Remove SLCS from figure in Section 10.10.

Issue

Date

Orig. of

Change Description of Change

Modified Figure 1-1 to add ECC block and fix errors Removed word “compatible” where associated with I Corrected grammar and fo rmatting in various locations Updated Sections 3.2.1, 3.9, 3.11, Table 3-9, Section 5.0 Added Sections 3.15, 3.18.4, 3.20 Modified Figure 3-5 for clari ty Updated Figure 12-2 to match current spec revision

Table 9-1 added parameter V Added Sequence diagrams Section 9.16 Updated Ordering information with lead-free parts Updated Registry Summar y Section 3.12.4:example changed to column 8 from column 9 Updated Figure 10-3 memory write timing Diagram Updated section 3.9 (reset) Updated section 3.15 ECC Generation

Added USB 2.0 logo Added values for Isusp, Icc, Power Dissipation, Vih_x, Vil_x Changed VCC from + Changed E-Pad size to 4.3 mm x 5.0 mm Changed PKTEND to FLAGS output propagation delay (asynchronous interface) in Table 10-14 from a max value of 70 ns to 115 ns

Added parts ideal for battery powered applications: CY7C68014A, CY7C68016A Provided addition al timing restr ictions and req uirement reg arding the use of PKETEND pin to commit a short one byt e /word packet sub sequent to committing a packet automatically (when in auto mode). Added Min Vcc Ramp Up time (0 to 3.3v)

memory read/write timing diagram. Removed TBD for Min value of Clock to FIFO Data Output Propagatio n Delay (t Slave FIFO Synchronous Read Changed Table 11-1 to include part CY7C68016A- 56LFXC in the part listed for batt ery powered applications Added register GPCR2 in register summary

Changed Vcc margins to + Added 56-pin VFBGA Pin Package Diagram Added 56-pin VFBGA definiti on in pin listing Added RDK part number to the Ordering Information table

Removed indicati ons that SLRD can be asserted simultaneously with SLCS in Section

10.17.2 and Section 10.17.3 Added Absolute Maximum Temperature Rating for industrial packages in Section 6.0 Changed number of packages stated in the description in Section 4.0 to five. Added Table 8-1 on Thermal Coefficients for various packages

10% to + 5%

10%

IH_X

and V

IL_X

XFD

) for

Document #: 38-08032 Rev. *K Page 60 of 60

Datasheet CY7C68013A Datasheet (CYPRESS)

Specifications and Main Features

Frequently Asked Questions

User Manual