How it Works
Datasheet
Loading...
COP8SAC744V8
Datasheet (NSC)
60 pgs795.27 Kb0

Datasheet COP8SAC744V8 Datasheet (NSC)

Download
Page 1
PRELIMINARY
November 2000
COP8SA Family 8-Bit CMOS ROM Based and One-Time Programmable (OTP) Microcontroller with 1k to 4k Memory, Power On Reset, and Very Small Packaging
COP8SA Family, 8-Bit CMOS ROM Based and One-Time Programmable (OTP) Microcontroller
with 1k to 4k Memory, Power On Reset, and Very Small Packaging
General Description
Note: COP8SAx devices are instruction set and pin com­patible supersets of the COP800 Family devices, and are replacements for these in new designs when possible.
Device
COP8SAA5 1k ROM 64 12/16/24 16/20/28 DIP/SOIC, 28 CSP 0 to +70˚C, -40 to +85˚C,
COP8SAB5 2k ROM 128 16/24 20/28 DIP/SOIC, 28 CSP 0 to +70˚C, -40 to +85˚C,
COP8SAC5 4k ROM 128 16/24/36/40 20/28 DIP/SOIC, 28 CSP,
COP8SAA7 1k OTP EPROM 64 12/16/24 16/20/28 DIP/SOIC, 28 CSP 0 to +70˚C, -40 to +85˚C,
COP8SAB7 2k OTP EPROM 128 16/24 20/28 DIP/SOIC, 28 CSP 0 to +70˚C, -40 to +85˚C,
COP8SAC7 4k OTP EPROM 128 16/24 20/28 DIP/SOIC, 28 CSP,
COP8SAC7-Q3 4k EPROM 128 16/24/36 20/28/40 DIP Room Temp. Only COP8SAC7-J3 4k EPROM 128 40 44 PLCC Room Temp. Only
™
feature core devices, with 1k to 4k
Memory
(bytes)
RAM
(bytes)
I/O Pins
Family features include an 8-bit memory mapped architec­ture, 10 MHz CKI with 1 µs instruction cycle, one multi­function 16-bit timer/counter with PWM output, MICROWIRE/PLUS IDLE modes, MIWU, idle timer, on-chip R/C oscillator, 12 high current outputs, user selectable options (WATCH-
™
DOG
, 4 clock/oscillator modes, power-on-reset), low EMI
2.7V to 5.5V operation, and 16/20/28/40/44 pin packages. Devices included in this datasheet are:
Packages Temperature
40 DIP, 44 PLCC/QFP
40 DIP, 44 PLCC/QFP
™
serial I/O, two power saving HALT/
-40 to +125˚C
-40 to +125˚C 0 to +70˚C, -40 to +85˚C,
-40 to +125˚C
-40 to +125˚C
-40 to +125˚C 0 to +70˚C, -40 to +85˚C,
-40 to +125˚C
Key Features
n Low cost 8-bit OTP microcontroller n OTP program space with read/write protection (fully
secured)
n Quiet Design (low radiated emissions) n Multi-Input Wakeup pins with optional interrupts
(4 to 8 pins)
n 8 bytes of user storage space in EPROM
TRI-STATE®is a registered trademark of National Semiconductor Corporation. MICROWIRE/PLUS iceMASTER
© 2000 National Semiconductor Corporation DS012838 www.national.com
™
, COP8™, MICROWIRE™and WATCHDOG™are trademarks of National Semiconductor Corporation.
®
is a registered trademark of MetaLink Corporation.
n User selectable clock options
— Crystal/Resonator options — Crystal/Resonator option with on-chip bias resistor — External oscillator — Internal R/C oscillator
n Internal Power-On Reset—user selectable n WATCHDOG and Clock Monitor Logic— user selectable n Up to 12 high current outputs
Page 2
CPU Features
n Versatile easy to use instruction set n 1 µs instruction cycle time n Eight multi-source vectored interrupts servicing
— External interrupt
COP8SA Family
— Idle Timer T0 — One Timer (with 2 interrupts) — MICROWIRE/PLUS Serial Interface — Multi-Input Wake Up — Software Trap — Default VIS (default interrupt)
n 8-bit Stack Pointer SP (stack in RAM) n Two 8-bit Register Indirect Data Memory Pointers n True bit manipulation n Memory mapped I/O n BCD arithmetic instructions
Peripheral Features
n Multi-Input Wakeup Logic n One 16-bit timer with two 16-bit registers supporting:
— Processor Independent PWM mode — External Event counter mode — Input Capture mode
n Idle Timer n MICROWIRE/PLUS Serial Interface (SPI Compatible)
I/O Features
n Software selectable I/O options
— TRI-STATE — Push-Pull Output — Weak Pull Up Input — High Impedance Input
n Schmitt trigger inputs on ports G and L n Up to 12 high current outputs n Pin efficient (i.e., 40 pins in 44-pin package are devoted
to useful I/O)
®
Output
Fully Static CMOS Design
n Low current drain (typically<4 µA) n Single supply operation: 2.7V to 5.5V n Two power saving modes: HALT and IDLE
Temperature Ranges
0˚C to +70˚C, −40˚C to +85˚C, and −40˚C to +125˚C
Development Support
n Windowed packages for DIP and PLCC n Real time emulation and full program debug offered by
MetaLink Development System
Block Diagram
DS012838-1
FIGURE 1. COP8SAx Block Diagram
www.national.com 2
Page 3
General Description (Continued)
Key features include an 8-bit memory mapped architecture, a 16-bit timer/counter with two associated 16-bit registers supporting three modes (Processor Independent PWM gen­eration, External Event counter, and Input Capture capabili­ties), two power saving HALT/IDLE modes with a multi-sourced wakeup/interrupt capability, on-chip R/C oscil­lator, high current outputs, user selectable options such as WATCHDOG, Oscillator configuration, and power-on-reset.
1.1 EMI REDUCTION
The COP8SAx family of devices incorporates circuitry that guards against electromagnetic interference—an increasing problem in today’s microcontroller board designs. National’s patented EMI reduction technology offers low EMI clock circuitry, gradual turn-on output drivers (GTOs) and internal I
smoothing filters, to help circumvent many of the EMI
CC
issues influencing embedded control designs. National has achieved 15 dB–20 dB reduction in EMI transmissions when designs have incorporated its patented EMI reducing cir­cuitry.
1.2 ARCHITECTURE
The COP8SAx family is based on a modified Harvard archi­tecture, which allows data tables to be accessed directly from program memory. This is very important with modern microcontroller-based applications, since program memory is usually ROM or EPROM, while data memory is usually RAM. Consequently data tables usually need to be con­tained in ROM or EPROM, so they are not lost when the microcontroller is powered down. In a modified Harvard ar­chitecture, instruction fetch and memory data transfers can be overlapped with a two stage pipeline, which allows the next instruction to be fetched from program memory while the current instruction is being executed using data memory. This is not possible with a Von Neumann single-address bus architecture.
The COP8SAx family supports a software stack scheme that allows the user to incorporate many subroutine calls. This capability is important when using High Level Languages. With a hardware stack, the user is limited to a small fixed number of stack levels.
1.3 INSTRUCTION SET
In today’s 8-bit microcontroller application arena cost/ performance, flexibility and time to market are several of the key issues that system designers face in attempting to build well-engineered products that compete in the marketplace. Many of these issues can be addressed through the manner in which a microcontroller’s instruction set handles process­ing tasks. And that’s why COP8 family offers a unique and code-efficient instruction set—one that provides the flexibil­ity,functionality, reduced costs and faster time to market that today’s microcontroller based products require.
Code efficiency is important because it enables designers to pack more on-chip functionality into less program memory space (ROM/OTP). Selecting a microcontroller with less pro­gram memory size translates into lower system costs, and the added security of knowing that more code can be packed into the available program memory space.
1.3.1 Key Instruction Set Features
The COP8SAx family incorporates a unique combination of instruction set features, which provide designers with opti­mum code efficiency and program memory utilization.
COP8SA Family
Single Byte/Single Cycle Code Execution
The efficiency is due to the fact that the majority of instruc­tions are of the single byte variety, resulting in minimum program space. Because compact code does not occupy a substantial amount of program memory space, designers can integrate additional features and functionality into the microcontroller program memory space. Also, the majority instructions executed by the device are single cycle, result­ing in minimum program execution time. In fact, 77% of the instructions are single byte single cycle, providing greater code and I/O efficiency, and faster code execution.
1.3.2 Many Single-Byte, Multifunction Instructions
The COP8SAx instruction set utilizes many single-byte, mul­tifunction instructions. This enables a single instruction to accomplish multiple functions, such as DRSZ, DCOR, JID, and LOAD/EXCHANGE instructions with post-incrementing and post-decrementing, to name just a few examples. In many cases, the instruction set can simultaneously execute as many as three functions with the same single-byte in­struction.
JID: (Jump Indirect); Single byte instruction; decodes exter­nal events and jumps to corresponding service routines (analogous to “DO CASE” statements in higher level lan­guages).
LAID: (Load Accumulator-Indirect); Single byte look up table instruction provides efficient data path from the program memory to the CPU. This instruction can be used for table lookup and to read the entire program memory for checksum calculations.
RETSK: (Return Skip); Single byte instruction allows return from subroutine and skips next instruction. Decision to branch can be made in the subroutine itself, saving code.
AUTOINC/DEC: (Auto-Increment/Auto-Decrement); These instructions use the two memory pointers B and X to effi­ciently process a block of data (analogous to “FOR NEXT” in higher level languages).
1.3.3 Bit-Level Control
Bit-level control over many of the microcontroller’s I/O ports provides a flexible means to ease layout concerns and save board space. All members of the COP8 family provide the ability to set, reset and test any individual bit in the data memory address space, including memory-mapped I/O ports and associated registers. Three memory-mapped pointers handle register indirect addressing and software stack pointer functions. The memory data pointers allow the option of post-incrementing or post-decrementing with the data movement instructions (LOAD/EXCHANGE). And 15 memory-maped registers allow designers to optimize the precise implementation of certain specific instructions.
1.4 PACKAGING/PIN EFFICIENCY
Real estate and board configuration considerations demand maximum space and pin efficiency, particularly given today’s high integration and small product form factors. Microcon­troller users try to avoid using large packages to get the I/O needed. Large packages take valuable board space and increases device cost, two trade-offs that microcontroller designs can ill afford.
The COP8 family offersawiderangeofpackagesanddo not waste pins: up to 90.9% (or 40 pins in the 44-pin package) are devoted to useful I/O.
www.national.com3
Page 4
Connection Diagrams
COP8SA Family
Top View
DS012838-2
DS012838-3
Top View
DS012838-4
Top View
Top View
DS012838-39
Top View
DS012838-6
Top View
DS012838-5
FIGURE 2. Connection Diagrams
www.national.com 4
Page 5
Ordering Information
DS012838-8
FIGURE 3. Part Numbering Scheme
1k EPROM 2k EPROM 4k EPROM 4k EPROM
Windowed
Device
Temperature Order Number Package Order Number Package Order Number Package Order Number Package
0˚C to +70˚C COP8SAA716M9 16M
COP8SAA720M9 20M COP8SAB720M9 20M COP8SAC720M9 20M COP8SAA728M9 28M COP8SAB728M9 28M COP8SAC728M9 28M COP8SAA716N9 16N COP8SAA720N9 20N COP8SAB720N9 20N COP8SAC720N9 20N COP8SAC720Q3 20Q COP8SAA728N9 28N COP8SAB728N9 28N COP8SAC728N9 28N COP8SAC728Q3 28Q
COP8SAC740N9 40N COP8SAC740Q3 40Q COP8SAC744V9 44V COP8SAC744J3 44J
−40˚C to +85˚C COP8SAA716M8 16M COP8SAA720M8 20M COP8SAB720M8 20M COP8SAC720M8 20M COP8SAA728M8 28M COP8SAB728M8 28M COP8SAC728M8 28M COP8SAA716N8 16N COP8SAA720N8 20N COP8SAB720N8 20N COP8SAC720N8 20N COP8SAA728N8 28N COP8SAB728N8 28N COP8SAC728N8 28N
COP8SAC740N8 40N COP8SAC744V8 44V
COP8SAA7SLB8 SLB COP8SAB7SLB8 SLB COP8SAC7SLB8 SLB
−40˚C to +125˚C
COP8SAC720M7 20M COP8SAC728M7 28M COP8SAC720N7 20N COP8SAC728N7 28N COP8SAC740N7 40N COP8SAC744V7 44V
COP8SA Family
www.national.com5
Page 6
4.0 Electrical Characteristics
ESD Protection Level 2 kV
(Human Body Model)
Absolute Maximum Ratings
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications.
COP8SA Family
Supply Voltage (V Voltage at Any Pin −0.6V to V
)7V
CC
(Note 1)
CC
+0.6V
Total Current into V
Pin (Source) 80 mA
CC
Total Current out of GND Pin (Sink) 100 mA Storage Temperature Range −65˚C to +140˚C
Note 1:
Absolute maximum ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications are not ensured when operating the device at absolute maximum ratings.
DC Electrical Characteristics
0˚C ≤ TA≤ +70˚C unless otherwise specified.
Parameter Conditions Min Typ Max Units
Operating Voltage (Note 8) 2.7 5.5 V Power Supply Rise Time from 0.0V
(On-Chip Power-On Reset Selected) 10 ns 50 ms
V
Start Voltage to Guarantee POR 0.25 V
CC
Power Supply Ripple (Note 3) Peak-to-Peak 0.1 V Supply Current (Note 4)
CKI = 10 MHz V CKI = 4 MHz V
HALT Current (Note 5) —WATCHDOG Disabled V
= 5.5V, tC= 1 µs 6 mA
CC
= 4.5V, tC= 2.5 µs 2.1 mA
CC
= 5.5V, CKI = 0 MHz
CC
<
48 µA
IDLE Current (Note 4)
CKI = 10 MHz V CKI = 4 MHz V
Input Levels (V
IH,VIL
)
= 5.5V, tC= 1 µs 1.5 mA
CC
= 4.5V, tC= 2.5 µs 0.8 mA
CC
RESET
Logic High 0.8 V
CC
Logic Low 0.2 V
CKI, All Other Inputs
Logic High 0.7 V
CC
Logic Low 0.2 V Value of the Internal Bias Resistor 0.5 1.0 2.0 MΩ for the Crystal/Resonator Oscillator CKI Resistance to V
or GND when R/C VCC= 5.5V 5 8 11 kΩ
CC
Oscillator is Selected Hi-Z Input Leakage (same as TRI-STATE output) V Input Pullup Current V G and L Port Input Hysteresis 0.25 V
= 5.5V −2 +2 µA
CC
= 5.5V, VIN= 0V −40 −250 µA
CC
CC
CC
CC
CC
V
V V
V V
V
www.national.com 6
Page 7
DC Electrical Characteristics (Continued)
0˚C ≤ TA≤ +70˚C unless otherwise specified.
Parameter Conditions Min Typ Max Units
Output Current Levels D Outputs
Source V
Sink V
L Port
Source (Weak Pull-Up) V
Source (Push-Pull Mode) V
Sink (L0–L3, Push-Pull Mode) V
Sink (L4–L7, Push-Pull Mode) V
All Others
Source (Weak Pull-Up Mode) V
Source (Push-Pull Mode) V
Sink (Push-Pull Mode) V
Allowable Sink Current per Pin (Note 8)
D Outputs and L0 to L3 15 mA
All Others 3mA Maximum Input Current without Latchup (Note 6) RAM Retention Voltage, Vr 2.0 V V
Rise Time from a VCC≥ 2.0V (Note 9) 12 µs
CC
Input Capacitance (Note 8) 7 pF Load Capacitance on D2 (Note 8) 1000 pF
= 4.5V, VOH= 3.3V −0.4 mA
CC
V
= 2.7V, VOH= 1.8V −0.2 mA
CC
= 4.5V, VOL= 1.0V 10 mA
CC
V
= 2.7V, VOL= 0.4V 2 mA
CC
= 4.5V, VOH= 2.7V −10 −110 µA
CC
V
= 2.7V, VOH= 1.8V −2.5 −33 µA
CC
= 4.5V, VOH= 3.3V −0.4 mA
CC
V
= 2.7V, VOH= 1.8V −0.2 mA
CC
= 4.5V, VOL= 1.0V 10 mA
CC
V
= 2.7V, VOL= 0.4V 2 mA
CC
= 4.5V, VOL= 0.4V 1.6 mA
CC
V
= 2.7V, VOL= 0.4V 0.7 mA
CC
= 4.5V, VOH= 2.7V −10 −110 µA
CC
V
= 2.7V, VOH= 1.8V −2.5 −33 µA
CC
= 4.5V, VOH= 3.3V −0.4 mA
CC
V
= 2.7V, VOH= 1.8V −0.2 mA
CC
= 4.5V, VOL= 0.4V 1.6 mA
CC
V
= 2.7V, VOL= 0.4V 0.7 mA
CC
±
200 mA
COP8SA Family
www.national.com7
Page 8
AC Electrical Characteristics
0˚C ≤ TA≤ +70˚C unless otherwise specified.
Parameter Conditions Min Typ Max Units
Instruction Cycle Time (t
Crystal/Resonator, External 4.5V ≤ V
COP8SA Family
Internal R/C Oscillator 4.5V ≤ V
R/C Oscillator Frequency Variation 4.5V ≤ V (Note 8) 2.7V ≤ V
External CKI Clock Duty Cycle (Note 8) fr = Max 45 55 %
Rise Time (Note 8) fr = 10 MHz Ext Clock 12 ns Fall Time (Note 8) fr = 10 MHz Ext Clock 8 ns
Inputs
t
SETUP
t
HOLD
Output Propagation Delay (Note 7) R
t
PD1,tPD0
SO, SK 4.5V ≤ VCC≤ 5.5V 0.7 µs
All Others 4.5V ≤ V
MICROWIRE Setup Time (t MICROWIRE Hold Time (t MICROWIRE Output Propagation Delay (t MICROWIRE Maximum Shift Clock
Master Mode 500 kHz Slave Mode 1 MHz
Input Pulse Width (Note 7)
Interrupt Input High Time 1 t Interrupt Input Low Time 1 t Timer 1 Input High Time 1 t Timer 1 Input Low Time 1 t
Reset Pulse Width 1 µs
Note 2: tC= Instruction cycle time (Clock input frequency divided by 10). Note 3: Maximum rate of voltage change must be Note 4: Supply and IDLE currents are measured with CKI driven with a square wave Oscillator, CKO driven 180˚ out of phase with CKI, inputs connected to V
and outputs driven low but not connected to a load. Note 5: The HALTmode will stop CKI from oscillating in the R/C and the Crystal configurations. In the R/C configuration, CKI is forced high internally. In the crystal
or external configuration, CKI is TRI-STATE. Measurement of I programmed aslow outputs andnot driving a load; all outputs programmed low and not drivinga load; allinputs tied toV Parameter refers to HALT mode entered via setting bit 7 of the G Port data register.
