Datasheet AZ10EP16VSTR2, AZ10EP16VSTR1, AZ10EP16VST, AZ10EP16VSLR2, AZ10EP16VSLR1 Datasheet (AZMIC)

AZ10EP16VS

AZ100EP16VS

ECL/PECL Differential Receiver with Variable Output Swing

1630 S. STAPLEY DR., SUITE 125 • MESA, ARIZONA 85204 • USA • [phone] • FAX [phone]

www.azmicrotek.com

ARIZONA MICROTEK, INC.

FEATURES

• Silicon-Germanium for High Speed Operation

• 150ps Typical Propagation Delay

• AZ100EP16VS Functionally Equivalent to ON

Semiconductor MC100EP16VS at 3.3V

• Available in a 3x3mm MLP Package

DESCRIPTION

The AZ10/100EP16VS is a Silicon–Germanium (SiGe) differential receiver with variable output swing. The
EP16VS has functionality and output transition times similar to the EP16, with an input that controls the amplitude
of the Q/Q¯ outputs.

The operational range of the EP16VS control input, V

CTRL

, is from V

REF

(full swing) to VCC (min. swing).

Maximum swing is achieved by leaving the V

CTRL

pin open or tied to VEE. Simple control of the output swing can be

obtained by a variable resistor between the V

REF

and VCC pins, with the wiper driving V

CTRL

. Typical application

circuits and results are described in this Data Sheet.

The EP16VS provides a V

REF

output for a DC bias for AC coupling to the device. The V

REF

pin should be used

only as a bias for the EP16VS as its current sink/source capability is limited. Whenever used, the V

REF

pin should

be bypassed to ground via a 0.01µF capacitor.

Under open input conditions for D/D¯, the Q/Q¯ outputs are not guaranteed.
NOTE: Specifications in ECL/PECL tables are valid when thermal equilibrium is established.

PACKAGE AVAILABILITY

PACKAGE PART NO. MARKING

MLP 8 AZ10EP16VSL AZM16E
MLP 8 T&R AZ10EP16VSLR1 AZM16E
MLP 8 T&R AZ10EP16VSLR2 AZM16E
MLP 8 AZ100EP16VSL AZM16F
MLP 8 T&R AZ100EP16VSLR1 AZM16F
MLP 8 T&R AZ100EP16VSLR2 AZM16F
SOIC 8 AZ10EP16VSD AZM10EP16VS
SOIC 8 T&R AZ10EP16VSDR1 AZM10EP16VS
SOIC 8 T&R AZ10EP16VSDR2 AZM10EP16VS
SOIC 8 AZ100EP16VSD AZM100EP16VS
SOIC 8 T&R AZ100EP16VSDR1 AZM100EP16VS
SOIC 8 T&R AZ100EP16VSDR2 AZM100EP16VS
TSSOP 8 AZ10EP16VST AZTP16VS
TSSOP 8 T&R AZ10EP16VSTR1 AZTP16VS
TSSOP 8 T&R AZ10EP16VSTR2 AZTP16VS
TSSOP 8 AZ100EP16VST AZHP16VS
TSSOP 8 T&R AZ100EP16VSTR1 AZHP16VS
TSSOP 8 T&R AZ100EP16VSTR2 AZHP16VS

AZ10EP16VS
AZ100EP16VS

November 2001 * REV - 3 www.azmicrotek.com
2

Absolute Maximum Ratings are those values beyond which device life may be impaired.

Symbol Characteristic Rating Unit

VCC PECL Power Supply (VEE = 0V) 0 to +4.5 Vdc

VI PECL Input Voltage (V

EE

= 0V) 0 to +4.5 Vdc

VEE ECL Power Supply (VCC = 0V) -4.5 to 0 Vdc

VI ECL Input Voltage (VCC = 0V) -4.5 to 0 Vdc

I

OUT

Output Current --- Continuous

--- Surge

50

100

mA

TA Operating Temperature Range -40 to +85

°C

T

STG

Storage Temperature Range -65 to +150

°C

10K ECL DC Characteristics (VEE = -3.0V to -3.6V, VCC = GND)

