Datasheet C052C109D1G5CA Datasheet (KEMET)

© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, [phone]20

CERAMIC MOLDED AXIAL & RADIAL

PERFORMANCE CHARACTERISTICS

GENERAL

Working Voltage:

C0G – 50, 100 & 200 Volts
X7R – 50, 100 & 200 Volts

Temperature Characteristics:

C0G – 0 ±30 PPM/°C from -55°C to +125°C
X7R – ±15% from -55°C to +125°C

Capacitance Tolerance:

C0G – ±0.5 pF, ±1%, ±2%, ±5%, ±10%, ±20%

(±0.5 pF is tightest available tolerance)

X7R – ±10%, ±20%, -0 +100%, -20% +80%

Construction:

Monolithic block of ceramic dielectric with interdigitated
internal electrodes, encapsulated in a molded case, and
having axial or radial leads. Meets flame test requirements
of UL Standard 94V-0.

Terminal Strength:

EIA-198 Method 303 Condition A (2.2 kg)

ELECTRICAL

Capacitance:

Within specified tolerance when measured with 1 volt rms
at 1 kHz (1000 pF or less at 1 MHz for C0G).

Dissipation Factor:

25°C at 1 kHz (1000 pF or less at 1 MHz for C0G).
C0G – .15% maximum
X7R – 2.5% maximum

Insulation Resistance:

After 2 minutes electrification at 25°C and rated voltage
C0G – 100K megohms or 1000 megohm - µF, whichever

is less.

X7R – 100K megohms or 1000 megohm - µF, whichever

is less.

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current limited
to 50 mA at 25°C.

Life Test:

2000 hours at 200% of rated voltage at 125°C. Post-Test
limits at 25°C are:

Capacitance Change:

C0G – less than 3% or 0.25 pF, whichever is higher
X7R – ±20% of initial value

Dissipation Factor:

C0G – .25% maximum
X7R – 3.0% maximum

查询C052C109D1G5CA供应商

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current
limited to 50 mA.

ENVIRONMENTAL

Moisture Resistance:

MIL-STD-202, Method 106, or EIA-198, Method 204,
Condition A, except 20 cycles.

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Dielectric Withstanding Voltage:

250% of rated voltage for 5 seconds with current
limited to 50 mA.

Immersion Cycling:

MIL-STD-202, Method 104, Condition B. Post-Test limits
at 25°C are:

Insulation Resistance:

C0G – 10K megohms or 100 megohm - µF, whichever

is less

X7R – 10K megohms or 100 megohm - µF, whichever

is less

Solderability:

MIL-STD-202, Method 208, Sn62 solder, 245°C for 5 ±1/2
seconds.

Resistance to Soldering Heat:

MIL-STD-202, Method 210, Condition B (260°C, 10 secs).
Depth of immersion — to a minimum of .050" from the
capacitor body.

Lead Material:

Axial: Solder-coated copper clad steel

Radial: Solder-coated copper standard; 100% tin plated optional

© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, [phone] 21

CERAMIC MOLDED/AXIAL & RADIAL - STANDARD

Lead Dia.

.025

(+.004

-.002)

S

H

1.25
Min.

W

Center Line of leads
within .030" of Center
Line of case.

H

1.25
Min.

L

S

W

.045

Max.

L

C052 C062,

C512,
& C522

Lead Dia.

.025

(+.004

-.002)

DIMENSIONS—INCHES & (MILLIMETERS)

CASE MILITARY

SIZE EQUIVALENT STYLES

LD C

C114 .160 ± .010 (4.06 ± .25) .090 ± .010 (2.29 ± .25) .020, +.000, -.003 (.51, +.00, -.08)

C124 .250 ± .010 (6.35 ± .25) .090 ± .010 (2.29 ± .25) .020, +.000, -.003 (.51, +.00, -.08)

C192 .390 ± .010 (9.91 ± .25) .140 ± .010 (3.56 ± .25) .025, +.004, -.001 (.64, +.10, -.025)

C202 .500 ± .020 (12.70 ± .51) .250 ± .015 (6.35 ± .38) .025, +.004, -.001 (.64, +.10, -.025)

C222 .690 ± .030 (17.53 ± .76) .350 ± .020 (8.89 ± .51) .025, +.004, -.001 (.64, +.10, -.025)

CAPACITOR OUTLINE DRAWINGS — (AXIAL LEADS)

CC75, CCR75
CK12, CKR11

CC76, CCR76
CK13, CKR12

CC77, CCR77
CK14, CKR14

CC78, CCR78
CK15, CKR15

CC79, CCR79
CK16, CKR16

CAPACITOR OUTLINE DRAWINGS — (RADIAL LEADS)

DIMENSIONS—INCHES & (MILLIMETERS)

MILITARY S

CASE EQUIVALENT H L W LEAD

SIZE STYLES HEIGHT LENGTH WIDTH SPACING

C052 .190 ± .010 (4.83 ± .25) .190 ± .010 (4.83 ± .25) .090 ± .010 (2.29 ± .25) .200 ± .015 (5.08 ± .38)

C062 .290 ± .010 (7.37 ± .25) .290 ± .010 (7.37 ± .25) .090 ± .010 (2.29 ± .25) .200 ± .015 (5.08 ± .38)

C512 .480 ± .020 (12.19 ± .51) .480 ± .020 (12.19 ± .51) .140 ± .010 (3.56 ± .25) .400 ± .020 (10.16 ± .51)

C522 .480 ± .020 (12.19 ± .51) .480 ± .020 (12.19 ± .51) .240 ± .010 (6.10 ± .25) .400 ± .020 (10.16 ± .51)

CC05, CCR05
CK05, CKR05

CC06, CCR06
CK06, CKR06

CC07, CCR07

CC08, CCR08

For packaging information, see pages 39, 40 and 41.

