Page 1
CRCW...BC e3
www.vishay.com
Vishay BCcomponents
Lead (Pb)-free Thick Film, Rectangular Commodity Chip Resistors
FEATURES
• High volume product suitable for commercial
applications
• Excellent stability (R/R 1 % for 1000 h at
70 °C)
• Lead (Pb)-free solder contacts on Ni barrier layer
• Metal glaze on high quality ceramic
• Protective overglaze
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
CRCW0402...BC 0402 RR 1005M
CRCW0603...BC 0603 RR 1608M
CRCW0805...BC 0805 RR 2012M
CRCW1206...BC 1206 RR 3216M
CRCW1210...BC 1210 RR 3225M
CRCW2010...BC 2010 RR 5025M
CRCW2512...BC 2512 RR 6332M
Notes
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
• Power rating depends on the maximum temperature at the solder point, the component placement density and the substrate material
CASE
SIZE
INCH
CASE
SIZE
METRIC
POWER RATING
P
70 °C
W
0.063 50
Zero-Ohm-Resistor: R
0.10 75
Zero-Ohm-Resistor: R
0.125 150
Zero-Ohm-Resistor: R
0.25 200
Zero-Ohm-Resistor: R
0.50 200
Zero-Ohm-Resistor: R
0.75 400
Zero-Ohm-Resistor: R
1.0 500
Zero-Ohm-Resistor: R
LIMITING
ELEMENT
VOLTAGE
MAX. V
max.
max.
max.
max.
max.
max.
max.
TEMPERATURE
COEFFICIENT
= 20 m, I
= 20 m, I
= 20 m, I
= 20 m, I
= 20 m, I
= 20 m, I
= 20 m, I
ppm/K
± 100
± 200
at 70 °C = 1.5 A
max.
± 100
± 200
at 70 °C = 2.0 A
max.
± 100
± 200
at 70 °C = 2.5 A
max.
± 100
± 200
at 70 °C = 3.5 A
max.
± 100
± 200
at 70 °C = 4.0 A
max.
± 100
± 200
at 70 °C = 5.0 A
max.
± 100
± 200
at 70 °C = 7.0 A
max.
TOLERANCE
%
± 1
± 5
± 1
± 5
± 1
± 5
± 1
± 5
± 1
± 5
± 1
± 5
± 1
± 5
RESISTANCE
RANGE
1R0 to 10M
1R0 to 10M
1R0 to 10M
1R0 to 10M
1R0 to 10M
1R0 to 10M
1R0 to 10M
E-SERIES
24 + 96
24
24 + 96
24
24 + 96
24
24 + 96
24
24 + 96
24
24 + 96
24
24 + 96
24
Revision: 20-Apr-12
For technical questions, contact: f3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
1
Document Number: 28743
Page 2
CRCW...BC e3
www.vishay.com
TECHNICAL SPECIFICATIONS
PARAMETER UNIT
Rated Dissipation
at 70 °C
Limiting Element Voltage
U
Insulation Voltage
U
Insulation Resistance > 10
Category Temperature
Range
Failure Rate h
Weight/1000 Pieces g 0.65 2 5.5 10 16 25.5 40.5
Note
(1)
(1)
AC/DC
max.
