Datasheet CN-0240 Datasheet (ANALOG DEVICES)

Circuit Note

High Common-Mode Voltage Difference
Amplifier

Precision, Low Noise, CMOS, Dual, Rail-to­Rail Output Op Amp

Precision, Selectable Gain, Fully Differential
Funnel Amplifier

Quad-Channel Isolator with Integrated

5 V, Low Noise, High Accuracy, XFET
Voltage Reference

Σ-Δ ADC

Rev. 0

Circuits from the Lab™ circuits from Analog Devices have been designed and built by Analog Devices

g practices have been employed in the design and construction of

each circuit, and their function and performance have been tested and verified in a lab environment at

suitability and applicability for your use and application. Accordingly, in no event shall Analog Devices
be liable for direct, indirect, special, incidental, consequential or punitive damages due to any cause
whatsoever connected to the use of any Circuits from the Lab circuits. (Continued on last page)

Fax: [phone] ©2012 Analog Devices, Inc. All rights reserved.

5V_REF

2.5V_CM

5V

V

SHUNT

= 0V TO 100mV

NOTE: SIGNAL VOLTAGES
SHOWN FOR POSITIVE SOURCE

0V TO

−1V

0V TO 10V

2.5V TO

4.5V

15V

5V

15V

15V

−15V

LOAD

+

−

2.5V TO

0.5V

1kΩ

10kΩ

10kΩ

1kΩ

10kΩ

10kΩ

+

−

REF+

REF−

+

−

+

–

−15V

+IN 0.4×

–IN 0.4×

+

–

VOCM

AD629

1/2

AD8622

1/2

AD8622

ADR435

AD8475 AD7170

AIN+

REFIN+

AIN−

REFIN−

GND

VDD

SCLK

PDSTR

DOUT

V

OA

V

OB

V

IC

V

IA

V

IB

V

OC

VDD1V

ISO

GND

1

GND

ISO

5V

1

0V TO

100mV

V

SHUNT

V

SOURCE

R

SHUNT

ADuM5402

10154-001

CN-0240

Devices Connected/Referenced

AD629

AD8622

AD8475

ADuM5402

DC-to-DC Converter

Circuits from the Lab™ reference circuits are engineered and
tested for quick and easy system integration to help solve today’s
analog, mixed-signal, and RF design challenges. For more
information and/or support, visit www.analog.com/CN0240.

ADR435

AD7170

12-Bit, Low Power

Bidirectional Isolated High-Side Current Sense with 270 V Common-Mode Rejection

EVALUATION AND DESIGN SUPPORT

Circuit Evaluation Boards

CN-0240 Circuit Evaluation Board (EVAL-CN0240-SDPZ)
System Demonstration Platform (EVAL-SDP-CB1Z)

Design and Integration Files
Schematics, Layout Files, Bill of Materials

CIRCUIT FUNCTION AND BENEFITS

This circuit, shown in Figure 1, monitors bidirectional current
from sources with dc voltages of up to ±270 V with less than 1%
linearity error. The load current passes through a shunt resistor,
which is external to the circuit. The shunt resistor value is
chosen so that the shunt voltage is approximately 100 mV at
maximum load current.

engineers. Standard engineerin

room temperature. However, you are solely responsible for testing the circuit and determining its

Figure 1. High Common-Mode Voltage Bidirectional Isolated Current Monitor (All Connections and Decoupling Not Shown)

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: [phone]

www.analog.com

CN-0240 Circuit Note

1

2

3

4

8

7

6

5

21.1kΩ

380kΩ

380kΩ

380kΩ

20kΩ

REF(–)

–IN

+IN

–V

S

NC

+V

S

OUTPUT

REF(+)

AD629

NC = NO CONNECT

10154-002

POWER SUPPLY VOLTAGE (±V)

COMMON-MODE VOLTAGE (±V)

400

360

320

280

240

200

160

120

80

40

0

0 2 6 104 8 12 14 1816 20

TA = +25°C

TA = +85°C

TA = –40°C

10154-003

The AD629 amplifier accurately measures and buffers (G = 1) a
small differential input voltage and rejects large positive
common-mode voltages up to 270 V.