Ceramic Molded

Axial/Radial - Standard

1.50 Min.
(38.10)

1.50 Min.
(38.10)

DL

C

CERAMIC MOLDED/AXIAL & RADIAL - STANDARD

© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, [phone]22

RADIAL CAPACITOR MARKING

C052C & C062C STANDARD MARKING

100V

K

0511

Voltage
KEMET
Date Code

BACK

C062

X7R

104K

FRONT

Style

Temperature Characteristic

Capacitance, Capacitance Tolerance

C512 & C522 STANDARD MARKING

KEMET

C512X7R

105K 50V

0532

KEMET
SIZE and Temperature Characteristic
Capacitance, Capacitance Tolerance, Voltage
Date Code

ORDERING INFORMATION

**

C

052

C

102

K

R

2

C

5

A

CERAMIC
*CASE SIZE

(See Table Below)

SPECIFICATION

Standard

C — Standard

CAPACITANCE

In picofarad code: First two digits are significant
figures and third is number of zeroes following
(except 9 indicates division by 10). Examples:

0.1 F = 100,000 pF = 104 and 9.1 pF = 919.
See tables for Standard Values.

CAPACITANCE TOLERANCE

Standard

M— ±20%
K — ±10%
J — ±5%

Standard tolerances for each Series are
shown in the repetitive parts lists.

*CASE SIZES

RADIAL AXIAL

C052 C114
C062 C124
C512 C192
C522 C202

C222

Others

H — ±3%
G — ±2%
F — ±1%
D — ±.5 pF

WORKING
VOLTAGE

1 — 100
2 — 200
5 — 50

**Part Number Example: C052C102K2R5CA (14 digits – no spaces)

F AILURE RATE

A — Not Applicable (Std.)

LEAD MA TERIAL

C — Standard

T — 100% Tin plated
(C052, C062 only)

INTERNAL CONSTRUCTION

5 — Standard

TEMPERATURE CHARACTERISTIC

Cap. Change With Temp.

KEMET EIA Temp. DC Bias

Designator Equivalent Range, °C Volta ge

G C0G -55 to ±30

(Ultra (NPO) +125 ppm/°C

Stable)

R X7R -55 to ±15%

(Stable) +125

Measured

Without

STANDARD C114C, C124C, C192C, C202C & C222C

AXIAL CAPACITOR MARKING

KC0G

101J
200V
0512

KEMET, Temperature Characteristic
Capacitance, Capacitance Tolerance
Voltage
Date Code

© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, [phone] 23

Ceramic Molded

Axial/Radial - Standard

CAPACITANCE KEMET

pF PART NUMBER

200 VOLT — C202 STANDARD C0G

5,600.0 C202C562(4)2G5CA
6,800.0 C202C682(4)2G5CA
8,200.0 C202C822(4)2G5CA

10,000.0 C202C103(4

)2G5CA
12,000.0 C202C123(4)2G5CA
15,000.0 C202C153(4)2G5CA
18,000.0 C202C183(4)2G5CA
22,000.0 C202C223(4)2G5CA

100 VOLT — C202 STANDARD C0G

10,000.0 C202C103(4

)1G5CA
12,000.0 C202C123(4)1G5CA
15,000.0 C202C153(4)1G5CA
18,000.0 C202C183(4)1G5CA
22,000.0 C202C223(4)1G5CA
27,000.0 C202C273(4)1G5CA
33,000.0 C202C333(4

)1G5CA

200 VOLT — C222 STANDARD C0G

27,000.0 C222C273(4

)2G5CA
33,000.0 C222C333(4)2G5CA
39,000.0 C222C393(4)2G5CA
47,000.0 C222C473(4)2G5CA

100 VOLT — C222 STANDARD C0G

39,000.0 C222C393(4

)1G5CA
47,000.0 C222C473(4)1G5CA
56,000.0 C222C563(4)1G5CA
68,000.0 C222C683(4)1G5CA
82,000.0 C222C823(4)1G5CA

100,000.0 C222C104(4)1G5CA

CERAMIC MOLDED/AXIAL – STANDARD

ULTRA-STABLE TEMPERATURE CHARACTERISTIC—C0G (NP0)

CAPACITANCE KEMET

pF PART NUMBER

200 VOLT — C124 STANDARD C0G

390.0 C124C391(4)2G5CA

470.0 C124C471(4)2G5CA

560.0 C124C561(4)2G5CA

100 VOLT — C124 STANDARD C0G

820.0 C124C821(4

)1G5CA

1,000.0 C124C102(4)1G5CA

200 VOLT — C192 STANDARD C0G

680.0 C192C681(4

)2G5CA

820.0 C192C821(4)2G5CA
1,000.0 C192C102(4)2G5CA
1,200.0 C192C122(4)2G5CA
1,500.0 C192C152(4)2G5CA
1,800.0 C192C182(4)2G5CA
2,200.0 C192C222(4

