Datasheet CRCW0805, CRCW0201, CRCW0402, CRCW0603, CRCW1206 Specification

...
Page 1
CRCW...BC e3
www.vishay.com
Vishay BCcomponents
Lead (Pb)-free Thick Film, Rectangular Commodity Chip Resistors
FEATURES
• High volume product suitable for commercial applications
• Excellent stability (R/R 1 % for 1000 h at 70 °C)
• Lead (Pb)-free solder contacts on Ni barrier layer
• Metal glaze on high quality ceramic
• Protective overglaze
• Material categorization: For definitions of compliance please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
MODEL
CRCW0201...BC 0201 RR 0603M
CRCW0402...BC 0402 RR 1005M
CRCW0603...BC 0603 RR 1608M
CRCW0805...BC 0805 RR 2012M
CRCW1206...BC 1206 RR 3216M
CRCW1210...BC 1210 RR 3225M
CRCW2010...BC 2010 RR 5025M
CRCW2512...BC 2512 RR 6332M
Notes
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
• Power rating depends on the maximum temperature at the solder point, the component placement density and the substrate material
Revision: 15-Apr-13
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
CASE
SIZE
INCH
CASE
SIZE
METRIC
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
POWER RATING
P
70 °C
W
0.05 30
Zero-Ohm-Resistor: R
0.063 50
Zero-Ohm-Resistor: R
0.10 75
Zero-Ohm-Resistor: R
0.125 150
Zero-Ohm-Resistor: R
0.25 200
Zero-Ohm-Resistor: R
0.50 200
Zero-Ohm-Resistor: R
0.75 400
Zero-Ohm-Resistor: R
1.0 500
Zero-Ohm-Resistor: R
LIMITING ELEMENT VOLTAGE
MAX. V
max.
max.
max.
max.
max.
max.
max.
max.
TEMPERATURE
COEFFICIENT
= 50 m, I
= 20 m, I
= 20 m, I
= 20 m, I
= 20 m, I
= 20 m, I
= 20 m, I
= 20 m, I
1
TOLERANCE
ppm/K
± 200
- 200/+ 400 1R0 to 9R76 ± 100
- 200/+ 400 1R0 to 9R76 ± 200
- 200/+ 400 1R0 to 9R1
at 70 °C = 1.0 A
max.
± 100 ± 200 1R0 to 9R76 ± 200 ± 5 1R0 to 10M E24
at 70 °C = 1.5 A
max.
± 100 ± 200 1R0 to 9R76 ± 200 ± 5 1R0 to 10M E24
at 70 °C = 2.0 A
max.
± 100 ± 200 1R0 to 9R76 ± 200 ± 5 1R0 to 10M E24
at 70 °C = 2.5 A
max.
± 100 ± 200 1R0 to 9R76 ± 200 ± 5 1R0 to 10M E24
at 70 °C = 3.5 A
max.
± 100 ± 200 1R0 to 9R76 ± 200 ± 5 1R0 to 10M E24
at 70 °C = 4.0 A
max.
± 100 ± 200 1R0 to 9R76 ± 200 ± 5 1R0 to 10M E24
at 70 °C = 5.0 A
max.
± 100 ± 200 1R0 to 9R76 ± 200 ± 5 1R0 to 10M E24
at 70 °C = 7.0 A
max.
%
± 0.5
± 1
± 5
± 1
± 1
± 1
± 1
± 1
± 1
± 1
RESISTANCE
RANGE
10R to 10M
47R to 1M
10R to 10M
1R0 to 10M
1R0 to 10M
1R0 to 10M
1R0 to 10M
1R0 to 10M
1R0 to 10M
1R0 to 10M
Document Number: 28743
E-SERIES
E96
E24; E96± 200 10R to 10M
E24
E24; E96
E24; E96
E24; E96
E24; E96
E24; E96
E24; E96
E24; E96
Page 2
CRCW...BC e3
www.vishay.com
TECHNICAL SPECIFICATIONS
PARAMETER UNIT
Rated Dissipation at 70 °C
Limiting Element Voltage
U
Insulation Voltage
U
Insulation Resistance
Operating Temperature Range
Failure Rate °C 0.3 x 10
Weight/ 1000 Pieces
Note
(1)
(1)
AC/DC
max.