The dual AD8622 is used to amplify the output of the AD629 by
a factor of 100. The AD8475 funnel amplifier attenuates the
signal (G = 0.4), converts it from single-ended to differential,
and level shifts the signal to satisfy the analog input voltage
range of the AD7170 sigma-delta ADC.

Galvanic isolation is provided by the ADuM5402 quad channel
isolator. This is not only for protection but also to isolate the
downstream circuitry from the high common-mode voltage. In
addition to isolating the output data, the ADuM5402 digital
isolator can supply isolated +5.0 V for the circuit.

The measurement result from the AD7170 is provided as a
digital code utilizing a simple 2-wire, SPI-compatible serial
interface.

This combination of parts provides an accurate high voltage
positive and negative rail current sense solution with a small
component count, low cost, and low power.

CIRCUIT DESCRIPTION

The circuit is designed for a full-scale shunt voltage of 100 mV
at maximum load current I
resistor is R

= (500 mV)/(I

SHUNT

The AD629, shown in Figure 2, is a difference amplifier
designed with internal thin film resistors allowing continuous
common-mode signals up to ±270 V with transient protection
to ±500 V. For REF(+) and REF(−) grounded, the signal on the
+IN terminal is attenuated by a factor of 20. The signal is then
amplified by a noise gain of 20, restoring the original amplitude
at the output.

Figure 2. AD629 High Common-Mode Voltage Difference Amplifier

The CMRR is 77 dB minimum @ 500 Hz for the AD629A, and
86 dB minimum @ 500 Hz for the AD629B.

In order to maintain the desired common-mode rejection, there
are several important conditions to meet. First, the ability of

. Therefore, the value of the shunt

MAX

).

MAX

the part to reject these common-mode signals is determined by
the power supply voltage as shown in Figure 3. Failure to
implement dual supplies of a sufficient voltage will reduce the
common-mode rejection.

Figure 3. AD629 Common-Mode Voltage Range vs. Power Supply Voltage

Secondly, the AD629 should only be operated in the unity gain
mode using the internal matched thin film resistors. Changing
the gain with external resistors will degrade the common-mode
rejection due to mismatch errors.

The AD8622 is a CMOS low power, precision, dual, rail-to-rail
output op amp used primarily for amplifying the signal of
interest.

By cascading two inverting gain stages with a gain of –10, the
100 mV full-scale output of the AD629 is amplified by a factor
of 100 yielding a 10 V full-scale signal. These values can be
either positive or negative, depending on the direction of the
current.

The dual supplies of the AD8622 allow both the input and
output signals to swing above and below ground as required to
measure bidirectional input currents.

In the final stage of the signal chain before conversion into a
digital word, the AD8622 output voltage is conditioned to fit the
analog input voltage range of the ADC.

The AD8475 "funnel amplifier," shown in Figure 4, provides two
optional attenuation factors (0.4 and 0.8). In addition, the signal
is converted into a differential one, and the common-mode
voltage at the output is determined by the voltage on the VOCM
pin. With a single 5 V supply, the analog input voltage range is
±12.5 V (for a single-ended input).

Rev. 0 | Page 2 of 5

Circuit Note CN-0240

+IN 0.8x10+IN 0.4x9–V

1.25kΩ

1.25kΩ

1.25kΩ

1.25kΩ

–IN 0.8x1–IN 0.4x

NC = NO CONNECT

Figure 4. AD8475 Funnel Amplifier

S

NC7–OUT

8

6

1kΩ

AD8475

1kΩ

3

2

+V

4

5

S

+OUT

VOCM

10154-004

As shown in Figure 1, the output common-mode voltage is set
at 2.5 V by a resistor divider driven by the ADR435 reference
output of 5 V.