)2G5CA
2,700.0 C192C272(4)2G5CA
3,300.0 C192C332(4)2G5CA
3,900.0 C192C392(4

)2G5CA
4,700.0 C192C472(4)2G5CA

100 VOLT — C192 STANDARD C0G

1,200.0 C192C122(4

)1G5CA
1,500.0 C192C152(4)1G5CA
1,800.0 C192C182(4

)1G5CA
2,200.0 C192C222(4

)1G5CA
2,700.0 C192C272(4)1G5CA
3,300.0 C192C332(4

)1G5CA
3,900.0 C192C392(4)1G5CA
4,700.0 C192C472(4

)1G5CA
5,600.0 C192C562(4

)1G5CA
6,800.0 C192C682(4)1G5CA
8,200.0 C192C822(4)1G5CA

RATINGS & PART NUMBER REFERENCE

CAPACITANCE KEMET

pF PART NUMBER

200 VOLT — C114 STANDARD C0G

1.0 C114C109(1)2G5CA

1.5 C114C159(1)2G5CA

2.2 C114C229(1)2G5CA

2.7 C114C279(1

)2G5CA

3.3 C114C339(1)2G5CA

3.9 C114C399(1)2G5CA

4.7 C114C479(1)2G5CA

5.6 C114C569(1)2G5CA

6.8 C114C689(1)2G5CA

8.2 C114C829(1)2G5CA

10.0 C114C100(2)2G5CA

12.0 C114C120(2)2G5CA

15.0 C114C150(2)2G5CA

18.0 C114C180(2)2G5CA

22.0 C114C220(2)2G5CA

27.0 C114C270(3

)2G5CA

33.0 C114C330(3)2G5CA

39.0 C114C390(3)2G5CA

47.0 C114C470(3)2G5CA

56.0 C114C560(4)2G5CA

68.0 C114C680(4)2G5CA

82.0 C114C820(4)2G5CA

100.0 C114C101(4)2G5CA

120.0 C114C121(4)2G5CA

150.0 C114C151(4)2G5CA

180.0 C114C181(4)2G5CA

220.0 C114C221(4)2G5CA

270.0 C114C271(4)2G5CA

330.0 C114C331(4)2G5CA

100 VOLT — C114 STANDARD C0G

82.0 C114C820(4

)1G5CA

100.0 C114C101(4)1G5CA

120.0 C114C121(4

)1G5CA

150.0 C114C151(4)1G5CA

180.0 C114C181(4

)1G5CA

220.0 C114C221(4)1G5CA

270.0 C114C271(4

)1G5CA

330.0 C114C331(4

)1G5CA

390.0 C114C391(4)1G5CA

470.0 C114C471(4

)1G5CA

560.0 C114C561(4)1G5CA

680.0 C114C681(4

)1G5CA

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(1) 1.0 pF to 8.2 pF: D— ±.5 pF
(2) 10.0 pF to 22 pF: J— ±5%, K— ±10%
(3) 27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%
(4) 56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(1) 1.0 pF to 8.2 pF: D— ±.5 pF
(2) 10.0 pF to 22 pF: J— ±5%, K— ±10%
(3) 27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%
(4) 56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(1) 1.0 pF to 8.2 pF: D— ±.5 pF
(2) 10.0 pF to 22 pF: J— ±5%, K— ±10%
(3) 27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%
(4) 56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%

© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, [phone]

CERAMIC MOLDED/RADIAL – STANDARD

ULTRA-STABLE TEMPERATURE CHARACTERISTIC—C0G (NP0)

24

RATINGS & PART NUMBER REFERENCE

CAPACITANCE KEMET

pF PART NUMBER

200 VOLT — C062 SIZE C0G

3,300.0 C062C332(4)2G5CA
3,900.0 C062C392(4)2G5CA
4,700.0 C062C472(4)2G5CA
5,600.0 C062C562(4)2G5CA
6,800.0 C062C682(4

)2G5CA

8,200.0 C062C822(4)2G5CA

10,000.0 C062C103(4)2G5CA

100 VOLT — C062 SIZE C0G

5,600.0 C062C562(4

)1G5CA
6,800.0 C062C682(4)1G5CA
8,200.0 C062C822(4)1G5CA

10,000.0 C062C103(4)1G5CA
12,000.0 C062C123(4)1G5CA
15,000.0 C062C153(4)1G5CA
18,000.0 C062C183(4)1G5CA
22,000.0 C062C223(4

)1G5CA

200 VOLT — C512 SIZE C0G

12,000.0 C512C123(4

)2G5CA

15,000.0 C512C153(4)2G5CA
18,000.0 C512C183(4)2G5CA
22,000.0 C512C223(4)2G5CA
27,000.0 C512C273(4)2G5CA
33,000.0 C512C333(4)2G5CA
39,000.0 C512C393(4)2G5CA
47,000.0 C512C473(4)2G5CA
56,000.0 C512C563(4)2G5CA
68,000.0 C512C683(4)2G5CA

