Datasheet CS5257A-1GT5, CS5257A-1GDPR5, CS5257A-1GDP5 Datasheet (Cherry Semiconductor)

Page 1
V
SENSE
V
OUT
V
CONTROL
V
POWER
CS5257A-1
2.5V @ 7A
Load
124 1%
124 1%
0.1mF 5V
10mF 10V
3.3V
5.0V
Adjust
Features
Package Options
CS5257A-1
7A LDO 5-Pin Adjustable Linear Regulator
CS5257A-1
Description
Applications Diagram
5 Lead TO-220
1
1. V
SENSE
2. Adjust
3. V
OUT
4. V
CONTROL
5. V
POWER
Tab = V
OUT
1
Rev. 4/5/99
This new very low dropout regula­tor is designed to power the next generation of advanced micropro­cessors. To achieve very low dropout, the internal pass transistor is powered separately from the con­trol circuitry. Furthermore, with the control and power inputs tied together, this device can be used in single supply configuration and still offer a better dropout voltage than conventional PNP-NPN based LDO regulators. In this mode the dropout is determined by the mini­mum control voltage.
It is supplied in five-terminal TO-220 and D
2
PAK packages, allowing for the implementation of a remote-sense pin permitting very accurate regulation of output volt­age directly at the load, where it counts, rather than at the regulator. This remote sensing feature virtual­ly eliminates output voltage varia­tions due to load changes and resis­tive voltage drops. Typical load
regulation measured at the sense pin is 1mV for an output voltage of
2.5V with a load step of 10mA to 7A.
The very fast transient loop response easily meets the needs of the latest microprocessors. In addi­tion, a small capacitor on the Adjust pin will further improve the tran­sient capabilities.
Internal protection circuitry pro­vides for Òbust-proofÓ operation, similar to three-terminal regulators. This circuitry, which includes over­current, short circuit, supply sequencing and overtemperature protection will self protect the regu­lator under all fault conditions.
The CS5257A-1 is ideal for generat­ing a secondary 2-2.5V low voltage supply on a motherboard where both 5V and 3.3V are already avail­able.
1.25V to 5V V
OUT
at 7A
V
POWER
Dropout < 0.35V @ 7A
V
CONTROL
Dropout < 1.10V @
7A
1.5% Trimmed Reference
Fast Transient Response
Remote Voltage Sensing
Thermal Shutdown
Current Limit
Short Circuit Protection
Drop-In Replacement for
LT1580
Backwards Compatible with
3-pin Regulators
1
5 Lead D2PAK
Cherry Semiconductor Corporation
2000 South County Trail, East Greenwich, RI 02818
Tel: (401)885-3600 Fax: (401)885-5786
Email: info@cherry-semi.com
Web Site: www.cherry-semi.com
A Company
¨
Page 2
Electrical Characteristics:
0¡C ² TA² 70¡C, 0¡C ² TJ² 150¡C, V
SENSE
= V
OUT
and V
Adj
=
0V; unless otherwise specified.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
CS5257A-1
2
Absolute Maximum Ratings
V
POWER
Input Voltage .................................................................................................................................................................6V
V
CONTROL
Input Voltage ...........................................................................................................................................................13V
Operating Junction Temperature Range...........................................................................................................0¡C ² TJ² 150¡C
Storage Temperature Range................................................................................................................................-65¡C to +150¡C
Lead Temperature Soldering
Wave Solder (through hole styles only) .....................................................................................10 sec. max, 260¡C peak
Reflow (SMD styles only) ......................................................................................60 sec. max above 183¡C, 230¡C peak