The primary source of noise in the system is the output noise of
the AD629 of 15 µV p-p in the 0.1 Hz to 10 Hz bandwidth. For
a 100 mV full-scale signal, this corresponds to a noise-free code
resolution of

Noise Free Code Resolution =



log




2





mV100



2



m

V15



( )

==

bits7.126666log

The input noise of the AD8622 is only 0.2 µV p-p, which is
negligible compared to the AD629. The output noise of the

AD8475 is 2.5 µV p-p, which is also negligible at that point

where the full-scale signal level is 4 V p-p.

Notice that the power supply voltage for the AD7170 is supplied
by the isolated power output (+5.0 V

) of the ADuM5402 quad

ISO

isolator.

The reference voltage for the AD7170 is supplied by the

ADR435 precision XFET® reference. The ADR435 has an initial

accuracy of ±0.12% (A grade), and a typical temperature
coefficient of 2 ppm/°C. The ADR435 has a wide operating
range (7.0 V to 18.0 V) a

er source.

pow

nd utilizes the +15.0 V rail for a

Although it is possible to operate both the AD7170 VDD and
REFIN(+) from the 5.0 V power supply, using a separate
reference provides better accuracy.

The input voltage to the AD7170 ADC is converted into an
offset binary code at the output of the ADC. The ADuM5402
provides the isolation for the DOUT data output, the SCLK
input, and the

PDRST

input. Although the isolator is optional,

it is recommended to protect the downstream digital circuitry

from the high common-mode voltage in the case of a fault
condition.

The code is processed in the PC by using the SDP hardware
board and LabVIEW software.

Figure 5 shows a comparison between the code seen at the
output of the ADC recorded by LabVIEW and an ideal code
calculated based on a perfect system. The plots show how the
circuit achieves an end-point linearity error of less than 0.5%
over the entire input voltage range (−100 mV to +100 mV).
The offset error and gain error can be removed using software
calibration if desired.

–69.976

–80.178

–90.595

–100.430

0

–0.5

–1.0

–1.5

–2.0

–2.5

–3.0

–3.5

–4.0

CODE ERROR (%)

4000

3500

3000

2500

2000

CODE

1500

1000

500

0

Figure 5. Plot of Actual Code, Ideal Code, and %Error vs. Shunt Voltage

IDEAL CODE

ERROR =
100 × (ACTUAL CODE − IDEAL CODE) ÷ 4096

99.909

90.242

80.195

69.942

ACTUAL CODE

60.283

50.030

39.983

29.729

20.087

SHUNT VOLTAGE (mV)

10.049

–0.535

–10.229

–19.867

–30.106

–40.352

–50.198

–60.249

PCB Layout Considerations

In any circuit where accuracy is crucial, it is important to
consider the power supply and ground return layout on the
board. The PCB should isolate the digital and analog sections as
much as possible. This PCB was constructed in a 4-layer stack
up with large area ground plane layers and power plane
polygons. See the MT-031 Tutorial for more discussion on
layout and grounding and the MT-101 Tut o r ia l for information
on decoupling techniques.

The power supply to the AD7170 and ADuM5402 should be
decoupled with 10 µF and 0.1 µF capacitors to properly suppress
noise and reduce ripple. The capacitors should be placed as
close to the device as possible with the 0.1 µF capacitor having a
low ESR value. Ceramic capacitors are advised for all high
frequency decoupling.

Care should be taken in considering the isolation gap between
the primary and secondary sides of the ADuM5402. The

EVA L-CN0240-SDPZ board maximizes this distance by pulling

back any polygons or components on the top layer and aligning
them with the pins on the ADuM5402.

Power supply lines should have as large a trace width as possible
to provide low impedance paths and reduce glitch effects on the

10154-005

Rev. 0 | Page 3 of 5

CN-0240 Circuit Note

supply line. Clocks and other fast switching digital signals
should be shielded from other parts of the board by digital
ground.

A complete design support package for this circuit note,
including complete schematics and board layouts, can be
found at www.analog.com/CN0240-DesignSupport.

COMMON VARIATIONS

There are a number of solutions available for high-side sensing
of positive and negative sources. IC solutions using current
sense amplifiers, difference amplifiers, or a combination of
these are available. See the circuits described in the following
circuit notes: CN0100, CN0188, CN0218.