100 VOLT — C512 SIZE C0G

27,000.0 C512C273(4

)1G5CA

33,000.0 C512C333(4)1G5CA
39,000.0 C512C393(4)1G5CA
47,000.0 C512C473(4)1G5CA
56,000.0 C512C563(4)1G5CA
68,000.0 C512C683(4)1G5CA
82,000.0 C512C823(4)1G5CA

100,000.0 C512C104(4)1G5CA

200 VOLT — C522 SIZE C0G

82,000.0 C522C823(4

)2G5CA

100,000.0 C522C104(4)2G5CA

100 VOLT — C522 SIZE C0G

120,000.0 C522C124(4

)1G5CA

150,000.0 C522C154(4)1G5CA
180,000.0 C522C184(4)1G5CA

CAPACITANCE KEMET

pF PART NUMBER

200 VOLT — C052 SIZE C0G

1.0 C052C109(1

)2G5CA

1.5 C052C159(1)2G5CA

2.2 C052C229(1

)2G5CA

2.7 C052C279(1)2G5CA

3.3 C052C339(1

)2G5CA

3.9 C052C399(1)2G5CA

4.7 C052C479(1)2G5CA

5.6 C052C569(1)2G5CA

6.8 C052C689(1)2G5CA

8.2 C052C829(1)2G5CA

10.0 C052C100(2)2G5CA

12.0 C052C120(2)2G5CA

15.0 C052C150(2)2G5CA

18.0 C052C180(2)2G5CA

22.0 C052C220(2)2G5CA

27.0 C052C270(3)2G5CA

33.0 C052C330(3)2G5CA

39.0 C052C390(3)2G5CA

47.0 C052C470(3)2G5CA

56.0 C052C560(4)2G5CA

68.0 C052C680(4)2G5CA

82.0 C052C820(4)2G5CA

100.0 C052C101(4)2G5CA

120.0 C052C121(4)2G5CA

150.0 C052C151(4)2G5CA

180.0 C052C181(4)2G5CA

220.0 C052C221(4

)2G5CA

270.0 C052C271(4)2G5CA

330.0 C052C331(4)2G5CA

390.0 C052C391(4)2G5CA

470.0 C052C471(4)2G5CA

560.0 C052C561(4)2G5CA

680.0 C052C681(4)2G5CA

820.0 C052C821(4)2G5CA
1,000.0 C052C102(4)2G5CA
1,200.0 C052C122(4)2G5CA
1,500.0 C052C152(4)2G5CA
1,800.0 C052C182(4)2G5CA
2,200.0 C052C222(4)2G5CA
2,700.0 C052C272(4)2G5CA

100 VOLT — C052 SIZE C0G

390.0 C052C391(4

)1G5CA

470.0 C052C471(4)1G5CA

560.0 C052C561(4)1G5CA

680.0 C052C681(4

)1G5CA

820.0 C052C821(4)1G5CA
1,000.0 C052C102(4)1G5CA
1,200.0 C052C122(4)1G5CA
1,500.0 C052C152(4)1G5CA
1,800.0 C052C182(4)1G5CA
2,200.0 C052C222(4)1G5CA
2,700.0 C052C272(4)1G5CA
3,300.0 C052C332(4)1G5CA
3,900.0 C052C392(4)1G5CA
4,700.0 C052C472(4)1G5CA

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(1) 1.0 pF to 8.2 pF: D— ±.5 pF
(2) 10.0 pF to 22 pF: J— ±5%, K— ±10%
(3) 27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%
(4) 56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%

NOTE 1: Insert proper symbol for capacitance tolerance as

follows:

(1) 1.0 pF to 8.2 pF: D— ±.5 pF
(2) 10.0 pF to 22 pF: J— ±5%, K— ±10%
(3) 27.0 pF to 47 pF: G— ±2%, J— ±5%, K— ±10%
(4) 56.0 pF and up: F— ±1%,G— ±2%, J— ±5%, K— ±10%

© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, [phone] 25

Ceramic Molded

Axial/Radial - Standard

CERAMIC MOLDED/AXIAL – STANDARD

STABLE TEMPERATURE CHARACTERISTIC—X7R

TOL. KEMET

% PART NUMBER

100 VOLT — C202 SIZE

56,000 10 C202C563K1R5CA
68,000 10 C202C683K1R5CA
68,000 20 C202C683M1R5CA

82,000 10 C202C823K1R5CA
100,000 10 C202C104K1R5CA
100,000 20 C202C104M1R5CA
120,000 10 C202C124K1R5CA
150,000 10 C202C154K1R5CA
150,000 20 C202C154M1R5CA
180,000 10 C202C184K1R5CA
220,000 10 C202C224K1R5CA
220,000 20 C202C224M1R5CA
270,000 10 C202C274K1R5CA
330,000 10 C202C334K1R5CA
330,000 20 C202C334M1R5CA