Note 6: Pins G6 and RESET are designed witha high voltage input network. These pins allow input voltages biased at voltages>VCC(the pins do not have source current when biased at a voltage below VCC). The effective resistance to VCCis 750Ω (typical). These two pins will not latch up. The voltage at the pins must be limited to
excludes ESD transients. Note 7: The output propagation delay is referenced to the end of the instruction cycle where the output change occurs. Note 8: Parameter characterized but not tested. Note 9: Rise times faster than this specification may reset the device if POR is enabled and may affect the value of Idle Timer T0 if POR is not enabled.
)
C
≤ 5.5V 1.0 DC µs
CC
2.7V ≤ V
2.7V ≤ V
<
4.5V 2.0 DC µs
CC
≤ 5.5V 1.667 µs
CC
<
4.5V TBD µs
CC
≤ 5.5V
CC
<
4.5V TBD %
CC
±
35 %
4.5V ≤ VCC≤ 5.5V 200 ns
2.7V ≤ V
<
4.5V 500 ns
CC
4.5V ≤ VCC≤ 5.5V 60 ns
2.7V ≤ V = 2.2k, CL= 100 pF
L
2.7V ≤ V
2.7V ≤ V
) (Note 7) 20 ns
UWS
) (Note 7) 56 ns
UWH
) 220 ns
UPD
<
0.5 V/ms.
HALT is done with device neither sourcing nor sinking current; with L. F, C, G0, and G2–G5
DD
<
14V. WARNING: Voltages in excess of 14V will cause damage to the pins. This warning
<
4.5V 150 ns
CC
<
4.5V 1.75 µs
CC
≤ 5.5V 1.0 µs
CC
<
4.5V 2.5 µs
CC
; WATCHDOG andclock monitor disabled.
CC
>
VCCand the pins will have sink currentto VCCwhen
C C C C
CC
www.national.com 8
Page 9
COP8SA Family
Absolute Maximum Ratings (Note 10)
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications.
Supply Voltage (V Voltage at Any Pin −0.6V to V
)7V
CC
+0.6V
CC
Total Current into V Total Current out of GND Pin (Sink) 100 mA Storage Temperature Range −65˚C to +140˚C
Note 10:
Absolute maximum ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications are not ensured when operating the device at absolute maximum ratings.
Pin (Source) 80 mA
CC
ESD Protection Level 2 kV
(Human Body Model)
DC Electrical Characteristics
−40˚C ≤ TA≤ +85˚C unless otherwise specified.
Parameter Conditions Min Typ Max Units
Operating Voltage 2.7 5.5 V Power Supply Rise Time from 0.0V (Note 17)
(On-Chip Power-On Reset Selected) 10 ns 50 ms
V
Start Voltage to Guarantee POR 0.25 V
CC
Power Supply Ripple (Note 12) Peak-to-Peak 0.1 V
CC
Supply Current (Note 13)
CKI = 10 MHz V
HALT Current (Note 14) —WATCHDOG Disabled V
= 5.5V, tC= 1 µs 6.0 mA
CC
= 5.5V, CKI = 0 MHz
CC
<
4 10.0 µA
IDLE Current (Note 13)
CKI = 10 MHz V
Input Levels (V
IH,VIL
)
= 5.5V, tC= 1 µs 1.5 mA
CC
RESET
Logic High 0.8 V Logic Low 0.2 V
CC
CC
CKI, All Other Inputs
Logic High 0.7 V Logic Low 0.2 V
CC
CC
Value of the Internal Bias Resistor 0.5 1.0 2.0 MΩ for the Crystal/Resonator Oscillator CKI Resistance to V
or GND when R/C VCC= 5.5V 5 8 11 kΩ
CC
Oscillator is Selected Hi-Z Input Leakage (same as TRI-STATE output) V Input Pullup Current V G and L Port Input Hysteresis 0.25 V
= 5.5V −2 +2 µA
CC
= 5.5V, VIN= 0V −40 −250 µA
CC
CC
V
V V
V V
V
www.national.com9
Page 10
DC Electrical Characteristics (Continued)
−40˚C ≤ TA≤ +85˚C unless otherwise specified.
Parameter Conditions Min Typ Max Units
Output Current Levels D Outputs
COP8SA Family
Source V
Sink V
L Port
Source (Weak Pull-Up) V
Source (Push-Pull Mode) V
Sink (L0–L3, Push-Pull Mode) V
Sink (L4–L7, Push-Pull Mode) V
All Others
Source (Weak Pull-Up Mode) V
Source (Push-Pull Mode) V
Sink (Push-Pull Mode) V
Allowable Sink Current per Pin (Note 17)
D Outputs and L0 to L3 15 mA
All Others 3mA Maximum Input Current without Latchup (Note 15) RAM Retention Voltage, Vr 2.0 V V
Rise Time from a VCC≥ 2.0V (Note 18) 12 µs
CC
Input Capacitance (Note 17) 7 pF Load Capacitance on D2 (Note 17) 1000 pF
= 4.5V, VOH= 3.3V −0.4 mA
CC
V
= 2.7V, VOH= 1.8V −0.2 mA
CC
= 4.5V, VOL= 1.0V 10 mA
CC
V
= 2.7V, VOL= 0.4V 2 mA
CC
= 4.5V, VOH= 2.7V −10.0 −110 µA
CC
V
= 2.7V, VOH= 1.8V −2.5 −33 µA
CC
= 4.5V, VOH= 3.3V −0.4 mA
CC
V
= 2.7V, VOH= 1.8V −0.2 mA
CC
= 4.5V, VOL= 1.0V 10.0 mA
CC
V
= 2.7V, VOL= 0.4V 2 mA
CC
= 4.5V, VOL= 0.4V 1.6 mA
CC
V
= 2.7V, VOL= 0.4V 0.7 mA
CC
= 4.5V, VOH= 2.7V −10.0 −110 µA
CC
V
= 2.7V, VOH= 1.8V −2.5 −33 µA
CC
= 4.5V, VOH= 3.3V −0.4 mA
CC
V
= 2.7V, VOH= 1.8V −0.2 mA
CC
= 4.5V, VOL= 0.4V 1.6 mA
CC
V
= 2.7V, VOL= 0.4V 0.7 mA
CC
±
200 mA
AC Electrical Characteristics
−40˚C ≤ TA≤ +85˚C unless otherwise specified.
Parameter Conditions Min Typ Max Units
Instruction Cycle Time (t
Crystal/Resonator, External 4.5V ≤ V
Internal R/C Oscillator 4.5V ≤ V
R/C Oscillator Frequency Variation 4.5V ≤ V
(Note 17) 2.7V ≤ V External CKI Clock Duty Cycle (Note 17) fr = Max 45 55 %
Rise Time (Note 17) fr = 10 MHz Ext Clock 12 ns
Fall Time (Note 17) fr = 10 MHz Ext Clock 8 ns
www.national.com 10
)
C
≤ 5.5V 1.0 DC µs
CC
2.7V ≤ V
2.7V ≤ V
<
4.5V 2.0 DC µs
CC
≤ 5.5V 1.667 µs
CC
<
4.5V TBD µs
CC
≤ 5.5V
CC
<
4.5V TBD %
CC
±
35 %
Page 11
AC Electrical Characteristics (Continued)
−40˚C ≤ TA≤ +85˚C unless otherwise specified.
Parameter Conditions Min Typ Max Units
Inputs
t
SETUP
t
HOLD
Output Propagation Delay (Note 16) R
t
PD1,tPD0
SO, SK 4.5V ≤ VCC≤ 5.5V 0.7 µs
All Others 4.5V ≤ V
MICROWIRE Setup Time (t MICROWIRE Hold Time (t MICROWIRE Output Propagation Delay (t
) (Note 16) 20 ns
UWS
) (Note 16) 56 ns
UWH
UPD
MICROWIRE Maximum Shift Clock
Master Mode 500 kHz Slave Mode 1 MHz
Input Pulse Width (Note 17)
Interrupt Input High Time 1 t Interrupt Input Low Time 1 t Timer 1 Input High Time 1 t Timer 1 Input Low Time 1 t
Reset Pulse Width 1 µs
Note 11: tC= Instruction cycle time (Clock input frequency divided by 10). Note 12: Maximum rate of voltage change must be Note 13: Supply and IDLE currents are measured with CKI driven with a square wave Oscillator, CKO driven 180˚ out of phase with CKI, inputs connected to V
and outputs driven low but not connected to a load. Note 14: The HALT mode will stop CKI from oscillating in theR/C and the Crystal configurations. In the R/C configuration, CKI is forced high internally. In the crystal
or external configuration, CKI is TRI-STATE. Measurement of I programmed aslow outputs and not driving a load;all outputs programmed lowand not driving a load; all inputstied to V to HALT mode entered via setting bit 7 of the G Port data register.
Note 15: Pins G6and RESET aredesigned with ahigh voltage input network. Thesepins allow inputvoltages biased at voltages>VCC(the pins do not have source current when biased at a voltage below VCC). The effective resistance to VCCis 750Ω (typical). These two pins will not latch up. The voltage at the pins must be limited to ESD transients.
Note 16: The output propagation delay is referenced to the end of the instruction cycle where the output change occurs. Note 17: Parameter characterized but not tested. Note 18: Rise times faster than this specification may reset the device if POR is enabled and may affect the value of Idle Timer T0 if POR is not enabled.
4.5V ≤ VCC≤ 5.5V 200 ns
2.7V ≤ V
<
4.5V 500 ns
CC
4.5V ≤ VCC≤ 5.5V 60 ns
2.7V ≤ V = 2.2k, CL= 100 pF
L
2.7V ≤ V
2.7V ≤ V
<
4.5V 150 ns
CC
<
4.5V 1.75 µs
CC
≤ 5.5V 1.0 µs
CC
<
4.5V 2.5 µs
CC
) 220 ns
<
0.5 V/ms.
HALT is done with device neither sourcing nor sinking current; with L. F, C, G0, and G2–G5
DD
>
<
14V.WARNING: Voltages in excess of 14V will cause damage to the pins. This warning excludes
; clockmonitor disabled. Parameter refers
CC
VCCand thepins will havesink current toVCCwhen
COP8SA Family
C C C C
CC
DS012838-9
FIGURE 4. MICROWIRE/PLUS Timing
www.national.com11
Page 12
Absolute Maximum Ratings (Note 19)
If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications.
Supply Voltage (V
COP8SA Family
Voltage at Any Pin −0.6V to V
)7V
CC
CC
+0.6V
Total Current into V Total Current out of GND Pin (Sink) 100 mA Storage Temperature Range −65˚C to +140˚C
Note 19:
Absolute maximum ratings indicate limits beyond which damage to the device may occur. DC and AC electrical specifications are not ensured when operating the device at absolute maximum ratings.
Pin (Source) 80 mA
CC
ESD Protection Level 2 kV
(Human Body Model)
DC Electrical Characteristics
−40˚C ≤ TA≤ +125˚C unless otherwise specified.
Parameter Conditions Min Typ Max Units
Operating Voltage 4.5 5.5 V Power Supply Rise Time from 0.0V (Note 17)
(On-Chip Power-On Reset Selected) 10 ns 50 ms
V
Start Voltage to Guarantee POR 0.25 V
CC
Power Supply Ripple (Note 12) Peak-to-Peak 0.1 V Supply Current (Note 13)
CKI = 10 MHz V
HALT Current (Note 14) —WATCHDOG
= 5.5V, tC= 1 µs 6.0 mA
CC
V
= 5.5V, CKI = 0 MHz
CC
<
10 30 µA
Disabled IDLE Current (Note 13)
CKI = 10 MHz V
Input Levels (V
IH,VIL
)
= 5.5V, tC= 1 µs 1.5 mA
CC
RESET
Logic High 0.8 V
CC
Logic Low 0.2 V
CKI, All Other Inputs
Logic High 0.7 V
CC
Logic Low 0.2 V Value of the Internal Bias Resistor 0.5 1.0 2.0 MΩ for the Crystal/Resonator Oscillator CKI Resistance to V
or GND when R/C VCC= 5.5V 5 8 11 kΩ
CC
Oscillator is Selected Hi-Z Input Leakage V Input Pullup Current V G and L Port Input Hysteresis 0.25 V
= 5.5V −5 +5 µA
CC
= 5.5V, VIN= 0V −35 −400 µA
CC
CC
Output Current Levels D Outputs
Source V
Sink V
= 4.5V, VOH= 3.3V −0.4 mA
CC
= 4.5V, VOL= 1.0V 9 mA
CC
L Port
Source (Weak Pull-Up) V
Source (Push-Pull Mode) V
Sink (L0–L3, Push-Pull Mode) V
Sink (L4–L7, Push-Pull Mode) V
= 4.5V, VOH= 2.7V −9 −140 µA
CC
= 4.5V, VOH= 3.3V −0.4 mA
CC
= 4.5V, VOL= 1.0V 9 mA
CC
= 4.5V, VOL= 0.4V 1.4 mA
CC
All Others
Source (Weak Pull-Up Mode) V
Source (Push-Pull Mode) V
Sink (Push-Pull Mode) V TRI-STATE Leakage V
= 4.5V, VOH= 2.7V −9 −140 µA
CC
= 4.5V, VOH= 3.3V −0.4 mA
CC
= 4.5V, VOL= 0.4V 1.4 mA
CC
= 5.5V −5 +5 µA
CC
CC
CC
CC
V
V V
V V
V
www.national.com 12
Page 13
DC Electrical Characteristics (Continued)
−40˚C ≤ TA≤ +125˚C unless otherwise specified.
Parameter Conditions Min Typ Max Units
Allowable Sink Current per Pin (Note 17)
D Outputs and L0 to L3 15 mA All Others 3mA
Maximum Input Current without Latchup Room Temp
±
200 mA (Note 15) RAM Retention Voltage, Vr 2.0 V V
Rise Time from a VCC≥ 2.0V (Note 18) 12 µs
CC
Input Capacitance (Note 17) 7 pF Load Capacitance on D2 (Note 17) 1000 pF
AC Electrical Characteristics
−40˚C ≤ TA≤ +125˚C unless otherwise specified.
Parameter Conditions Min Typ Max Units
Instruction Cycle Time (t
Crystal/Resonator, External 4.5V ≤ V Internal R/C Oscillator 4.5V ≤ V R/C Oscillator Frequency Variation 4.5V ≤ V (Note 6)
External CKI Clock Duty Cycle (Note 6) fr = Max 45 55 %
Rise Time (Note 6) fr = 10 MHz Ext Clock 12 ns Fall Time (Note 6) fr = 10 MHz Ext Clock 8 ns
Inputs
t
SETUP
t
HOLD
Output Propagation Delay (Note 5) R
t
PD1,tPD0
SO, SK 4.5V ≤ VCC≤ 5.5V 0.7 µs
All Others 4.5V ≤ V MICROWIRE Setup Time (t MICROWIRE Hold Time (t MICROWIRE Output Propagation Delay (t MICROWIRE Maximum Shift Clock
Master Mode 500 kHz
Slave Mode 1 MHz Input Pulse Width (Note 6)
Interrupt Input High Time 1 t
Interrupt Input Low Time 1 t
Timer 1, 2, 3 Input High Time 1 t
Timer 1, 2, 3 Input Low Time 1 t Reset Pulse Width 1 µs
)
C
≤ 5.5V 1.0 DC µs
CC
≤ 5.5V 1.667 DC µs
CC
≤ 5.5V TBD %
CC
4.5V ≤ VCC≤ 5.5V 200 ns
4.5V ≤ VCC≤ 5.5V 60 ns = 2.2k, CL= 100 pF
L
≤ 5.5V 1.0 µs
CC
) (Note 5) 20 ns
UWS
) (Note 5) 56 ns
UWH
) 220 ns
UPD
C C C C
COP8SA Family
www.national.com13
Page 14
5.0 Pin Descriptions
COP8SAx I/O structure minimizes external component requirements. Software-switchable I/O enables designers to reconfigure the microcontroller’s I/O functions with a single instruction. Each individual I/O pin can be indepen­dently configured as an output pin low, an output high, an
COP8SA Family
input with high impedance or an input with a weak pull-up device. A typical example is the use of I/O pins as the keyboard matrix input lines. The input lines can be pro­grammed with internal weak pull-ups so that the input lines read logic high when the keys are all up. With a key closure, the corresponding input line will read a logic zero since the weak pull-up can easily be overdriven. When the key is released, the internal weak pullup will pull the input line back to logic high. This flexibility eliminates the need for external pull-up resistors. The High current options are available for driving LEDs, motors and speakers. This flexibility helps to ensure a cleaner design, with less ex­ternal components and lower costs. Below is the general description of all available pins.
V
and GND are the power supply pins. All VCCand
CC
GND pins must be connected. CKI is the clock input. This can come from the Internal
R/C oscillator, external, or a crystal oscillator (in conjunc­tion with CKO). See Oscillator Description section.
RESET is the master reset input. See Reset description section.
The device contains four bidirectional 8-bit I/O ports (C, G, L and F), where each individual bit may be independently configured as an input (Schmitt trigger inputs on ports L and G), output or TRI-STATE under program control. Three data memory address locations are allocated for each of these I/O ports. Each I/O port has two associated 8-bit memory mapped registers, the CONFIGURATION register and the output DATA register.A memory mapped address is also reserved for the input pins of each I/O port. (See the memory map for the various addresses associated with the I/O ports.) configurations. The DATA and CONFIGURATION regis­ters allow for each port bit to be individually configured under software control as shown below:
CONFIGURATION DATA Port Set-Up
Register Register
0 0 Hi-Z Input
0 1 Input with Weak Pull-Up 1 0 Push-Pull Zero Output 1 1 Push-Pull One Output
Port L is an 8-bit I/O port. All L-pins have Schmitt triggers on the inputs.
