Datasheet CRCW series Specification

D/CRCW

Vishay

Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors

FEATURES

• Stability ΔR/R = 1 % for 1000 h at 70 °C

• Lead (Pb)-bearing termination plating on Ni barrier layer

• Metal glaze on high quality ceramic

• Halogen-free according to IEC 61249-2-21 definiton

• AEC-Q200 qualified, rev. C compliant

STANDARD ELECTRICAL SPECIFICATIONS

SIZE

MODEL

INCH METRIC

D10/CRCW0402 0402 RR 1005M

RATED DISSIPATION

P

70

W

0.063 50

Zero-Ohm-Resistor: R

D11/CRCW0603 0603 RR 1608M

0.10 75

Zero-Ohm-Resistor: R

D12/CRCW0805 0805 RR 2012M

0.125 150

Zero-Ohm-Resistor: R

D25/CRCW1206 1206 RR 3216M

0.25 200

Zero-Ohm-Resistor: R

CRCW1210 1210 RR 3225M

0.50 200

Zero-Ohm-Resistor: R

CRCW1218 1218 RR 3246M

1.0 200

Zero-Ohm-Resistor: R

CRCW2010 2010 RR 5025M

0.75 400

Zero-Ohm-Resistor: R

CRCW2512 2512 RR 6332M

1.0 500

Zero-Ohm-Resistor: R

Notes

• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over

operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.

• Marking: See datasheet “Surface Mount Resistor Marking” (document number 20020).

• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.

LIMITING

ELEMENT

VOLTAGE

U

AC/DC

max.

= 20 mΩ, I

max.

= 20 mΩ, I

max.

= 20 mΩ, I

max.

= 20 mΩ, I

max.

= 20 mΩ, I

max.

= 20 mΩ, I

max.

= 20 mΩ, I

max.

= 20 mΩ, I

max.

TEMPERATURE

COEFFICIENT

ppm/K

± 100
± 200

= 1.5 A

max.

± 100
± 200

= 2.0 A

max.

± 100
± 200

= 2.5 A

max.

± 100
± 200

= 3.5 A

max.

± 100
± 200

= 5.0 A

max.

± 100
± 200

= 7.0 A

max.

± 100
± 200

= 6.0 A

max.

± 100
± 200

= 7.0 A

max.

TOLERANCE

%

± 1
± 5

± 1
± 5

± 1
± 5

± 1
± 5

± 1
± 5

± 1
± 5

± 1
± 5

± 1
± 5

RESISTANCE

RANGE

Ω

1R0 to 10M

1R0 to 10M

1R0 to 10M

1R0 to 10M

1R0 to 10M

1R0 to 2M2

1R0 to 10M

1R0 to 10M

SERIES

E24; E96

E24

E24; E96

E24

E24; E96

E24

E24; E96

E24

E24; E96

E24

E24; E96

E24

E24; E96

E24

E24; E96

E24

www.vishay.com For technical questions, contact: [e-mail]

Document Number: 20008

118 Revision: 18-Nov-10

D/CRCW

Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors

Vishay

TECHNICAL SPECIFICATIONS

PARAMETER UNIT

Rated dissipation at 70 °C

Limiting element voltage

U

AC/DC

MAX.

Insulation voltage
(1 min)

Insulation resistance

Category temperature range °C - 55 to + 155

Failure rate h

Weight mg 0.65 2 5.5 10 16 29.5 25.5 40.5

Note

(1)

The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.

(1)

U

INS.

D10/

CRCW0402

W 0.063 0.1 0.125 0.25 0.5 1.0 0.75 1.0

V 50 75 150 200 200 200 400 500

V > 75 > 100 > 200 > 300 > 300 > 300 > 300 > 300

Ω

-1

D11/

CRCW0603

D12/

CRCW0805

D25/

CRCW1206

> 10

< 0.1 x 10

CRCW1210 CRCW1218 CRCW2010 CRCW2512

9

-9

PART NUMBER AND PRODUCT DESCRIPTION

Part Number: CRCW0805562RFKTA

C R C W 0 8 0 5 5 6 2 R F K T A

(2)