50 VOLT — C202 SIZE

470,000 10 C202C474K5R5CA
470,000 20 C202C474M5R5CA
680,000 10 C202C684K5R5CA
680,000 20 C202C684M5R5CA

1,000,000 10 C202C105K5R5CA
1,000,000 20 C202C105M5R5CA

100 VOLT — C222 SIZE

470,000 10 C222C474K1R5CA
470,000 20 C222C474M1R5CA
680,000 10 C222C684K1R5CA
680,000 20 C222C684M1R5CA

1,000,000 10 C222C105K1R5CA
1,000,000 20 C222C105M1R5CA

50 VOLT — C222 SIZE

2,200,000 10 C222C225K5R5CA
2,200,000 20 C222C225M5R5CA
3,300,000 10 C222C335K5R5CA
3,300,000 20 C222C335M5R5CA

CAPACI–

TANCE

pF

TOL. KEMET

% PART NUMBER

100 VOLT — C124 SIZE

5,600 10 C124C562K1R5CA
6,800 10 C124C682K1R5CA
6,800 20 C124C682M1R5CA

8,200 10 C124C822K1R5CA
10,000 10 C124C103K1R5CA
10,000 20 C124C103M1R5CA

50 VOLT — C124 SIZE

12,000 10 C124C123K5R5CA
15,000 10 C124C153K5R5CA
15,000 20 C124C153M5R5CA
18,000 10 C124C183K5R5CA
22,000 10 C124C223K5R5CA
22,000 20 C124C223M5R5CA
27,000 10 C124C273K5R5CA
33,000 10 C124C333K5R5CA
33,000 20 C124C333M5R5CA
39,000 10 C124C393K5R5CA
47,000 10 C124C473K5R5CA
47,000 20 C124C473M5R5CA

100 VOLT — C192 SIZE

12,000 10 C192C123K1R5CA
15,000 10 C192C153K1R5CA
15,000 20 C192C153M1R5CA
18,000 10 C192C183K1R5CA
22,000 10 C192C223K1R5CA
22,000 20 C192C223M1R5CA
27,000 10 C192C273K1R5CA
33,000 10 C192C333K1R5CA
33,000 20 C192C333M1R5CA
39,000 10 C192C393K1R5CA
47,000 10 C192C473K1R5CA
47,000 20 C192C473M1R5CA
56,000 10 C192C563K1R5CA
68,000 10 C192C683K1R5CA
68,000 20 C192C683M1R5CA
82,000 10 C192C823K1R5CA

100,000 10 C192C104K1R5CA
100,000 20 C192C104M1R5CA

50 VOLT — C192 SIZE

56,000 10 C192C563K5R5CA
68,000 10 C192C683K5R5CA
68,000 20 C192C683M5R5CA
82,000 10 C192C823K5R5CA

100,000 10 C192C104K5R5CA
100,000 20 C192C104M5R5CA
120,000 10 C192C124K5R5CA
150,000 10 C192C154K5R5CA
150,000 20 C192C154M5R5CA
180,000 10 C192C184K5R5CA
220,000 10 C192C224K5R5CA
220,000 20 C192C224M5R5CA
270,000 10 C192C274K5R5CA

RATINGS & PART NUMBER REFERENCE

TOL. KEMET

% PART NUMBER

100 VOLT — C114 SIZE

10 10 C114C100K1R5CA
10 20 C114C100M1R5CA
12 10 C114C120K1R5CA
15 10 C114C150K1R5CA
15 20 C114C150M1R5CA
18 10 C114C180K1R5CA
22 20 C114C220K1R5CA
22 10 C114C220M1R5CA
27 10 C114C270K1R5CA
33 10 C114C330K1R5CA
33 20 C114C330M1R5CA
39 10 C114C390K1R5CA
47 10 C114C470K1R5CA
47 20 C114C470M1R5CA
56 10 C114C560K1R5CA
68 10 C114C680K1R5CA
68 20 C114C680M1R5CA

82 10 C114C820K1R5CA
100 10 C114C101K1R5CA
100 20 C114C101M1R5CA
120 10 C114C121K1R5CA
150 10 C114C151K1R5CA
150 20 C114C151M1R5CA
180 10 C114C181K1R5CA
220 10 C114C221K1R5CA
220 20 C114C221M1R5CA
270 10 C114C271K1R5CA
330 10 C114C331K1R5CA
330 20 C114C331M1R5CA
390 10 C114C391K1R5CA
470 10 C114C471K1R5CA
470 20 C114C471M1R5CA
560 10 C114C561K1R5CA
680 10 C114C681K1R5CA
680 20 C114C681M1R5CA
820 10 C114C821K1R5CA

1,000 10 C114C102K1R5CA
1,000 20 C114C102M1R5CA
1,200 10 C114C122K1R5CA
1,500 10 C114C152K1R5CA
1,500 20 C114C152M1R5CA
1,800 10 C114C182K1R5CA
2,200 10 C114C222K1R5CA
2,200 20 C114C222M1R5CA
2,700 10 C114C272K1R5CA
3,300 10 C114C332K1R5CA
3,300 20 C114C332M1R5CA
3,900 10 C114C392K1R5CA
4,700 10 C114C472K1R5CA
4,700 20 C114C472M1R5CA