Port L supports the Multi-Input Wake Up feature on all eight pins. The 16-pin device does not have a full complement of Port L pins. The unavailable pins are not terminated. A read operation these unterminated pins are not terminated.A read operation these unterminated pins will return unpredictable values. To minimize current drain, the unavailable pins must be programmed as outputs.
Port G is an 8-bit port. Pin G0, G2–G5 are bi-directional I/O ports. Pin G6 is always a general purpose Hi-Z input. All pins have Schmitt Triggers on their inputs. Pin G1 serves as the
dedicated WDOUT WATCHDOG output with weak pullup if WATCHDOG feature is selected by the ECON register. The pin is a general purpose I/O if WATCHDOG feature is
Figure 5
shows the I/O port
(TRI-STATE Output)
not selected. If WATCHDOG feature is selected, bit 1 of the Port G configuration and data register does not have any effect on Pin G1 setup. Pin G7 is either input or output depending on the oscillator option selected. With the crystal oscillator option selected, G7 serves as the dedicated output pin for the CKO clock output. With the internal R/C or the external oscillator option selected, G7 serves as a general purpose Hi-Z input pin and is also used to bring the device out of HALTmode with a low to high transition on G7. There are two registers associated with Port G, a data register and a configuration register. Using these registers, each of the 5 I/O pins (G0, G2–G5) can be individually configured under software control.
Since G6 is an input only pin and G7 is the dedicated CKO clock output pin (crystal clock option) or general purpose input (R/C or external clock option), the associated bits in the data and configuration registers for G6 and G7 are used for special purpose functions as outlined below. Reading the G6 and G7 data bits will return zeroes.
The device will be placed in the HALT mode by writing a “1” to bit 7 of the Port G Data Register. Similarly the device will be placed in the IDLE mode by writing a “1” to bit 6 of the Port G Data Register.
Writing a “1” to bit 6 of the Port G Configuration Register enables the MICROWIRE/PLUS to operate with the alter­nate phase of the SK clock. The G7 configuration bit, if set high, enables the clock start up delay after HALT when the R/C clock configuration is used.
Config. Reg. Data Reg.
G7 CLKDLY HALT
G6 Alternate SK IDLE Port G has the following alternate features: G6 SI (MICROWIRE Serial Data Input) G5 SK (MICROWIRE Serial Clock) G4 SO (MICROWIRE Serial Data Output) G3 T1A (Timer T1 I/O) G2 T1B (Timer T1 Capture Input) G0 INTR (External Interrupt Input) Port G has the following dedicated functions: G7 CKO Oscillator dedicated output or general purpose
input G1 WDOUT WATCHDOG and/or CLock Monitor if WATCH-
DOG enabled, otherwise it is a general purpose I/O Port C is an 8-bit I/O port. The 40-pin device does not have
a full complement of Port C pins. The unavailable pins are not terminated. A read operation on these unterminated pins will return unpredictable values. Only the COP8SAC7 device contains Port C. The 20/28 pin devices do not offer Port C. On these devices, the associated Port C Data and Configu­ration registers should not be used.
Port F is an 8-bit I/O port. The 28-pin device does not have a full complement of Port F pins. The unavailable pins are not terminated. A read operation on these unterminated pins will return unpredictable values.
www.national.com 14
Page 15
COP8SA Family
5.0 Pin Descriptions (Continued)
FIGURE 5. I/O Port Configurations
DS012838-10
6.0 Functional Description
The architecture of the device is a modified Harvard archi­tecture. With the Harvard architecture, the program memory EPROM is separated from the data store memory (RAM). Both EPROM and RAM have their own separate addressing space with separate address buses. The architecture, though based on the Harvard architecture, permits transfer of data from EPROM to RAM.
6.1 CPU REGISTERS
There are six CPU registers: A is the 8-bit Accumulator Register PC is the 15-bit Program Counter Register
PU is the upper 7 bits of the program counter (PC) PL is the lower 8 bits of the program counter (PC)
B is an 8-bit RAM address pointer, which can be optionally post auto incremented or decremented.
X is an 8-bit alternate RAM address pointer, which can be optionally post auto incremented or decremented.
SP is the 8-bit stack pointer, which points to the subroutine/ interrupt stack (in RAM). With reset the SP is initialized to RAM address 02F Hex (devices with 64 bytes of RAM), or initialized to RAM address 06F Hex (devices with 128 bytes of RAM).
All the CPU registers are memory mapped with the excep­tion of the Accumulator (A) and the Program Counter (PC).
) cycle time.
C
DS012838-12
FIGURE 6. I/O Port Configurations—Output Mode
DS012838-11
FIGURE 7. I/O Port Configurations—Input Mode
Port D is an 8-bit output port that is preset high when RESET goes low. The user can tie two or more D port outputs (except D2) together in order to get a higher drive.
Note: Care must be exercised with the D2 pin operation. At RESET, the
external loads on this pin must ensure that the output voltages stay above 0.7 V keep the external loading on D2 to less than 1000 pF.
to prevent the chip from entering special modes. Also
CC
6.2 PROGRAM MEMORY
The program memory consists of 1024, 2048, or 4096 bytes of EPROM or ROM.
Table 1
shows the program memory sizes for the different devices. These bytes may hold pro­gram instructions or constant data (data tables for the LAID instruction, jump vectors for the JID instruction, and interrupt vectors for the VIS instruction). The program memory is addressed by the 15-bit program counter (PC). All interrupts in the device vector to program memory location 0FF Hex. The program memory reads 00 Hex in the erased state.
6.3 DATA MEMORY
The data memory address space includes the on-chip RAM and data registers, the I/O registers (Configuration, Data and Pin), the control registers, the MICROWIRE/PLUS SIO shift register, and the various registers, and counters associated with the timers (with the exception of the IDLE timer). Data memory is addressed directly by the instruction or indirectly by the B, X and SP pointers.
The data memory consists of 64 or 128 bytes of RAM.
1
shows the data memory sizes for the different devices.
Table
Fifteen bytes of RAM are mapped as “registers” at ad­dresses 0F0 to 0FE Hex. These registers can be loaded immediately, and also decremented and tested with the DRSZ (decrement register and skip if zero) instruction. The memory pointer registers X, SP and B are memory mapped into this space at address locations 0FC to 0FE Hex respec­tively, with the other registers (except 0FF) being available for general usage. Address location 0FF is reserved for future RAM expansion. If compatibility with future devices (with more RAM) is not desired, this location can be used as a general purpose RAM location.
The instruction set permits any bit in memory to be set, reset or tested. All I/O and registers (except A and PC) are
www.national.com15
Page 16
6.0 Functional Description (Continued)
memory mapped; therefore, I/O bits and register bits can be directly and individually set, reset and tested. The accumu­lator (A) bits can also be directly and individually tested.
RAM contents are undefined upon power-up.
COP8SA Family
TABLE 1. Program/Data Memory Sizes
Program Data User
Device Memory Memory Storage
(Bytes) (Bytes) (Bytes)
COP8SAA7 1024 64 8 COP8SAB7 2048 128 8 COP8SAC7 4096 128 8
6.4 ECON (CONFIGURATION) REGISTER
The format of the ECON register is as follows:
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
X POR SECURITY CKI 2 CKI 1 WATCH Reserved HALT
DOG
Bit 7 = x This is for factory test. The polarity is al-
ways 0.
Bit 6 = 1 Power-on reset enabled.
= 0 Power-on reset disabled.
Bit 5 = 1 Security enabled. EPROM read and write
are not allowed.
= 0 Security disabled. EPROM read and write
are allowed.
Bits 4, 3 = 0, 0 External CKI option selected. G7 is avail-
able as a HALT restart and/or general pur­pose input. CKI is clock input.
= 0, 1 R/C oscillator option selected. G7 is avail-
able as a HALT restart and/or general pur­pose input. CKI clock input. Internal R/C components are supplied for maximum R/C frequency.
= 1, 0 Crystal oscillator with on-chip crystal bias
resistor disabled. G7 (CKO) is the clock generator output to crystal/resonator.
= 1, 1 Crystal oscillator with on-chip crystal bias
resistor enabled. G7 (CKO) is the clock generator output to crystal/resonator.
Bit 2 = 1 WATCHDOG feature disabled. G1 is a
general purpose I/O.
= 0 WATCHDOG feature enabled. G1 pin is
WATCHDOG output with waek pullup. Bit 1 = Reserved. Bit 0 = 1 HALT mode disabled.
= 0 HALT mode enabled.
6.5 USER STORAGE SPACE IN EPROM
In addition to the ECON register, there are 8 bytes of EPROM available for “user information”. ECON and these 8 bytes are outside of the code area and are not protected by the security bit of the ECON register. Even when security is set, information in the 8-byte USER area is both read and write enabled allowing the user to read from and write into the area at all times while still protecting the code from unauthorized access.
Both ECON and USER area, 9 bytes total, are outside of the normal address range of the EPROM and can not be ac­cessed by the executing software. This allows for the stor­age of non-secured information. Typical uses are for storage of serial numbers, data codes, version numbers, copyright information, lot numbers, etc.
The following examples illustrate the declaration of ECON and the User information.
Syntax:
[label:] .sect econ, conf
.db value ;1 byte,
;configures options .db .endsect<user information>
;up to 8 bytes
Example: The following sets a value in the ECON register and User Identification for a COP8SAC728M7. The ECON bit values shown select options: Power-on enabled, Security disabled, Crystal oscillator with on-chip bias disabled, WATCHDOG enabled and HALT mode enabled.
.chip 8SAC .sect econ, conf .db 0x55 ;por, extal, wd, halt .db 'my v1.00' ;user data declaration .endsect ... .end start
Note: All programmers certified for programming this family of parts will
support programming of the CONFiguration section. Please contact National or your device programmer supplier for more information.
6.6 OTP SECURITY
The device has a security feature that, when enabled, pre­vents external reading of the OTP program memory. The security bit in the ECON register determines, whether secu­rity is enabled or disabled. If the security feature is disabled, the contents of the internal EPROM may be read.
If the security feature is enabled, then any attempt to externally read the contents of the EPROM will result in the value FF Hex being read from all program locations. Under no circumstances can a secured part be read. In
If security is being used, it is recommended that all other bits in the ECON register be programmed first. Then the security bit can be programmed.
www.national.com 16
Page 17
6.0 Functional Description (Continued)
6.7 RESET
The device is initialized when the RESET pin is pulled low or the On-chip Power-On Reset is enabled.
DS012838-13
FIGURE 8. Reset Logic
The following occurs upon initialization:
Port L: TRISTATE Port C: TRISTATE Port G: TRISTATE Port F: TRISTATE Port D: HIGH PC: CLEARED to 0000 PSW, CNTRL and ICNTRL registers: CLEARED SIOR: UNAFFECTED after RESET with power already
applied
RANDOM after RESET at power-on T1CNTRL: CLEARED Accumulator, Timer 1:
RANDOM after RESET with crystal clock option
(power already applied)
UNAFFECTED after RESET with R/C clock option
(power already applied)
RANDOM after RESET at power-on WKEN, WKEDG: CLEARED WKPND: RANDOM SP (Stack Pointer):
Initialized to RAM address 02F Hex (devices with
64 bytes of RAM), or initialized to
RAM address 06F Hex (devices with
128 bytes of RAM). B and X Pointers:
UNAFFECTED after RESET with power
already applied
RANDOM after RESET at power-on RAM:
UNAFFECTED after RESET with power already
applied
RANDOM after RESET at power-on WATCHDOG (if enabled):
The device comes out of reset with both the WATCHDOG logic and the Clock Monitor detector armed, with the WATCHDOG service window bits set and the Clock Monitor bit set. The WATCHDOG and Clock Monitor circuits are inhibited during reset. The WATCHDOG service window bits being initialized high default to the maximum WATCHDOG service window of 64k t being initialized high will cause a Clock Monitor error follow­ing reset if the clock has not reached the minimum specified
clock cycles. The Clock Monitor bit
C
frequency at the termination of reset. A Clock Monitor error will cause an active low error output on pin G1. This error output will continue until 16 t
–32 tCclock cycles following
C
the clock frequency reaching the minimum specified value, at which time the G1 output will go high.
6.7.1 External Reset
The RESET input when pulled low initializes the device. The RESET pin must be held low for a minimum of one instruc­tion cycle to guarantee a valid reset. During Power-Up ini­tialization, the user must ensure that the RESET pin is held low until the device is within the specified VCCvoltage. An R/C circuit on the RESET pin with a delay 5 times (5x) greater than the power supply rise time or 15 µs whichever is greater,is recommended. Reset should also be wide enough to ensure crystal start-up upon Power-Up.
RESET may also be used to cause an exit from the HALT mode.
Figure 9
RC>5x power supply rise time or 15 µs, whichever is greater.
.
DS012838-14
FIGURE 9. Reset Circuit Using External Reset
6.7.2 On-Chip Power-On Reset
The on-chip reset circuit is selected by a bit in the ECON register. When enabled, the device generates an internal reset as V
rises to a voltage level above 2.0V. The on-chip
CC
reset circuitry is able to detect both fast and slow rise times on V
CC(VCC
rise time between 10 ns and 50 ms).
Under no circumstances should the RESET pin be allowed to float. If the on-chip Power-On Reset feature is being used, RESET pin should be connected directly to V
. The output
CC
). At this time, the internal reset will be
C
generated. If the Power-On Reset feature is enabled, the internal reset
will not be turned off until the Idle timer underflows. The internal reset will perform the same functions as external reset. The user is responsible for ensuring that V
CC
is at the minimum level for the operating frequency within the 4096 t
. After the underflow, the logic is designed such that no
C
additional internal resets occur as long as V
CC
remains above 2.0V.
Note: Whilethe POR feature of theCOP8SAx was never intended tofunction
as a brownout detector, there are certain constraints of this block that the systemdesigner mustaddress to properlyrecover from a brownout condition. This is true regardless of whether the internal POR or the external reset feature is used.
A brownout condition is reached when V the minimum operating conditions of the device. The minimum guar­anteed operatingconditions are defined as V
= 2.7V@4 MHz, or VCC= 2.0V during HALT mode (or when CKI
V
CC
is stopped) operation. When using either the external reset or the POR feature to recover
from a brownout condition, V external reset must be applied whenever it goes below the minimum operating conditions as stated above.
CC
of the device goes below
CC
= 4.5V@10 MHzCKI,
CC
must be lowered to 0.25V or an
COP8SA Family
www.national.com17
Page 18
6.0 Functional Description (Continued)
The contents of data registers and RAM are unknown fol­lowing the on-chip reset.
COP8SA Family
6.8.1 Crystal Oscillator
The crystal Oscillator mode can be selected by programming ECON Bit 4 to 1. CKI is the clock input while G7/CKO is the clock generator output to the crystal.Anon-chip bias resistor connected between CKI and CKO can be enabled by pro­gramming ECON Bit 3 to 1 with the crystal oscillator option selection. The value of the resistor is in the range of 0.5M to 2M (typically 1.0M).
Table 3
shows the component values required for various standard crystal values. Resistor R2 is only used when the on-chip bias resistor is disabled.
12
shows the crystal oscillator connection diagram.
Figure
TABLE 3. Crystal Oscillator Configuration,
T
= 25˚C, VCC=5V
A
R1 (kΩ)R2(MΩ) C1 (pF) C2 (pF) CKI Freq. (MHz)
0 1 30 30 15 0 1 32 32 10 0 1 45 30–36 4
5.6 1 100 100–156 0.455
6.8.2 External Oscillator
Figure 13
shows the external oscillator connec-
tion diagram.
DS012838-15
FIGURE 10. Reset Timing (Power-On Reset Enabled)
with V
Tied to RESET
CC
DS012838-16
FIGURE 11. Reset Circuit Using Power-On Reset
6.8 OSCILLATOR CIRCUITS
There are four clock oscillator options available: Crystal Oscillator with or without on-chip bias resistor, R/C Oscillator with on-chip resistor and capacitor, and External Oscillator. The oscillator feature is selected by programming the ECON register, which is summarized in
Table 2
.
TABLE 2. Oscillator Option
ECON4 ECON3 Oscillator Option
0 0 External Oscillator 1 0 Crystal Oscillator without Bias Resistor 0 1 R/C Oscillator 1 1 Crystal Oscillator with Bias Resistor
6.8.3 R/C Oscillator
The R/C Oscillator mode can be selected by programming ECON Bit 3 to 1 and ECON Bit 4 to 0. In R/C oscillation mode, CKI is left floating, while G7/CKO is available as a general purpose input G7 and/or HALT control. The R/C controlled oscillator has on-chip resistor and capacitor for maximum R/C oscillator frequency operation. The maximum frequency is 6 MHz
±
35% for VCCbetween 4.5V to 5.5V and temperature range of −40˚C to +85˚C. For max fre­quency operation, the CKI pin should be left floating. For lower frequencies, an external capacitor should be con­nected between CKI and either V
or GND. Immunity of the
CC
R/C oscillator to external noise can be improved by connect­ing one half the external capacitance to V
and one half to
CC
GND. PC board trace length on the CKI pin should be kept as short as possible.
Table 4
shows the oscillator frequency as a function of approximate external capacitance on the CKI pin.
Figure 14
shows the R/C oscillator configuration.
TABLE 4. R/C Oscillator Configuration,
−40˚C to +85˚C, V OSC Freq. Variation of
External Capacitor R/C OSC Freq Instr. Cycle
(pF) (MHz) (µs)
0 6 1.667 13 4 2.5 62 2 5.0
120 1 10
5600 32 kHz 312.5
= 4.5V to 5.5V,
CC
±
35%
www.national.com 18
Page 19
6.0 Functional Description (Continued)
COP8SA Family
With On-Chip Bias Resistor
DS012838-17
Without On-Chip Bias Resistor
DS012838-18
FIGURE 12. Crystal Oscillator
DS012838-19
FIGURE 13. External Oscillator
DS012838-20
For operation at lower than maximum R/C oscillator frequency.
DS012838-21
For operation at maximum R/C oscillator frequency.
