Datasheet BCC400PS28EL, BCC400PS28E, BCC400PS24L, BCC400PS24EL, BCC400PS24E Datasheet (IPSI)

PRELIMINARY

Q4 2003

••

Input

Input Voltage • 90-264 VAC
Harmonics • EN61000-3-2 (Active PFC)
Fuse Protection • Input PCB mounted

Output

Output Power • See Table
Output Voltage • See Table
Output Voltage • -6 to +10% Vnom

Adjustment
Output Current • See Table
Output Set Tolerance • ±1% nominal
Load Regulation • See Table
Ripple & Noise • <150 mV pk-pk, 20 MHz bandwidth
Hold Up Time • 10 ms at low line (90 V), rated output
Minimum Load • No minimum load
Overload • 105-135% constant current limiting

Protection with auto recovery
Overvoltage • 105-140% Vnom except 3.3 V module

Protection 130-166%
Remote Sense • Compensates for lead drops of

up to 500 mV on output

Remote ON/OFF • A logic ‘0’ on the ROF connection

electronically disables the output
(contact sales for full set of
application notes)

General

Earth Leakage • In accordance with EN60950
Current (1.5 mA max)

Redundancy & • Up to 3 off modules can be connected
Current Sharing in parallel modules sharing within 10%

Total output power derates by 10%

Environmental

Operating • -20 °C to +70 °C, with baseplate
Temperature maintained below +83 °C utilizing

system cooling, -40 °C option available
add suffix ‘L’ to model number

Storage • -40 °C to +85 °C
Temperature

Temperature • 0.05%/°C
Coefficient

Relative Humidity • 20-95% non-condensing,

units can be conformally coated for
high humidity environments
add suffix ‘E’ to model number

Cooling • Conduction via 4 mm thick

aluminum baseplate

Shock & Vibration • 10-500 Hz, 2 G 10 min/1 cycle,

period for 60 mins on each axis

EMC & Safety

EMC Emissions • EN55022 Level B conducted
EMC Immunity • EN61000-4-4 level 3

EN61000-4-5 level 3
Safety Approvals • EN60950
CE Mark Directives • CE Marked to LVD

200-400 Watts

BCC Series

AC/DC Industrial Type

Specification

•

Baseplate Cooled

•

Wide Operating Temp

•

ETSI, EMC & Environmental Compliant

•

Simple Parallel Operation

•

Active PFC

•

Remote ON/OFF

•

Low Temperature Option

Intelligent Design Quality Product

XPiQ inc.

* Preliminary datasheet - see website for current specs

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XPiQ.com

BCC.qxd 6/6/03 3:27 pm Page 1

Remote Local
SW1 A (1) ON OFF
SW1 B (2) ON OFF
SW1 C (3) OFF ON
SW1 D (4) OFF ON

Mechanical Details

Examples of parallel operation

Current and Voltage balance pins are used to connect units in parallel - see drawing.
Remote on/off: Output is on with pin left floating, pull pin down to -Output to turn
output off.

Temp Warning: When baseplate is in normal temperature range, output is 5 V
typical; goes low, (0.5 V @ 5 mA), when baseplate exceeds safe level.

Remote sense pins are used to compensate for lead drops. For up to 0.5 V max.
When not used, move switch SW1 to local positions. See below for switch positions.

The BCC series is approximately 80% efficient so for 400 W load consumption,
the cooling system used will have to be able to absorb 100 W while maintaining the
baseplate to a maximum of +83 °C.

Output:
Power output +ve and -ve by M6 studs.

Use appropriate ring terminals and wire for the load current.
Signal connections on two 0.1" headers (PL3 & PL4).
Mating Housing: Molex 22-01-2065.
Mating Crimp: Molex 08-50-0032.

Input:
AMP Mat'n'lok 3 way.

Mating housing AMP 350766-1.
Socket crimp AMP 926893-1.
Pin 1: Live
Pin 2: Earth
Pin 3: Neutral

Output Output Output Output Load Model

Power Voltage Current Regulation Number
165 W 3.3 V 50.0 A 1.5% BCC200PS03
200 W 5.0 V 40.0 A 1.5% BCC200PS05
210 W 7.5 V 28.0 A 1.5% BCC200PS07
240 W 12.0 V 20.0 A 1.5% BCC200PS12
264 W 3.3 V 80.0 A 1.5% BCC400PS03
400 W 5.0 V 80.0 A 1.5% BCC400PS05
405 W 7.5 V 54.0 A 1.5% BCC400PS07
408 W 12.0 V 34.0 A 1.0% BCC400PS12
405 W 15.0 V 27.0 A 1.0% BCC400PS15
396 W 18.0 V 22.0 A 1.0% BCC400PS18
408 W 24.0 V 17.0 A 1.0% BCC400PS24
406 W 28.0 V 14.5 A 1.0% BCC400PS28

OUTPUT VOLTAGE & CURRENT RATINGS BCC

Remote Sense Switchers

Application Notes

Contact sales office for a full
set of Application Notes.

Accessories

1. For Input and Output Connector Kit - order part ‘BCC connector kit’.

2. For Thermal Pad, order part ‘BCC Therm’.

PL3 Connections

Pin Function

1 Current Balance
2 Voltage Balance
3 Trim
4 -Remote Sense
5 +Remote Sense
6 Remote on/off

PL4 Connections

Pin Function

1 Current Balance
2 Voltage Balance
3 Trim
4 -Remote Sense
5 +Remote Sense
6 Temp Warning

1. For -40 °C operating temperature, add suffix ‘L’ to model number.

2. For conformally coated option, add suffix ‘E’ to model number.

3. Part numbers in bold are standard stock models, all others are build to order.

Notes

•

* Preliminary datasheet - see website for current specs

PH: 508 429.9883

FAX: [phone]

Email: [e-mail]

Holliston, MA 01746 USA

www.XPiQ.com

BCC.qxd 6/6/03 3:27 pm Page 2