ESD Damage Threshold............................................................................................................................................................2kV
Reference Voltage V
CONTROL
= 2.75V to 12V, V
POWER
= 2.05V to 5.5V, 1.234 1.253 1.272 V
10mA ² I
OUT
² 7A (-1.5%) (+1.5%)
Line Regulation V
CONTROL
= 2.5V to 12V, V
POWER
= 1.75V to 5.5V, .02 .20 %
I
OUT
= 10mA
Load Regulation V
CONTROL
= 2.75V, V
POWER
= 2.05V, .04 .20 %
(Note 3) I
OUT
= 10mA to 7A, with remote sense
Minimum Load Current V
CONTROL
= 5V, V
POWER
= 3.3V, ÆV
OUT
= +1% 5 10 mA
(Note 1)
Control Pin Current V
CONTROL
= 2.75V, V
POWER
= 2.05V, I
OUT
= 100mA 6 10 mA
(Note 2) V
CONTROL
= 2.75V, V
POWER
= 2.05V, I
OUT
= 4A 30 60 mA
V
CONTROL
= 2.75V, V
POWER
= 1.75V, I
OUT
= 4A 33 70 mA
V
CONTROL
= 2.75V, V
POWER
= 2.05V, I
OUT
= 7A 60 180 mA
Adjust Pin Current V
CONTROL
= 2.75V, V
POWER
= 2.05V, I
OUT
= 10mA 60 120 µA
Current Limit V
CONTROL
= 2.75V, V
POWER
= 2.05V, ÆV
OUT
= -1.5% 7.1 10.0 A
Short Circuit Current V
CONTROL
= 2.75V, V
POWER
= 2.05V, V
OUT
= 0V 5.0 9.0 A
Ripple Rejection V
CONTROL
= V
POWER
= 3.25V, 60 80 dB
(Note 3) V
RIPPLE
= 1V
P-P
@ 120Hz, I
OUT
= 4A, C
ADJ
= 0.1µF
Thermal Regulation 30ms Pulse, TA = 25¡C 0.002 %/W
V
CONTROL
Dropout Voltage V
POWER
= 2.05V, I
OUT
= 100mA 1.00 1.15 V
(Minimum V
CONTROL-VOUT
)V
POWER
= 2.05V, I
OUT
= 1A 1.00 1.15 V
(Note 4) V
POWER
= 2.05V, I
OUT
= 2.75A 1.00 1.15 V
V
POWER
= 2.05V, I
OUT
= 4A 1.00 1.15 V
V
POWER
= 2.05V, I
OUT
= 7A 1.10 1.25 V
V
POWER
Dropout Voltage V
CONTROL
= 2.75V, I
OUT
= 100mA .10 .15 V
(Minimum V
POWER-VOUT
)V
CONTROL
= 2.75V, I
OUT
= 1A .15 .20 V
(Note 4) V
CONTROL
= 2.75V, I
OUT
= 2.75A .20 .30 V
V
CONTROL
= 2.75V, I
OUT
= 4A .26 .40 V
V
CONTROL
= 2.75V, I
OUT
= 7A .35 .65 V
RMS Output Noise Freq = 10Hz to 10kHz, TA = 25¡C 0.003 %V
OUT
Temperature Stability 0.5 %
Thermal Shutdown (Note 5) 150 180 210 ¡C
Thermal Shutdown Hysteresis 25 ¡C
V
CONTROL
Supply Only V
CONTROL
= 13V, V
POWER
not connected, 50 mA
Output Current V
ADJUST
= V
OUT
= V
SENSE
= 0V
Page 3
CS5257A-1
Package Pin Description
PACKAGE PIN # PIN SYMBOL FUNCTION
3
Block Diagram
Electrical Characteristics:
0¡C ² TA² 70¡C, 0¡C ² TJ² 150¡C, V
SENSE
= V
OUT
and V
Adj
=
0V unless otherwise specified.
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
V
POWER
Supply Only V
POWER
= 6V, V
CONTROL
not connected, 0.1 1 mA
Output Current V
ADJUST
= V
OUT
= V
SENSE
= 0V
Note 1: The minimum load current is the minimum current required to maintain regulation. Normally the current in the resistor divider used to set
the output voltage is selected to meet the minimum load current requirement.
Note 2: The V
CONTROL
pin current is the drive current required for the output transistor. This current will track output current with roughly a 1:100
ratio. The minimum value is equal to the quiescent current of the device. Note 3: This parameter is guaranteed by design and is not 100% production tested. Note 4: Dropout is defined as either the minimum control voltage, (V
CONTROL)
or minimum power voltage (V
POWER
) to output voltage differential
required to maintain 1.5% regulation at a particular load current. Note 5: This parameter is guaranteed by design, but not parametrically tested in production. However, a 100% thermal shutdown functional test is
performed on each part.
5L TO-220
1V
SENSE
This Kelvin sense pin allows for remote sensing of the output voltage at the load for improved regulation. It is internally connected to the positive input of the voltage sensing error amplifier.
2 Adjust This pin is connected to the low side of the internally trimmed 1.5% bandgap
reference voltage and carries a bias current of about 50µA. A resistor divider from Adj to V
OUT
and from Adj to ground sets the output voltage. Also, transient response can be improved by adding a small bypass capacitor from this pin to ground.