FIGURE 14. R/C Oscillator
www.national.com19
Page 20
6.0 Functional Description (Continued)
6.9 CONTROL REGISTERS
CNTRL Register (Address X'00EE)
T1C3 T1C2 T1C1 T1C0 MSEL IEDG SL1 SL0
COP8SA Family
Bit 7 Bit 0
T1C3 Timer T1 mode control bit T1C2 Timer T1 mode control bit T1C1 Timer T1 mode control bit T1C0 Timer T1 Start/Stop control in timer
modes 1 and 2, T1 Underflow Interrupt Pending Flag in timer mode 3
MSEL Selects G5 and G4 as MICROWIRE/PLUS
signals SK and SO respectively
IEDG External interrupt edge polarity select
(0 = Rising edge, 1 = Falling edge)
SL1 & SL0 Select the MICROWIRE/PLUS clock divide
by (00 = 2, 01 = 4, 1x = 8)
PSW Register (Address X'00EF)
HC C T1PNDA T1ENA EXPND BUSY EXEN GIE
Bit 7 Bit 0
The PSW register contains the following select bits:
HC Half Carry Flag C Carry Flag T1PNDA Timer T1 Interrupt Pending Flag (Autoreload
RA in mode 1, T1 Underflow in Mode 2, T1A capture edge in mode 3)
T1ENA Timer T1 Interrupt Enable for Timer Underflow
or T1A Input capture edge EXPND External interrupt pending BUSY MICROWIRE/PLUS busy shifting flag EXEN Enable external interrupt GIE Global interrupt enable (enables interrupts)
The Half-Carry flag is also affected by all the instructions that affect the Carry flag. The SC (Set Carry) and R/C (Reset Carry) instructions will respectively set or clear both the carry flags. In addition to the SC and R/C instructions, ADC, SUBC, RRC and RLC instructions affect the Carry and Half Carry flags.
ICNTRL Register (Address X'00E8)
Reserved LPEN T0PND T0EN µWPND µWEN T1PNDB T1ENB Bit 7 Bit 0
The ICNTRL register contains the following bits:
Reserved This bit is reserved and should to zero LPEN L Port Interrupt Enable (Multi-Input Wakeup/
Interrupt) T0PND Timer T0 Interrupt pending T0EN Timer T0 Interrupt Enable (Bit 12 toggle) µWPND MICROWIRE/PLUS interrupt pending µWEN Enable MICROWIRE/PLUS interrupt T1PNDB Timer T1 Interrupt Pending Flag for T1B cap-
ture edge
T1ENB Timer T1 Interrupt Enable for T1B Input cap-
ture edge
7.0 Timers
The device contains a very versatile set of timers (T0, T1). TimerT1 and associated autoreload/capture registers power up containing random data.
7.1 TIMER T0 (IDLE TIMER)
The device supports applications that require maintaining real time and low power with the IDLE mode. This IDLE mode support is furnished by the IDLE timer T0. The Timer T0 runs continuously at the fixed rate of the instruction cycle clock, t which is a count down timer.
The Timer T0 supports the following functions:
•
•
•
•
The IDLE Timer T0 can generate an interrupt when the twelfth bit toggles. This toggle is latched into the T0PND pending flag, and will occur every 4.096 ms at the maximum clock frequency (t interrupt from the twelfth bit of Timer T0 to be enabled or disabled. Setting T0EN will enable the interrupt, while reset­ting it will disable the interrupt.
7.2 TIMER T1
One of the main functions of a microcontroller is to provide timing and counting capability for real-time control tasks. The COP8 family offers a very versatile 16-bit timer/counter structure, and two supporting 16-bit autoreload/capture reg­isters (R1A and R1B), optimized to reduce software burdens in real-time control applications.Thetimerblockhas two pins associated with it, T1A and T1B. Pin T1A supports I/O re­quired by the timer block, while pin T1B is an input to the timer block.
The timer block has three operating modes: Processor Inde­pendent PWM mode, External Event Counter mode, and Input Capture mode.
The control bitsT1C3,T1C2,and T1C1 allow selection of the different modes of operation.
7.2.1 Mode 1. Processor Independent PWM Mode
One of the timer’s operating modes is the Processor Inde­pendent PWM mode. In this mode, the timer generates a “Processor Independent” PWM signal because once the timer is setup, no more action is required from the CPU which translates to less software overhead and greater throughput. The user software services the timer block only when the PWM parameters require updating. This capability is provided by the fact that the timer has two separate 16-bit reload registers. One of the reload registers contains the “ON” timer while the other holds the “OFF” time. By contrast, a microcontroller that has only a single reload register re­quires an additional software to update the reload value (alternate between the on-time/off-time).
. The user cannot read or write to the IDLETimerT0,
C
Exit out of the Idle Mode (See Idle Mode description) WATCHDOG logic (See WATCHDOG description) Start up delay out of the HALT mode Timing the width of the internal power-on-reset
= 1 µs). A control flag T0EN allows the
C
www.national.com 20
Page 21
7.0 Timers (Continued)
In this mode, the timer T1 counts down at a fixed rate of t Upon every underflow the timer is alternately reloaded with the contents of supporting registers, R1A and R1B. The very first underflow of the timer causes the timer to reload from the register R1A. Subsequent underflows cause the timer to be reloaded from the registers alternately beginning with the register R1B.
Figure 15
shows a block diagram of the timer in PWM mode.
COP8SA Family
Underflows from the timer are alternately latched into two pending flags, T1PNDA and T1PNDB. The user must reset these pending flags under software control. Two control enable flags, T1ENA and T1ENB, allow the interrupts from the timer underflow to be enabled or disabled. Setting the
.
C
timer enable flag T1ENA will cause an interrupt when a timer underflow causes the R1A register to be reloaded into the timer. Setting the timer enable flag T1ENB will cause an interrupt when a timer underflow causes the R1B register to be reloaded into the timer. Resetting the timer enable flags will disable the associated interrupts.
FIGURE 15. Timer in PWM Mode
7.2.2 Mode 2. External Event Counter Mode
This mode is quite similar to the processor independent PWM mode described above. The main difference is that the timer,T1, is clocked by the input signal from the T1Apin. The T1 timer control bits, T1C3, T1C2 and T1C1 allow the timer to be clocked either on a positive or negative edge from the T1A pin. Underflows from the timer are latched into the T1PNDA pending flag. Setting the T1ENA control flag will cause an interrupt when the timer underflows.
In this mode the input pin T1B can be used as an indepen­dent positive edge sensitive interrupt input if the T1ENB control flag is set. The occurrence of a positive edge on the T1B input pin is latched into the T1PNDB flag.
Figure 16
shows a block diagram of the timer in External
Event Counter mode.
Note: The PWM output is not available in this mode since the T1A pin is
being used as the counter input clock.
DS012838-22
DS012838-23
FIGURE 16. Timer in External Event Counter Mode
www.national.com21
Page 22
7.0 Timers (Continued)
7.2.3 Mode 3. Input Capture Mode
The device can precisely measure external frequencies or time external events by placing the timer block, T1, in the input capture mode. In this mode, the reload registers serve
COP8SA Family
In this mode, the timer T1 is constantly running at the fixed t rate. The two registers, R1A and R1B, act as capture regis­ters. Each register acts in conjunction with a pin.Theregister R1A acts in conjunction with the T1A pin and the register R1B acts in conjunction with the T1B pin.
The timer value gets copied over into the register when a trigger event occurs on its corresponding pin. Control bits, T1C3, T1C2 and T1C1, allow the trigger events to be speci-
The trigger conditions can also be programmed to generate interrupts. The occurrence of the specified trigger condition on the T1A and T1B pins will be respectively latched into the pending flags, T1PNDA and T1PNDB. The control flag T1ENA allows the interrupt on T1A to be either enabled or disabled. Setting the T1ENA flag enables interrupts to be generated when the selected trigger condition occurs on the T1A pin. Similarly, the flag T1ENB controls the interrupts from the T1B pin.
C
enabled with the T1ENA control flag. When a T1A interrupt occurs in the Input Capture mode, the user must check both the T1PNDA and T1C0 pending flags in order to determine whether a T1A input capture or a timer underflow (or both) caused the interrupt.
Figure 17
shows a block diagram of the timer in Input Cap-
ture mode.
FIGURE 17. Timer in Input Capture Mode
www.national.com 22
DS012838-24
Page 23
7.0 Timers (Continued)
7.3 TIMER CONTROL FLAGS
T1PNDA Timer Interrupt Pending Flag T1ENA Timer Interrupt Enable Flag
The control bits and their functions are summarized below.
T1C3 Timer mode control T1C2 Timer mode control T1C1 Timer mode control
T1PNDB Timer Interrupt Pending Flag T1ENB Timer Interrupt Enable Flag
T1C0 Timer Start/Stop control in Modes 1 and 2 (Pro-
cessor Independent PWM and External Event Counter), where 1 = Start, 0 = Stop Timer Underflow Interrupt Pending Flag in Mode 3 (Input Capture)
The timer mode control bits (T1C3, T1C2 and T1C1) are detailed below:
COP8SA Family
1 = Timer Interrupt Enabled 0 = Timer Interrupt Disabled
1 = Timer Interrupt Enabled 0 = Timer Interrupt Disabled
Mode T1C3 T1C2 T1C1 Description
1 0 1 PWM: T1A Toggle Autoreload RA Autoreload RB t
1
1 0 0 PWM: No T1A
Toggle
0 0 0 External Event
2
0 0 1 External Event
Counter
Counter
0 1 0 Captures: Pos. T1A Edge Pos. T1B Edge t
T1A Pos. Edge or Timer T1B Pos. Edge Underflow
1 1 0 Captures: Pos. T1A Neg. T1B t
T1A Pos. Edge Edge or Timer Edge
3
0 1 1 Captures: Neg. T1A Neg. T1B t
T1B Neg. Edge Underflow
T1A Neg. Edge Edge or Timer Edge T1B Neg. Edge Underflow
1 1 1 Captures: Neg. T1A Neg. T1B t
T1A Neg. Edge Edge or Timer Edge T1B Neg. Edge Underflow
Interrupt A
Source
Interrupt B
Source
Autoreload RA Autoreload RB
Timer
Pos. T1B Edge Pos. T1A
Underflow Timer
Pos. T1B Edge Pos. T1A
Underflow
Timer
Counts On
C
t
C
Edge
Edge
C
C
C
C
www.national.com23
Page 24
8.0 Power Save Modes
Today, the proliferation of battery-operated based applica­tions has placed new demands on designers to drive power consumption down. Battery-operated systems are not the only type of applications demanding low power. The power budget constraints are also imposed on those consumer/
COP8SA Family
industrial applications where well regulated and expensive power supply costs cannot be tolerated. Such applications rely on low cost and low power supply voltage derived di­rectly from the “mains” by using voltage rectifier and passive components. Low power is demanded even in automotive applications, due to increased vehicle electronics content. This is required to ease the burden from the car battery. Low power 8-bit microcontrollers supply the smarts to control battery-operated, consumer/industrial, and automotive appli­cations.
The COP8SAx devices offer system designers a variety of low-power consumption features that enable them to meet the demanding requirements of today’s increasing range of low-power applications. These features include low voltage operation, low current drain, and power saving features such as HALT, IDLE, and Multi-Input wakeup (MIWU).
The devices offer the user two power save modes of opera­tion: HALT and IDLE. In the HALT mode, all microcontroller activities are stopped. In the IDLE mode, the on-board os­cillator circuitry and timer T0 are active but all other micro­controller activities are stopped. In either mode, all on-board RAM, registers, I/O states, and timers (with the exception of T0) are unaltered.
Clock Monitor if enabled can be active in both modes.
8.1 HALT MODE
The device can be placed in the HALT mode by writing a “1” to the HALT flag (G7 data bit). All microcontroller activities, including the clock and timers, are stopped. The WATCH­DOG logic on the device is disabled during the HALT mode. However, the clock monitor circuitry, if enabled, remains active and will cause the WATCHDOG output pin (WDOUT) to go low. If the HALT mode is used and the user does not want to activate the WDOUT pin, the Clock Monitor should be disabled after the device comes out of reset (resetting the Clock Monitor control bit with the first write to the WDSVR register). In the HALT mode, the power requirements of the device are minimal and the applied voltage (V decreased to V machine.
The device supports three different ways of exiting the HALT mode. The first method of exiting the HALT mode is with the Multi-Input Wakeup feature on Port L. The second method is
= 2.0V) without altering the state of the
r(Vr
) may be
CC
with a low to high transition on the CKO (G7) pin. This method precludes the use of the crystal clock configuration (since CKO becomes a dedicated output), and so may only be used with an R/C clock configuration. The third method of exiting the HALT mode is by pulling the RESET pin low.
Since a crystal or ceramic resonator may be selected as the oscillator, the Wakeup signal is not allowed to start the chip running immediately since crystal oscillators and ceramic resonators have a delayed start up time to reach full ampli­tude and frequency stability. The IDLE timer is used to generate a fixed delay to ensure that the oscillator has indeed stabilized before allowing instruction execution. In this case, upon detecting a valid Wakeup signal, only the oscillator circuitry is enabled. The IDLE timer is loaded with a value of 256 and is clocked with the t clock. The t
clock is derived by dividing the oscillator clock
C
instruction cycle
C
down by a factor of 10. The Schmitt trigger following the CKI inverter on the chip ensures that the IDLE timer is clocked only when the oscillator has a sufficiently large amplitude to meet the Schmitt trigger specifications. This Schmitt trigger is not part of the oscillator closed loop. The start-up time-out from the IDLE timer enables the clock signals to be routed to the rest of the chip.
If an R/C clock option is being used, the fixed delay is introduced optionally. A control bit, CLKDLY, mapped as configuration bit G7, controls whether the delay is to be introduced or not. The delay is included if CLKDLY is set, and excluded if CLKDLY is reset. The CLKDLYbit is cleared on reset.
If the device is placed in the HALT mode, with the R/C oscillator selected, the clock input pin (CKI) is forced to a logic high internally. With the crystal or external oscillator the CKI pin is TRI-STATE.
www.national.com 24
Page 25
8.0 Power Save Modes (Continued)
FIGURE 18. Wakeup from HALT
8.2 IDLE MODE
The device is placed in the IDLE mode by writing a “1” to the IDLE flag (G6 data bit). In this mode, all activities, except the associated on-board oscillator circuitry and the IDLE Timer T0, are stopped.
As with the HALT mode, the device can be returned to normal operation with a reset, or with a Multi-Input Wakeup from the L Port. Alternately, the microcontroller resumes normal operation from the IDLE mode when the twelfth bit (representing 4.096 ms at internal clock frequency of 10 MHz, t
This toggle condition of the twelfth bit of the IDLE TimerT0 is latched into the T0PND pending flag.
The user has the option of being interrupted with a transition on the twelfth bit of the IDLE Timer T0. The interrupt can be enabled or disabled via the T0EN control bit. Setting the T0EN flag enables the interrupt and vice versa.
= 1 µs) of the IDLE Timer toggles.
C
COP8SA Family
DS012838-25
The user can enter the IDLE mode with the Timer T0 inter­rupt enabled. In this case, when the T0PND bit gets set, the device will first execute the Timer T0 interrupt service routine and then return to the instruction following the “Enter Idle Mode” instruction.
Alternatively, the user can enter the IDLE mode with the IDLE TimerT0 interrupt disabled. In this case, the device will resume normal operation with the instruction immediately following the “Enter IDLE Mode” instruction.
Note: It is necessary to program two NOP instructions following both the set
HALT mode and set IDLE mode instructions. These NOP instructions are necessary to allow clock resynchronization following the HALT or IDLE modes.
FIGURE 19. Wakeup from IDLE
DS012838-26
www.national.com25
Page 26
8.0 Power Save Modes (Continued)
8.3 MULTI-INPUT WAKEUP
The Multi-Input Wakeup feature is used to return (wakeup) the device from either the HALT or IDLE modes. Alternately Multi-Input Wakeup/Interrupt feature may also be used to
COP8SA Family
generate up to 8 edge selectable external interrupts.
Figure 20
The Multi-Input Wakeup feature utilizes the L Port. The user selects which particular L port bit (or combination of L Port bits) will cause the device to exit the HALT or IDLE modes. The selection is done through the register WKEN. The reg­ister WKEN is an 8-bit read/write register, which contains a control bit for every L port bit. Setting a particular WKEN bit enables a Wakeup from the associated L port pin.
The user can select whether the trigger condition on the selected L Port pin is going to be either a positive edge (low to high transition) or a negative edge (high to low transition). This selection is made via the register WKEDG, which is an 8-bit control register with a bit assigned to each L Port pin. Setting the control bit will select the trigger condition to be a negative edge on that particular L Port pin. Resetting the bit selects the trigger condition to be a positive edge. Changing an edge select entails several steps in order to avoid a Wakeup condition as a result of the edge change. First, the associated WKEN bit should be reset, followed by the edge select change in WKEDG. Next, the associated WKPND bit should be cleared, followed by the associated WKEN bit being re-enabled.
shows the Multi-Input Wakeup logic.
An example may serve to clarify this procedure. Suppose we wish to change the edge select frompositive(lowgoinghigh) to negative (high going low) for L Port bit 5, where bit 5 has previously been enabled for an input interrupt. The program would be as follows:
RBIT 5, WKEN ; Disable MIWU SBIT 5, WKEDG ; Change edge polarity RBIT 5, WKPND ; Reset pending flag SBIT 5, WKEN ; Enable MIWU
If the L port bits have been used as outputs and then changed to inputs with Multi-Input Wakeup/Interrupt,asafety procedure should also be followed to avoid wakeup condi­tions. After the selected L port bits have been changed from output to input but before the associated WKEN bits are enabled, the associated edge select bits in WKEDG should be set or reset for the desired edge selects, followed by the associated WKPND bits being cleared.
This same procedure should be used following reset, since the L port inputs are left floating as a result of reset.
The occurrence of the selected trigger condition for Multi-Input Wakeup is latched into a pending register called WKPND. The respective bits of the WKPND register will be set on the occurrence of the selected trigger edge on the corresponding Port L pin. The user has the responsibility of clearing these pending flags. Since WKPND is a pending register for the occurrence of selected wakeup conditions, the device will not enter the HALT mode if any Wakeup bit is both enabled and pending. Consequently, the user must clear the pending flags before attempting to enter the HALT mode.
WKEN and WKEDG are all read/write registers, and are cleared at reset. WKPND register contains random value after reset.
FIGURE 20. Multi-Input Wake Up Logic
www.national.com 26
DS012838-27
Page 27
9.0 Interrupts
9.1 INTRODUCTION
All interrupts force a branch to location 00FF Hex in program memory. The VIS instruction may be used to vector to the appropriate service routine from location 00FF Hex.
The Software trap has the highest priority while the default VIS has the lowest priority.
