Datasheet BCC400PS28EL, BCC400PS28E, BCC400PS24L, BCC400PS24EL, BCC400PS24E Datasheet (IPSI)

...

Download

Page 1

PRELIMINARY

Q4 2003

••

Input

Input Voltage • 90-264 VAC Harmonics • EN61000-3-2 (Active PFC) Fuse Protection • Input PCB mounted

Output

Output Power • See Table Output Voltage • See Table Output Voltage • -6 to +10% Vnom

Adjustment Output Current • See Table Output Set Tolerance • ±1% nominal Load Regulation • See Table Ripple & Noise • <150 mV pk-pk, 20 MHz bandwidth Hold Up Time • 10 ms at low line (90 V), rated output Minimum Load • No minimum load Overload • 105-135% constant current limiting

Protection with auto recovery Overvoltage • 105-140% Vnom except 3.3 V module

Protection 130-166% Remote Sense • Compensates for lead drops of

up to 500 mV on output

Remote ON/OFF • A logic ‘0’ on the ROF connection

electronically disables the output (contact sales for full set of application notes)

General

Earth Leakage • In accordance with EN60950 Current (1.5 mA max)

Redundancy & • Up to 3 off modules can be connected Current Sharing in parallel modules sharing within 10%

Total output power derates by 10%

Environmental

Operating • -20 °C to +70 °C, with baseplate Temperature maintained below +83 °C utilizing

system cooling, -40 °C option available add suffix ‘L’ to model number

Storage • -40 °C to +85 °C Temperature

Temperature • 0.05%/°C Coefficient

Relative Humidity • 20-95% non-condensing,

units can be conformally coated for high humidity environments add suffix ‘E’ to model number

Cooling • Conduction via 4 mm thick

aluminum baseplate

Shock & Vibration • 10-500 Hz, 2 G 10 min/1 cycle,

period for 60 mins on each axis

EMC & Safety

EMC Emissions • EN55022 Level B conducted EMC Immunity • EN61000-4-4 level 3

EN61000-4-5 level 3 Safety Approvals • EN60950 CE Mark Directives • CE Marked to LVD

200-400 Watts

BCC Series

AC/DC Industrial Type

Specification

•

Baseplate Cooled

•

Wide Operating Temp

•

ETSI, EMC & Environmental Compliant

•

Simple Parallel Operation

•

Active PFC

•

Remote ON/OFF

•

Low Temperature Option

Intelligent Design Quality Product

XPiQ inc.

* Preliminary datasheet - see website for current specs

PH: 508 429.9883

FAX: 800 226.2100

Email: [email protected]

Holliston, MA 01746 USA

www.XPiQ.com

BCC.qxd 6/6/03 3:27 pm Page 1

Page 2

Remote Local SW1 A (1) ON OFF SW1 B (2) ON OFF SW1 C (3) OFF ON SW1 D (4) OFF ON

Mechanical Details

Examples of parallel operation

Current and Voltage balance pins are used to connect units in parallel - see drawing. Remote on/off: Output is on with pin left floating, pull pin down to -Output to turn output off.

Temp Warning: When baseplate is in normal temperature range, output is 5 V typical; goes low, (0.5 V @ 5 mA), when baseplate exceeds safe level.

Remote sense pins are used to compensate for lead drops. For up to 0.5 V max. When not used, move switch SW1 to local positions. See below for switch positions.

The BCC series is approximately 80% efficient so for 400 W load consumption, the cooling system used will have to be able to absorb 100 W while maintaining the baseplate to a maximum of +83 °C.

Output: Power output +ve and -ve by M6 studs.

Use appropriate ring terminals and wire for the load current. Signal connections on two 0.1" headers (PL3 & PL4). Mating Housing: Molex 22-01-2065. Mating Crimp: Molex 08-50-0032.

Input: AMP Mat'n'lok 3 way.

Mating housing AMP 350766-1. Socket crimp AMP 926893-1. Pin 1: Live Pin 2: Earth Pin 3: Neutral

Output Output Output Output Load Model

Power Voltage Current Regulation Number 165 W 3.3 V 50.0 A 1.5% BCC200PS03 200 W 5.0 V 40.0 A 1.5% BCC200PS05 210 W 7.5 V 28.0 A 1.5% BCC200PS07 240 W 12.0 V 20.0 A 1.5% BCC200PS12 264 W 3.3 V 80.0 A 1.5% BCC400PS03 400 W 5.0 V 80.0 A 1.5% BCC400PS05 405 W 7.5 V 54.0 A 1.5% BCC400PS07 408 W 12.0 V 34.0 A 1.0% BCC400PS12 405 W 15.0 V 27.0 A 1.0% BCC400PS15 396 W 18.0 V 22.0 A 1.0% BCC400PS18 408 W 24.0 V 17.0 A 1.0% BCC400PS24 406 W 28.0 V 14.5 A 1.0% BCC400PS28

OUTPUT VOLTAGE & CURRENT RATINGS BCC

Remote Sense Switchers

Application Notes

Contact sales office for a full set of Application Notes.

Accessories

1. For Input and Output Connector Kit - order part ‘BCC connector kit’.

2. For Thermal Pad, order part ‘BCC Therm’.

PL3 Connections

Pin Function

1 Current Balance 2 Voltage Balance 3 Trim 4 -Remote Sense 5 +Remote Sense 6 Remote on/off

PL4 Connections

Pin Function

1 Current Balance 2 Voltage Balance 3 Trim 4 -Remote Sense 5 +Remote Sense 6 Temp Warning

1. For -40 °C operating temperature, add suffix ‘L’ to model number.

2. For conformally coated option, add suffix ‘E’ to model number.

3. Part numbers in bold are standard stock models, all others are build to order.

Notes

•