50 VOLT — C114 SIZE

5,600 10 C114C562K5R5CA
6,800 10 C114C682K5R5CA
6,800 20 C114C682M5R5CA

8,200 10 C114C822K5R5CA
10,000 10 C114C103K5R5CA
10,000 20 C114C103M5R5CA

CAPACI–

TANCE

pF

CAPACI–

TANCE

pF

© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, [phone]26

CERAMIC MOLDED/RADIAL – STANDARD

STABLE TEMPERATURE CHARACTERISTIC—X7R

TOL. KEMET

% PART NUMBER

100 VOLT — C062 SIZE

12,000 10 C062C123K1R5CA
15,000 10 C062C153K1R5CA
15,000 20 C062C153M1R5CA
18,000 10 C062C183K1R5CA
22,000 10 C062C223K1R5CA
22,000 20 C062C223M1R5CA
27,000 10 C062C273K1R5CA
33,000 10 C062C333K1R5CA
33,000 20 C062C333M1R5CA
39,000 10 C062C393K1R5CA
47,000 10 C062C473K1R5CA
47,000 20 C062C473M1R5CA
56,000 10 C062C563K1R5CA
68,000 10 C062C683K1R5CA
68,000 20 C062C683M1R5CA

82,000 10 C062C823K1R5CA
100,000 10 C062C104K1R5CA
100,000 20 C062C104M1R5CA

50 VOLT — C062 SIZE

120,000 10 C062C124K5R5CA
150,000 10 C062C154K5R5CA
150,000 20 C062C154M5R5CA
180,000 10 C062C184K5R5CA
220,000 10 C062C224K5R5CA
220,000 20 C062C224M5R5CA
270,000 10 C062C274K5R5CA
330,000 10 C062C334K5R5CA
330,000 20 C062C334M5R5CA
390,000 10 C062C394K5R5CA
470,000 10 C062C474K5R5CA
470,000 20 C062C474M5R5CA
560,000 10 C062C564K5R5CA
680,000 10 C062C684K5R5CA
680,000 20 C062C684M5R5CA
820,000 10 C062C824K5R5CA

1,000,000 10 C062C105K5R5CA
1,000,000 20 C062C105M5R5CA

50 VOLT — C512 SIZE

1,000,000 10 C512C105K5X5CA
1,000,000 20 C512C105M5X5CA

1,500,000 10 C512C155K5X5CA
1,500,000 20 C512C155M5X5CA

2,000,000 10 C512C205K5X5CA
2,000,000 20 C512C205M5X5CA

2,200,000 10 C512C225K5X5CA
2,200,000 20 C512C225M5X5CA

100 VOLT — C522 SIZE

1,000,000 10 C522C105K1X5CA
1,000,000 20 C522C105M1X5CA

50 VOLT — C522 SIZE

2,700,000 10 C522C275K5X5CA
2,700,000 20 C522C275M5X5CA

3,300,000 10 C522C335K5X5CA
3,300,000 20 C522C335M5X5CA

CAPACI–

TANCE

pF

TOL. KEMET

% PART NUMBER

100 VOLT — C052 SIZE

1,200 10 C052C122K1R5CA
1,500 10 C052C152K1R5CA
1,500 20 C052C152M1R5CA
1,800 10 C052C182K1R5CA
2,200 10 C052C222K1R5CA
2,200 20 C052C222M1R5CA
2,700 10 C052C272K1R5CA
3,300 10 C052C332K1R5CA
3,300 20 C052C332M1R5CA
3,900 10 C052C392K1R5CA
4,700 10 C052C472K1R5CA
4,700 20 C052C472M1R5CA
5,600 10 C052C562K1R5CA
6,800 10 C052C682K1R5CA
6,800 20 C052C682M1R5CA

8,200 10 C052C822K1R5CA
10,000 10 C052C103K1R5CA
10,000 20 C052C103M1R5CA

50 VOLT — C052 SIZE

12,000 10 C052C123K5R5CA
15,000 10 C052C153K5R5CA
15,000 20 C052C153M5R5CA
18,000 10 C052C183K5R5CA
22,000 10 C052C223K5R5CA
22,000 20 C052C223M5R5CA
27,000 10 C052C273K5R5CA
33,000 10 C052C333K5R5CA
33,000 20 C052C333M5R5CA
39,000 10 C052C393K5R5CA
47,000 10 C052C473K5R5CA
47,000 20 C052C473M5R5CA
56,000 10 C052C563K5R5CA
68,000 10 C052C683K5R5CA
68,000 20 C052C683M5R5CA
82,000 10 C052C823K5R5CA