MODEL VALUE TOLERANCE TCR PACKAGING SPECIAL

CRCW0402
CRCW0603
CRCW0805
CRCW1206
CRCW1210
CRCW1218
CRCW2010
CRCW2512

Product Description: CRCW0805 100 562R 1 % RT1

CRCW0805 100 562R 1 % RT1

MODEL

CRCW0402
CRCW0603
CRCW0805
CRCW1206
CRCW1210
CRCW1218
CRCW2010
CRCW2512

R = Decimal

K = Thousand

M = Million

0000 = Jumper

TCR

± 100 ppm/K
± 200 ppm/K

F = ± 1 %
J = ± 5 %

Z = Jumper

RESISTANCE VALUE TOLERANCE

10R = 10 Ω

562R = 562 Ω

10K = 10.0 kΩ

1M = 1 MΩ

0R0 = Jumper

K = ± 100 ppm/K
N = ± 200 ppm/K

S = Jumper or

special

± 1 %
± 5 %

TA
TB
TC
TD
TE
TF
TG
TH
TK

Up to 2 digits

PA CK A GI N G

RT1
RT5
RT6
RT7
RF4
R02
R67
R82
RT9

Note

(2)

Preferred way for ordering products is by use of the PART NUMBER.

Document Number: 20008 For technical questions, contact: [e-mail]
Revision: 18-Nov-10 119

www.vishay.com

D/CRCW

Vishay

Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors

PACKAGING

PAPER TAPE

MODEL UNIT

QUANTITY PART NUMBER PRODUCT DESC. QUANTITY PART NUMBER PRODUCT DESC.

D10/CRCW0402

D11/CRCW0603

D12/CRCW0805

D25/CRCW1206

CRCW1210

CRCW1218 180 mm/7" 4000 TK RT9

CRCW2010 180 mm/7" 4000 TF R02

CRCW2512 180 mm/7"

180 mm/7" 10 000 TD RT7

330 mm/13" 50 000 TE RF4

180 mm/7" 5000 TA RT1

285 mm/11.25" 10 000 TB RT5

330 mm/13" 20 000 TC RT6

180 mm/7" 5000 TA RT1

285 mm/11.25" 10 000 TB RT5

330 mm/13" 20 000 TC RT6

180 mm/7" 5000 TA RT1

285 mm/11.25" 10 000 TB RT5

330 mm/13" 20 000 TC RT6

180 mm/7" 5000 TA RT1

285 mm/11.25" 10 000 TB RT5

330 mm/13" 20 000 TC RT6

ACC. IEC 60286-3, TYPE I

2000 TG R67

4000 TH R82

BLISTER TAPE

ACC. IEC 60286-3, TYPE II

DIMENSIONS

SIZE DIMENSIONS in millimeters

INCH METRIC L W H T1 T2

0402 1005 1.0 ± 0.05 0.5 ± 0.05 0.35 ± 0.05 0.25 ± 0.05 0.2 ± 0.1 0.4 0.6 0.5

0603 1608 1.55

0805 2012 2.0

1206 3216 3.2

1210 3225 3.2 ± 0.2 2.5 ± 0.2 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 2.5 2.0 1.1 2.5 2.2

1218 3246 3.2

2010 5025 5.0 ± 0.15 2.5 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 2.5 3.9 1.2 2.5 3.9

2512 6332 6.3 ± 0.2 3.15 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 3.2 5.2 1.2 3.2 5.2

+ 0.10

0.85 ± 0.1 0.45 ± 0.05 0.3 ± 0.2 0.3 ± 0.2 0.5 0.9 1.0 0.9 0.9 1.0

- 0.05

+ 0.20

1.25 ± 0.15 0.45 ± 0.05 0.3

- 0.10

+ 0.10

1.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 1.7 2.0 1.1 1.7 2.3

- 0.20

+ 0.10

4.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 1.05 4.9 1.9 1.25 4.8 1.9

- 0.20

+ 0.20

0.3 ± 0.2 0.7 1.3 1.2 0.9 1.3 1.3

- 0.10

SOLDER PAD DIMENSIONS in millimeters

REFLOW SOLDERING

abl abl

WAVE SOLDERING

www.vishay.com For technical questions, contact: [e-mail] Document Number: 20008
120 Revision: 18-Nov-10

D/CRCW

1000

100

10

1

0.1

0.01

Single Pulse

Pulse Load

max.