Each of the six maskable inputs has a fixed arbitration ranking and vector.
Figure 21
shows the Interrupt Block Diagram.
COP8SA Family
FIGURE 21. Interrupt Block Diagram
DS012838-28
www.national.com27
Page 28
9.0 Interrupts (Continued)
9.2 MASKABLE INTERRUPTS
All interrupts other than the Software Trap are maskable. Each maskable interrupt has an associated enable bit and pending flag bit. The pending bit is set to 1 when the interrupt
COP8SA Family
Amaskableinterruptconditiontriggers an interrupt under the following conditions:
1. The enable bit associated with that interrupt is set.
2. The GIE bit is set.
3. The device is not processing a non-maskable interrupt. (If a non-maskable interrupt is being serviced, a maskable interrupt must wait until that service routine is completed.)
An interrupt is triggered only when all of these conditions are met at the beginning of an instruction. If different maskable interrupts meet these conditions simultaneously, the highest priority interrupt will be serviced first, and the other pending interrupts must wait.
Upon Reset, all pending bits, individual enable bits, and the GIE bit are reset to zero. Thus, a maskable interrupt condi­tion cannot trigger an interrupt until theprogramenablesitby setting both the GIE bit and the individual enable bit. When enabling an interrupt, the user should consider whether or not a previously activated (set) pending bit should be ac­knowledged. If, at the time an interrupt is enabled, any previous occurrences of the interrupt should be ignored, the associated pending bit must be reset to zero prior to en­abling the interrupt. Otherwise, the interrupt may be simply enabled; if the pending bit is already set, it will immediately trigger an interrupt. A maskable interrupt is active if its asso­ciated enable and pending bits are set.
An interrupt is an asychronous event which may occur be­fore, during, or after an instruction cycle. Any interrupt which occurs during the execution of an instruction is not acknowl­edged until the start of the next normally executed instruction is to be skipped, the skip is performed before the pending interrupt is acknowledged.
At the start of interrupt acknowledgment, the following ac­tions occur:
1. The GIE bit is automatically reset to zero, preventing any subsequent maskable interrupt from interrupting the cur­rent service routine. This feature prevents one maskable interrupt from interrupting another one being serviced.
2. The address of the instruction about to be executed is pushed onto the stack.
3. The program counter (PC) is loaded with 00FF Hex, causing a jump to that program memory location.
The device requires seven instruction cycles to perform the actions listed above.
If the user wishes to allow nested interrupts, the interrupts service routine may set the GIE bit to 1 by writing to the PSW register,andthusallowother maskable interrupts to interrupt the current service routine. If nested interrupts are allowed, caution must be exercised. The user must write the program in such a way as to prevent stack overflow, loss of saved context information, and other unwanted conditions.
The interrupt service routine stored at location 00FF Hex should use the VIS instruction to determine the cause of the
interrupt, and jump to the interrupt handling routine corre­sponding to the highest priority enabled and active interrupt. Alternately, the user may choose to poll all interrupt pending and enable bits to determine the source(s) of the interrupt. If more than one interrupt is active, the user’s program must decide which interrupt to service.
Within a specific interrupt service routine, the associated pending bit should be cleared. This is typically done as early as possible in the service routine in order to avoid missing the next occurrence of the same type of interrupt event. Thus, if the same event occursasecondtime,evenwhilethe first occurrence is still being serviced, the second occur­rence will be serviced immediately upon return from the current interrupt routine.
An interrupt service routine typically ends with an RETI instruction. This instruction sets the GIE bit back to 1, pops the address stored on the stack, and restores that address to the program counter. Program execution then proceeds with the next instruction that would have been executed had there been no interrupt. If there are any valid interrupts pending, the highest-priority interrupt is serviced immedi­ately upon return from the previous interrupt.
9.3 VIS INSTRUCTION
The general interrupt service routine, which starts at address 00FF Hex, must be capable of handling all types of inter­rupts. The VIS instruction, together with an interrupt vector table, directs the device to the specific interrupt handling routine based on the cause of the interrupt.
VIS is a single-byte instruction, typically used at the very beginning of the general interrupt service routine at address 00FF Hex, or shortly after that point, just after the code used for context switching. The VIS instruction determines which enabled and pending interrupt has the highest priority, and causes an indirect jump to the address corresponding to that interrupt source. The jump addresses (vectors) for all pos­sible interrupts sources are stored in a vector table.
The vector table may be as long as 32 bytes (maximum of 16 vectors) and resides at the top of the 256-byte block con­taining the VIS instruction. However, if the VIS instruction is at the very top of a 256-byte block (such as at 00FF Hex), the vector table resides at the top of the next 256-byte block. Thus, if the VIS instruction is located somewhere between 00FF and 01DF Hex (the usual case), the vector table is located between addresses 01E0 and 01FF Hex. If the VIS instruction is located between 01FF and 02DF Hex, then the vector table is located between addresses 02E0 and 02FF Hex, and so on.
Each vector is 15 bits long and points to the beginning of a specific interrupt service routine somewhere in the 32 kbyte memory space. Each vector occupies two bytes of the vector table, with the higher-order byte at the lower address. The vectors are arranged in order of interrupt priority. The vector of the maskable interrupt with the lowest rank is located to 0yE0 (higher-order byte) and 0yE1 (lower-order byte). The next priority interrupt is located at 0yE2 and 0yE3, and so forth in increasing rank. The Software Trap has the highest rank and its vector is always located at 0yFE and 0yFF. The number of interrupts which can become active defines the size of the table.
Table 5
shows the types of interrupts, the interrupt arbitration ranking, and the locations of the corresponding vectors in the vector table.
The vector table should be filled by the user with the memory locations of the specific interrupt service routines. For ex-
www.national.com 28
Page 29
9.0 Interrupts (Continued)
ample, if the Software Trap routine is located at 0310 Hex, then the vector location 0yFE and -0yFF should contain the data 03 and 10 Hex, respectively. When a Software Trap interrupt occurs and the VIS instruction is executed, the program jumps to the address specified in the vector table.
The interrupt sources in the vector table are listed in order of rank, from highest to lowest priority. If two or more enabled and pending interrupts are detected at the same time, the one with the highest priority is serviced first. Upon return from the interrupt service routine, the next highest-level pending interrupt is serviced.
If the VIS instruction is executed, but no interrupts are en­abled and pending, the lowest-priority interrupt vector is used, and a jump is made to the corresponding address in the vector table. This is an unusual occurrence, and may be the result of an error. It can legitimately result from a change in the enable bits or pending flags prior to the execution of the VIS instruction, such as executing a single cycle instruc­tion which clears an enable flag at the same time that the pending flag is set. It can also result, however, from inad­vertent execution of the VIS command outside of the context of an interrupt.
The default VIS interrupt vector can be useful for applica­tions in which time critical interrupts can occur during the servicing of another interrupt. Rather than restoring the pro-
gram context (A, B, X, etc.) and executing the RETI instruc­tion, an interrupt service routine can be terminated by return­ing to the VIS instruction. In this case, interrupts will be serviced in turn until no further interrupts are pending and the default VIS routine is started. After testing the GIE bit to ensure that execution is not erroneous, the routine should restore the program context and execute the RETI to return to the interrupted program.
This technique can save up to fifty instruction cycles (t
c
), or more, (50 µs at 10 MHz oscillator) of latency for pending interrupts with a penalty of fewer than ten instruction cycles if no further interrupts are pending.
COP8SA Family
TABLE 5. Interrupt Vector Table
Arbitration Vector (Note 20)
Ranking Source Description Address
(Hi-Low Byte)
(1) Highest Software INTR Instruction 0yFE–0yFF (2) Reserved Future 0yFC–0yFD (3) External G0 0yFA–0yFB (4) Timer T0 Underflow 0yF8–0yF9 (5) Timer T1 T1A/Underflow 0yF6–0yF7 (6) Timer T1 T1B 0yF4–0yF5 (7) MICROWIRE/PLUS BUSY Low 0yF2–0yF3 (8) Reserved Future 0yF0–0yF1 (9) Reserved Future 0yEE–0yEF (10) Reserved Future 0yEC–0yED (11) Reserved Future 0yEA–0yEB (12) Reserved Future 0yE8–0yE9 (13) Reserved Future 0yE6–0yE7 (14) Reserved Future 0yE4–0yE5 (15) Port L/Wakeup Port L Edge 0yE2–0yE3 (16) Lowest Default VIS Instruction 0yE0–0yE1
Execution without any interrupts
Note 20: y is a variable which represents the VIS block. VIS and the vector table must be located in the same 256-byte block except if VIS is located at the last address of a block. In this case, the table must be in the next block.
www.national.com29
Page 30
9.0 Interrupts (Continued)
9.3.1 VIS Execution
When the VIS instruction is executed it activates the arbitra­tion logic. The arbitration logic generates an even number between E0 and FE (E0, E2, E4, E6 etc...) depending on
COP8SA Family
which active interrupt has the highest arbitration ranking at the time of the 1st cycle of VIS is executed. For example, if the software trap interrupt is active, FE is generated. If the external interrupt is active and the software trap interrupt is not, then FA is generated and so forth. If the only active interrupt is software trap, than E0 is generated. This number replaces the lower byte of the PC. The upper byte of the PC
remains unchanged. The new PC is therefore pointing to the vector of the active interrupt with the highest arbitration ranking. This vector is read from program memory and placed into the PC which is now pointed to the 1st instruction of the service routine of the active interrupt with the highest arbitration ranking.
Figure 22
instruction. tion.
The non-maskable interrupt pending flag is cleared by the RPND (Reset Non-Maskable Pending Bit) instruction (under certain conditions) and upon RESET.
illustrates the different steps performed by the VIS
Figure 23
shows a flowchart for the VIS instruc-
FIGURE 22. VIS Operation
DS012838-29
www.national.com 30
Page 31
9.0 Interrupts (Continued)
COP8SA Family
FIGURE 23. VIS Flowchart
DS012838-30
www.national.com31
Page 32
9.0 Interrupts (Continued)
Programming Example: External Interrupt
PSW =00EF CNTRL =00EE
COP8SA Family
WAIT: JP WAIT ; Wait for external interrupt
SERVICE: ; Interrupt Service Routine
RBIT 0,PORTGC RBIT 0,PORTGD ; G0 pin configured Hi-Z SBIT IEDG, CNTRL ; Ext interrupt polarity; falling edge SBIT GIE, PSW ; Set the GIE bit SBIT EXEN, PSW ; Enable the external interrupt
. . . .=0FF ; The interrupt causes a VIS ; branch to address 0FF
;The VIS causes a branch to
;interrupt vector table . . . .=01FA ; Vector table (within 256 byte .ADDRW SERVICE ; of VIS inst.) containing the ext
;interrupt service routine . . .
RBIT, EXPND, PSW ; Reset ext interrupt pend. bit . . . RET ; Return, set the GIE bit
www.national.com 32
Page 33
9.0 Interrupts (Continued)
9.4 NON-MASKABLE INTERRUPT
9.4.1 Pending Flag
There is a pending flag bit associated with the non-maskable interrupt, called STPND. This pending flag is not memory-mapped and cannot be accessed directly by the software.
The pending flag is reset to zero when a device Reset occurs. When the non-maskable interrupt occurs, the asso­ciated pending bit is set to 1. The interrupt service routine should contain an RPND instruction to reset the pending flag to zero. The RPND instruction always resets the STPND flag.
9.4.2 Software Trap
If the program counter incorrectly points to a memory loca­tion beyond the available program memory space, the non-existent or unused memory location returns zeroes which is interpreted as the INTR instruction.
If the stack is popped beyond the allowed limit (address 02F or 06F Hex), a Software Trap is triggered.
A Software Trap can be triggered by a temporary hardware condition such as a brownout or power supply glitch.
The Software Trap has the highest priority of all interrupts. When a Software Trapoccurs,theSTPNDbitisset.The GIE bit is not affected and the pending bit (not accessible by the user) is used to inhibit other interrupts and to direct the program to the ST service routine with the VIS instruction. Nothing can interrupt a Software Trap service routine except for another Software Trap. The STPND can be reset only by the RPND instruction or a chip Reset.
The Software Trap indicates an unusual or unknown error condition. Generally, returning to normal execution at the point where the Software Trap occurred cannot be done reliably.Therefore, the Software Trap service routine should reinitialize the stack pointer and perform a recovery proce­dure that restarts the software at some known point, similar to a device Reset, but not necessarily performing all the same functions as a device Reset. The routine must also execute the RPND instruction to reset the STPND flag. Otherwise, all other interrupts will be locked out. To the extent possible, the interrupt routine should record or indi­cate the context of the device so that the cause of the Software Trap can be determined.
If the user wishes to return to normal execution from the point at which the Software Trap was triggered, the user must first execute RPND, followed by RETSK rather than RETI or RET. This is because the return address stored on the stack is the address of the INTR instruction that triggered the interrupt. The program must skip that instruction in order to proceed with the next one. Otherwise, an infinite loop of Software Traps and returns will occur.
COP8SA Family
Programming a return to normal execution requires careful consideration. If the Software Trap routine is interrupted by another Software Trap, the RPND instruction in the service routine for the second Software Trap will reset the STPND flag; upon return to the first Software Trap routine, the STPND flag will have the wrong state. This will allow maskable interrupts to be acknowledged during the servicing of the first SoftwareTrap.Toavoid problems such as this, the user program should contain the Software Trap routine to perform a recovery procedure rather than a return to normal execution.
Under normal conditions, the STPND flag is reset by a RPND instruction in the Software Trap service routine. If a programming error or hardware condition (brownout, power supply glitch, etc.) sets the STPND flag without providing a way for it to be cleared, all other interrupts will be locked out. To alleviate this condition, the user can use extra RPND instructions in the main program and in the WATCHDOG service routine (if present). There is no harm in executing extra RPND instructions in these parts of the program.
9.5 PORT L INTERRUPTS
Port L provides the user with an additional eight fully select­able, edge sensitive interrupts which are all vectored into the same service subroutine.
The interrupt from Port L shares logic with the wake up circuitry. The register WKEN allows interrupts from Port L to be individually enabled or disabled. The register WKEDG specifies the trigger condition to be either a positive or a negative edge. Finally, the register WKPND latches in the pending trigger conditions.
The GIE (Global Interrupt Enable) bit enables the interrupt function.
A control flag, LPEN, functions as a global interrupt enable for Port L interrupts. Setting the LPEN flag will enable inter­rupts and vice versa. A separate global pending flag is not needed since the register WKPND is adequate.
Since Port L is also used for waking the device out of the HALTor IDLE modes, the user can elect to exit the HALT or IDLE modes either with or without the interrupt enabled. If he elects to disable the interrupt, then the device will restart execution from the instruction immediately following the in­struction that placed the microcontroller in the HALT or IDLE modes. In the other case, the device will first execute the interrupt service routine and then revert to normal operation. (See HALT MODE for clock option wakeup information.)
9.6 INTERRUPT SUMMARY
The device uses the following types of interrupts, listed below in order of priority:
1. The Software Trap non-maskable interrupt, triggered by the INTR (00 opcode) instruction. The Software Trap is acknowledged immediately. This interrupt service rou­tine can be interrupted only by another Software Trap. The Software Trap should end with two RPND instruc­tions followed by a restart procedure.
2. Maskable interrupts, triggered by an on-chip peripheral block or an external device connected to the device. Under ordinary conditions, a maskable interrupt will not interrupt any other interrupt routine in progress. A maskable interrupt routine in progress can be inter­rupted by the non-maskable interrupt request. A maskable interrupt routine should end with an RETI instruction.
www.national.com33
Page 34
10.0 WATCHDOG/Clock Monitor
The devices contain a user selectable WATCHDOG and clock monitor. The following section is applicable only if WATCHDOG feature has been selected in the ECON regis­ter.The WATCHDOG is designed to detect the user program getting stuck in infinite loops resulting in loss of program
COP8SA Family
control or “runaway” programs. The WATCHDOG logic contains two separate service win-
dows. While the user programmable upper window selects the WATCHDOG service time, the lower window provides protection against an infinite program loop that contains the WATCHDOG service instruction.
The COP8SAx devices provide the added feature of a soft­ware trap that provides protection against stack overpops and addressing locations outside valid user program space.
The Clock Monitor is used to detect the absence of a clock or a very slow clock below a specified rate on the CKI pin.
The WATCHDOG consists of two independent logic blocks: WD UPPER and WD LOWER. WD UPPER establishes the upper limit on the service window and WD LOWER defines the lower limit of the service window.
Servicing the WATCHDOG consists of writing a specific value to a WATCHDOG Service Register named WDSVR which is memory mapped in the RAM. This value is com­posed of three fields, consisting of a 2-bit Window Select, a 5-bit Key Data field, and the 1-bit Clock Monitor Select field.
Table 6
The lower limit of the service window is fixed at 256 instruc­tion cycles. Bits 7 and 6 of the WDSVR register allow the user to pick an upper limit of the service window.
Table 7
upper limits for the WATCHDOG service window. This flex­ibility in choosing the WATCHDOG service window prevents any undue burden on the user software.
Bits 5, 4, 3, 2 and 1 of the WDSVR register represent the 5-bit Key Data field. The key data is fixed at 01100. Bit 0 of the WDSVR Register is the Clock Monitor Select bit.
10.1 CLOCK MONITOR
The Clock Monitor aboard the device can be selected or deselected under program control. The Clock Monitor is guaranteed not to reject the clock if the instruction cycle clock (1/t clock input rate on CKI of greater or equal to 100 kHz.
shows the WDSVR register.
TABLE 6. WATCHDOG Service Register (WDSVR)
Window Key Data Clock
Select Monitor
X X 01100 Y
shows the four possible combinations of lower and
TABLE 7. WATCHDOG Service Window Select
WDSVR WDSVR Clock Service Window
Bit 7 Bit 6 Monitor (Lower-Upper Limits)
0 0 x 2048–8k t 0 1 x 2048–16k t 1 0 x 2048–32k t 1 1 x 2048–64k t
Cycles
C
C C C
x x 0 Clock Monitor Disabled x x 1 Clock Monitor Enabled
) is greater or equal to 10 kHz. This equates to a
C
Cycles Cycles Cycles
10.2 WATCHDOG/CLOCK MONITOR OPERATION
The WATCHDOG is enabled by bit 2 of the ECON register. When this ECON bit is 0, the WATCHDOG is enabled and pin G1 becomes the WATCHDOGoutput with a weak pullup.
