Datasheet CM10S2025, CM10S1525, CM10S1520, CM10S1030, CM10S1020 Datasheet (CPCLA)

Features Description

• Small size

• SMT-compatible

• Easily formed leads

• Sputtered ruthenium contacts

• Hermetically sealed contacts

• Fast switching speed — up to 500Hz

• Wide range of available magnetic sensitivities

• Superior mechanical strength

• Enhanced for better auto placement

Clare's Molded Mini DYAD dry reed switches are ideally
suited for small switching signal applications. This switch
has sputtered tuthenium contacts and an extraordinary
seal strength, achieved by a patented laser sealing of the
glass. In a low level or dry switching environments, both
switches typically provide >1 billion operations. The
switches have hermetically sealed contacts and offer a
wide range of available magnetic sensitivities. In addition,
the molding process provides a solid plastic outer shell.
This plastic shell provides superior mechanical strength,

Applications

• Security

eliminates concerns over handling glass switches, and
provides an ideal solution for high speed, automated
assembly environments.

− Proximity sensing

− Smoke alarms

• Automotive

− Level sensor

− Lamp current sensor

• Relays

Ordering Information

A complete part number is represented by the digits to the
right. For example, CM10S2030 is a MOLDED MINI­DYAD™ with a minimum operate value of 10NI and a
maximum of 30NI. Refer to the switch operating specifica­tion charts for available ranges. Special ranges are available
upon request.

"S" for straight switch
blank for SMT

Molded Mini-DYAD

CM10

CM10 S XX XX

Maximum
operate value

Minimum
operate value

™

Standard Test Coil

The magnetic force (expressed in NI, AT or Ampere Turns) required to cause the reed switch contacts to
close is called the pull-in or operate value.

CM10

Part # Coil - 1
Coil definition NARM1 CTC01
Coil resistance 1200Ω
Number of turns 5,000
Wire size (nom. diameter) 0.0399mm (AWG 46)
Bobbin diameter (inside coil) 3.96mm
Winding length 10.4mm

(1)

Consult factory for test procedure.
The reed switch shall be placed in the test coil with the gap centered in the core of the coil winding.
Test leads and their clips must be non-magnetic.
The longitudinal axis of the test coil and the test switch shall be vertical.

Surface Mount Molded Mini-DYAD
Refer to operating characteristics table for complete part number.

Molded Mini-DYAD

Part # Operate Range (NI)

CM10S1015 10 to 15
CM10S1020 10 to 20
CM10S1030 10 to 30
CM10S1520 15 to 20
CM10S1525 15 to 25
CM10S2025 20 to 25

Molded Mini-DYAD

Part # Operate Range (NI)

CM10-2308 10 to 15
CM10-2288 10 to 20
CM10-2339 10 to 30
CM10-2285 15 to 20
CM10-2289 15 to 25
CM10-2286 20 to 25

1

Tolerance = ± 1.5NI

2

Full Blade Sensitivity

3

Surface Mount Switches are packaged 3,000 parts per reel

TM

1

TM

Surface Mount

1,2,3

DS-CM10-R1

www.clare.com

1

Molded Mini-DYAD

CM10

™

Absolute Maximum Ratings (@ 25˚ C)

Parameter Min Typ Max Units

Switching Voltage
CM10 - Molded Mini-DYAD
Switching Current
CM10 - Molded Mini-DYAD
Carry Current
CM10 - Molded Mini-DYAD

™

- - 200 Volts

™

- - 0.5 Amps

™

- - 2 Amps

Absolute Maximum Ratings are stress ratings. Stresses
in excess of these ratings can cause permanent damage
to the device. Functional operation of the device at these
or any other conditions beyond those indicated in the
operational sections of this data sheet is not implied.
Exposure of the device to the absolute maximum ratings
for extended period may degrade the device and effect
its reliability.

Switching Frequency
CM10 - Molded Mini-DYAD

™

- - 500 Hz

Contact Resistance

™

CM10 - Molded Mini-DYAD

(See detailed specifications for more information.)

- -0 100 mΩ

Specifications

All parameters are at 25°C unless otherwise stated.