(W)

P

2512
1218
2010
1210
1206
0805
0603
0402

10

-6

Pulse Duration i (s)

t

10

-5

10

-4

10

-3

10-210

-1

1 10 100

Maximum pulse load, single pulse; applicable if P 0 and n < 1000 and Û ≤ Û

max.

;

for permissible resistance change equivalent to 8000 h operation

1000

10

1

0.1

0.01
10

-6

Continuous Pulse

Maximum pulse load, continuous pulses; applicable if P ≤ P (ϑ

amb

) and Û ≤ Û

max.

;

for permissible resistance change equivalent to 8000 h operation

Pulse Duration i (s)

Continuous Pulse Load

max.

(W)

t

P

100

10

-5

10

-4

10

-3

10-210

-1

1 10 100

2512
1218
2010
1210
1206
0805
0603
0402

Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors

FUNCTIONAL PERFORMANCE

Vishay

Document Number: 20008 For technical questions, contact: [e-mail]
Revision: 18-Nov-10 121

Pulse Voltage

2000

(V)

max.

Û

Pulse Voltage

2512

1800

1600

2010

1400

1200

1000

1206/1210/1218

800

600

0805

400

200

0402

0

- 6

10

0603

- 5

10

Maximum pulse voltage, single and continuous pulses; applicable if

P ≤ P

max.

- 4

10

; for permissible resistance change equivalent to 8000 h operation

10

- 3

10

- 2

- 1

10

Pulse Duration i (s)

110

t

www.vishay.com

D/CRCW

100 1K 10K 100K 1M 10M

100

10

1

0.1

0.01

Current Noise A

1

in µV/V

Current Noise

2010

1206

0805

0603

0402

Resistance Value R in Ω

Vishay

Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors

Derating

120

100

80

60

40

Fraction of Rated Dissipation in %

20

0

- 55 - 25 0 25 50 75 100 125 155 175

Non-Linearity

120

Ambient Temperature in °C

70

100

80

60

40

20

Attenuation of 3rd Harmonic A3 in dB

1206, 2010
0805

0603
0402

0

10

100 1K 10K 100K 1M 10M

Resistance Value R in Ω

www.vishay.com For technical questions, contact: [e-mail] Document Number: 20008
122 Revision: 18-Nov-10

D/CRCW

P70 x R

P70 x R

Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors

Vishay

TEST PROCEDURES AND REQUIREMENTS

REQUIREMENTS PERMISSIBLE

EN
60115-1
CLAUSE

4.5 - Resistance - ± 1 % ± 5 %

4.7 - Voltage proof U = 1.4 · U

4.13 - Short time overload

4.17.2 58 (Td) Solderability

4.8.4.2 - Temperature coefficient

4.32 21 (Uu

4.33 21 (Uu

4.19 14 (Na) Rapid change of temperature

4.23 - Climatic sequence: -

4.23.2 2 (Ba) Dry heat 125 °C; 16 h

4.23.3 30 (Db) Damp heat, cyclic

4.23.4 1 (Aa) Cold - 55 °C; 2 h

4.23.5 13 (M) Low air pressure 1 kPa; (25 ± 10) °C; 1 h

4.23.6 30 (Db) Damp heat, cyclic

4.23.7 - DC load U =

4.25.1 - Endurance at 70 °C

4.18.2 58 (Td) Resistance to soldering heat

4.35 - Flamability, needle flame test

4.24 78 (Cab) Damp heat, steady state

4.25.3 -

4.40 -

4.29 45 (XA) Component solvent resistance

4.30 45 (XA) Solvent resistance of marking

Document Number: 20008 For technical questions, contact: [e-mail]
Revision: 18-Nov-10 123

IEC

60082-2

TEST

METHOD

3)

1)

TEST

Stability for product types:

U = 2.5 x ≤ 2 x U

Solder bath method; Sn60Pb40;

Shear (adhesion)