(1 min)
ins
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
CRCW0201...BC CRCW0402...BC CRCW0603...BC CRCW0805...BC CRCW1206...BC CRCW1210...BC CRCW2010...BC CRCW2512...BC
W 0.050 0.063 0.10 0.125 0.25 0.50 0.75 1.0
V 30 50 75 150 200 200 400 500
V 50 75 100 200 300 300 300 300
> 10
°C - 55 to + 155
g 0.17 0.65 2 5.5 10 16 25.5 40.5
9
-9
Vishay BCcomponents
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: CRCW0603562RFKTCBC
C R C W 0 6 0 3 5 6 2 R F K T C B C
MODEL VALUE TOLERANCE TCR PACKAGING Special
CRCW0201 CRCW0402 CRCW0603 CRCW0805 CRCW1206 CRCW1210 CRCW2010 CRCW2512
PRODUCT DESCRIPTION: CRCW0603-BC 100 562R 1 % RT6 e3
CRCW0603-BC 100 562R 1 % RT6 e3
MODEL TCR
CRCW0201-BC CRCW0402-BC CRCW0603-BC CRCW0805-BC CRCW1206-BC CRCW1210-BC CRCW2010-BC CRCW2512-BC
R = Decimal
K = Thousand
M = Million
0000 = Jumper
± 100 ppm/K ± 200 ppm/K
- 200 ppm/K/ + 400 ppm/K
D = ± 0.5 % F = ± 1.0 %
J = ± 5.0 % Z = Jumper
RESISTANCE
VALUE
10R = 10
562R = 562
10K = 10.0 k
1M = 1 M
0R0 = Jumper
K = ± 100 ppm/K N = ± 200 ppm/K X = - 200 ppm/K/
+ 400 ppm/K
0 = Jumper
TOLERANCE
VALUE
± 0.5 %
± 1 % ± 5 %
TA, TB TC, TD TE, TF
TH, TI
PACKAGING LEAD (Pb)-FREE
RT1, RT2 RT5, RT6 RT7, RF4 R02, R82
Up to 2 digits
BC = Commodity
e3 = Pure tin
termination finish
Revision: 15-Apr-13
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
2
Document Number: 28743
Page 3
CRCW...BC e3
www.vishay.com
PACKAGING
REEL
MODEL
TAPE WIDTH DIAMETER PITCH
180 mm/7"
CRCW0201…BC 8 mm
254 mm/10" 20 000 TI - RT2 -
2 mm
330 mm/13" 50 000 TE - RF4 -
180 mm/7"
CRCW0402…BC 8 mm
254 mm/10" 20 000 TI - RT2 -
2 mm
330 mm/13" 50 000 TE - RF4 -
180 mm/7"
CRCW0603…BC 8 mm
254 mm/10" 10 000 TB - RT5 -
4 mm
330 mm/13" 20 000 TC - RT6 -
180 mm/7"
CRCW0805…BC 8 mm
254 mm/10" 10 000 TB - RT5 -
4 mm
330 mm/13" 20 000 TC - RT6 -
180 mm/7"
CRCW1206…BC 8 mm
254 mm/10" 10 000 TB - RT5 -
4 mm
330 mm/13" 20 000 TC - RT6 -
180 mm/7"
CRCW1210…BC 8 mm
254 mm/10" 10 000 TB - RT5 -
4 mm
330 mm/13" 20 000 TC - RT6 -
CRCW2010…BC 12 mm 180 mm/7" 4 mm 4000 - TF - R02
CRCW2512…BC 12 mm 180 mm/7" 4 mm 4000 - TH - R82
PIECES/
REEL
PART NUMBER PRODUCT DESC.
PAPER BLISTER PAPER BLISTER
10 000 TD - RT7 -
10 000 TD - RT7 -
5000 TA - RT1 -
5000 TA - RT1 -
5000 TA - RT1 -
5000 TA - RT1 -
Vishay BCcomponents
PACKAGING CODE
DIMENSIONS in millimeters
SIZE DIMENSIONS
REFLOW SOLDERING WAVE SOLDERING
SOLDER PAD DIMENSIONS
INCH METRIC L W H T1 T2 a b l a b l
0201 0603 0.6 ± 0.05 0.3 ± 0.05 0.23 ± 0.05 0.15 ± 0.05 0.2
+ 0.05
- 0.10
0.30.430.2 - - -
0402 1005 1.0 ± 0.05 0.5 ± 0.05 0.35 ± 0.05 0.25 ± 0.05 0.2 ± 0.1 0.4 0.6 0.5 - - -
0603 1608 1.55
0805 2012 2.0
1206 3216 3.2
+ 0.10
0.85 ± 0.1 0.45 ± 0.05 0.3 ± 0.2 0.3 ± 0.2 0.5 0.9 1.0 0.9 0.9 1.0
- 0.05
+ 0.20
1.25 ± 0.15 0.45 ± 0.05 0.3
- 0.10
+ 0.10
1.6 ± 0.15 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 1.7 2.0 1.1 1.7 2.3
- 0.20
+ 0.20
0.3 ± 0.2 0.7 1.3 1.2 0.9 1.3 1.3
- 0.10
1210 3225 3.2 ± 0.2 2.5 ± 0.2 0.55 ± 0.05 0.45 ± 0.2 0.4 ± 0.2 0.9 2.5 2.0 1.1 2.5 2.2
2010 5025 5.0 ± 0.15 2.5 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 2.5 3.9 1.2 2.5 3.9
2512 6332 6.3 ± 0.2 3.15 ± 0.15 0.6 ± 0.1 0.6 ± 0.2 0.6 ± 0.2 1.0 3.2 5.2 1.2 3.2 5.2
Note
(1)
The rated dissipation applies only if the permitted film temperature is not exceeded. Furthermore, a high level of ambient temperature or of power dissipation may raise the temperature of the solder joint, hence special solder alloys or boardmaterials maybe required to maintain the reliability of the assembly. Specified power rating above 125 °C requires dedicated heat-sink pads, which depend on boardmaterials. The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g. in standards IEC 61188-5-x, or in publication IPC-7351. They do not guarantee any supposed thermal properties, particularly as these are also strongly influenced by many other parameters. Still the given solder pad dimensions will be found adequate for most general applications.