The WATCHDOG and Clock Monitor are disabled during reset. The device comes out of reset with the WATCHDOG armed, the WATCHDOG Window Select bits (bits 6, 7 of the WDSVR Register) set, and the Clock Monitor bit (bit 0 of the WDSVR Register) enabled. Thus, a Clock Monitor error will occur after coming out of reset, if the instruction cycle clock frequency has not reached a minimum specified value, in­cluding the case where the oscillator fails to start.
The WDSVR register can be written to only once after reset and the key data (bits 5 through 1 of the WDSVR Register) must match to be a valid write. This write to the WDSVR register involves two irrevocable choices: (i) the selection of the WATCHDOG service window (ii) enabling or disabling of the Clock Monitor. Hence, the first write to WDSVR Register involves selecting or deselecting the Clock Monitor, select the WATCHDOG service window and match the WATCH­DOG key data. Subsequent writes to the WDSVR register will compare the value being written by the user to the WATCHDOG service window value and the key data (bits 7 through 1) in the WDSVR Register.
Table 8
shows the se-
quence of events that can occur. The user must service the WATCHDOGat least once before
the upper limit of the service window expires. The WATCH­DOG may not be serviced more than once in every lower limit of the service window. The user may service the WATCHDOG as many times as wished in the time period between the lower and upper limits of the service window. The first write to the WDSVR Register is also counted as a WATCHDOG service.
The WATCHDOG has an output pin associated with it. This is the WDOUT pin, on pin 1 of the port G. WDOUT is active low and must be externally connected to the RESET pin or to some other external logic whichhandlesWATCHDOG event. The WDOUT pin has a weak pullup in the inactive state. This pull-up is sufficient to serve as the connection to V
for
CC
systems which use the internal Power On Reset. Upon triggering the WATCHDOG, the logic will pull the WDOUT (G1) pin low for an additional 16 t
–32tCcycles after the
C
signal level on WDOUT pin goes below the lower Schmitt trigger threshold. After this delay, the device will stop forcing the WDOUT output low. The WATCHDOG service window will restart when the WDOUT pin goes high.
The Clock Monitor forces the G1 pin low upon detecting a clock frequency error. The Clock Monitor error will continue until the clock frequency has reached the minimum specified value, after which the G1 output will go high following 16 t
–32 tCclock cycles. The Clock Monitor generates a con-
C
tinual Clock Monitor error if the oscillator fails to start, or fails to reach the minimum specified frequency. The specification for the Clock Monitor is as follows:
>
1/t
10 kHz—No clock rejection.
C
<
1/t
10 Hz—Guaranteed clock rejection.
C
www.national.com 34
Page 35
10.0 WATCHDOG/Clock Monitor (Continued)
TABLE 8. WATCHDOG Service Actions
Key Window Clock Action
Data Data Monitor
Match Match Match Valid Service: Restart Service Window
Don’t Care Mismatch Don’t Care Error: Generate WATCHDOG Output
Mismatch Don’t Care Don’t Care Error: Generate WATCHDOG Output
Don’t Care Don’t Care Mismatch Error: Generate WATCHDOG Output
COP8SA Family
10.3 WATCHDOG AND CLOCK MONITOR SUMMARY
The following salient points regarding the WATCHDOG and CLOCK MONITOR should be noted:
Both the WATCHDOG and CLOCK MONITOR detector
•
circuits are inhibited during RESET. Following RESET, the WATCHDOG and CLOCK MONI-
•
TOR are both enabled, with the WATCHDOG having the maximum service window selected.
The WATCHDOG service window and CLOCK MONI-
•
TOR enable/disable option can only be changed once, during the initial WATCHDOG service following RESET.
The initial WATCHDOG service must match the key data
•
value in the WATCHDOG Service register WDSVR in order to avoid a WATCHDOG error.
Subsequent WATCHDOG services must match all three
•
data fields in WDSVR in order to avoid WATCHDOG errors.
The correct key data value cannot be read from the
•
WATCHDOG Service register WDSVR. Any attempt to read this key data value of 01100 from WDSVR will read as key data value of all 0’s.
The WATCHDOG detector circuit is inhibited during both
•
the HALT and IDLE modes. The CLOCK MONITOR detector circuit is active during
•
both the HALT and IDLE modes. Consequently, the de­vice inadvertently entering the HALT mode will be de­tected as a CLOCK MONITOR error (provided that the CLOCK MONITOR enable option has been selected by the program).
With the single-pin R/C oscillator option selected and the
•
CLKDLY bit reset, the WATCHDOG service window will resume following HALT mode from where it left off before entering the HALT mode.
With the crystal oscillator option selected, or with the
•
single-pin R/C oscillator option selected and the CLKDLY bit set, the WATCHDOG service window will be set to its selected value from WDSVR following HALT. Conse­quently, the WATCHDOG should not be serviced for at least 256 instruction cycles following HALT, but must be serviced within the selected window to avoid a WATCH­DOG error.
The IDLE timer T0 is not initialized with external RESET.
•
The user can sync in to the IDLE counter cycle with an
•
IDLE counter (T0) interrupt or by monitoring the T0PND flag. The T0PND flag is set whenever the twelfth bit of the IDLE counter toggles (every 4096 instruction cycles). The user is responsible for resetting the T0PND flag.
A hardware WATCHDOG service occurs just as the de-
•
vice exits the IDLE mode. Consequently, the WATCH­DOG should not be serviced for at least 256 instruction cycles following IDLE, but must be serviced within the selected window to avoid a WATCHDOG error.
Following RESET,the initial WATCHDOG service (where
•
the service window and the CLOCK MONITOR enable/ disable must be selected) may be programmed any­where within the maximum service window (65,536 in­struction cycles) initialized by RESET. Note that this initial WATCHDOG service may be programmed within the ini­tial 256 instruction cycles without causing a WATCHDOG error.
In order to RESET the device on the occurrence of a
•
WATCH event, the user must connect the WDOUT pin (G1) pin to the RESET external to the device. The weak pull-up on the WDOUT pin is sufficient to provide the RESET connection to V Power On Reset and WATCHDOG.
10.4 DETECTION OF ILLEGAL CONDITIONS
The device can detect various illegal conditions resulting from coding errors, transient noise, power supply voltage drops, runaway programs, etc.
Reading of undefined ROM gets zeroes. The opcode for software interrupt is 00. If the program fetches instructions from undefined ROM, this will force a software interrupt, thus signaling that an illegal condition has occurred.
The subroutine stack grows down for each call (jump to subroutine), interrupt, or PUSH, and grows up for each return or POP. The stack pointer is initialized to RAM location 06F Hex during reset. Consequently, if there are more re­turns than calls, the stack pointer will point to addresses 070 and 071 Hex (which are undefined RAM). Undefined RAM from addresses 070 to 07F (Segment 0), and all other seg­ments (i.e., Segments 4 … etc.) is read as all 1’s, which in turn will cause the program to return to address 7FFF Hex. This is an undefined ROM location and the instruction fetched (all 0’s) from this location will generate a software interrupt signaling an illegal condition.
Thus, the chip can detect the following illegal conditions:
1. Executing from undefined ROM
2. Over “POP”ing the stack by having more returns than calls.
When the software interrupt occurs, the user can re-initialize the stack pointer and do a recovery procedure before restart­ing (this recovery program is probably similar to that follow­ing reset, but might not contain the same program initializa­tion procedures). The recovery program should reset the software interrupt pending bit using the RPND instruction.
for devices which use both
CC
www.national.com35
Page 36
11.0 MICROWIRE/PLUS
MICROWIRE/PLUS is a serial SPI compatible synchronous communications interface. The MICROWIRE/PLUS capabil­ity enables the device to interface with MICROWIRE/PLUS or SPI peripherals (i.e. A/D converters, display drivers, EE­PROMs etc.) and with other microcontrollers which support
COP8SA Family
the MICROWIRE/PLUS or SPI interface. It consists of an 8-bit serial shift register (SIO) with serial data input (SI), serial data output (SO) and serial shift clock (SK). shows a block diagram of the MICROWIRE/PLUS logic.
The shift clock can be selected from either an internal source or an external source. Operating the MICROWIRE/PLUS arrangement with the internal clock source is called the Master mode of operation. Similarly, operating the MICROWIRE/PLUS arrangement with an external shift clock is called the Slave mode of operation.
The CNTRL register is used to configure and control the MICROWIRE/PLUS mode. To use the MICROWIRE/PLUS, the MSEL bit in the CNTRL register is set to one. In the master mode, the SK clock rate is selected by the two bits, SL0 and SL1, in the CNTRL register. different clock rates that may be selected.
TABLE 9. MICROWIRE/PLUS
Master Mode Clock Select
SL1 SL0 SK Period
0 0 2xt 0 1 4xt 1 x 8xt
Table 9
C C C
Figure 24
details the
11.1 MICROWIRE/PLUS OPERATION
Setting the BUSY bit in the PSW register causes the MICROWIRE/PLUS to start shifting the data. It gets reset when eight data bits have been shifted. The user may reset the BUSY bit by software to allow less than 8 bits to shift. If enabled, an interrupt is generated when eight data bits have been shifted. The device may enter the MICROWIRE/PLUS mode either as a Master or as a Slave.
Figure 24
shows how two microcontroller devices and several peripherals may be interconnected using the MICROWIRE/PLUS arrangements.
WARNING
The SIO register should only be loaded when the SK clock is in the idle phase. Loading theSIOregisterwhiletheSKclock is in the active phase, will result in undefined data in the SIO register.
Setting the BUSY flag when the input SK clock is in the active phase while in the MICROWIRE/PLUS is in the slave mode may cause the current SK clock for the SIO shift register to be narrow. For safety, the BUSY flag should only be set when the input SK clock is in the idle phase.
11.1.1 MICROWIRE/PLUS Master Mode Operation
In the MICROWIRE/PLUS Master mode of operation the shift clock (SK) is generated internally. The MICROWIRE Master always initiates all data exchanges. The MSEL bit in the CNTRL register must be set to enable the SO and SK functions onto the G Port. The SO and SK pins must also be selected as outputs by setting appropriate bits in the Port G configuration register. In the slave mode, the shift clock stops after 8 clock pulses.
Table 10
summarizes the bit
settings required for Master mode of operation.
Where tCis the instruction cycle clock
DS012838-32
FIGURE 24. MICROWIRE/PLUS Application
www.national.com 36
Page 37
11.0 MICROWIRE/PLUS (Continued)
11.1.2 MICROWIRE/PLUS Slave Mode Operation
In the MICROWIRE/PLUS Slave mode of operation the SK clock is generated by an external source. Setting the MSEL bit in the CNTRL register enables the SO and SK functions onto the G Port. The SK pin must be selected as an input and the SO pin is selected as an output pin by setting and resetting the appropriate bits in the Port G configuration register. the Slave mode of operation.
This table assumes that the control flag MSEL is set.
Table 10
summarizes the settings required to enter
TABLE 10. MICROWIRE/PLUS Mode Settings
G4 (SO) G5 (SK) G4 G5
Config. Bit Config. Bit Fun. Fun.
1 1 SO Int. MICROWIRE/PLUS
SK Master
0 1 TRI- Int. MICROWIRE/PLUS
STATE SK Master
1 0 SO Ext. MICROWIRE/PLUS
SK Slave
0 0 TRI- Ext. MICROWIRE/PLUS
STATE SK Slave
Operation
COP8SA Family
The user must set the BUSY flag immediately upon entering the Slave mode. This ensures that all data bits sent by the Master is shifted properly.After eight clock pulses the BUSY flag is clear, the shift clock is stopped, and the sequence may be repeated.
10.1.3 Alternate SK Phase Operation and SK Idle Polarity
The device allows either the normal SK clock or an alternate phase SK clock to shift data in and out of the SIO register. In both the modes the SK idle polarity can be either high or low. The polarity is selected by bit 5 of Port G data register. In the normal mode data is shifted in on the rising edge of the SK clock and the data is shifted out on the falling edge of the SK clock. The SIO register is shifted on each falling edge of the SK clock. In the alternate SK phase operation, data is shifted in on the falling edge of the SK clock and shifted out on the rising edge of the SK clock. Bit 6 of Port G configuration register selects the SK edge.
TABLE 11. MICROWIRE/PLUS Shift Clock Polarity and Sample/Shift Phase
Port G
SK Phase G6 (SKSEL) G5
Config. Bit Data Bit
SO Clocked Out On: SI Sampled On:
SK Idle
Phase
Normal 0 0 SK Falling Edge SK Rising Edge Low Alternate 1 0 SK Rising Edge SK Falling Edge Low Alternate 0 1 SK Rising Edge SK Falling Edge High
Normal 1 1 SK Falling Edge SK Rising Edge High
DS012838-33
FIGURE 25. MICROWIRE/PLUS SPI Mode Interface Timing, Normal SK Mode, SK Idle Phase being Low
DS012838-34
FIGURE 26. MICROWIRE/PLUS SPI Mode Interface Timing, Alternate SK Mode, SK Idle Phase being Low
www.national.com37
Page 38
11.0 MICROWIRE/PLUS (Continued)
COP8SA Family
FIGURE 27. MICROWIRE/PLUS SPI Mode Interface Timing, Alternate SK Mode, SK Idle Phase being High
FIGURE 28. MICROWIRE/PLUS SPI Mode Interface Timing, Normal SK Mode, SK Idle Phase being High
DS012838-35
DS012838-31
www.national.com 38
Page 39
12.0 Memory Map
All RAM, ports and registers (except A and PC) are mapped into data memory address space.
COP8SA Family
RAM Address
Select ADD REG
64 On-Chip RAM Bytes. 02 to 2F On-Chip RAM (48 Bytes) (COP8SAAx) 30 to 7F Unused RAM (Reads as all ones) 128 On-Chip RAM Bytes 00 to 6F On-Chip RAM (112 Bytes) (COP8SABx/SACx) 70 to 7F Unused RAM (Reads as all ones)
80 to 93 Reserved
94 Port F Data Register 95 Port F Configuration Register 96 Port F Input Pins (Read Only) 97 Reserved
A0 to C6 Reserved
C7 WATCHDOG Service Register (Reg: WDSVR) C8 MIWU Edge Select Register (Reg: WKEDG) C9 MIWU Enable Register (Reg: WKEN)
CA MIWU Pending Register (Reg: WKPND)
CB to CF Reserved
D0 Port L Data Register D1 Port L Configuration Register D2 Port L Input Pins (Read Only) D3 Reserved D4 Port G Data Register D5 Port G Configuration Register D6 Port G Input Pins (Read Only) D7 Reserved D8 Port C Data Register D9 Port C Configuration Register DA Port C Input Pins (Read Only) DB Reserved DC Port D
DD to DF Reserved
E0 to E5 Reserved
E6 Timer T1 Autoload Register T1RB Lower Byte E7 Timer T1 Autoload Register T1RB Upper Byte E8 ICNTRL Register
E9 MICROWIRE/PLUS Shift Register EA Timer T1 Lower Byte EB Timer T1 Upper Byte EC Timer T1 Autoload Register T1RA Lower Byte ED Timer T1 Autoload Register T1RA Upper Byte EE CNTRL Control Register EF PSW Register
F0 to FB On-Chip RAM Mapped as Registers
FC X Register FD SP Register FE B Register
FF Reserved (Segment Register)
Reading any undefined memory location in the address range of 0080H–00FFH will return undefined data.
Contents
www.national.com39
Page 40
13.0 Instruction Set
13.1 INTRODUCTION
This section defines the instruction set of the COP8SAx Family members. It contains information about the instruc­tion set features, addressing modes and types.
COP8SA Family
13.2 INSTRUCTION FEATURES
The strength of the instruction set is based on the follow­ing features:
Mostly single-byte opcode instructions minimize pro-
•
gram size. One instruction cycle for the majority of single-byte
•
instructions to minimize program execution time. Many single-byte, multiple function instructions such
•
as DRSZ. Three memory mapped pointers: two for register indi-
•
rect addressing, and one for the software stack. Sixteen memory mapped registers that allow an opti-
•
mized implementation of certain instructions. Ability to set, reset, and test any individual bit in data
•
memory address space, including the memory-mapped I/O ports and registers.
Register-Indirect LOAD and EXCHANGE instructions
•
with optional automatic post-incrementing or decre­menting of the register pointer. This allows for greater efficiency (both in cycle time and program code) in loading, walking across and processing fields in data memory.
Unique instructions to optimize program size and
•
throughput efficiency. Some of these instructions are DRSZ, IFBNE, DCOR, RETSK, VIS and RRC.
12.3 ADDRESSING MODES
The instruction set offers a variety of methods for speci­fying memory addresses. Each method is called an ad­dressing mode. These modes are classified into two cat­egories: operand addressing modes and transfer-of-control addressing modes. Operand address­ing modes are the various methods of specifying an ad­dress for accessing (reading or writing) data. Transfer-of-control addressing modes are used in con­junction with jump instructions to control the execution sequence of the software program.
13.3.1 Operand Addressing Modes
The operand of an instruction specifies what memory location is to be affected by that instruction. Several dif­ferent operand addressing modes are available, allowing memory locations to be specified in a variety of ways. An instruction can specify an address directly by supplying the specific address, or indirectly by specifying a register pointer. The contents of the register (or in some cases, two registers) point to the desired memory location. In the immediate mode, the data byte to be used is contained in the instruction itself.
Each addressing mode has its own advantages and dis­advantages with respect to flexibility, execution speed, and program compactness. Not all modes are available with all instructions. The Load (LD) instruction offers the largest number of addressing modes.
The available addressing modes are:
Direct
•
Register B or X Indirect
•
Register B or X Indirect with Post-Incrementing/
•
Decrementing Immediate
•
Immediate Short
•
Indirect from Program Memory
•
The addressing modes are described below. Each de­scription includes an example of an assembly language instruction using the described addressing mode.
Direct. The memory address isspecifieddirectlyasabyte in the instruction. In assembly language, the direct ad­dress is written as a numerical value (or a label that has been defined elsewhere in the program as a numerical value).
Example: Load Accumulator Memory Direct
LD A,05
Reg/Data Contents Contents
Memory Before After
Accumulator XX Hex A6 Hex
Memory Location A6 Hex A6 Hex
0005 Hex
Register B or X Indirect. The memory address is specified by the contents of the B Register or X register (pointer register). In assembly language, the notation [B] or [X] speci­fies which register serves as the pointer.