Substrate bending Depth 2 mm; 3 times

Endurance at upper

category temperature

Electrostatic discharge

(human body model)

PROCEDURE

D/CRCW

60 s No flashover or breakdown

ins;

duration: Acc. to style

non-activated flux;

(235 ± 5) °C, (2 ± 0.2) s

(20/- 55/20) °C and

(20/125/20) °C

RR 1608 and smaller: 9 N
RR 2012 and larger: 45 N

30 min. at - 55 °C;

30 min. at 125°C

5 cycles

1000 cycles

55 °C; ≥ 90 % RH;

24 h; 1 cycle

55 °C; ≥ 90 % RH;

24 h; 5 cycles

U = √(P

(260 ± 5) °C; (10 ± 1) s

(93 ± 3) % RH; 56 days

3 pos. + 3 neg. discharges;

ESD test voltage acc. to size

50 °C; method 1, toothbrush

x R) ≤ U

70

1.5 h on; 0.5 h off;
70 °C; 1000 h
70 °C; 8000 h

Solder bath method

IEC 60695-11-5;

10 s

(40 ± 2) °C;

155 °C; 1000 h ± (1 % R + 0.05 Ω)± (2 % R + 0.1 Ω)

IEC 61340-3-1;

Isopropyl alcohol;

50 °C; method 2

Isopropyl alcohol;

max.

STABILITY CLASS 1

OR BETTER

1 Ω to 10 MΩ 1 Ω to 10 MΩ

;

max.

± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω)

Good tinning (≥ 95 %

covered);

no visible damage

± 100 ppm/K ± 200 ppm/K

± (0.25 % R + 0.05 Ω)

± (1 % R + 0.05 Ω)

± (1 % R + 0.05 Ω)± (2 % R + 0.1 Ω)

± (1 % R + 0.05 Ω)

± (2 % R + 0.1 Ω)

± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω)

CHANGE (ΔR)

STABILITY CLASS 2

OR BETTER

No visible damage

No visible damage,

no open circuit in bent position

± (0.25 % R + 0.05 Ω)

± (0.5 % R + 0.05 Ω)

± (1 % R + 0.05 Ω)

± (2 % R + 0.1 Ω)
± (4 % R + 0.1 Ω)

No burning after 30 s

± (1 % R + 0.05 Ω)

± (1 % R + 0.05 Ω)

No visible damage

Marking legible,

no visible damage

www.vishay.com

D/CRCW

15 x P70 x R

P70 x R

Vishay

Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors

TEST PROCEDURES AND REQUIREMENTS

EN
60115-1
CLAUSE

4.22 6 (Fc)

4.37 - Periodic electric overload

4.27 -

IEC

60082-2

TEST

METHOD

TEST

Vibration, endurance by

sweeping

Single pulse high voltage

overload, 10 µs/700 µs

Stability for product types:

U = ≤ 2 x U

Û = 10 x ≤ 2 x U

All tests are carried out in accordance with the following specifications:

• EN 60115-1, generic specification

• EN 140400, sectional specification

• EN 140401-802, detail specification

• IEC 60068-2, environmental test procedures

Packaging of components is done in paper or blister tapes according to IEC 60286-3.

PROCEDURE

D/CRCW

f = 10 Hz to 2000 Hz;

x, y, z ≤ 1.5 mm;

A ≤ 200 m/s

10 sweeps per axis

0.1 s on; 2.5 s off;
1000 cycles

10 pulses

2;

max.

max.

;

;

REQUIREMENTS PERMISSIBLE

CHANGE (ΔR)

STABILITY CLASS 1

OR BETTER

1 Ω to 10 MΩ 1 Ω to 10 MΩ

± (0.25 % R + 0.05 Ω) ± (0.5 % R + 0.05 Ω)

± (1 % R + 0.05 Ω)

± (1 % R + 0,05 Ω)

STABILITY CLASS 2

OR BETTER

www.vishay.com For technical questions, contact: [e-mail] Document Number: 20008
124 Revision: 18-Nov-10

Legal Disclaimer Notice

www.vishay.com

Vishay

Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Material Category Policy

Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.

Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.

Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.

Revision: 02-Oct-12

1

Document Number: 91000