(2)
No marking for 0201 and 0402 sizes.
Revision: 15-Apr-13
3
Document Number: 28743
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
(1)
Page 4
P70 x R
www.vishay.com
DERATING
120
100
80
Rated Power in %
60
40
20
0
- 55 - 25 0 25 50 75 100 125 155 175 70
Ambient Temperature in °C
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1 CLAUSE
4.5 - Resistance - ± 1 % ± 5 %
4.8.4.2 -
4.13 -
4.17.5 58 (Td) Solderability
4.18.2 58 (Td)
4.19 14 (Na)
4.24 78 (Cab)
IEC
60068-2
TEST
METHOD
TEST PROCEDURE
Stability for product types:
Temperature
coefficient
Short time
overload
Resistance to soldering heat
Rapid change
of temperature
Damp heat, steady state
(20/- 55/20) °C and
(20/125/20) °C
U = 2.5 x  2 x U
duration: Acc. to the style
Pre-aging
4 h at 155 °C,
dryheat
Solder bath method
(260 ± 5) °C;
(10 ± 1) s
30 min. at - 55 °C; 30 min. at 125 °C;
1000 cycles ± (1 % R + 0.05 ) ± (1 % R + 0.05 ) ± (1 % R + 0.05 )
(40 ± 2) °C;
(93 ± 3) % RH
CRCW....BC e3 1 to 10 M 1 to 10 M 1 to 10 M
max.;
Solder bath
method;
Sn60Pb40
non activated flux;
(235 ± 5) °C
(2 ± 0.2) s
Solder bath
method;
Sn96.5Ag3Cu0.5
non activated flux;
(245 ± 5) °C
(3 ± 0.3) s
5 cycles ± (0.25 % R + 0.05 )± (0.5 % R + 0.05 )± (0.5 % R + 0.05 )
56 days;
REQUIREMENTS PERMISSIBLE CHANGE (R)
STABILITY
CLASS 1
OR BETTER
± 100 ppm/K,
± 200 ppm/K
± (0.25 % R + 0.05 )± (0.5 % R + 0.05 )± (1 % R + 0.05 )
± (0.25 % R + 0.05 )± (0.5 % R + 0.05 )± (1 % R + 0.05 )
± (1 % R + 0.05 (2 % R + 0.1
Vishay BCcomponents
STABILITY
CLASS 2
OR BETTER
± 200 ppm/K
Good tinning ( 95 % covered)
no visible damage
Good tinning ( 95 % covered)
no visible damage
CRCW...BC e3
SIZE 0201
± 0.5 %, ± 1 %, ± 5 %
± 100 ppm/K, ± 200 ppm/K,
- 200 ppm/K/ + 400 ppm/K
)± (2 % R + 0.1 )
Revision: 15-Apr-13
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
4
Document Number: 28743
Page 5
www.vishay.com
P70 x R
P70 x R
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1 CLAUSE
4.23 -
4.23.2 2 (Ba) Dry heat 125 °C; 16 h
4.23.3 30 (Db)
4.23.4 1 (Aa) Cold - 55 °C; 2 h
4.23.5 13 (M)
4.23.6 30 (Db)
4.23.7 - DC load U = U
4.25.1 -
4.25.3 -
IEC
60068-2
TEST
METHOD
TEST PROCEDURE
Stability for product types:
Climatic
sequence:
Damp heat,
cyclic
Low air
pressure
Damp heat,
cyclic
Endurance
at 70 °C
Endurance
at 125 °C
55 °C;  90 % RH;
24 h; 1 cycle
1 kPa; (25 ± 10) °C; 1 h
55 °C;  90 % RH;
24 h; 5 cycles
U = U
1.5 h on; 0.5 h off;
70 °C; 1000 h ± (1 % R + 0.05 (2 % R + 0.1 (2 % R + 0.1 )
70 °C; 8000 h ± (2 % R + 0.1 (4 % R + 0.1 (4 % R + 0.1 )
125 °C, 1000 h ± (1 % R + 0.05 (2 % R + 0.1 (2 % R + 0.1 )
CRCW....BC e3 1 to 10 M 1 to 10 M 1 to 10 M
-
max.
max.;
CRCW...BC e3
Vishay BCcomponents
REQUIREMENTS PERMISSIBLE CHANGE (R)
STABILITY
CLASS 1
OR BETTER
± (1 % R + 0.05 (2 % R + 0.1 (2 % R + 0.1 )
STABILITY
CLASS 2
OR BETTER
SIZE 0201
APPLICABLE SPECIFICATIONS
• EN60115-1Generic specification
• EN140400Sectional specification
• EN140401-802Detail specification
Revision: 15-Apr-13
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
• IEC 60068-2-XVariety of environmental test procedures
• IEC 60286-3Packaging of SMD components
5
Document Number: 28743
Loading...