3V
OUT
This pin is connected to the emitter of the power pass transistor and pro­vides a regulated voltage capable of sourcing 7A of current.
4V
CONTROL
This is the supply voltage for the regulator control circuitry. For the device to regulate, this voltage should be between 1V and 1.25V (depending on the output current) greater than the output voltage. The control pin current will be about 1% of the output current.
5V
POWER
This is the power input voltage. The pin is physically connected to the collec­tor of the power pass transistor. For the device to regulate, this voltage should be between 0.1V and 0.65V greater than the output voltage, depend­ing on output current. The output load current of 7A is supplied through this pin.
V
POWER
V
CONTROL
BIAS
and
TSD
V
REF
-
EA
+
IA
+
-
V
OUT
V
SENSE
Adjust
Page 4
CS5257A-1
4
Typical Performance Characteristics
0 10 20 30 40 50 60 70 80 90 100 110120130
-0.150
-0.125
-0.100
-0.075
-0.050
-0.025
-0.000
0.025
0.050
0.075
0.100
T
J
(°C)
Output Voltage Deviation (%)
I0=10mA V
CONTROL
=2.75V,
V
POWER
=2.05V
Reference Voltage vs Temperature
50
0
-50
-100
7
0
02 5
0
Time (ms)
Output Voltage Deviation (mV)Current (A)
100
134
COUT=330mF CPOWER=110mF C
CONTROL=10mF
CADJUST=0.1mF VCONTROL=5V V
POWER=3.3V
VOUT=2.5V
Transient Response
0.0 0.5
0.0
15.0
Output Current (A)
V
POWER-VOUT
(V)
1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
14.0
13.0
12.0
6.0
5.0
4.0
3.0
2.0
1.0
11.0
10.0
7.0
8.0
9.0
V
CONTROL
=2.75V
Short Circuit Current vs V
POWER-VOUT
0.0
83.0
Adjust Pin Current (mA)
Temperature (C)
40.0 60.0 80.0 100.0
81.0
79.0
77.0
75.0
73.0
71.0
69.0
67.0
65.0
20.0 120.0
160.0140.0
Adjust Pin Current vs Temperature
1.0 3.0 4.0 5.0 6.0 7.0
800.000
Minimum Load Current (mA)
V
CONTROL-VOUT
(V)
9.0 10.0 11.02.0 8.0
850.000
900.000
950.000
1000.000
1050.000
1100.000
1150.000
1200.000
VPOWER =3.3V D VOUT=+1%
Minimum Load Current vs V
CONTROL-VOUT
3.002.000.00
0.000
0.060
0.070
0.080
0.090
0.100
Output Current (A)
Output Voltage Deviation (%)
1.00
4.00
6.005.00
7.00
0.010
0.020
0.050
0.040
0.030
V
POWER
=2.05V
V
CONTROL
=2.75V
Load Regulation vs Output Current
Page 5
CS5257A-1
5
Typical Performance Characteristics: continued
10.0
10
1
Frequency (Hz)
Ripple Rejection (dB)
20.0
30.0
40.00
60.0
70.0
80.0
90.0
10
2
10
3
10
4
10
6
10
5
50.0
VIN-V
OUT
=2V
I
OUT
=4A
V
RIPPLE
=1V
P-P
C
OUT
=22mF
C
ADJ
=0.1mF
Ripple Rejection vs Frequency
1.0 3.0 4.0 5.0 6.0 7.0
70.00
Adjust Pin Current (mA)
V
CONTROL-VOUT
(V)
9.0
71.00
72.00
73.00
74.00
75.00
10.0 11.02.0 8.0
VPOWER =2.05V IL=10mA
Adjust Pin Current vs V
CONTROL-VOUT
0.00
0.000
1.000
V
POWER
Dropout Voltage (V)
Output Current (A)
1.00 2.00 3.00 4.00 5.00 6.00 7.00
0.900
0.800
0.700
0.600
0.500
0.400
0.300
0.200
0.100
V
CONTROL
=2.75V
V
POWER
Dropout Voltage vs I
OUT
0.50
70.00
Adjust Pin Current (mA)
V
POWER-VOUT
(V)
2.50
71.00
72.00
73.00
74.00
75.00
3.50 4.501.50
VCONTROL=2.75V IL=10mA
3.002.000.00
0.00
0.250
0.500
0.750
1.000
1.250
Output Current (A)
V
CONTROL
Drop Out Voltage (V)
V
POWER
=2.05V
1.00
4.00
6.005.00
7.00
V
CONTROL
Dropout Voltage vs I
OUT
Adjust Pin Current vs V
POWER -VOUT
0.50 1.50 2.50
915.500
Minimum Load Current (mA)
V
POWER-VOUT
(V)
3.50 4.50
915.600
915.700
915.800
915.900
916.000
916.100
916.200
916.400
VCONTROL =5V D VOUT=+1%
915.400
916.300
Minimum Load Current vs V
POWER-VOUT
Page 6
CS5257A-1
6
Application Notes
Typical Performance Characteristics: continued
74.00
76.00
77.00
0.00 1.00 5.00 7.00
Output Current (A)
Adjust Pin Current (mA)
75.00
73.00
72.00
6.002.00 3.00 4.00 8.00
V
POWER
=2.05
V
CONTROL
=2.75V
Adjust Pin Current vs Output Current
The CS5257A-1 linear regulator provides adjustable volt­ages from 1.25V to 5V at currents up to 7A. The regulator is protected against short circuits, and includes a thermal shutdown circuit with hysteresis. The output, which is cur­rent limited, consists of a PNP-NPN transistor pair and requires an output capacitor for stability. A detailed pro­cedure for selecting this capacitor is included in the Stability Considerations section.
