Page 1
PRELIMINARY
Q3 2003
1.6 U High Chassis (2.74”)
•
Optional 19” Rack allows up to 3 Modules
•
Universal AC Input with Active PFC
•
World Wide Safety Approvals & CE Mark
•
Internal Or-ing Diodes for
Hot Swap/Redundancy
•
1000 W Low Line/1500 W
High Line Operation
Input
Input Voltage • 90-264 VAC
Input Frequency • 47-63 Hz
Power Factor • 0.95 minimum
Harmonic Current • Meets EN6100-3-2
Inrush Current • 35 A max per module
(ETSI 300 132 compliant)
Input Protection • Two 15 A fuse per module
Input Current • 13.5 A rms at 90 VAC
10.5 A rms at 180 VAC
Output
Output Voltage • -54 VDC
Output Power • 1000 W <180 VAC input
1500 W >180 VAC input
Minimum Load • 0 minimum load for all outputs
Line/Load Regulation • ±5%
Ripple & Noise • ±1% pk-pk maximum
(ETSI 300 132 compliant)
Transient Response • 1V max deviation, 4ms recovery
time for a 50% load change
Overvoltage • -59 VDC (±1 VDC)
Protection recycle input to reset
Overcurrent • Current limited to 36 A
Protection
Status/Signals
Voltage Control • -40 to -59 VDC with digital interface
Remote on/off • Turn on with 10kohm resistor on
ON/OFF pin
Current Monitor • Analog signal 1V per 10A
AC OK • Active High = Good
DC OK • Active High = Good
Missing Module • Active High = Good
Load Share • Single Wire Connection ±10% accuracy
LED Indicators • 4 LED’s for AC Good, DC Good,
Over-Temp & OVP
General
Efficiency • 91% typical at full load
MTBF (supply) • 200k hrs demonstrated at 50 °C
full load
Size • 12.70” x 5.00” x 2.74”
Weight • 7.0 Ibs (3.2 kg)
Environmental
Operating • -40 °C to 55 °C, Full power to 55 °C
Temperature derate from 55 °C to 70 °C at 2.5%/°C
Cooling • Horizontal, front to back with
internal fans
Humidity • <95% RH, non-condensing
Storage Temperature • -40 °C to +85 °C
Altitude • 7,382 feet (2,250 meters)
Shock • IEC68-2-27, Mil-STD-810E, 20G
Vibration • IEC68-2-64, 20-200HZ, 30min, 6G rms
Telecordia • GR-63-CORE, GR-487-CORE (NEBS
Shock & Vibration, Seismic Zone 4)
EMC & Safety
Safety Approvals • UL1950, TUV EN60950 / IEC 950
CSA 22.2-950 CE Mark LVD
EMI/EMC • EN55022 Class B, FCC 20780 Part 15,
Subpart J Class B
Immunity and Surge • EN61000-4-2 Criteria B compliant
EN61000-4-3 Criteria A compliant
EN61000-4-4 Criteria B compliant
EN61000-4-5 Criteria A compliant
EN61000-4-6 Criteria A compliant
EN61000-4-11 Criteria B & C compliant
1500 Watts
CDP1K5 Series
AC/DC Front End/Rectifier
Specification
•
•
•
Intelligent Design Quality Product
XPiQ inc.
* Preliminary datasheet - see website for current specs
PH: 508 429.9883
FAX: 800 226.2100
Email: sales@xpiq.com
Holliston, MA 01746 USA
www.XPiQ.com
CDP1K5.qxd 6/6/03 4:06 pm Page 1
Page 2
1. All Models offer front to rear air-flow.
2. Class I Protective ground must be connected to protective conductor.
3. Either the “+” or the “-” power terminal may be grounded.
4. Supply is off unless a 10kohm pull-up resistor is present between the on/off pin (b19) and the 0V signal (c19).
Notes
Mechanical Details - Module
Maximum Output Adjustment Model
Power Voltage Range Number
1000 Watts <180 VAC Input
-54 VDC -40 to -59 VDC CDP1K5PS48
1500 Watts >180 VAC Input
OUTPUT VOLTAGE & CURRENT RATINGS CDP1K5
•
Pin Description Pin Description Pin Description
a1-a7 Out- (-48V) b1-b7 Out- (-48V) c1-c7 Out- (-48V)
a8 Do not connect b8 Do not connect c8 Do no connect
a9-a15 Out+ (+0V) b9-b15 Out+ (+0V) c9-c15 Out+ (+0V)
a16 DC OK b16 Programming c16 Current
Monitoring
a17 Do not connect b17 AC OK c17 Sharing
a18 Do not connect b18 Temperature OK c18 AC High
a19 Missing module b19 Remote ON/OFF c19 OV signal
a20 Removed b20 Removed c20-c22 Removed
a22 b22
a23 Line b23 Line c23-c24 Line
a24 b24
a25 Removed b25 Removed c25-c26 Removed
Optional 3 bay 19" Rack & Battery Controller
c
b
a
1
32
* Preliminary datasheet - see website for current specs
PH: 508 429.9883
FAX: 800 226.2100
Email: sales@xpiq.com
Holliston, MA 01746 USA
www.XPiQ.com
CDP1K5.qxd 6/6/03 4:06 pm Page 2
Loading...