“High-Side Current Sensing: Difference Amplifier vs. Current
Sense Amplifier,” Analog Dialogue, January 2008, describes the

use of current sense and difference amplifiers. The article is
available at www.analog.com/HighSide_CurrentSensing.

The following URLs link to Analog Devices products useful in
solving the current sense problem:

Current sense amplifiers: www.analog.com/CurrentSenseAmps
Difference amplifiers: www.analog.com/DifferenceAmps
Instrumentation amplifiers: www.analog.com/InstrumentationAmps

CIRCUIT EVALUATION AND TEST

WARNING! HIGH VOLTAGE. THIS CIRCUIT MAY
CONTAIN LETHAL VOLTAGES. DO NOT OPERATE,
E VA LUA T E, OR TEST THIS CIRCUIT, OR BOARD
ASSEMBLY, UNLESS YOU ARE A TRAINED
PROFESSIONAL, WHO IS QUALIFIED TO HANDLE HIGH
VOLTAGE CIRCUITRY. BEFORE APPLYING POWER, YOU
MUST BE FAMILIAR WITH THE CIRCUITRY AND ALL
REQUIRED PRECAUTIONS FOR WORKING WITH HIGH
VOLTAGE CIRCUITS.

This circuit uses the E VA L-CN0240-SDPZ circuit board and the

EVA L-SDP-CB1Z System Demonstration Platform (SDP)

evaluation board. The two boards have 120-pin mating
connectors, allowing for the quick setup and evaluation of the
circuit’s performance. T he EVAL -CN0240-SDPZ board contains
the circuit to be evaluated, as described in this note, and the
SDP evaluation board is used with the CN0240 evaluation
software to capture the data from the EVA L-CN0240-SDPZ
circuit board.

Equipment Needed

• PC with a USB port and Windows® XP or Windows Vista®

(32-bit), or Windows® 7 (32-bit)

• EVA L-CN0240-SDPZ circuit evaluation board

• EVA L-SDP-CB1Z SDP evaluation board

• CN0240 evaluation software

• Power supply: +6 V @ 1 A, or +6 V “wall wart”

Rev. 0 | Page 4 of 5

• Dual power supply: ±15 V@ 10 mA

• Shunt resistor with maximum voltage of 100 mV at the

maximum load current.

• Source voltage and electronic load

Getting Started

Load the evaluation software by placing the CN0218 evaluation
software disc in the CD drive of the PC. Using "My C omputer,"
locate the drive that contains the evaluation software disc and
open the Readme file. Follow the instructions contained in the
Readme file for installing and using the evaluation software.

Functional Block Diagram

See Figure 1 of this circuit note for the circuit block diagram
and the E VAL -CN0240-SDPZ-SCH pdf file for the circuit
schematics. This file is contained in the CN0240 Design

Support Package.

Setup

Connect the 120-pin connector on the E VA L-CN0240-SDPZ
circuit board to the connector marked “CON A” on the

EVA L-SDP-CB1Z evaluation (SDP) board. Nylon hardware

should be used to firmly secure the two boards, using the holes
provided at the ends of the 120-pin connectors.

Connect a shunt resistor (R

) across the J4 input terminals

SHUNT

with a load to ground as indicated in Figure 1. With power to
the supply off, connect a +6 V power supply to the pins marked
“+6 V” and “GND” on the board. If available, a +6 V "wall wart

an be connected to the barrel connector on the board and used

c
in place of the +6 V power supply. Connect the USB cable
supplied with the SDP board to the USB port on the PC.
Note: Do not connect the USB cable to the mini USB connector
on the SDP board at this time.

It is important to connect the system ground and the PCB
isolated ground to guarantee correct voltage levels and
operation. Test point 31 and test point 32 give access to the
GND_ISO required to properly make this connection.

Lastly, before applying any high voltage to connector J4, be
certain the ±15 V supply (J5) is properly connected and has
been turned on. If this supply is not active, any high voltage
could potentially damage U2, the AD629, as well as several
other components on the PCB.

