Datasheet BTA212B-800F, BTA212B-800E, BTA212B-600F, BTA212B-600E, BTA212B-600D Datasheet (Philips)

Philips Semiconductors Objective specification

Three quadrant triacs BTA212B series D, E and F
guaranteed commutation

GENERAL DESCRIPTION QUICK REFERENCE DATA

Passivated guaranteed commutation SYMBOL PARAMETER MAX. MAX. UNIT
triacs in a plastic envelope suitable for
surface mounting intended for use in BTA212B- 600D -
motorcontrol circuits or withother highly BTA212B- 600E 800E
inductive loads. These devices balance BTA212B- 600F 800F
the requirements of commutation V
performance and gate sensitivity. The voltages
"sensitivegate"Eseriesand"logiclevel" I
Dseries are intended forinterfacingwith I
low power drivers, including micro current

DRM

T(RMS)
TSM

controllers.

PINNING - SOT404 PIN CONFIGURATION SYMBOL

Repetitive peak off-state 600 800 V
RMS on-state current 12 12 A

Non-repetitive peak on-state 95 95 A

PIN DESCRIPTION

mb

1 main terminal 1
2 main terminal 2
3 gate

mb main terminal 2

2

13

LIMITING VALUES

Limiting values in accordance with the Absolute Maximum System (IEC 134).

SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT

-600 -800

V

DRM

I

T(RMS)

Repetitive peak off-state - 600
voltages

RMS on-state current full sine wave; - 12 A

Tmb ≤ 99 ˚C

I

TSM

Non-repetitive peak full sine wave;
on-state current Tj = 25 ˚C prior to

surge
t = 20 ms - 95 A

I2tI

2

t for fusing t = 10 ms - 45 A2s

t = 16.7 ms - 105 A

dIT/dt Repetitive rate of rise of ITM = 20 A; IG = 0.2 A; 100 A/µs

on-state current after dIG/dt = 0.2 A/µs

triggering
I
V
P
P

T
T

GM

GM
GM
G(AV)

stg
j

Peak gate current - 2 A

Peak gate voltage - 5 V

Peak gate power - 5 W

Average gate power over any 20 ms - 0.5 W

period
Storage temperature -40 150 ˚C
Operating junction - 125 ˚C
temperature

1

800 V

T1T2

G

1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may
switch to the on-state. The rate of rise of current should not exceed 15 A/µs.

October 1999 1 Rev 1.200

Philips Semiconductors Objective specification

Three quadrant triacs BTA212B series D, E and F
guaranteed commutation

THERMAL RESISTANCES

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

R

th j-mb

R

th j-a

STATIC CHARACTERISTICS

Tj = 25 ˚C unless otherwise stated

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

I

GT

I

L

Thermal resistance full cycle - - 1.5 K/W
junction to mounting base half cycle - - 2.0 K/W
Thermal resistance in free air - 60 - K/W
junction to ambient

BTA212B- ...D ...E ...F

Gate trigger current

2

VD = 12 V; IT = 0.1 A

T2+ G+ - - 5 10 25 mA
T2+ G- - - 5 10 25 mA
T2- G- - - 5 10 25 mA

Latching current VD = 12 V; IGT = 0.1 A

T2+ G+ - - 15 20 25 mA
T2+ G- - - 25 30 40 mA
T2- G- - - 25 30 40 mA

I

H

V

T

V

GT

Holding current VD = 12 V; IGT = 0.1 A - - 15 25 30 mA
On-state voltage IT = 17 A - 1.3 1.6 V

Gate trigger voltage VD = 12 V; IT = 0.1 A - 0.7 1.5 V

VD = 400 V; IT = 0.1 A; 0.25 0.4 - V

Tj = 125 ˚C

I

D

Off-state leakage current VD = V

; - 0.1 0.5 mA

DRM(max)

Tj = 125 ˚C

DYNAMIC CHARACTERISTICS

Tj = 25 ˚C unless otherwise stated

SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT

BTA212B- ...D ...E ...F

dVD/dt Critical rate of rise of VDM = 67% V

off-state voltage Tj = 110 ˚C; exponential

waveform; gate open

circuit

dI

/dt Critical rate of change of VDM = 400 V; Tj = 110 ˚C; 1.8 3.5 4.5 - - A/ms

com

dI

/dt Critical rate of change of VDM = 400 V; Tj = 110 ˚C; 4.3 5.3 6.3 - - A/ms

com

commutating current I

commutating current I

= 12 A;

T(RMS)

dV

/dt = 20v/µs; gate

com

open circuit

= 12 A;

T(RMS)

dV

/dt = 0.1v/µs; gate

com

open circuit

;306070--V/µs

DRM(max)

t

gt

Gate controlled turn-on ITM = 12 A; VD = V

;- - - 2 - µs

DRM(max)

time IG = 0.1 A; dIG/dt = 5 A/µs

2 Device does not trigger in the T2-, G+ quadrant.

October 1999 2 Rev 1.200

Philips Semiconductors Objective specification

Three quadrant triacs BTA212B series D, E and F
guaranteed commutation

MECHANICAL DATA

Dimensions in mm
Net Mass: 1.4 g

2.54 (x2)

MOUNTING INSTRUCTIONS

Dimensions in mm

10.3 max

11 max

15.4

0.85 max
(x2)

4.5 max

1.4 max

0.5

Fig.1. SOT404 : centre pin connected to mounting base.

11.5

2.5

Notes

1. Plastic meets UL94 V0 at 1/8".

9.0

17.5

2.0

3.8

5.08

Fig.2. SOT404 : minimum pad sizes for surface mounting

.

October 1999 3 Rev 1.200

Philips Semiconductors Objective specification

Three quadrant triacs BTA212B series D, E and F
guaranteed commutation

DEFINITIONS

Data sheet status

Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.

Limiting values

Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and
operation of the device at these or at any other conditions above those given in the Characteristics sections of
this specification is not implied. Exposure to limiting values for extended periods may affect device reliability.

Application information

Where application information is given, it is advisory and does not form part of the specification.

 Philips Electronics N.V. 1999

All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the
copyright owner.

The information presented in this document does not form part of any quotation or contract, it is believed to be
accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under patent or other
industrial or intellectual property rights.

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices or systems where malfunction of these
products can be reasonably expected to result in personal injury. Philips customers using or selling these products
for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting
from such improper use or sale.

October 1999 4 Rev 1.200