100,000 10 C052C104K5R5CA
100,000 20 C052C104M5R5CA

200 VOLT — C062 SIZE

1,200 10 C062C122K2R5CA

1,500 10 C062C152K2R5CA

1,500 20 C062C152M2R5CA

1,800 10 C062C182K2R5CA

2,200 10 C062C222K2R5CA

2,200 20 C062C222M2R5CA

2,700 10 C062C272K2R5CA

3,300 10 C062C332K2R5CA

3,300 20 C062C332M2R5CA

3,900 10 C062C392K2R5CA

4,700 10 C062C472K2R5CA

4,700 20 C062C472M2R5CA

5,600 10 C062C562K2R5CA

6,800 10 C062C682K2R5CA

6,800 20 C062C682M2R5CA

8,200 10 C062C822K2R5CA
10,000 10 C062C103K2R5CA
10,000 20 C062C103M2R5CA

RATINGS & PART NUMBER REFERENCE

TOL. KEMET

% PART NUMBER

200 VOLT — C052 SIZE

10 10 C052C100K2R5CA
10 20 C052C100M2R5CA
12 10 C052C120K2R5CA
15 10 C052C150K2R5CA
15 20 C052C150M2R5CA
18 10 C052C180K2R5CA
22 10 C052C220K2R5CA
22 20 C052C220M2R5CA
27 10 C052C270K2R5CA
33 10 C052C330K2R5CA
33 20 C052C330M2R5CA
39 10 C052C390K2R5CA
47 10 C052C470K2R5CA
47 20 C052C470M2R5CA
56 10 C052C560K2R5CA
68 10 C052C680K2R5CA
68 20 C052C680M2R5CA

82 10 C052C820K2R5CA
100 10 C052C101K2R5CA
100 20 C052C101M2R5CA
120 10 C052C121K2R5CA
150 10 C052C151K2R5CA
150 20 C052C151M2R5CA
180 10 C052C181K2R5CA
220 10 C052C221K2R5CA
220 20 C052C221M2R5CA
270 10 C052C271K2R5CA
330 10 C052C331K2R5CA
330 20 C052C331M2R5CA
390 10 C052C391K2R5CA
470 10 C052C471K2R5CA
470 20 C052C471M2R5CA
560 10 C052C561K2R5CA
680 10 C052C681K2R5CA
680 20 C052C681M2R5CA
820 10 C052C821K2R5CA

1,000 10 C052C102K2R5CA
1,000 20 C052C102M2R5CA

CAPACI–

TANCE

pF

CAPACI–

TANCE

pF

© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, [phone] 39

CERAMIC LEADED

PACKAGING INFORMATION

Tape and Reel Packaging

Ceramic Axial

Lead Tape and Reel Packaging

KEMET offers standard reeling of Molded and Conformally
Coated Axial Leaded Ceramic Capacitors for automatic insertion
or lead forming machines per EIA specification RS-296. KEMET’S
internal specification four-digit suffix, 7200, is placed at the end of
the part number to designate tape and reel packaging, ie:
C410C104Z5U5CA7200.

Paper (50 lb.) test minimum is inserted between the layers of
capacitors wound on reels for component pitch ≤ 0.400".
Capacitor lead length may extend only a maximum of .0625"
(1.59mm) beyond the tapes' edges. Capacitors are centered in a
row between the two tapes and will deviate only ± 0.031
(0.79mm) from the row center. A minimum of 36" (91.5 cm) leader
tape is provided at each end of the reel capacitors. Universal
splicing clips are used to connect the tape. Standard reel
quantities are shown on page 41.

Adhesive Tape

Figure 1

®

KEMET

®

KEMET

Table 1

Figure 2

10.5" - 14"
(26.67 -

35.56cm)

.655" ±0.010"

(16.6 ±0.25)

Dimensions in Inches & (Millimeters)

Component

Body Diameter

Adhesive Tape

.059" to .315"

*

31/4"

(82.6)

Component

Pitch "A"

0.020" or (±0.5mm) I III*

Greater Than

Component

Length

Hub

1

/8"

(3.18)

Inside Tape Spacing "B"

± 1.5mm (0.059")

Kraft Paper

Interleaving

Figure 3

See Table 1

(B)

.047" Max

(1.20)

See Table 1 (A)

*

.250" Nom.

(6.35)

0" (0mm) to 0.197" (5mm)

0.197" (5.01mm) to 0.394: (10mm)

* Not Available for Conformally Coated Parts.

0.197" or (5mm)

0.394" or (10mm)

2.062" (52.4mm)

2.874" (73mm)

CERAMIC LEADED

PACKAGING INFORMATION

© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, [phone]40

Ceramic Radial

Lead Tape and Reel Packaging

KEMET offers standard reeling of Molded and Conformally
Coated Radial Leaded Ceramic Capacitors for automatic
insertion per EIA specification RS-468. Parts are taped to a
tagboard carrier strip, and wound on a reel as shown in
Figure 1. Kraft paper interleaving is inserted between the
layers of capacitors on the reel. Ammopack is also available,
with the same lead tape configuration and package quantities.

Figure 1

Carrier Strip

®

KEMET

12"

(30.48 cm

.655" ±0.010"

0.25)

(16.6 ±

)

*

(82.6)

31/4"

.059" to .315"
Greater Than

Over All

Height

of T aped

Component

Hub

1

/8"

(3.18)

s

Figure 3: Standard Reel

H1

C315*
C320*

D

0

C340**

C6xx#

C056**
C066**

H

F

C330**

CK06**

CKR06**

C062**

Figure 2: Lead Tape Configuration (See Table Below)

Ceramic Radial Tape and Reel Dimensions in Millimeters & (Inches)

Dimension Symbol

Sprocket Hole Diameter
Sprocket Hole Pitch
Component Pitch
Lead Spacing (1)
Sprocket Hole Center

to Lead Center (1)
Sprocket Hole Center
to Component Center
Height to Seating Plane
(straight leads) (2)
Component Height
Above T ape Center

(1) Measured at the egress from the carrier tape, on the component side.
(2) Determined by a 4 digit suffix placed at the end of the part number, as follows:
7301 =
7303 =

Recommended for parts with formed leads.
Recommended for parts with straight leads.