-40°C 0°C 25°C 85°C

Symbol Characteristic

Min Typ Max Min Typ Max Min Typ Max Min Typ Max

Unit

VOH Output HIGH Voltage1 -1085 -835 -1020 -895 -770 -960 -710 mV

VOL

Output LOW Voltage

1

V

CTRL

= V

REF

-2115 -1865 -2050 -1925 -1800 -1990 -1740 mV

VOL

Output LOW Voltage

1

V

CTRL

= V

CC

-1330 -1080 -1265 -1140 -1015 -1205 -915 mV

V

REF

Reference Voltage -1700 -1600 -1500 -1670 -1570 -1470 -1650 -1550 -1450 -1600 -1500 -1400 mV

IIH

Input HIGH Current

D,D¯

V

CTRL

80

400

80

400

80

400

80

400

µA

IIL

Input LOW Current 0.5 0.5 0.5 0.5

µA

IEE Power Supply Current 21 27 36 22 28 37 22 29 38 24 30 40 mA

1. Each output is terminated through a 50Ω resistor to VCC – 2V.

LOGIC DIAGRAM AND PINOUT ASSIGNMENT

PIN DESCRIPTION

PIN FUNCTION

D, D¯ Data Inputs
V

CTRL

Output Swing Control
Q, Q¯ Data Outputs
V

REF

Reference Voltage Output

V

CC

Positive Supply

V

EE

Negative Supply

8

4

5

6

3

2

1

7

V

CC

D

V

EE

Q

Q

V

REF

D

V

CTRL

8 SOIC & 8 TSSOP

MLP 8 (TOP VIEW)

8

5

6

7

4

3

2

1

V

CC

D

V

EE

Q

Q

V

REF

D

V

CTRL

AZ10EP16VS
AZ100EP16VS

November 2001 * REV - 3 www.azmicrotek.com
3

10K LVPECL DC Characteristics (V

EE

= GND, VCC = +3.3V)

-40°C 0°C 25°C 85°C

Symbol Characteristic

Min T

yp

Max Min T

yp

Max Min T

yp

Max Min T

yp

Max

Unit

VOH Output HIGH Voltage

1,2

2215 2465 2280 2405 2530 2340 2590 mV

VOL

Output LOW Voltage

2

V

CTRL

= V

REF

1185 1435 1250 1375 1500 1310 1560 mV

VOL

Output LOW Voltage

2

V

CTRL

= V

CC

1970 2220 2035 2160 2285 2095 2385 mV

V

REF

Reference Voltage 1600 1700 1800 1630 1730 1830 1650 1750 1850 1700 1800 1900 mV

IIH

Input HIGH Current

D,D¯

V

CTRL

80

400

80

400

80

400

80

400

µA

IIL

Input LOW Current 0.5 0.5 0.5 0.5

µA

IEE Power Supply Current 21 27 36 22 28 37 22 29 38 24 30 40 mA

1. For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value.

2. Each output is terminated through a 50Ω resistor to V

CC

– 2V.

100K ECL DC Characteristics (VEE = -3.0V to -3.6V, VCC = GND)

-40°C 0°C 25°C 85°C

Symbol Characteristic

Min Typ Max Min Typ Max Min Typ Max Min Typ Max

Unit

VOH Output HIGH Voltage1 -1095 -890 -1035 -890 -1035 -965 -890 -1035 -890 mV

VOL

Output LOW Voltage

1

V

CTRL

= V

REF

-1925 -1835 -1965 -1775 -1965 -1870 -1775 -1965 -1775 mV

VOL

Output LOW Voltage

1

V

CTRL

= V

CC

-1180 -1045 -1160 -970 -1160 -1065 -970 -1160 -970 mV

V

REF

Reference Voltage -1650 -1450 -1650 -1450 -1650 -1550 -1450 -1650 -1450 mV

IIH

Input HIGH Current

D,D¯

V

CTRL

80

400

80

400

80

400

80

400

µA

IIL

Input LOW Current 0.5 0.5 0.5 0.5

µA

IEE Power Supply Current 20 26 35 21 27 36 22 28 38 25 31 41 mA

1. Each output is terminated through a 50Ω resistor to V

CC

– 2V.