Test

Apply power to the +6 V supply (or “wall wart”) connected to
the EVA L-CN0240-SDPZ circuit board. Connect the ±15 V
supplies to the E VAL-CN0240-SDPZ board U12 three-terminal
screw connector. Launch the evaluation software and connect
the USB cable from the PC to the USB mini-connector on the
SDP board.

"

Circuit Note CN-0240

(Continued from fi rst page) Circuits from the Lab circuits are intended only for use with Analog Devices products and are the intellectual property of Analog Devices or its licensors. While you

reserves the right to change any Circuits from the Lab circuits at any time without notice but is under no obligati on to do so.

registered trademarks are the property of their respective owners.

Once USB communications are established, the SDP board
can be used to send, receive, and capture serial data from the
EVA L-CN0240-SDPZ board. Data can be recorded for various
values of load current as the electronic load is stepped.

Information and details regarding how to use the evaluation
software for data capture can be found in the CN0240
evaluation software Readme file.

Information regarding the SDP board can be found in the

SDP User Guide.

LEARN MORE

CN0240 Design Support Package:

www.analog.com/CN0240-DesignSupport

Sino, Henri. “High-Side Current Sensing: Difference Amplifier

vs.Current-Sense Amplifier,” Analog Dialogue 42-01,
January (2008).

Cantrell, Mark. Application Note AN-0971, Recommendations

for Control of Radiated Emissions with isoPower Devices.
Analog Devices.

Chen, Baoxing, John Wynne, and Ronn Kliger. High Speed

Digital Isolators Using Microscale On-Chip Transformers,
Analog Devices, 2003.

Chen, Baoxing. iCoupler® Products with isoPower™ Technology:

Signal and Power Transfer Across Isolation Barrier Using
Microtransformers, Analog Devices, 2006

Chen, Baoxing. “Microtransformer Isolation Benefits Digital

Control.” Power Electronics Technology. October 2008.

Ghiorse, Rich. Application Note AN-825, Power Supply

Considerations in iCoupler® Isolation Products, Analog
Devices.

Krakauer, David. “Digital Isolation Offers Compact,

Low-Cost Solutions to Challenging Design Problems.”
Analog Dialogue. Volume 40, December 2006.

MT-022 Tutorial, ADC Architectures III: Sigma-Delta ADC

Basics, Analog Devices.

MT-023 Tutorial, ADC Architectures IV: Sigma-Delta ADC

Advanced Concepts and Applications, Analog Devices.

MT-031 Tutorial, Grounding Data Converters and Solving the

Mystery of "AGND" and "DGND," Analog Devices.

MT-101 Tutorial, Decoupling Techniques, Analog Devices.

Wayne, Scott. “iCoupler

®

Digital Isolators Protect RS-232,
RS-485, and CAN Buses in Industrial, Instrumentation,
and Computer Applications.” Analog Dialogue. Volum e 39,
October 2005.

Data Sheets and Evaluation Boards

CN-0240 Circuit Evaluation Board (EVAL-CN0240-SDPZ)

System Demonstration Platform (EVAL-SDP-CB1Z)

AD629 Data Sheet

AD8622 Data Sheet

AD8475 Data Sheet

AD7170 Data Sheet

AD7170 Evaluation Board

ADR435Data Sheet

ADuM5402 Data Sheet

ADuM5402 Evaluation Board

REVISION HISTORY

2/12—Revision 0: Initial Version

may use the Circuits fr om the Lab circuits in the design of your product, no other license is granted by implication or otherwise under any patents or other intellectual property by
application or use of the Circuits from the Lab circuits. Information furnished by Analog Devices is believed to be accurate and reliable. However, "Circuits from the Lab" are supplied "a s is"
and without warranties of any kind, express, implied, or statutory including, but not limited to, any implied warranty of merchantability, noninfringement or fitness for a particular
purpose and n o responsibility is assumed by Analog Devices for their use, nor for any infringements of patents or other rights of third parties that may result from their use. Analog Devices

©2012 Analog Devices, Inc. All rights reserved. Trademarks and

CN10154-0-2/12(0)

Rev. 0 | Page 5 of 5