Datasheet BWD512, BWD4815, BWD4812, BWD4805, BWD2415 Datasheet (Power-one)

...
Page 1
(888) IPD-CONVerters
(888) 473-2668www.ipdconverters.com
BWD SERIES - DUAL OUTPUT, 2.5 WATT
DESCRIPTION FEATURES
BWD dual output DC/DC converters offer excellent regulation and isolation in an industry standard DIP package. With several input voltage ranges, the BWD is perfect for industrial, telecom, and networking applications. The BWD features short circuit protection, low profile, and 500 VDC isolation. Please see the BWS series for single output applications.
TECHNICAL SPECIFICA TIONS
Input
Voltage Range
5 VDC Nominal 4.5 - 9 VDC 12 VDC Nominal 9 - 18 VDC 24 VDC Nominal 19 - 36 VDC 48 VDC Nominal 36 - 72 VDC
Reflected Ripple 20% Iin Max. Reverse Input Current 100% Iin Max.
Output
Setpoint Accuracy ±1% Line Regulation Vin Min. - Vin Max., I Load Regulation I
Min. - I
out
out
Minimum Output Current 10 % l Dynamic Regulation, 1/4 to Full Load Step 25% I
Pk Deviation 4% V
Settling Time 500 µs Temperature Coefficient 0.02%/°C Ripple and Noise, 20 MHz BW 150 mV Short Circuit Protection
1
Current Limit 180%
No Load Input Power 0.7 W Switching Frequency 200 kHz Isolation
Input - Output 500 VDC Input - Case 500 VDC
Output - Case 500 VDC Isolation Resistance - Input to Output 109 Ohms Isolation Capacitance - Input to Output 80 pF Case Temperature
Standard Operating Range -25 to +85°C
Storage Range -40 to +125°C Humidity Max., Non-Condensing 95% Vibration, 3 Axes, 5 Min Each 5 g, 10 - 55 Hz Safety UL, CUL, TUV Weight (Approx.) 0.7 oz
Rated ±1.5% V
out
Max., Vin Nom. ±2.5% V
Rated
out
Continuous Auto-restart
General
out out
out out
• Industry Standard Dip Package
• Industry Standard Pinout
• 85°C Case Operation
Efficiency vs. Load (24V Input)
85 80 75 70 65 60 55
EFFICIENCY %
50 45 40
10 20 30 40 50 60 70 80 90 100
Efficiency vs. Load (48V Input)
90 85 80 75 70 65 60
55 50 45 40
10 20 30 40 50 60 70 80 90 100
1
Continuous short circuit protection is provided. Long-term continuous operation in this mode is not recommended. Converter will auto-restart once fault has been removed
Specifications typically at 25°C, normal line, and full load, unless otherwise stated.
Soldering Conditions: I/O pins, 260°C, ten seconds; fully compatible with commercial wave-soldering equipment.
Safety: Agency approvals may vary from model to model. Please consult factory for specific model information.
• Wide Range Input
• Input Pi Filter
• 500V Isolation
• Short Circuit Protection
EFF. BWD2415
EFF. BWD2412
LOAD %
EFF. BWD4812 EFF. BWD4808
LOAD %
Notes
1
Page 2
BWD SERIES - DUAL OUTPUT, 2.5 WATT
MODELS - (See the last page of this file for options.)
Vin
(Volts)
5
5 12 12 12 24 24 24 48 48 48
Vin Range
(Volts)
4.5 - 9. 0
4.5 - 9. 0
9.0 - 18.0
9.0 - 18.0
9.0 - 18.0
18.0 - 36.0
18.0 - 36.0
18.0 - 36.0
36.0 - 72.0
36.0 - 72.0
36.0 - 72.0
Iin Max.*
(Amps)
0.92
0.93
0.42
0.46
0.46
0.20
0.23
0.23
0.10
0.11
0.11
* Maximum input current at minimum input voltage, maximum rated output power. ** At nominal Vin, rated output.