100K LVPECL DC Characteristics (VEE = GND, VCC = +3.3V)

-40°C 0°C 25°C 85°C

Symbol Characteristic

Min T

yp

Max Min T

yp

Max Min T

yp

Max Min T

yp

Max

Unit

VOH Output HIGH Voltage

1,2

3905 4110 3965 4110 3965 4035 4110 3965 4110 mV

VOL

Output LOW Voltage

2

V

CTRL

= V

REF

3075 3165 3035 3225 3035 3130 3225 3035 3225 mV

VOL

Output LOW Voltage

2

V

CTRL

= V

CC

3820 3955 3840 4030 3840 3935 4030 3840 4030 mV

V

REF

Reference Voltage 1650 1850 1650 1850 1650 1750 1850 1650 1850 mV

IIH

Input HIGH Current

D,D¯

V

CTRL

80

400

80

400

80

400

80

400

µA

IIL

Input LOW Current 0.5 0.5 0.5 0.5

µA

IEE Power Supply Current 20 26 35 21 27 36 22 28 38 25 31 41 mA

1. For supply voltages other that 3.3V, use the ECL table values and ADD supply voltage value.

2. Each output is terminated through a 50Ω resistor to V

CC

– 2V.

AZ10EP16VS
AZ100EP16VS

November 2001 * REV - 3 www.azmicrotek.com
4

AC Characteristics (V

EE

= -3.0 to -3.6V, VCC = GND, V

CTRL=VREF

or VEE = GND, VCC = +3.0V to 3.6V, V

CTRL

= V

REF

)

-40°C 0°C 25°C 85°C

Symbol Characteristic

Min Typ Max Min Typ Max Min Typ Max Min Typ Max

Unit

f

max

Maximum Toggle
Frequency

5

>4 >4 >4 >4 GHz

t

PLH

/ t

PHL

Input to Output
Delay

(Diff)

(SE)

100 150

155

240 100 150

155

240 100 150

155

240 120 170

175

280

ps

t

SKEW

Duty Cycle Skew

1

(Diff) 4 20 4 15 4 15 4 15 ps

Vpp Minimum Input Swing2 150 150 150 150 mV

V

CMR

Common Mode Range3

V

EE

+

2.0

V

CC

V

EE

+

2.0

V

CC

V

EE

+

2.0

V

CC

V

EE

+

2.0

V

CC

V

Av Small Signal Gain4 28 dB

tr / tf

Output Rise/Fall Times Q
(20% - 80%)

120 70 120 180 120 180 120 200 ps

1. Duty cycle skew is the difference between a t

PLH

and t

PHL

propagation delay through a device.

2. V

PP

is the minimum peak-to-peak differential input swing for which AC parameters are guaranteed.

3. The V

CMR

range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within

the specified range and the peak-to-peak voltage lies between V

PP

(min) and 1V.

4. Differential input, differential output. 240Ω to V

EE

on Q/Q¯ outputs and V

CTRL

= Open Circuit.

5. See graph below.

Large Signal Performance*

0

100

200

300

400

500

600

700

800

900

1000

0 1000 2000 3000 4000 5000 6000

FREQUENCY (MHz)

V

OUTpp

(mV)

V

CTRL=VCC

V

CTRL=VCC

-2.0V

V

CTRL=VCC

-1.5V

V

CTRL=VCC

-1.0V

V

CTRL=VCC

-0.5V

*Measured using a 750mV differential input source at 50% duty cycle.