V
POWER
Function
The CS5257A-1 utilizes a two supply approach to maxi­mize efficiency. The collector of the power device is brought out to the V
POWER
pin to minimize internal power
dissipation under high current loads. V
CONTROL
provides power for the control circuitry and the drive for the output NPN transistor. V
CONTROL
should be at least 1V greater than the output voltage. Special care has been taken to ensure that there are no supply sequencing problems. The output voltage will not turn on until both supplies are operating. If the control voltage comes up first, the output current will be typically limited to about 3mA until the power input voltage comes up. If the power input voltage comes up first the output will not turn on at all until the control voltage comes up. The output can never come up unregulated.
The CS5257A-1 can also be used as a single supply device with the control and power inputs tied together. In this mode, the dropout will be determined by the minimum control voltage.
Output Voltage Sensing
The CS5257A-1 five terminal linear regulator includes a dedicated V
SENSE
function. This allows for true Kelvin sensing of the output voltage. This feature can virtually eliminate errors in the output voltage due to load regula­tion. Regulation will be optimized at the point where the sense pin is tied to the output.
Adjustable Operation
This LDO adjustable regulator has an output voltage range of 1.25V to 5V. An external resistor divider sets the output voltage as shown in Figure 1. The regulatorÕs voltage sens­ing error amplifier maintains a fixed 1.253V reference between the output pin and the adjust pin.
A resistor divider network R1and R2causes a fixed current to flow to ground. This current creates a voltage across R
2
that adds to the 1.253V across R1and sets the overall out­put voltage. The adjust pin current (typically 50µA) also flows through R2and adds a small error that should be taken into account if precise adjustment of V
OUT
is neces-
sary. The output voltage is set according to the formula:
V
OUT
= 1.253V ´ + R2 ´ I
ADJ
The term I
ADJ
´ R2represents the error added by the adjust pin current. R1is chosen so that the minimum load current is a least 10mA. R1and R2should be of the same composi­tion for best tracking over temperature. The divider resis­tors should be placed physically as close to the load as pos­sible.
Figure 1: An external resistor divider sets the value of V
OUT
. The 1.253V
reference voltage drops across R1.
R1+R
2
R
1
Design GuidelinesTheory of Operation
CS5257A-1
V
Adjust
V
OUT
SENSE
R1
V
CONTROL
V
POWER
R2
Page 7
CS5257A-1
7
Application Notes: continued
While not required, a bypass capacitor connected between the adjust pin and ground will improve transient response and ripple rejection. A 0.1µF tantalum capacitor is recom­mended for Òfirst cutÓ design. Value and type may be var­ied to optimize performance vs. price.
Other Adjustable Operation Considerations
The CS5257A-1 linear regulator has an absolute maximum specification of 6V for the voltage difference between V
IN
and V
OUT
. However, the IC may be used to regulate volt­ages in excess of 6V. The two main considerations in such a design are the sequencing of power supplies and short cir­cuit capability.