MECHANICAL DRAWING
0.80"
(20.3mm)
0.900"(22.9mm)
0.800"(20.3mm)
23 22
2 3
Vout
(Volts)
±12 ±15
±5 ±12 ±15
±5 ±12 ±15
±5 ±12 ±15
Iout Rated
(Amps)
±.0.125 ±.0.100
±0.250 ±0.125 ±0.100 ±0.250 ±0.125 ±0.100 ±0.250 ±0.125 ±0.100
Rip p le & No ise
Pk-Pk (mV)
150 150 150 150 150 150 150 150 150 150 150
0.18"(4.6mm)
Efficiency
Typ. **
79% 73% 73% 79% 79% 75% 79% 78% 76% 79% 79%
Model
BWD512 BWD0515 BWD1205 BWD1212 BWD1215 BWD2405 BWD2412 BWD2415 BWD4805 BWD4812 BWD4815
0.200"(5.1mm)
0.100"(2.5mm)
0.175"( 4.5mm)
Thermal Impedance
Natural Convection 2.5 °C/W 100 LFM 2.1 °C/W 200 LFM 1.7 °C/W 300 LFM 1.3 °C/W
Note: Thermal impedance data is dependent on many environmental factors. The exact thermal performance should be validated for specific application.
0
0.10"
( 2.5mm)
BOTTOM VIEW
16 15 14
0
(15.2mm)
1.25"
(31.8mm)
9 10 11
0.600"
Pin Function
1 & 24 No Pin 2 & 23 - Vin / +V 3 & 22 - Vin / +V 4 & 21 No Pin
5 & 20 No Pin 6 & 19 No Pin 7 & 18 No Pin 8 & 17 No Pin 9 & 16 Common 10 & 15 No Conn.
11 & 14 -V 12 & 13 No Pin
out
/ + V
2
DIA 0.020"
(0.5mm)
in in
out
0.52"
(13.2mm)
Tolerances
Inches: (Millimeters) .XX ± 0.040 .X ± 1.0 .XXX ± 0.010 .XX ± 0.25
Pin: ± 0.002 ± 0.05
(Tolerances as listed unless otherwise specified.)
Page 3
OPTIONS
When ordering equipment options, use the following suffix information. Select the option(s) that you prefer and add them to the model number. Example ordering options are located below the options table.
OPTION SUFFIX APPLICABLE SERIES REMARKS
Negative Logic N HAS, HBD, HBS, HES, LES, QBS,
Lucent Compatible Trim T HAS, HBD, HBS, HES, QBS, QES Terminal Strip TS XWS, XWD, XWT Trim 1 IAS, LES Enable 2 IAD, IAS, LES, SMS Trim and Enable 3 IAS, LES Current Share 4 SMS Headerless Y Encapsulated EWS, IWS, OWS
PIN LENGTH AND HEATSINK OPTIONS
0.110” (2.8mm) Pin Length 8 All Units (Except SMS)
0.150” (3.8mm) Pin Length 9 All Units (Except SMS)
0.24” (6.1mm) Horizontal Heatsink 1H All Units (Except DIP, SIP, and SM
0.24” (6.1mm) Vertical Heatsink 1V All Units (Except DIP, SIP, and SM
0.45” (11.4mm) Horizontal Heatsink
0.45” (11.4mm) Vertical Heatsink 2V All Units (Except DIP, SIP, and SM
0.95” (24.1mm) Horizontal Heatsink
0.95” (24.1mm) Vertical Heatsink 3V All Units (Except DIP, SIP, and SM
2H All Units (Except DIP, SIP, and SM
3H All Units (Except DIP, SIP, and SM
QES, TES, TQD
Packages)
Packages)
Packages)
Packages)
Packages)
Packages)
TTL “Low” Turns Module ON TTL “High” Turns Module OFF
Standard Pin Length is 0.180” (4.6mm)
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Includes Thermal Pad
Example Options:HBS050ZG-ANT3V = HBS050ZG-A with negative logic, Lucent compatible trim, and
0.95” vertical heatsink. LES015YJ-3N = LES015YJ with optional trim and enable, negative logic. QBS066ZG-AT8 = QBS066ZG-A with Lucent compatible trim and 0.110” pin length.
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems,
equipment used in hazardous environments, or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the
date manufactured. Specifications are subject to change without notice.
3
Loading...