Do
P0

P

F
P1
P2

H
H1

Nominal
mm (inch)

4.0 (.157)

12.7 (.500)

12.7 (.500)

5.08 2.54
(.20) (.10)

3.81 5.08

(.150) (.200)

6.35 (.250)

7301 7303

16.0 (.630) 18.0 (.709)

32.2 (1.27)

Tolerance
mm (inch) Dimension Symbol

± 0.2 (.008)
± 0.3 (.012)
± 0.3 (.012)

+0.6 -0.2

(+.024 -.008)

± 0.7 (.028)
± 1.3 (.051)

7301 7303

±0.5 (.020) Minimum

Maximum

Example: C322C104K5R5CA7301
Example: C320C104K5R5CA7303

Adhesive T

CK05**

CKR05**

C052**

P

P1

T

Height to Seating
Plane (formed leads) (2)

Component Alignment
Lead Protrusion
Composite T ape

Thickness
Overall T ape and
Lead Thickness
Carrier T ape Width

Hold-Down T ape
Width
Hold-Down T ape
Location

ape

C317**
C322**
C323**

P

2

H

Carrier Tape

0

C6xx#

C333**

L

1

P

0

H

7301 7303

0

16.0 (.630) 18.0 (.709)

∆h
L1
t
T
W
W0
W2

KEMET

Kraft Paper

Interleaving

(Note: Non-standard lead lengths

available in bulk only.)

∆H

1MM Max.
(.039")

W

2

W

W

0

W

2

* Lead spacings are 2.54mm
(.10") center-to-center.
** Lead spacings are 5.08mm
(.20") center-to-center.
# See page 15 for exact lead

configuration for Series.

Nominal
mm (inch)

4.0 (.157)

1.0 (.039)

0.7 (.051)

1.5 (.059)

18.0 (.709)

5.0 (.197)

3.0 (.118)

7301 7303

±0.5 (.020) Minimum

(+.039 -.020)

Tape

Carrier

Tolerance
mm (inch)

±0.2 (.008)

Maximum

±0.2 (.008)

Maximum
+1.0 - 0.5

Minimum

Maximum

®

CERAMIC PACKAGING

CERAMIC LEADED

PACKAGING INFORMATION

KEMET

Series

C114C-K-G CK12, CC75 MIL-C-11015/ 200/Box 5000 12"
C124C-K-G CK13, CC76 MIL-PRF-20 200/Box 5000 12"
C192C-K-G CK14, CC77 100/Box 3000 12"
C202C-K CK15 25/Box 500 12"
C222C-K CK16 10/Tray 300 12"
C052C-K-G CK05, CC05 100/Bag 2000 2000 12"
C062C-K-G CK06, CC06 100/Bag 1500 1500 12"
C114G CCR75 MIL-PRF-20 200/Box 5000 12"
C124G CCR76 200/Box 5000 12"
C192G CCR77 100/Box 3000 12"
C202G CC78-CCR78 25/Box 500 12"
C222G CC79-CCR79 10/Tray 300 12"
C052/56G CCR05 100/Bag 1700 12"
C062/66G CCR06 100/Bag 1500 12"
C512G CC07-CCR07 Footnote (2) N/A N/A
C522G CC08-CCR08 Footnote (2) N/A N/A
C114T CKR11 MIL-PRF-39014 200/Box 5000 12"
C124T CKR12 200/Box 5000 12"
C192T CKR14 100/Box 3000 12"
C202T CKR15 25/Box 500 12"
C222T CKR16 10/Tray 300 12"
C052/56T CKR05 100/Bag 1700 12"
C062/66T CKR06 100/Bag 1500 12"
C31X 500/Bag 2500 2500 12"
C32X 500/Bag 2500 2500 12"
C33X 250/Bag 1500 1500 12"
C340 100/Bag 1000 1000 12"
C350 50/Bag N/A N/A N/A
C410 300/Box 4000 5000 12"
C412 200/Box 4000 5000 12"
C420 300/Box 4000 5000 12"
C430 200/Box 2000 2500 12"
C440 200/Box 2000 2500
C512 N/A N/A Footnote (2) N/A
C522 N/A N/A Footnote (2) N/A
C617 500/Bag
C622/C623 500/Bag
C627/C628 500/Bag
C630/C631 250/Bag
C637/C638 250/Bag
C640/C641 100/Bag
C642/C643 100/Bag
C647/C648 100/Bag
C657/C658 50/Bag
C667/C668 50/Bag

NOTE: (1) Standard packaging refers to number of pieces per bag, tray or vial.
(2) Quantity varies. For further details, please consult the factory.

Military

Style

Military

Specification

Standard (1)

Bulk

Quantity

Ammo Pack

Quantity

Maximum

Maximum

Reel

Quantity

Reel
Size

12"
N/A
N/A

Tape and Reel Packaging

© KEMET Electronics Corporation, P.O. Box 5928, Greenville, S.C. 29606, [phone] 41