(1 min)
ins
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
CRCW0402...BC CRCW0603...BC CRCW0805...BC CRCW1206...BC CRCW1210...BC CRCW2010...BC CRCW2512...BC
W 0.063 0.10 0.125 0.25 0.50 0.75 1.0
V 50 75 150 200 200 400 500
V > 75 > 100 > 200 > 300 > 300 > 300 > 300
9
°C - 55 to + 155
-1
0.3 x 10
-9
Vishay BCcomponents
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: CRCW0603562RFKTCBC
C R C W 0 6 0 3 5 6 2 R F K T C B C
MODEL VALUE TOLERANCE TCR PACKAGING Special
CRCW0402
CRCW0603
CRCW0805
CRCW1206
CRCW1210
CRCW2010
CRCW2512
PRODUCT DESCRIPTION: CRCW0603-BC 100 562R 1 % RT6 e3
CRCW0603-BC 100 562R 1 % RT6 e3
MODEL TCR
CRCW0402-BC
CRCW0603-BC
CRCW0805-BC
CRCW1206-BC
CRCW1210-BC
CRCW2010-BC
CRCW2512-BC
R = Decimal
K = Thousand
M = Million
0000 = Jumper
± 200 ppm/K
± 100 ppm/K
F = ± 1.0 %
J = ± 5.0 %
Z = Jumper
RESISTANCE
VALUE
10R = 10
562R = 562
10K = 10.0 k
1M = 1 M
0R0 = Jumper
K = ± 100 ppm/K
N = ± 200 ppm/K
0 = Jumper
TOLERANCE
VALUE
± 5 %
± 1 %
TA, TB
TC, TD
TE, TF
TH, TI
PACKAGING LEAD (Pb)-FREE
RT1, RT2
RT5, RT6
RT7, RF4
R02, R82
Up to 2 digits
BC = Commodity
e3 = Pure tin
termination finish
Revision: 20-Apr-12
For technical questions, contact: f3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
2
Document Number: 28743
Page 3
CRCW...BC e3
www.vishay.com
PACKAGING
REEL
MODEL
TAPE WIDTH DIAMETER PITCH
180 mm/7"
CRCW0402…BC 8 mm
254 mm/10" 20 000 TI RT2
2 mm
330 mm/13" 50 000 TE RF4
180 mm/7"
CRCW0603…BC 8 mm
254 mm/10" 10 000 TB RT5
4 mm
330 mm/13" 20 000 TC RT6
180 mm/7"
CRCW0805…BC 8 mm
254 mm/10" 10 000 TB RT5
4 mm
330 mm/13" 20 000 TC RT6
180 mm/7"
CRCW1206…BC 8 mm
254 mm/10" 10 000 TB RT5
4 mm
330 mm/13" 20 000 TC RT6
180 mm/7"
CRCW1210…BC 8 mm
254 mm/10" 10 000 TB RT5
4 mm
330 mm/13" 20 000 TC RT6
CRCW2010…BC 12 mm 180 mm/7" 4 mm 4000 TF R02
CRCW2512…BC 12 mm 180 mm/7" 4 mm 4000 TH R82
PIECES/
REEL
PART NUMBER PRODUCT DESC.
PAPER BLISTER PAPER BLISTER
10 000 TD RT7
5000 TA RT1
5000 TA RT1
5000 TA RT1
5000 TA RT1
Vishay BCcomponents
PACKAGING CODE
DIMENSIONS in millimeters
SIZE DIMENSIONS
REFLOW SOLDERING WAVE SOLDERING
SOLDER PAD DIMENSIONS
INCH METRIC L W H T1 T2 a b l a b l
0402 1005 1.0 ± 0.05 0.5 ± 0.05 0.35 ± 0.05 0.25 ± 0.05 0.2 ± 0.1 0.4 0.6 0.5
0603 1608 1.55
0805 2012 2.0
1206 3216 3.2
+ 0.10
0.85 ± 0.1 0.45 ± 0.05 0.3 ± 0.2 0.3 ± 0.2 0.5 0.9 1.0 0.9 0.9 1.0
- 0.05
+ 0.20
1.25 ± 0.15 0.45 ± 0.05 0.3
- 0.10
+ 0.10
1.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 1.7 2.0 1.1 1.7 2.3
- 0.20
+ 0.20
0.3 ± 0.2 0.7 1.3 1.2 0.9 1.3 1.3
- 0.10
1210 3225 3.2 ± 0.2 2.5 ± 0.2 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 2.5 2.0 1.1 2.5 2.2
2010 5025 5.0 ± 0.15 2.5 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 2.5 3.9 1.2 2.5 3.9
2512 6332 6.3 ± 0.2 3.15 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 3.2 5.2 1.2 3.2 5.2
Note
(1)
The rated dissipation applies only if the permitted film temperature is not exceeded. Furthermore, a high level of ambient temperature or of
power dissipation may raise the temperature of the solder joint, hence special solder alloys or boardmaterials maybe required to maintain
the reliability of the assembly. Specified power rating above 125 °C requires dedicated heat-sink pads, which depend on boardmaterials.