Example: Exchange Memory with Accumulator, B Indirect
X A,[B]
Reg/Data Contents Contents
Memory Before After
Accumulator 01 Hex 87 Hex
Memory Location 87 Hex 01 Hex
0005 Hex
B Pointer 05 Hex 05 Hex
Register B or X Indirect with Post-Incrementing/ Decrementing. The relevant memory address is specified
by the contents of the B Register or X register (pointer register). The pointer register is automatically incremented or decremented after execution, allowing easy manipulation of memory blocks with software loops. In assembly lan­guage, the notation [B+], [B−], [X+], or [X−] specifies which register serves as the pointer, and whether the pointer is to be incremented or decremented.
Example: Exchange Memory with Accumulator, B Indirect
with Post-Increment X A,[B+]
Reg/Data Contents Contents
Memory Before After
Accumulator 03 Hex 62 Hex
Memory Location 62 Hex 03 Hex
0005 Hex
B Pointer 05 Hex 06 Hex
Intermediate. The data for the operation follows the instruc­tion opcode in program memory. In assembly language, the number sign character (
#
) indicates an immediate operand.
www.national.com 40
Page 41
13.0 Instruction Set (Continued)
Example: Load Accumulator Immediate
#
LD A,
05
Reg/Data Contents Contents
Memory Before After
Accumulator XX Hex 05 Hex
Example: Load B Register Immediate Short
#
LD B,
7
Reg/Data Contents Contents
Memory Before After
B Pointer 12 Hex 07 Hex
Example: Load Accumulator Indirect
LAID
Reg/Data Contents Contents
Memory Before After
PCU 04 Hex 04 Hex
PCL 35 Hex 36 Hex
Accumulator 1F Hex 25 Hex
Memory Location 25 Hex 25 Hex
041F Hex
13.3.2 Tranfer-of-Control Addressing Modes
Program instructions are usually executed in sequential or­der. However, Jump instructions can be used to change the normal execution sequence. Several transfer-of-control ad­dressing modes are available to specify jump addresses.
A change in program flow requires a non-incremental change in the Program Counter contents. The Program Counter consists of two bytes, designated the upper byte (PCU) and lower byte (PCL). The most significant bit of PCU is not used, leaving 15 bits to address the program memory.
Different addressing modes are used to specify the new address for the Program Counter. The choice of addressing mode depends primarily on the distance of the jump. Farther jumps sometimes require more instruction bytes in order to completely specify the new Program Counter contents.
The available transfer-of-control addressing modes are:
Jump Relative
•
Jump Absolute
•
Jump Absolute Long
•
Jump Indirect
•
The transfer-of-control addressing modes are described be­low. Each description includes an example of a Jump in­struction using a particular addressing mode, and the effect on the Program Counter bytes of executing that instruction.
Jump Relative. In this 1-byte instruction, six bits of the instruction opcode specify the distance of the jump from the current program memory location. The distance of the jump can range from −31 to +32. AJP+1 instruction is not allowed. The programmer should use a NOP instead.
Example: Jump Relative
JP 0A
Reg Contents Contents
Before After
PCU 02 Hex 02 Hex
PCL 05 Hex 0F Hex
(This restriction is relevant only in devices using more than one 4 kbyte program memory space.)
Example: Jump Absolute
JMP 0125
Reg Contents Contents
Before After
PCU 0C Hex 01 Hex
PCL 77 Hex 25 Hex
Example: Jump Absolute Long
JMP 03625
Reg/ Contents Contents
Memory Before After
PCU 42 Hex 36 Hex
PCL 36 Hex 25 Hex
COP8SA Family
www.national.com41
Page 42
13.0 Instruction Set (Continued)
Jump Indirect. In this 1-byte instruction, the lower byte of
the jump address is obtained from a table stored in program memory, with the Accumulator serving as the low order byte of a pointer into program memory. For purposes of access-
COP8SA Family
Example: Jump Indirect
JID
Reg/ Contents Contents
Memory Before After
PCU 01 Hex 01 Hex
PCL C4 Hex 32 Hex
Accumulator 26 Hex 26 Hex
Memory
Location 32 Hex 32 Hex
0126 Hex
The VIS instruction is a special case of the Indirect Transfer of Control addressing mode, where the double-byte vector associated with the interrupt is transferred from adjacent addresses in program memory into the Program Counter in order to jump to the associated interrupt service routine.
13.4 INSTRUCTION TYPES
The instruction set contains a wide variety of instructions. The available instructions are listed below, organized into related groups.
Some instructions test a condition and skip the next instruc­tion if the condition is not true. Skipped instructions are executed as no-operation (NOP) instructions.
13.4.1 Arithmetic Instructions
The arithmetic instructions perform binary arithmetic such as addition and subtraction, with or without the Carry bit.
Add (ADD) Add with Carry (ADC) Subtract (SUB) Subtract with Carry (SUBC) Increment (INC) Decrement (DEC) Decimal Correct (DCOR) Clear Accumulator (CLR) Set Carry (SC) Reset Carry (RC)
13.4.2 Transfer-of-Control Instructions
The transfer-of-control instructions change the usual se­quential program flow by altering the contents of the Pro­gram Counter. The Jump to Subroutine instructions save the Program Counter contents on the stack before jumping; the Return instructions pop the top of the stack back into the Program Counter.
Jump Relative (JP) Jump Absolute (JMP) Jump Absolute Long (JMPL) Jump Indirect (JID) Jump to Subroutine (JSR)
Jump to Subroutine Long (JSRL) Return from Subroutine (RET) Return from Subroutine and Skip (RETSK) Return from Interrupt (RETI) Software Trap Interrupt (INTR) Vector Interrupt Select (VIS)
13.4.3 Load and Exchange Instructions
The load and exchange instructions write byte values in registers or memory. The addressing mode determines the source of the data.
Load (LD) Load Accumulator Indirect (LAID) Exchange (X)
13.4.4 Logical Instructions
The logical instructions perform the operations AND, OR, and XOR (Exclusive OR). Other logical operations can be performed by combining these basic operations. For ex­ample, complementing is accomplished by exclusiveORing the Accumulator with FF Hex.
Logical AND (AND) Logical OR (OR) Exclusive OR (XOR)
13.4.5 Accumulator Bit Manipulation Instructions
The Accumulator bit manipulation instructions allow the user to shift the Accumulator bits and to swap its two nibbles.
Rotate Right Through Carry (RRC) Rotate Left Through Carry (RLC) Swap Nibbles of Accumulator (SWAP)
13.4.6 Stack Control Instructions
Push Data onto Stack (PUSH) Pop Data off of Stack (POP)
13.4.7 Memory Bit Manipulation Instructions
The memory bit manipulation instructions allow the user to
set and reset individual bits in memory.
Set Bit (SBIT) Reset Bit (RBIT) Reset Pending Bit (RPND)
13.4.8 Conditional Instructions
If Equal (IFEQ) If Not Equal (IFNE) If Greater Than (IFGT) If Carry (IFC) If Not Carry (IFNC) If Bit (IFBIT) If B Pointer Not Equal (IFBNE) And Skip if Zero (ANDSZ) Decrement Register and Skip if Zero (DRSZ)
www.national.com 42
Page 43
13.0 Instruction Set (Continued)
13.4.9 No-Operation Instruction
The no-operation instruction does nothing, except to occupy space in the program memory and time in execution.
No-Operation (NOP)
Note: TheVIS is a special case of theIndirect Transfer of Control addressing
mode, where the double byte vector associated with the interrupt is transferred from adjacent addresses in the program memory into the program counter (PC) in order to jump to the associated interrupt service routine.
13.5 REGISTER AND SYMBOL DEFINITION
The following abbreviations represent the nomenclature used in the instruction description and the COP8 cross-assembler.
Registers
A 8-Bit Accumulator Register B 8-Bit Address Register X 8-Bit Address Register SP 8-Bit Stack Pointer Register PC 15-Bit Program Counter Register PU Upper 7 Bits of PC PL Lower 8 Bits of PC C 1 Bit of PSW Register for Carry HC 1 Bit of PSW Register for Half Carry GIE 1 Bit of PSW Register for Global Interrupt
Enable VU Interrupt Vector Upper Byte VL Interrupt Vector Lower Byte
COP8SA Family
Symbols
[B] Memory Indirectly Addressed by B Register [X] Memory Indirectly Addressed by X Register MD Direct Addressed Memory Mem Direct Addressed Memory or [B] Meml Direct Addressed Memory or [B] or
Immediate Data Imm 8-Bit Immediate Data Reg Register Memory: Addresses F0 to FF
(Includes B, X and SP) Bit Bit Number (0 to 7)
←
↔
Loaded with
Exchanged with
www.national.com43
Page 44
13.0 Instruction Set (Continued)
13.6 INSTRUCTION SET SUMMARY
ADD A,Meml ADD A←A + Meml ADC A,Meml ADD with Carry A←A+Meml+C,C←Carry,
COP8SA Family
SUBC A,Meml Subtract with Carry A←A−MemI+C,C←Carry,
AND A,Meml Logical AND A←A and Meml ANDSZ A,Imm Logical AND Immed., Skip if Zero Skip next if (A and Imm) = 0 OR A,Meml Logical OR A←A or Meml XOR A,Meml Logical EXclusive OR A←A xor Meml IFEQ MD,Imm IF EQual Compare MD and Imm, Do next if MD = Imm IFEQ A,Meml IF EQual Compare A and Meml, Do next if A = Meml IFNE A,Meml IF Not Equal Compare A and Meml, Do next if A IFGT A,Meml IF Greater Than Compare A and Meml, Do next if A IFBNE DRSZ Reg Decrement Reg., Skip if Zero Reg←Reg − 1, Skip if Reg = 0 SBIT RBIT IFBIT RPND Reset PeNDing Flag Reset Software Interrupt Pending Flag X A,Mem EXchange A with Memory A X A,[X] EXchange A with Memory [X] A LD A,Meml LoaD A with Memory A←Meml LD A,[X] LoaD A with Memory [X] A←[X] LD B,Imm LoaD B with Immed. B←Imm LD Mem,Imm LoaD Memory Immed. Mem←Imm LD Reg,Imm LoaD Register Memory Immed. Reg←Imm XA,[B XA,[X LD A, [B LD A, [X LD [B CLR A CLeaR A A←0 INC A INCrement A A←A+1 DEC A DECrement A A←A−1 LAID Load A InDirect from ROM A←ROM (PU,A) DCOR A Decimal CORrect A A←BCD correction of A (follows ADC, SUBC) RRC A Rotate A Right thru C C→A7→…→A0→C RLC A Rotate A Left thru C C←A7←…←A0←C, HC←A0 SWAP A SWAP nibbles of A A7…A4 SC Set C C←1, HC←1 RC Reset C C←0, HC←0 IFC IF C IF C is true, do next instruction IFNC IF Not C If C is not true, do next instruction POP A POP the stack into A SP←SP+1,A←[SP] PUSH A PUSH A onto the stack [SP]←A, SP←SP−1 VIS Vector to Interrupt Service Routine PU←[VU], PL←[VL] JMPL Addr. Jump absolute Long PC←ii (ii = 15 bits, 0 to 32k) JMP Addr. Jump absolute PC9…0←i (i = 12 bits) JP Disp. Jump relative short PC←PC+r(ris−31to+32, except 1)
#
#
,Mem Set BIT 1 to bit, Mem (bit = 0 to 7 immediate)
#
,Mem Reset BIT 0 to bit, Mem
#
,Mem IF BIT If bit#, A or Mem is true do next instruction
± ±
±
] LoaD A with Memory [B] A←[B], (B←B±1)
±
] LoaD A with Memory [X] A←[X], (X←X±1)
±
],Imm LoaD Memory [B] Immed. [B]←Imm, (B←B±1)
If B Not Equal Do next if lower 4 bits of B≠Imm
] EXchange A with Memory [B] A↔[B], (B←B±1) ] EXchange A with Memory [X] A↔[X], (X←X±1)
HC←Half Carry
HC←Half Carry
↔
Mem
↔
[X]
↔
A3…A0
≠
>
Meml
Meml
www.national.com 44
Page 45
13.0 Instruction Set (Continued)
JSRL Addr. Jump SubRoutine Long [SP]←PL, [SP−1]←PU,SP−2, PC←ii JSR Addr. Jump SubRoutine [SP]←PL, [SP−1]←PU,SP−2, PC9…0←i JID Jump InDirect PL←ROM (PU,A) RET RETurn from subroutine SP + 2, PL←[SP], PU←[SP−1] RETSK RETurn and SKip SP + 2, PL←[SP],PU←[SP−1],
skip next instruction RETI RETurn from Interrupt SP + 2, PL←[SP],PU←[SP−1],GIE←1 INTR Generate an Interrupt [SP]←PL, [SP−1]←PU, SP−2, PC←0FF NOP No OPeration PC←PC+1
COP8SA Family
13.7 INSTRUCTION EXECUTION TIME
Most instructions are single byte (with immediate addressing mode instructions taking two bytes).
Most single byte instructions take one cycle time to execute. Skipped instructions require x number of cycles to be
See the BYTES and CYCLES per INSTRUCTION table for details.
Bytes and Cycles per Instruction
The following table shows the number ofbytesandcyclesfor each instruction in the format of byte/cycle.
Arithmetic and Logic Instructions
[B] Direct Immed.
ADD 1/1 3/4 2/2 ADC 1/1 3/4 2/2 SUBC 1/1 3/4 2/2 AND 1/1 3/4 2/2 OR 1/1 3/4 2/2 XOR 1/1 3/4 2/2 IFEQ 1/1 3/4 2/2 IFGT 1/1 3/4 2/2 IFBNE 1/1 DRSZ 1/3 SBIT 1/1 3/4 RBIT 1/1 3/4 IFBIT 1/1 3/4
RPND 1/1
Instructions Using A & C
CLRA 1/1 INCA 1/1 DECA 1/1 LAID 1/3 DCORA 1/1 RRCA 1/1 RLCA 1/1 SWAPA 1/1 SC 1/1 RC 1/1 IFC 1/1 IFNC 1/1 PUSHA 1/3 POPA 1/3 ANDSZ 2/2
Transfer of Control Instructions
JMPL 3/4 JMP 2/3 JP 1/3 JSRL 3/5 JSR 2/5 JID 1/3 VIS 1/5 RET 1/5 RETSK 1/5 RETI 1/5 INTR 1/7 NOP 1/1
www.national.com45
Page 46
13.0 Instruction Set (Continued)
Memory Transfer Instructions
Register Direct Immed. Register Indirect
COP8SA Family
X A, (Note 21) 1/1 1/3 2/3 1/2 1/3 LD A, (Note 21) 1/1 1/3 2/3 2/2 1/2 1/3 LD B, Imm 1/1 (If B LD B, Imm 2/2 (If B LD Mem, Imm 2/2 3/3 2/2 LD Reg, Imm 2/3 IFEQ MD, Imm 3/3
Note 21: =>Memory location addressed by B or X or directly.
Indirect Auto Incr. & Decr.
[B] [X] [B+, B−] [X+, X−]
<
16)
>
15)
www.national.com 46
Page 47
JP+17 INTR 0
JMP
IFBNE 0 JSR
LD
JP+18 JP+2 1
JMP
x000–x0FF
x000–x0FF
IFBNE 1 JSR
B,#0F
JP+19 JP+3 2
JMP
x100–x1FF
x100–x1FF
IFBNE 2 JSR
B,#0E
JP+20 JP+4 3
JMP
x200–x2FF
x200–x2FF
IFBNE 3 JSR
B,#0D
JP+21 JP+5 4
JMP
x300–x3FF
x300–x3FF
IFBNE 4 JSR
B,#0C
JP+22 JP+6 5
JMP
x400–x4FF
x400–x4FF
IFBNE 5 JSR
B,#0B
JP+23 JP+7 6
JMP
x500–x5FF
x500–x5FF
IFBNE 6 JSR
B,#0A
JP+24 JP+8 7
JMP
x600–x6FF
x600–x6FF
IFBNE 7 JSR
B,#09
JP+25 JP+9 8
JMP
x700–x7FF
x700–x7FF
IFBNE 8 JSR
LD
B,#08
JP+26 JP+10 9
JMP
x800–x8FF
x800–x8FF
IFBNE 9 JSR
LD
B,#07
Lower Nibble
x900–x9FF
x900–x9FF
B,#06
JP+27 JP+11 A
JMP
IFBNE 0A JSR
LD
JP+28 JP+12 B
JMP
xA00–xAFF
xA00–xAFF
IFBNE 0B JSR
LD
B,#05
JP+29 JP+13 C
JMP
xB00–xBFF
xB00–xBFF
IFBNE 0C JSR
LD
B,#04
JP+30 JP+14 D
JMP
xC00–xCFF
xC00–xCFF
IFBNE 0D JSR
LD
B,#03
JP+31 JP+15 E
JMP
xD00–xDFF
xD00–xDFF
IFBNE 0E JSR
LD
B,#02
JP+32 JP+16 F
JMP
xE00–xEFF
xE00–xEFF
IFBNE 0F JSR
LD
B,#01
COP8SA Family
xF00–xFFF
xF00–xFFF
B,#00
Upper Nibble
A, #i
ANDSZ
0,[B]
IFBIT
ADC
A,[B]
A,#i
RRCA RC ADC
0F0
*LD
*LD
1,[B]
IFBIT
IFBIT
A,[B]
IFEQ
SUBC
A, #i
IFEQ
X
* SC SUBC
X
0F1
*LD
2,[B]
IFBIT
A,[B]
IFGT
A,#i
IFGT
X
A,[B+]
X
A,[X+]
0F2
CLRA LD
3,[B]
IFBIT
ADD
A,[B]
A,#i
A,[B−]
VIS LAID ADD
A,[X−]
0F3
4,[B]
A,[B]
A,#i
0F4
SWAPA LD
5,[B]
IFBIT
AND
A,[B]
A,#i
RPND JID AND
0F5
DCORA LD
6,[B]
IFBIT
XOR
A,[B]
A,#i
XOR
A,[B]
X A,[X] X
0F6
PUSHA LD
7,[B]
IFBIT
A,[B]
* * OR A,#i OR
0F7
RBIT
NOP RLCA LD A,#i IFC SBIT
0,[B]
0,[B]
0F8
RBIT
IFNC SBIT
IFNE
IFEQ
IFNE
1,[B]
1,[B]
A,#i
Md,#i
A,[B]
0F9
2,[B]
RBIT
2,[B]
INCA SBIT
LD
[B+],#i
LD
A,[B+]
LD
A,[X+]
0FA
RBIT
DECA SBIT
LD
LD
LD
3,[B]
RBIT
3,[B]
[B−],#i
JMPL X A,Md POPA SBIT
A,[B−]
LD
A,[X−]
0FB
4,[B]
4,[B]
Md,#i
0FC
RBIT
RETSK SBIT
DIR JSRL LD
5,[B]
5,[B]
A,Md
0FD
6,[B]
RBIT
6,[B]
RET SBIT
LD
[B],#i
LD
A,[B]
LD
A,[X]
0FE
7,[B]
RBIT
7,[B]
* * LD B,#i RETI SBIT
0FF
13.8 Opcode Table
F E D C BA9 876 5 4 3 2 10
JP−15 JP−31 LD 0F0, #i DRSZ
JP−14 JP−30 LD 0F1, #i DRSZ
JP−13 JP−29 LD 0F2, #i DRSZ
JP−12 JP−28 LD 0F3, #i DRSZ
JP−11 JP−27 LD 0F4, #i DRSZ
JP−10 JP−26 LD 0F5, #i DRSZ
JP−9 JP−25 LD 0F6, #i DRSZ
JP−8 JP−24 LD 0F7, #i DRSZ
JP−7 JP−23 LD 0F8, #i DRSZ
JP−6 JP−22 LD 0F9, #i DRSZ
JP−5 JP−21 LD 0FA, #i DRSZ
JP−4 JP−20 LD 0FB, #i DRSZ
JP−3 JP−19 LD 0FC, #i DRSZ
JP−2 JP−18 LD 0FD, #i DRSZ
JP−1 JP−17 LD 0FE, #i DRSZ
JP−0 JP−16 LD 0FF, #i DRSZ
www.national.com47
i is the immediate data
Where,
Md is a directly addressed memory location
* is an unused opcode
The opcode 60 Hex is also the opcode for IFBIT #i,A
Page 48
14.0 Mask Options
For mask options information on COP8SAx5 devices, please refer to Section 6.4 ECON (CONFIGURATION) REGISTER.
