Glass passivated, sensitive gateSYMBOLPARAMETERMAX. MAX. UNIT
triacsinaplastic envelopesuitablefor
surface mounting, intended for use inBT136S (or BT136M)-500D600D
generalpurposebidirectionalV
switchingandphasecontrolI
applications.These devicesareI
intended to be interfaced directly toNon-repetitive peak on-state current
DRM
T(RMS)
TSM
microcontrollers,logicintegrated
circuits and other low power gate
trigger circuits.
PINNING - SOT428PIN CONFIGURATIONSYMBOL
Repetitive peak off-state 500600V
voltages44A
RMS on-state current2525A
BT136M series D
PINStandard Alternative
tab
NUMBERSM
1MT1gate
T1T2
2MT2MT2
3gateMT1
tabMT2MT2
2
1
3
G
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum System (IEC 134).
SYMBOLPARAMETERCONDITIONSMIN.MAX.UNIT
-500-600
V
DRM
Repetitive peak off-state-500
voltages
I
T(RMS)
I
TSM
RMS on-state currentfull sine wave; Tmb ≤ 107 ˚C-4A
Non-repetitive peakfull sine wave; Tj = 25 ˚C prior to
on-state currentsurge
on-state current afterdIG/dt = 0.2 A/µs
triggeringT2+ G+-50A/µs
I
V
P
P
T
T
GM
GM
GM
G(AV)
stg
j
Peak gate current-2A
Peak gate voltage-5V
Peak gate power-5W
Average gate powerover any 20 ms period-0.5W
Storage temperature-40150˚C
Operating junction-125˚C
temperature
1
T2+ G--50A/µs
T2- G--50A/µs
T2- G+-10A/µs
600
1
V
1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may
switch to the on-state. The rate of rise of current should not exceed 3 A/µs.
July 19971Rev 1.000
Page 2
Philips SemiconductorsProduct specification
TriacsBT136S series D
logic level
THERMAL RESISTANCES
SYMBOLPARAMETERCONDITIONSMIN.TYP.MAX.UNIT
R
th j-mb
R
th j-a
STATIC CHARACTERISTICS
Tj = 25 ˚C unless otherwise stated
SYMBOLPARAMETERCONDITIONSMIN.TYP.MAX.UNIT
I
GT
I
L
I
H
V
T
V
GT
I
D
Thermal resistancefull cycle--3.0K/W
junction to mounting base half cycle--3.7K/W
Thermal resistancepcb (FR4) mounted; footprint as in Fig.14-75-K/W
junction to ambient
Fig.5. Maximum permissible repetitive rms on-state
current I
VGT(25 C)
1.6
1.4
1.2
1
0.8
0.6
0.4
-50050100150
, versus surge duration, for sinusoidal
T(RMS)
currents, f = 50 Hz; Tmb ≤ 107˚C.
VGT(Tj)
BT136
Tj / C
Fig.6. Normalised gate trigger voltage
VGT(Tj)/ VGT(25˚C), versus junction temperature Tj.
July 19973Rev 1.000
Page 4
Philips SemiconductorsProduct specification
TriacsBT136S series D
logic level
BT136M series D
IGT(Tj)
IGT(25 C)
3
2.5
2
1.5
1
0.5
0
-50050100150
BT136D
Tj / C
T2+ G+
T2+ GT2- GT2- G+
Fig.7. Normalised gate trigger current
IGT(Tj)/ IGT(25˚C), versus junction temperature T
IL(Tj)
2.5
1.5
IL(25 C)
3
2
1
TRIAC
IT / A
12
Tj = 125 C
Tj = 25 C
10
Vo = 1.27 V
Rs = 0.091 ohms
8
6
4
2
0
00.511.522.53
BT136
typmax
VT / V
Fig.10. Typical and maximum on-state characteristic.
.
j
Zth j-mb (K/W)
10
1
0.1
BT136
P
D
unidirectional
bidirectional
t
p
0.5
0
-50050100150
Tj / C
Fig.8. Normalised latching current IL(Tj)/ IL(25˚C),
versus junction temperature T
IH(Tj)
IH(25C)
3
2.5
2
1.5
1
0.5
0
-50050100150
TRIAC
Tj / C
.
j
Fig.9. Normalised holding current IH(Tj)/ IH(25˚C),
versus junction temperature T
.
j
t
0.01
10us0.1ms1ms10ms0.1s1s10s
tp / s
Fig.11. Transient thermal impedance Z
pulse width tp.
dVD/dt (V/us)
1000
100
10
1
050100150
Tj / C
th j-mb
, versus
Fig.12. Typical, critical rate of rise of off-state voltage,
dVD/dt versus junction temperature Tj.
July 19974Rev 1.000
Page 5
Philips SemiconductorsProduct specification
TriacsBT136S series D
logic level
MECHANICAL DATA
BT136M series D
Dimensions in mm
Net Mass: 1.1 g
2.285 (x2)
MOUNTING INSTRUCTIONS
Dimensions in mm
1
seating plane
6.73 max
tab
2
3
1.1
6.22 max
0.5 min
0.8 max
(x2)
2.38 max
0.93 max
10.4 max
0.3
0.5
Fig.13. SOT428 : centre pin connected to tab.
7.0
5.4
4 min
4.6
0.5
7.0
2.15
2.5
4.57
Fig.14. SOT428 : minimum pad sizes for surface mounting
1.5
.
Notes
1. Plastic meets UL94 V0 at 1/8".
July 19975Rev 1.000
Page 6
Philips SemiconductorsProduct specification
TriacsBT136S series D
logic level
DEFINITIONS
Data sheet status
Objective specificationThis data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specificationThis data sheet contains final product specifications.
Limiting values
Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and
operation of the device at these or at any other conditions above those given in the Characteristics sections of
this specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
Philips Electronics N.V. 1997
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the
copyright owner.
The information presented in this document does not form part of any quotation or contract, it is believed to be
accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under patent or other
industrial or intellectual property rights.
BT136M series D
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices or systems where malfunction of these
products can be reasonably expected to result in personal injury. Philips customers using or selling these products
for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting
from such improper use or sale.
July 19976Rev 1.000
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.