The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g. in standards IEC 61188-5-x, or
in publication IPC-7351. They do not guarantee any supposed thermal properties, particularly as these are also strongly influenced by many
other parameters. Still the given solder pad dimensions will be found adequate for most general applications.
(1)
Revision: 20-Apr-12
3
Document Number: 28743
For technical questions, contact: f3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Page 4
DERATING
- 55 - 25 0 25 50 75 100 125 155 175
120
100
80
60
40
20
0
70
Ambient Temperature in °C
Rated Power in %
P70 x R
CRCW...BC e3
www.vishay.com
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
4.5 - Resistance - ± 1 % ± 5 %
4.8.4.2 -
4.13 -
4.17.5 58 (Td) Solderability
4.18.2 58 (Td)
4.19 14 (Na)
4.24 78 (Cab)
IEC
60068-2
TEST
METHOD
TEST PROCEDURE
Stability for product types:
Temperature
coefficient
Short time
overload
Pre-aging
4 h at 155 °C,
Resistance to
soldering heat
Rapid change
of temperature
Damp heat,
steady state
(20/- 55/20) °C and
(20/125/20) °C
U = 2.5 x 2 x U
duration: Acc. to the style
dryheat
Solder bath method
(260 ± 5) °C;
(10 ± 1) s
30 min. at - 55 °C;
30 min. at 125 °C;
5 cycles
(40 ± 2) °C;
56 days;
(93 ± 3) % RH
CRCW....BC e3 1 to 10 M 1 to 10 M
max.;
Solder bath method;
Sn60Pb40
non activated flux;
(235 ± 5) °C
(2 ± 0.2) s
Solder bath method;
Sn96.5Ag3Cu0.5
non activated flux;
(245 ± 5) °C
(3 ± 0.3) s
REQUIREMENTS PERMISSIBLE CHANGE (R)
± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 )
± (1 % R + 0.05 )± (2 % R + 0.1 )
Vishay BCcomponents
STABILITY
CLASS 1
OR BETTER
± 100 ppm/K ± 200 ppm/K
Good tinning ( 95 % covered)
no visible damage
Good tinning ( 95 % covered)
no visible damage
STABILITY
CLASS 2
OR BETTER
Revision: 20-Apr-12
For technical questions, contact: f3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
4
Document Number: 28743
Page 5
www.vishay.com
P70 x R
P70 x R
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1
CLAUSE
4.23 -
4.23.2 2 (Ba) Dry heat 125 °C; 16 h
4.23.3 30 (Db)
4.23.4 1 (Aa) Cold - 55 °C; 2 h
4.23.5 13 (M) Low air pressure 1 kPa; (25 ± 10) °C; 1 h
4.23.6 30 (Db)
4.23.7 - DC load U = U
4.25.1 -
4.25.3 -
IEC
60068-2
TEST
METHOD
TEST PROCEDURE
Stability for product types:
Climatic
sequence:
Damp heat,
cyclic
Damp heat,
cyclic
Endurance
at 70 °C
Endurance
at 125 °C
55 °C; 90 % RH;
24 h; 1 cycle
55 °C; 90 % RH;
24 h; 5 cycles
U = U
1.5 h on; 0.5 h off;
70 °C; 1000 h ± (1 % R + 0.05 )± (2 % R + 0.1 )
70 °C; 8000 h ± (2 % R + 0.1 )± (4 % R + 0.1 )
125 °C, 1000 h ± (1 % R + 0.05 )± (2 % R + 0.1 )
CRCW....BC e3 1 to 10 M 1 to 10 M
-
max.
max.;
CRCW...BC e3
Vishay BCcomponents
REQUIREMENTS PERMISSIBLE CHANGE (R)
STABILITY
CLASS 1
OR BETTER
± (1 % R + 0.05 )± (2 % R + 0.1 )
STABILITY
CLASS 2
OR BETTER
APPLICABLE SPECIFICATIONS
• EN60115-1Generic specification
• EN140400Sectional specification
• EN140401-802Detail specification
Revision: 20-Apr-12
For technical questions, contact: f3aresistors@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
• IEC 60068-2-XVariety of environmental test procedures
• IEC 60286-3Packaging of SMD components
5
Document Number: 28743
Loading...