PARAMETER CONDITIONS SYMBOL MIN TYP MAX UNITS

Contact Ratings

Operate ampere turns range Full Blade Tolerance = ± 1.5NI AT 10 - 30 NI
Release ampere turns range Full Blade Tolerance = ± 1.5NI AT 5 - 30 NI
Switching Voltage Max DC/PeakAC Resistive V
Switching Current Max DC/PeakAC Resistive I
Carry Current Max DC/PeakAC Resistive I

L

L

C

Contact Rating Max DC/PeakAC Resistive - - - 10 VA
Life Expectancy 1V, 10mA Signal Level - - 1000 - x10

10V, 10mA Low Level - - 500 - -x10

50V, 100mA Telecom Load - - 2 - x10

100V, 100mA Rated Loads - - 2 - x10

Static Contact Resistance 50mV, 10mA

(1)

CR - 70 100 Ω

Contact Material - - Ru - -

Switch Specifications

Insulation Resistance

(2)

100V, 25°C, 40% RH IR 10
Capacitance Across Open Contacts - - 0.3 - pF
Dielectric Strength
Operate Time, At nominal coil voltage, T

(5)

Between Contacts - 250 300 - VDC/Peak AC

OP

including bounce 10Hz Square Wave

Release Time Zener-Diode Suppression

(3)

T

REL

Environmental Ratings

Storage Temperature T
Operating Temperature T

A

O

Soldering Temperature - - - +265 ˚C

- - 200 VDC

- - 500 mAmps

- - 2.0 Amps

9

10

11

- Ω

- - 0.5 ms

- - 0.1 ms

-40 - +125 ˚C

-40 - +125 ˚C

6

Ops

6

Ops

6

Ops

6

Ops

(1)

Contact resistance measured with 4 terminal method, 1.1" between test leads

(2)

>1012 Ω is available upon request

(3)

A 24V zener in series with a diode across the coil

(4)

Use caution not to exceed vibration resistance limits while ultrasonically cleaning. Contact Clare, Inc.
Engineering for more details/ recommendations

(5)

15 ampere turn minimum

2

www.clare.com

Rev. 1

Mechanical Dimensions

Molded Mini-DYAD

CM10

™

Rev. 1

www.clare.com

Dimensions

mm

(inches)

3

Worldwide Sales Offices

CLARE LOCATIONS

Clare Headquarters
78 Cherry Hill Drive
Beverly, MA 01915
Tel: [phone]
Fax: [phone]
Toll Free: 1-800-27-CLARE

Clare Switch Division
4315 Earth City Expresssway
St. Louis, MO 63045
Tel: [phone]
Fax: [phone]

Clare Micronix Division
145 Columbia
Aliso Viejo, CA 92656-1490
Tel: [phone]
Fax: [phone]

SALES OFFICES

AMERICAS

Americas Headquarters

Clare
78 Cherry Hill Drive
Beverly, MA 01915
Tel: [phone]
Fax: [phone]
Toll Free: 1-800-27-CLARE

Eastern Region

Clare
P.O. Box 856
Mahwah, NJ 07430
Tel: [phone]
Fax: [phone]
Toll Free: 1-800-27-CLARE

Central Region

Clare Canada Ltd.
3425 Harvester Road, Suite 202
Burlington, Ontario L7N 3N1
Tel: [phone]
Fax: [phone]

Western Region

Clare
1852 West 11th Street, #348
Tracy, CA 95376
Tel: [phone]
Fax: [phone]
Toll Free: 1-800-27-CLARE

EUROPE

European Headquarters

CP Clare nv
Bampslaan 17
B-3500 Hasselt (Belgium)
Tel: [phone]
Fax: [phone]

France

Clare France Sales
Lead Rep
99 route de Versailles
91160 Champlan
France
Tel: [phone]
Fax: [phone]

Germany

Clare Germany Sales
ActiveComp Electronic GmbH
Mitterstrasse 12
85077 Manching
Germany
Tel: [phone]
Fax: [phone]

Italy

C.L.A.R.E.s.a.s.
Via C. Colombo 10/A
I-20066 Melzo (Milano)
Tel: [phone]
Fax: [phone]

Sweden

Clare Sales
Comptronic AB
Box 167
S-16329 Spånga
Tel: [phone]
Fax: [phone]

United Kingdom

Clare UK Sales
Marco Polo House
Cook Way
Bindon Road
Taunton
UK-Somerset TA2 6BG
Tel: [phone]
Fax: [phone]

ASIA PACIFIC

Asian Headquarters

Clare
Room N1016, Chia-Hsin, Bldg II,
10F, No. 96, Sec. 2
Chung Shan North Road
Taipei, Taiwan R.O.C.
Tel: [phone]
Fax: [phone]

http://www.clare.com

Clare cannot assume responsibility for use of any circuitry other
than circuitry entirely embodied in this Clare product. No circuit
patent licenses nor indemnity are expressed or implied. Clare re­serves the right to change the specification and circuitry, without
notice at any time. The products described in this document are not
intended for use in medical implantation or other direct life support
applications where malfunction may result in direct physical harm,
injury or death to a person.

Canada

Clare Canada Ltd.
3425 Harvester Road, Suite 202
Burlington, Ontario L7N 3N1
Tel: [phone]
Fax: [phone]

Specification: PB-CM10-R1
©Copyright 2001
Molded Ultra-Mini DYAD™, Molded Mini DYAD™, and
Molded DYAD® are trademarks of Clare, Inc.
All rights reserved. Printed in USA.
4/23/01