Power supply sequencing should be such that the V
CON-
TROL
supply is brought up coincidentally with or before the
V
POWER
supply. This allows the IC to begin charging the
output capacitor as soon as the V
POWER
to V
OUT
differential
is large enough that the pass transistor conducts. As V
POW-
ER
increases, the pass transistor will remain in dropout, and
current is passed to the load until V
OUT
is in regulation. Further increase in the supply voltage brings the pass tran­sistor out of dropout. In this manner, any output voltage less than 13V may be regulated, provided the V
POWER
to
V
OUT
differential is less than 6V. In the case where V
CON-
TROL
and V
POWER
are shorted, there is no theoretical limit
to the regulated voltage as long as the V
POWER
to V
OUT
dif-
ferential of 6V is not exceeded. There is a possibility of damaging the IC when V
POWER-VIN
is greater than 6V if a short circuit occurs. Short circuit con­ditions will result in the immediate operation of the pass transistor outside of its safe operating area. Over-voltage stresses will then cause destruction of the pass transistor before overcurrent or thermal shutdown circuitry can become active. Additional circuitry may be required to clamp the V
POWER
to V
OUT
differential to less than 6V if fail safe operation is required. One possible clamp circuit is illustrated in Figure 2; however, the design of clamp cir­cuitry must be done on an application by application basis. Care must be taken to ensure the clamp actually protects the design. Components used in the clamp design must be able to withstand the short circuit condition indefinitely while protecting the IC.
Figure 2: Example clamp circuitry for V
POWER
- V
OUT
> 6V.
Stability Considerations
The output compensation capacitor helps determine three main characteristics of a linear regulator: start-up delay, load transient response, and loop stability.
The capacitor value and type is based on cost, availability, size and temperature constraints. A tantalum or aluminum electrolytic capacitor is best, since a film or ceramic capaci­tor with almost zero ESR can cause instability. The alu­minum electrolytic capacitor is the least expensive solution. However, when the circuit operates at low temperatures, both the value and ESR of the capacitor will vary consider­ably. The capacitor manufacturer's data sheet provides this information.
A 300µF tantalum capacitor will work for most applica­tions, but with high current regulators such as the CS5257A-1 the transient response and stability improve with higher values of capacitor. The majority of applica­tions for this regulator involve large changes in load cur­rent so the output capacitor must supply the instantaneous load current. The ESR of the output capacitor causes an immediate drop in output voltage given by:
ÆV = ÆI ´ ESR.
For microprocessor applications it is customary to use an output capacitor network consisting of several tantalum and ceramic capacitors in parallel. This reduces the overall ESR and reduces the instantaneous output voltage drop under transient load conditions. The output capacitor net­work should be as close to the load as possible for the best results.
Protection Diodes
When large external capacitors are used with a linear regulator it is sometimes necessary to add protection diodes. If the input voltage of the regulator gets shorted, the output capacitor will discharge into the output of the regulator. The discharge current depends on the value of the capacitor, the output voltage, and the rate at which V
CONTROL
drops. In the CS5257A-1 regulator, the discharge path is through a large junction and protection diodes are not usually needed. If the regulator is used with large val­ues of output capacitance and the input voltage is instanta­neously shorted to ground, damage can occur. In this case, a diode connected as shown in Figure 3 is recommended.
Use of the diode has the added benefit of bleeding V
OUT
to
ground if V
CONTROL
is shorted. This prevents an unregulat-
ed output from causing system damage.
Figure 3: Diode protection against V
CONTROL
short circuit conditions.
External Supply
V
Control
V
Power
V
Adjust
V
SENSE
V
OUT
Adjust
V
V
SENSE
OUT
V
CONTROL
CS5257A-1
V
POWER
Page 8
8
CS5257A-1
Application Notes: continued
A rule of thumb useful in determining if a protection diode is required is to solve for current
I= C
´ V , where
T
I is the current flow out of the load capacitance
when V
CONTROL
is shorted, C is the value of load capacitance V is the output voltage, and T is the time duration required for V
CONTROL
to transition from high to being shorted.
If the calculated current is greater than or equal to the typi­cal short circuit current value provided in the specifica­tions, serious thought should be given to the use of a pro­tection diode.
Current Limit
The internal current limit circuit limits the output current under excessive load conditions.
Short Circuit Protection
The device includes short circuit protection circuitry that clamps the output current at approximately two amperes less than its current limit value. This provides for a current foldback function, which reduces power dissipation under a direct shorted load.
Thermal Shutdown
The thermal shutdown circuitry is guaranteed by design to activate above a die junction temperature of approximately 150¡C and to shut down the regulator output. This circuit­ry has 25¡C of typical hysteresis, thereby allowing the reg­ulator to recover from a thermal fault automatically.
