Page 1
Magnetic Field Sensor
for pneumatic cylinders
BIM-UNT-AP6X2-H1141
■ For T-groove cylinders without mount-
ing accessories
■ Optional accessories for mounting on
other cylindrical housings.
■ One-hand mounting possible
■ Fine adjustment tool and stopper direct-
ly mountable on the sensor
■ Stable mounting
■ Magneto-resistive sensor
■ DC 3-wire, 10…30 VDC
■ NO contact, PNP output
■ Male connector, M12 x 1
Type designation BIM-UNT-AP6X2-H1141
Ident-No. 4685726
Pass speed
Repeatability
Temperature drift
Hysteresis
Ambient temperature -25…+70 °C
Operating voltage 10…30 VDC
Residual ripple
DC rated operational current
No-load current I
Residual current
Isolation test voltage
Short-circuit protection yes/ Cyclic
Voltage drop at I
Wire breakage/Reverse polarity protection yes/ Complete
Output function 3-wire, NO contact, PNP
Switching frequency 1 kHz
Design Rectangular,UNT
Dimensions 30 x 5 x 22 mm
Housing material Plastic, PP
Active area material Plastic, PP
Tightening torque fixing screw 0.4 Nm
Electrical connection Connector, M12 × 1
Vibration resistance 55 Hz (1 mm)
Shock resistance 30 g (11 ms)
Protection class IP67
MTTF 2283 years acc. to SN 29500 (Ed. 99) 40 °C
Packaging unit 1
Mounting on the following profiles .
Cylindrical design
0
e
ð 10 m/s
ð ± 0.1 mm
ð 0.1 mm
ð 1 mm
ð 10 % U
ss
ð 150 mA
ð 15 mA
ð 0.1 mA
ð 0.5 kV
ð 1.8 V
E N K F
Wiring Diagram
Functional principle
Magnetic field sensors are activated by magnetic fields and are used, in particular, for the
detection of the piston position in pneumatic
cylinders. As magnetic fields can permeate
non-magnetizable metals, they detect a permanent magnet attached to the piston through
the aluminium cylinder wall.
Power-on indication LED,Green
Switching state LED,Yellow
Edition • Rev. A • 2018-03-28T18:52:40+02:00
1 / 5 TURCK Inc. ñ 3000 Campus Drive Minneapolis, MN 55441-2656 ñ Phone: 763-553-7300 ñ Application Support: 1-800-544-7769 ñ Fax 763-553-0708 ñ www.turck.com
Page 2
Magnetic Field Sensor
for pneumatic cylinders
BIM-UNT-AP6X2-H1141
Mounting instructions/Description Mounting instructions
Insert the sensor laterally in the groove with the tip first.
Once the correct postion is attained click the sensor in
the groove. Finally, screw the sensor tight. Mount the
sensors as follows using the patented wing screw: The
wing screw features a left-hand female thread. Two
small plastic lips keep the screw in position, ready-to-
install. Turn the screw clockwise. The screw moves out
of the thread and hits the upper grooves with the wings.
The sensor is thus pressed down and locked. Use a
standard screw driver or a 1.5 mm Allen key to fasten
the screw with a quarter turn. A fixing torque of 0.4 Nm
is sufficient for safe mounting without damaging the
cylinder. Mounting accessories for other cylinder sizes
have to be ordered separately.
Edition • Rev. A • 2018-03-28T18:52:40+02:00
2 / 5 TURCK Inc. ñ 3000 Campus Drive Minneapolis, MN 55441-2656 ñ Phone: 763-553-7300 ñ Application Support: 1-800-544-7769 ñ Fax 763-553-0708 ñ www.turck.com
Page 3
Magnetic Field Sensor
for pneumatic cylinders
BIM-UNT-AP6X2-H1141
Accessories
Type code Ident-No. Description
KLZ1-INT CLAMP 6970410 Accessories for mounting the sensors BIM-INT and BIM-UNT
on tie-rod cylinders; Cylinder diameter: 32…40 mm; material:
Aluminium; Further mounting accessories for other cylinder
diameters on request
KLZ2-INT CLAMP 6970411 Accessories for mounting the sensors BIM-INT and BIM-UNT
on tie-rod cylinders; Cylinder diameter: 50…63 mm; material:
Aluminium; Further mounting accessories for other cylinder
diameters on request
UNT-STOPPER 4685751
UNT-ADJUSTING
BRACKET
KLRC-UNT1 6970626
4685750
Accessories for finetuning the switchpoint on N T-groove
cylinders; snap-locked in the BIM-UNT fixture; suited for mul-
tiple use; material: plastic
Accessories for finetuning the switchpoint on N T-groove
cylinders; snap-locked in the BIM-UNT fixture; suited for mul-
tiple use; material: metal/plastic
Accessories for mounting on E cylinders; diameter: 8…25
mm; material: PA 6I/6T / nickel silver; Fire-hazard classifica-
tion acc. to UL94 - V2
Edition • Rev. A • 2018-03-28T18:52:40+02:00
3 / 5 TURCK Inc. ñ 3000 Campus Drive Minneapolis, MN 55441-2656 ñ Phone: 763-553-7300 ñ Application Support: 1-800-544-7769 ñ Fax 763-553-0708 ñ www.turck.com
Page 4
Magnetic Field Sensor
for pneumatic cylinders
BIM-UNT-AP6X2-H1141
Accessories
Type code Ident-No. Description
KLRC-UNT2 6970627
Accessories for mounting on E cylinders; diameter: 25…63
mm; material: PA 6I/6T / nickel silver; Fire-hazard classifica-
tion acc. to UL94 - V2
KLRC-UNT3 6970628
KLRC-UNT4 6970629
KLDT-UNT2 6913351 Accessories for mounting the BIM-UNT sensor on dovetail
Accessories for mounting the BIM-UNT sensor on E round
cylinders; diameter: 63…130 mm; material: PA 6I/6T / nickel
silver; Fire-hazard classification acc. to UL94 - V2
Accessories for mounting the BIM-UNT sensor on E round
cylinders; diameter: 130…250 mm; material: PA 6I/6T / nickel
silver; Fire-hazard classification acc. to UL94 - V2
cylinders; groove width: 7 mm; material: PPS
KLDT-UNT3 6913352
Edition • Rev. A • 2018-03-28T18:52:40+02:00
4 / 5 TURCK Inc. ñ 3000 Campus Drive Minneapolis, MN 55441-2656 ñ Phone: 763-553-7300 ñ Application Support: 1-800-544-7769 ñ Fax 763-553-0708 ñ www.turck.com
Accessories for mounting the BIM-UNT sensor on K dove-
tail groove cylinders; groove width: 9.4 mm; material: PPS
Page 5
Magnetic Field Sensor
for pneumatic cylinders
BIM-UNT-AP6X2-H1141
Accessories
Type code Ident-No. Description
KLDT-UNT6 6913355
Accessories for mounting on K dovetail groove cylinders;
groove width: 7.35 mm; material: PPS
Edition • Rev. A • 2018-03-28T18:52:40+02:00
5 / 5 TURCK Inc. ñ 3000 Campus Drive Minneapolis, MN 55441-2656 ñ Phone: 763-553-7300 ñ Application Support: 1-800-544-7769 ñ Fax 763-553-0708 ñ www.turck.com
Loading...