Glass passivated thyristors in a fullSYMBOLPARAMETERMAX. MAX. MAX. UNIT
pack, plastic envelope, intended for
use in applications requiring highBT152X-400R600R800R
bidirectionalblockingvoltageV
capability and high thermal cyclingV
performance. Typical applicationsI
include motor control, industrial andI
domestic lighting, heating and staticI
switching.current
PINNING - SOT186APIN CONFIGURATIONSYMBOL
,Repetitive peak off-state450650800V
DRM
RRM
T(AV)
T(RMS)
TSM
voltages
Average on-state current131313A
RMS on-state current202020A
Non-repetitive peak on-state200200200A
PINDESCRIPTION
1cathode
case
ak
2anode
3gate
case isolated
123
g
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum System (IEC 134).
SYMBOLPARAMETERCONDITIONSMIN.MAX.UNIT
-400R -600R -800R
V
DRM
I
T(AV)
I
T(RMS)
I
TSM
Repetitive peak off-state-4501650
voltages
Average on-state currenthalf sine wave; Ths ≤ 43 ˚C-13A
RMS on-state currentall conduction angles-20A
Non-repetitive peakhalf sine wave; Tj = 25 ˚C prior to
on-state currentsurge
Peak gate current-5A
Peak gate voltage-5V
Peak reverse gate voltage-5V
Peak gate power-20W
Average gate powerover any 20 ms period-0.5W
Storage temperature-40150˚C
Operating junction-125˚C
temperature
1
800V
1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the thyristor may
switch to the on-state. The rate of rise of current should not exceed 15 A/µs.
October 19971Rev 1.100
Page 2
Philips SemiconductorsProduct specification
ThyristorsBT152X series
ISOLATION LIMITING VALUE & CHARACTERISTIC
Ths = 25 ˚C unless otherwise specified
SYMBOLPARAMETERCONDITIONSMIN.TYP.MAX.UNIT
V
isol
C
isol
THERMAL RESISTANCES
SYMBOLPARAMETERCONDITIONSMIN.TYP.MAX.UNIT
R
th j-hs
R
th j-hs
R
th j-a
R.M.S. isolation voltage from all f = 50-60 Hz; sinusoidal-2500V
three terminals to externalwaveform;
heatsinkR.H. ≤ 65% ; clean and dustfree
Capacitance from T2 to external f = 1 MHz-10-pF
heatsink
Thermal resistancewith heatsink compound--4.0K/W
junction to heatsink
Thermal resistancewithout heatsink compound--5.5K/W
junction to heatsink
Thermal resistancein free air-55-K/W
junction to ambient
Fig.4. Maximum permissible non-repetitive peak
on-state current I
sinusoidal currents, f = 50 Hz.
IT(RMS) / A
50
40
30
20
10
0
0.010.1110
, versus number of cycles, for
TSM
BT152
surge duration / s
Fig.5. Maximum permissible repetitive rms on-state
current I
, versus surge duration, for sinusoidal
T(RMS)
currents, f = 50 Hz; Ths ≤ 43˚C.
IT(RMS) / A
25
20
15
10
5
0
-50050100150
BT152X
43 C
Ths / C
Fig.3. Maximum permissible rms current I
versus heatsink temperature Ths.
T(RMS)
,
VGT(Tj)
VGT(25 C)
1.6
1.4
1.2
1
0.8
0.6
0.4
-50050100150
BT151
Tj / C
Fig.6. Normalised gate trigger voltage
VGT(Tj)/ VGT(25˚C), versus junction temperature Tj.
October 19973Rev 1.100
Page 4
Philips SemiconductorsProduct specification
ThyristorsBT152X series
IGT(Tj)
IGT(25 C)
3
2.5
2
1.5
1
0.5
0
-50050100150
BT152
Tj / C
Fig.7. Normalised gate trigger current
IGT(Tj)/ IGT(25˚C), versus junction temperature T
IL(Tj)
2.5
1.5
0.5
IL(25 C)
3
2
1
BT145
IT / A
50
Tj = 125 C
Tj = 25 C
40
Vo = 1.12 V
Rs = 0.015 ohms
30
20
10
0
00.511.52
BT152
VT / V
typ
max
Fig.10. Typical and maximum on-state characteristic.
.
j
Zth j-hs (K/W)
10
with heatsink compound
without heatsink compound
1
0.1
0.01
BT152X
t
P
p
D
t
0
-50050100150
Tj / C
Fig.8. Normalised latching current IL(Tj)/ IL(25˚C),
versus junction temperature T
IH(Tj)
IH(25 C)
3
2.5
2
1.5
1
0.5
0
-50050100150
BT152
Tj / C
.
j
Fig.9. Normalised holding current IH(Tj)/ IH(25˚C),
versus junction temperature T
.
j
0.001
10us0.1ms1ms10ms0.1s1s10s
Fig.11. Transient thermal impedance Z
dVD/dt (V/us)
10000
1000
100
10
050100150
tp / s
pulse width tp.
Tj / C
, versus
th j-hs
RGK = 100 Ohms
gate open circuit
Fig.12. Typical, critical rate of rise of off-state voltage,
dVD/dt versus junction temperature Tj.
October 19974Rev 1.100
Page 5
Philips SemiconductorsProduct specification
ThyristorsBT152X series
MECHANICAL DATA
Dimensions in mm
Net Mass: 2 g
10.3
Recesses (2x)
2.5
0.8 max. depth
3 max.
not tinned
13.5
min.
0.4
M
max
3.2
3.0
123
5.08
2.8
2.54
15.8
max.
3
19
max.
seating
plane
0.5
2.5
4.6
max
2.9 max
6.4
0.6
2.5
15.8
max
Fig.13. SOT186A; The seating plane is electrically isolated from all terminals.
1.3
1.0 (2x)
0.9
0.7
Notes
1. Refer to mounting instructions for F-pack envelopes.
2. Epoxy meets UL94 V0 at 1/8".
October 19975Rev 1.100
Page 6
Philips SemiconductorsProduct specification
ThyristorsBT152X series
DEFINITIONS
Data sheet status
Objective specificationThis data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specificationThis data sheet contains final product specifications.
Limiting values
Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and
operation of the device at these or at any other conditions above those given in the Characteristics sections of
this specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
Philips Electronics N.V. 1997
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the
copyright owner.
The information presented in this document does not form part of any quotation or contract, it is believed to be
accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under patent or other
industrial or intellectual property rights.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices or systems where malfunction of these
products can be reasonably expected to result in personal injury. Philips customers using or selling these products
for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting
from such improper use or sale.
October 19976Rev 1.100
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.