Calculating Power Dissipation and Heat Sink Requirements
High power regulators such as the CS5257A-1 usually operate at high junction temperatures. Therefore, it is important to calculate the power dissipation and junction temperatures accurately to ensure that an adequate heat sink is used. Since the package tab is connected to Vout on the CS5257A-1, electrical isolation may be required for some applications. Also, as with all high power packages, thermal compound in necessary to ensure proper heat flow. For added safety, this high current LDO includes an internal thermal shutdown circuit
The thermal characteristics of an IC depend on the follow­ing four factors: junction temperature, ambient tempera­ture, die power dissipation, and the thermal resistance from the die junction to ambient air. The maximum junc­tion temperature can be determined by:
T
J(max)
= T
A(max)
+ PD
(max)
´ R
QJA
The maximum ambient temperature and the power dissi­pation are determined by the design while the maximum junction temperature and the thermal resistance depend on the manufacturer and the package type. The maximum power dissipation for a regulator is:
PD
(max)
= (V
IN(max)-VOUT(min))IOUT(max)
+ V
IN(max)
´ I
IN(max)
A heat sink effectively increases the surface area of the package to improve the flow of heat away from the IC and into the surrounding air. Each material in the heat flow path between the IC and the outside environment has a thermal resistance which is measured in degrees per watt. Like series electrical resistances, these thermal resistances are summed to determine the total thermal resistance between the die junction and the surrounding air, R
QJA
. This total thermal resistance is comprised of three compo­nents. These resistive terms are measured from junction to case (R
QJC
), case to heat sink (R
QCS
), and heat sink to ambi-
ent air (R
QSA
). The equation is:
R
QJA
= R
QJC
+ R
QCS
+ R
QSA
The value for R
QJC
is 1.4ûC/watt for the CS5257A-1 in both the TO-220 and D2PAK packages. For a high current regu­lator such as the CS5257A-1 the majority of heat is generat­ed in the power transistor section. The value for R
QSA
depends on the heat sink type, while the R
QCS
depends on factors such as package type, heat sink interface (is an insulator and thermal grease used?), and the contact area between the heat sink and the package. Once these calcula­tions are complete, the maximum permissible value of R
QJA
can be calculated and the proper heat sink selected. For further discussion on heat sink selection, see our Cherry application note ÒThermal Management for Linear Regulators.Ó
Page 9
9
Rev. 4/5/99
Thermal Data 5L 5L
TO-220 D2PAK
R
QJC
typ 1.4 1.4 ûC/W
R
QJA
typ 50 10-50* ûC/W
*Depending on thermal properties of substrate. R
qJA
= R
qJC
+ R
qCA
Package Specification
PACKAGE THERMAL DATA
Ordering Information
Part Number Description
CS5257A-1GT5 5L TO-220 Straight CS5257A-1GDP5 5L D2PAK CS5257A-1GDPR5 5L D2PAK (tape & reel)
© 1999 Cherry Semiconductor Corporation
CS5257A-1
Cherry Semiconductor Corporation reserves the right to make changes to the specifications without notice. Please contact Cherry Semiconductor Corporation for the latest available information.
PACKAGE DIMENSIONS IN mm (INCHES)
5 Lead D2PAK (DP)
1.70 (.067) REF
0.10 (.004)
0.00 (.000)
10.31 (.406)
10.05 (.396)
0.91 (.036)
0.66 (.026)
1.40 (.055)
1.14 (.045)
4.57 (.180)
4.31 (.170)
1.68 (.066)
1.40 (.055)
2.74(.108)
2.49(.098)
.254 (.010) REF
2.79 (.110)
2.29 (.090)
15.75 (.620)
14.73 (.580)
8.53 (.336)
8.28 (.326)
5 Lead TO-220 (T) Straight
2.87 (.113)
2.62 (.103)
6.93(.273)
6.68(.263)
9.78 (.385)
10.54 (.415)
1.02(.040)
0.63(.025)
1.83(.072)
1.57(.062)
0.56 (.022)
0.36 (.014)
2.92 (.115)
2.29 (.090)
1.40 (.055)
1.14 (.045)
4.83 (.190)
4.06 (.160)
6.55 (.258)
5.94 (.234)
14.22 (.560)
13.72 (.540)
1.02 (.040)
0.76 (.030)
3.71 (.146)
3.96 (.156)
14.99 (.590)
14.22 (.560)
Loading...