15.0 Development Tools Support
COP8SA Family
15.1 OVERVIEW
National is engaged with an international community of in­dependent 3rd party vendors who provide hardware and software development tool support. Through National’s inter­action and guidance, these tools cooperate to form a choice of solutions that fits each developer’s needs.
This section provides a summary of the tool and develop­ment kits currently available. Up-to-date information, selec­tion guides, free tools, demos, updates, and purchase infor­mation can be obtained at our web site at: www.national.com/cop8.
15.2 SUMMARY OF TOOLS COP8 Evaluation Tools
COP8–NSEVAL: Free Software Evaluation package for
•
Windows. A fully integrated evaluation environment for COP8, including versions of WCOP8 IDE (Integrated Development Environment), COP8-NSASM, COP8­MLSIM, COP8C, DriveWay COP8 information.
COP8–MLSIM: Free Instruction Level Simulator tool for
•
Windows. For testing and debugging software instruc­tions only (No I/O or interrupt support).
COP8–EPU: Very Low cost COP8 Evaluation & Pro-
•
gramming Unit. Windows based evaluation and hardware-simulation tool, with COP8 device programmer and erasable samples. Includes COP8-NSDEV, Drive­way COP8 Demo, MetaLink Debugger, I/O cables and power supply.
COP8–EVAL-HIxx: Low cost target application evalua-
•
tion and development board for COP8Sx Families, from Hilton Inc. Real-time environment with integrated A/D, Temp Sensor, and Peripheral I/O.
COP8–EVAL-ICUxx: Very Low cost evaluation and de-
•
sign test board for COP8ACC and COP8SGx Families, from ICU. Real-time environment with add-on A/D, D/A, and EEPROM. Includes software routines and reference designs.
Manuals,ApplicationsNotes,Literature: Available free
•
from our web site at: www.national.com/cop8.
COP8 Integrated Software/Hardware Design Develop­ment Kits
COP8-EPU: Very Low cost Evaluation & Programming
•
Unit. Windows based development and hardware­simulation tool for COPSx/xG families, with COP8 device programmer and samples. Includes COP8-NSDEV, Driveway COP8 Demo, MetaLink Debugger, cables and power supply.
COP8-DM: Moderate cost Debug Module from MetaLink.
•
A Windows based, real-time in-circuit emulation tool with COP8 device programmer. Includes COP8-NSDEV, DriveWay COP8 Demo, MetaLink Debugger, power sup­ply, emulation cables and adapters.
COP8 Development Languages and Environments
COP8-NSASM: Free COP8 Assembler v5 for Win32.
•
Macro assembler, linker, and librarian for COP8 software
™
COP8, Manuals, and other
development. Supports all COP8 devices. (DOS/Win16 v4.10.2 available with limited support). (Compatible with WCOP8 IDE, COP8C, and DriveWay COP8).
COP8-NSDEV: Very low cost Software Development
•
Package for Windows. An integrated development envi­ronment for COP8, including WCOP8 IDE, COP8C (lim­ited version), COP8-NSASM, COP8-MLSIM.
COP8C: Moderately priced C Cross-Compiler and Code
•
Development System from Byte Craft (no code limit). Includes BCLIDE (Byte Craft Limited Integrated Develop­ment Environment) for Win32, editor, optimizing C Cross­Compiler, macro cross assembler, BC-Linker, and Met­aLink tools support. (DOS/SUN versions available; Compiler is installable under WCOP8 IDE; Compatible with DriveWay COP8).
EWCOP8-KS: Very Low cost ANSI C-Compiler and Em-
•
bedded Workbench from IAR (Kickstart version: COP8Sx/Fx only with 2k code limit; No FP). A fully inte­grated Win32 IDE, ANSI C-Compiler, macro assembler, editor, linker, Liberian, C-Spy simulator/debugger, PLUS MetaLink EPU/DM emulator support.
EWCOP8-AS: Moderately priced COP8 Assembler and
•
Embedded Workbench from IAR (no code limit). A fully integrated Win32 IDE, macro assembler, editor, linker, librarian, and C-Spy high-level simulator/debugger with I/O and interrupts support. (Upgradeable with optional C-Compiler and/or MetaLink Debugger/Emulator sup­port).
EWCOP8-BL: Moderately priced ANSI C-Compiler and
•
Embedded Workbench from IAR (Baseline version: All COP8 devices; 4k code limit; no FP). A fully integrated Win32 IDE, ANSI C-Compiler, macro assembler, editor, linker,librarian, and C-Spy high-level simulator/debugger. (Upgradeable; CWCOP8-M MetaLink tools interface sup­port optional).
EWCOP8: Full featured ANSI C-Compiler and Embed-
•
ded Workbench for Windows from IAR (no code limit). A fully integrated Win32 IDE, ANSI C-Compiler, macro as­sembler, editor, linker, librarian, and C-Spy high-level simulator/debugger. (CWCOP8-M MetaLink tools inter­face support optional).
EWCOP8-M: Full featured ANSI C-Compiler and Embed-
•
ded Workbench for Windows from IAR (no code limit). A fully integrated Win32 IDE, ANSI C-Compiler, macro as­sembler, editor, linker, librarian, C-Spy high-level simulator/debugger, PLUS MetaLink debugger/hardware interface (CWCOP8-M).
COP8 Productivity Enhancement Tools
WCOP8 IDE: Very Low cost IDE (Integrated Develop-
•
ment Environment) from KKD. Supports COP8C, COP8­NSASM, COP8-MLSIM, DriveWay COP8, and MetaLink debugger under a common Windows Project Manage­ment environment. Code development, debug, and emu­lation tools can be launched from the project window framework.
DriveWay-COP8: Low cost COP8 Peripherals Code
•
Generation tool from Aisys Corporation. Automatically generates tested and documented C or Assembly source code modules containing I/O drivers and interrupt han­dlers for each on-chip peripheral. Application specific code can be inserted for customization using the inte­grated editor. (Compatible with COP8-NSASM, COP8C, and WCOP8 IDE.)
www.national.com 48
Page 49
IM-COP8: MetaLink iceMASTER®. A full featured, real-
15.0 Development Tools Support
(Continued)
COP8-UTILS: Free set of COP8 assembly code ex-
•
amples, device drivers, and utilities to speed up code development.
COP8-MLSIM: Free Instruction Level Simulator tool for
•
Windows. For testing and debugging software instruc­tions only (No I/O or interrupt support).
COP8 Real-Time Emulation Tools
COP8-DM: MetaLink Debug Module. A moderately
•
priced real-time in-circuit emulation tool, with COP8 de­vice programmer. Includes MetaLink Debugger, power supply, emulation cables and adapters.
15.3 TOOLS ORDERING NUMBERS FOR THE COP8SAx FAMILY DEVICES
Note: The following order numbers apply to the COP8 devices in this datasheet only.
Vendor Tools Order Number Cost Notes
COP8-NSEVAL COP8-NSEVAL VL Order from web site. COP8-NSDEV COP8-NSDEV L Included in EM. Order CD from web site COP8-REF None COP8-EVAL COP8-EVAL-COB1 VL Order from web site COP8-EM COP8-EM-SA M Included p/s, 20/28/40 pin DIP target cable, manuals,
EM Target Cables and Adapters
Development Devices
COP8-PM COP8-PM-00 L Included p/s, manuals, software, 16/20/28/40 DIP/SO
OTP Programming Adapters
COP8-EMC-44P VL 44 PLCC Target Cable COP8-EMC-28CSP L 28 CSP Target Cable COP8-EMA-16D L 20 DIP to 16 DIP Adapter COP8-EMA-xxSO L DIP to SOIC Cable Converter COP8-EMA-44QFP L 44 pin PLCC to 44 QFP Cable Converter COP8SAC7Q VL 4k Eraseable/OTP devices
COP8-PGMA-44QFP L For programming 44 QFP on any programmer COP8-PGMA-28CSP L For programming 28 CSP on any programmer COP8-PGMA-44CSP L For programming 44 CSP on any programmer COP8-PGMA-28SO VL For programming 16/20/28 SOIC on any programmer
•
time in-circuit emulator for COP8 devices. Includes COP8-NSDEV, Driveway COP8 Demo, MetaLink Win­dows Debugger, and power supply. Package-specific probes and surface mount adaptors are ordered sepa­rately.
COP8 Device Programmer Support
MetaLink’s EPU and Debug Module include development
•
device programming capability for COP8 devices. Third-party programmers and automatic handling equip-
•
ment cover needs from engineering prototype and pilot production, to full production environments.
Factory programming available for high-volume require-
•
ments.
software
and 44 PLCC programming socket; add OTP adapter (if needed)
COP8SA Family
www.national.com49
Page 50
15.0 Development Tools Support (Continued)
MetaLink COP8-DM DM5-KCOP8-SA M Included p/s (PS-10), target cables (DIP and PLCC),
16/20/28/40 DIP/SO and 44 PLCC programming sockets. Add OTP adapter (if needed) and target
COP8SA Family
Cost: Free; VL =
DM Target Adapters
OTP Programming Adapters
COP8-IM IM-COP8-AD-464 (-220)
IM Probe Card PC-COP8SA44PW-AD-10 M 10 MHz 44 PLCC probe card; 2.5V to 6.0V
IM Probe Target Adapters
KKD WCOP8-IDE WCOP8-IDE VL Included in DM and EM
IAR EWCOP8-xx See summary above L - H Included all software and manuals
Byte
Craft
Aisys DriveWay COP8 DriveWay COP8 L Included all software and manuals
COP8C COP8C COP8CWIN M Included all software and manuals
OTP Programmers
<
$100; L = $100 - $300; M = $300 - $1k; H = $1k - $3k; VH = $3k - $5k
MHW-CNVxx (xx = 33, 34 etc.)
MHW-COP8-PGMA-DS L For programming 16/20/28 SOIC and 44 PLCC on the
MHW-COP8-PGMA-44QFP L For programming 44 QFP on any programmer MHW-COP8-PGMA-28CSP L For programming 28 CSP on any programmer
(10 MHz maximum)
PC-COP8SA40DW-AD-10 M 10 MHz 40 DIP probe card; 2.5V to 6.0V MHW-SOICxx (xx = 16,
20, 28) MHW-CONV33 L 44 pin QFP adapter for 44 PLCC probe card
Go to: www.national.com/cop8
adapter (if needed)
L DM target converters for
16DIP/20SO/28SO/44QFP/28CSP; (i.e. MHW-CNV38 for 20 pin DIP to SO package converter)
EPU
H Base unit 10 MHz; -220 = 220V; add probe card
(required) and target adapter (if needed); included software and manuals
L 16 or 20 or 28 pin SOIC adapter for probe card
L - H A wide variety world-wide
www.national.com 50
Page 51
15.0 Development Tools Support (Continued)
15.4 WHERE TO GET TOOLS
Tools are ordered directly from the following vendors. Please go to the vendor’s web site for current listings of distributors.
Vendor Home Office Electronic Sites Other Main Offices
Aisys U.S.A.: Santa Clara, CA www.aisysinc.com Distributors
1-408-327-8820 info fax: 1-408-327-8830
Byte Craft U.S.A. www.bytecraft.com Distributors
1-519-888-6911 info fax: 1-519-746-6751
IAR Sweden: Uppsala www.iar.se U.S.A.: San Francisco
+46 18 16 78 00 info fax: +46 18 16 78 38 info
ICU Sweden: Polygonvaegen www.icu.se Switzeland: Hoehe
+46 8 630 11 20 support
fax: +46 8 630 11 70 support KKD Denmark: www.kkd.dk MetaLink U.S.A.: Chandler, AZ www.metaice.com Germany: Kirchseeon
1-800-638-2423 sales
fax: 1-602-926-1198 support
National U.S.A.: Santa Clara, CA www.national.com/cop8 Europe: +49 (0) 180 530 8585
1-800-272-9959 support
fax: 1-800-737-7018 europe.support
@
aisysinc.com
@
bytecraft.com
@
iar.se 1-415-765-5500
@
iar.com fax: 1-415-765-5503
@
info
iarsys.co.uk U.K.: London
@
info
iar.de +44 171 924 33 34
fax: +44 171 924 53 41 Germany: Munich +49 89 470 6022 fax: +49 89 470 956
@
icu.se +41 34 497 28 20
@
icu.ch fax: +41 34 497 28 21
@
metaice.com 80-91-5696-0
@
metaice.com fax: 80-91-2386 bbs: 1-602-962-0013 islanger www.metalink.de Distributors Worldwide
@
nsc.com fax: +49 (0) 180 530 8586
@
nsc.com Distributors Worldwide
@
metalink.de
COP8SA Family
The following companies have approved COP8 program­mers in a variety of configurations. Contact your local office or distributor. You can link to their web sites and get the latest listing of approved programmers from National’s COP8 OTP Support page at: www.national.com/cop8.
Advantech; Dataman; EE Tools; Minato; BP Microsystems; Data I/O; Hi-Lo Systems; ICE Technology; Lloyd Research; Logical Devices; MQP; Needhams; Phyton; SMS; Stag Pro­grammers; System General; Tribal Microsystems; Xeltek.
15.5 CUSTOMER SUPPORT
Complete product information and technical support is avail­able from National’s customer response centers, and from our on-line COP8 customer support sites.
www.national.com51
Page 52
Physical Dimensions inches (millimeters) unless otherwise noted
COP8SA Family
20-Lead Hermetic Dual-In-Line Package, EPROM (D)
Order Number COP8SAC720Q3
NS Package Number D20CQ
www.national.com 52
Page 53
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
COP8SA Family
Molded Small Outline Package (WM)
Order Number COP8SAA716M8 or COP8SAA716M9
NS Package Number M16B
Molded Dual-In-Line Package (N)
Order Number COP8SAA716N8 or COP8SAA716N9
NS Package Number N16A
www.national.com53
Page 54
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
COP8SA Family
Molded SO Wide Body Package (WM)
Order Number COP8SAA720M9, COP8SAB720M9, COP8SAC720M9
COP8SAA720M8, COP8SAB720M8 or COP8SAC720M8
NS Package Number M20B
Molded Dual-In-Line Package (N)
Order Number COP8SAA720N9, COP8SAB720N9, COP8SAC720N9,
COP8SAA720N8, COP8SAB720N8 or COP8SAC720N8
NS Package Number N20A
www.national.com 54
Page 55
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
COP8SA Family
28-Lead Hermetic Dual-In-Line Package EPROM (D)
Order Number COP8SAC728Q3
NS Package Number D28JQ
www.national.com55
Page 56
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
COP8SA Family
Molded SO Wide Body Package (WM)
Order Number COP8SAA728M9, COP8SAB728M9, COP8SAC728M9,
COP8SAA728M8, COP8SAB728M8 or COP8SAC728M8
NS Package Number M28B
Molded Dual-In-Line Package (N),
Order Number COP8SAA728N9, COP8SAB728N9, COP8SAC728N9,
COP8SAA728N8, COP8SAB728N8 or COP8SAC728N8
NS Package Number N28B
www.national.com 56
Page 57
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
COP8SA Family
28 Lead Chip Scale Package (SLB)
Order Number COP8SAA7SLB9, COP8SAB7SLB9 or COP8SAC7SLB9
NS Package Number SLB28A
www.national.com57
Page 58
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
COP8SA Family
40-Lead Hermetic DIP EPROM (D)
Order Number COP8SAC740Q3
NS Package Number D40KQ
Molded Dual-In-Line Package (N)
Order Number COP8SAC740N9 or COP8SAC740N8
NS Package Number N40A
www.national.com 58
Page 59
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
COP8SA Family
44-Lead EPROM Leaded Chip Carrier (EL)
Order Number COP8SAC744Q3
NS Package Number EL44C
www.national.com59
Page 60
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)
Molded Dual-In-Line Package (N)
Order Number COP8SAC744V9 or COP8SAC744V8
NS Package Number V44A
with 1k to 4k Memory, Power On Reset, and Very Small Packaging
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.
2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
National Semiconductor Corporation
Americas
COP8SA Family, 8-Bit CMOS ROM Based and One-Time Programmable (OTP) Microcontroller
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com
www.national.com
National Semiconductor Europe
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790
National Semiconductor Asia Pacific Customer Response Group
Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com
National Semiconductor Japan Ltd.
Tel: 81-3-5639-7560 Fax: 81-3-5639-7507
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use