AZ10EP16VS
AZ100EP16VS

November 2001 * REV - 3 www.azmicrotek.com
5

Typical AZ100EP16VS Voltage Output Swing at +25C, VEE Nom

(see Figure 1 and Figure 2)

1.240 V (100K ECL)

0

25

50

75

100

0.0 0.4 0.8 1.2 1.6

V

CTRL

(V)

V

SWING

(% pk-pk differential)

%OUT

100K ECL

Figure 2: Alternative Implementation

8

5

6

7

4

3

2

1

V

CC

D

V

EE

Q

Q

V

REF

D

V

CTRL

V

CTRL

50

-2V

50

VSWING

(pk-pk)

Figure 1: Voltage Source Implementation

8

5

6

7

4

3

2

1

V

CC

D

V

EE

Q

Q

V

REF

D

V

CTRL

+ 3.3V

1k

V SWING

(pk-pk)

240

240

AZ10EP16VS
AZ100EP16VS

November 2001 * REV - 3 www.azmicrotek.com
6

MILLIMETERS INCHES

DIM

MIN MAX MIN MAX

A

1.75 0.069

A1

0.10 0.25 0.004 0.010

A2

1.25 1.45 0.049 0.057

A3

0.25 0.01

bp

0.36 0.49 0.014 0.019

c

0.19 0.25 0.0075 0.0100

D

4.8 5.0 0.19 0.20

E

3.8 4.0 0.15 0.16

e

1.27 0.050

HE

5.80 6.20 0.228 0.244

L

1.05 0.041

Lp

0.40 1.00 0.016 0.039

Q

0.60 0.70 0.024 0.028

v

0.25 0.01

w

0.25 0.01

y

0.10 0.004

Z

0.30 0.70 0.012 0.028

θ

0

O

8

O

0

O

8

O

PACKAGE DIAGRAM

SOIC 8

N

OTES:

1. DIMENSIONS D AND E DO NOT
INCLUDE MOLD PROTRUSION.

2. MAXIMUM MOLD PROTRUSION
FOR D IS 0.15mm.

3. MAXIMUM MOLD PROTRUSION
FOR E IS 0.25mm.

AZ10EP16VS
AZ100EP16VS

November 2001 * REV - 3 www.azmicrotek.com
7

PACKAGE DIAGRAM

MLP 8

N

OTES

1. DIMENSIONING AND TOLERANCING
CONFORM TO ASME T14-1994.

2. THE TERMINAL #1 AND PAD
NUMBERING CONVENTION SHALL
CONFORM TO JESD 95-1 SPP-012.

3. DIMENSION b APPLIES TO METALLIZED
PAD AND IS MEASURED BETWEEN 0.25
AND 0.30mm FROM PAD TIP.

4. COPLANARITY APPLIES TO THE
EXPOSED PAD AS WELL AS THE
TERMINALS.

MILLIMETERS

DIM

MIN MAX

A

0.80 1.00

A1

0.00 0.05

A3

0.25 REF

b

0.30 0.35

D

2.90 3.10

D2

1.65 1.95

E

2.90 3.10

E2

1.65 1.95

e

0.65 BSC

L

0.35 0.45

aaa

0.25

bbb

0.10

ccc

0.10

AZ10EP16VS
AZ100EP16VS

November 2001 * REV - 3 www.azmicrotek.com
8

PACKAGE DIAGRAM

TSSOP 8

MILLIMETERS

DIM

MIN MAX

A

1.10

A1

0.05 0.15

A2

0.80 0.95

A3

0.25

bp

0.25 0.45

c

0.15 0.28

D

2.90 3.10

E

2.90 3.10

e

0.65

HE

4.70 5.10

L

0.94

Lp

0.40 0.70

v

0.10

w

0.10

y

0.10

Z

0.35 0.70

θ

0

O

6

O

N

OTES:

1. DIMENSIONS D AND E DO NOT
INCLUDE MOLD PROTRUSION.

2. MAXIMUM MOLD PROTRUSION
FOR D IS 0.15mm.

3. MAXIMUM MOLD PROTRUSION
FOR E IS 0.25mm.

AZ10EP16VS
AZ100EP16VS

November 2001 * REV - 3 www.azmicrotek.com
9

Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc.
makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona
Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all
liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license
rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems
intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a
situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries,
affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly
or indirectly, any claim of personal injury or death associated with such unintended

or unauthorized use, even if such claim alleges tha

t

Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part.