Datasheet AZ100EL16VSTR1, AZ100EL16VST, AZ100EL16VSLR2, AZ100EL16VSLR1, AZ100EL16VSL Datasheet (AZMIC)

ARIZONA MICROTEK, INC.

AZ100EL16VS

ECL/PECL Differential Receiver with Variable Output Swing

FEATURES

• 250ps Propagation Delay

• High Bandwidth Output Transitions

• 75kΩ Internal Input Pulldown Resistors

• Functionally Equivalent to ON

Semiconductor MC100EL16

• Variable Output Swing

• Available in a 3x3mm MLP Package

PACKAGE PART NO. MARKING

MLP 8 AZ100EL16VSL AZM16P MLP 8 T&R AZ100EL16VSLR1 AZM16P MLP 8 T&R AZ100EL16VSLR2 AZM16P SOIC 8 AZ100EL16VSD AZM100EL16VS SOIC 8 T&R AZ100EL16VSDR1 AZM100EL16VS SOIC 8 T&R AZ100EL16VSDR2 AZM100EL16VS TSSOP 8 AZ100EL16VST AZH16VS TSSOP 8 T&R AZ100EL16VSTR1 AZH16VS TSSOP 8 T&R AZ100EL16VSTR2 AZH16VS

PACKAGE AVAILABILITY

DESCRIPTION

The AZ100EL16VS is a differential receiver with variable output swing. The EL16VS has functionality and output transition times similar to the EL16, with an input that controls the amplitude of the Q/Q¯ outputs. Maximum swing is achieved by leaving the V

The operational range of the EL16VS control input, V Simple control of the output swing can be obtained by a variable resistor between the V wiper driving V

The EL16VS provides a V For single-ended input applications, the V pair. The input signal is then fed to the other D/D¯ input. The V When used, the V

Under open input conditions (pulled to V NOTE: Specifications in ECL/PECL tables are valid when thermal equilibrium is established.

. Typical application circuits and results are described in this Data Sheet.

CTRL

BB

pin should be bypassed to ground via a 0.01µF capacitor.

BB

pin open or tied to VEE.

CTRL

, is from VBB (full swing) to VCC (min. swing).

CTRL

output for single-ended use or a DC bias reference for AC coupling to the device.

reference should be connected to one side of the D/D¯ differential input

BB

pin can support 1.0mA sink/source current.

BB

) internal input clamps will force the Q output LOW.

EE

and VCC pins, with the

BB

1630 S. STAPLEY DR., SUITE 125 • MESA, ARIZONA 85204 • USA • (480) 962-5881 • FAX (480) 890-2541

www.azmicrotek.com

AZ100EL16VS

LOGIC DIAGRAM AND PINOUT ASSIGNMENT

V

CTRL

8

V

CC

7

V

CTRL

1

8

V

CC

1

D

Q

6

2

D

7

Q

2

D

5

Q

3

D

6

3

V

BB

8 MLP (TOP VIEW)

Absolute Maximum Ratings are those values beyond which device life may be impaired.

Symbol Characteristic Rating Unit

VCC PECL Power Supply (VEE = 0V) 0 to +8.0 Vdc

VI PECL Input Voltage (V

VEE ECL Power Supply (VCC = 0V) -8.0 to 0 Vdc

VI ECL Input Voltage (VCC = 0V) -6.0 to 0 Vdc

I

OUT

TA Operating Temperature Range -40 to +85

T

STG

Output Current --- Continuous

--- Surge

Storage Temperature Range -65 to +150

4

V

EE

V

PIN DESCRIPTION

PIN FUNCTION

D, D¯ Data Inputs V

Output Swing Control

CTRL

Q, Q¯ Data Outputs VBB Reference Voltage Output V

CC

Positive Supply

= 0V) 0 to +6.0 Vdc

EE

BB

4

8 SOIC & 8 TSSOP

50

100

5

mA

°C °C

V

EE

100K ECL DC Characteristics (V

Symbol Characteristic

VOH Output HIGH Voltage2 -1085 -880 -1025 -880 -1025 -955 -880 -1025 -880 mV

VOL

VIH Input HIGH Voltage -1165 -880 -1165 -880 -1165 -880 -1165 -880 mV VIL Input LOW Voltage -1810 -1475 -1810 -1475 -1810 -1475 -1810 -1475 mV VBB Reference Voltage -1420 -1260 -1420 -1260 -1420 -1260 -1420 -1260 mV

IIH

IIL IEE Power Supply Current 18 25 18 25 18 25 21 26 mA

1. If V

2. Each output is terminated through a 50Ω resistor to V

Output LOW Voltage V

= V

CTRL

= V

BB

CC

Output LOW Voltage V

Input HIGH Current

Input LOW Current 0.5 0.5 0.5 0.5

is Open Circuit, use the VOH (Max & Min) and VOL (V

CTRL

2

1

2

D, D¯

V

CTRL

= -4.2V to -5.5V, VCC = GND; V

EE

-40°C 0°C 25°C 85°C

Min Typ Max Min Typ Max Min Typ Max Min Typ Max

-1890 -1620 -1870 -1680 -1870 -1775 -1680 -1870 -1680 mV

-1180 -975 -1135 -990 -1135 -1065 -990 -1135 -990 mV

– 2V.

CC

150

40

= V

CTRL

: Max only) limits.

REF

CTRL

150

40

= VBB)

150

40

150

40

Unit

µA µA

October 2001 * REV - 2 www.azmicrotek.com 2

yp

AZ100EL16VS

100K PECL DC Characteristics (V

Symbol Characteristic

VOH Output HIGH Voltage

VOL

Output LOW Voltage V

CTRL

Output LOW Voltage V

CTRL

= V

2

BB

CC

1,3

3915 4120 3975 4120 3975 4045 4120 3975 4120 mV

1,3

= GND, VCC = +5.0V)

EE

-40°C 0°C 25°C 85°C

Min T

Max Min T

Max

Unit

3110 3380 3130 3320 3130 3225 3320 3130 3320 mV

3820 4025 3865 4010 3865 3935 4010 3865 4010 mV

VIH Input HIGH Voltage1 3835 4120 3835 4120 3835 4120 3835 4120 mV VIL Input LOW Voltage1 3190 3525 3190 3525 3190 3525 3190 3525 mV VBB Reference Voltage1 3580 3740 3580 3740 3580 3740 3580 3740 mV

IIH

IIL

Input HIGH Current

D, D¯

V

CTRL

150

40

Input LOW Current 0.5 0.5 0.5 0.5

150

40

150

40

150

40

µA µA

IEE Power Supply Current 18 25 18 25 18 25 21 26 mA

1. For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value.

2. If V

is Open Circuit, use the VOH (Max & Min) and VOL (V

CTRL

3. Each output is terminated through a 50Ω resistor to V

– 2V.

CC

CTRL

= V

: Max only) limits.

REF

AC Characteristics (V

Symbol Characteristic

t

PLH

t

SKEW

V

PP

V

CMR

tr / tf

1. Duty cycle skew is the difference between a t

2. V

3. The V

Input to Output Delay

/ t

PHL

Duty Cycle Skew1 (Diff) 5 5 20 5 20 5 20 ps

(AC) Minimum Input Swing2 150 150 150 150 mV

Common Mode Range3

Rise/Fall Time 20 – 80%

is the minimum peak-to-peak differential input swing for which AC parameters are guaranteed.

PP

range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within

CMR

the specified range and the peak-to-peak voltage lies between V

= -4.2V to -5.5V; VCC =GND or VEE =GND; VCC = +4.2V to +5.5V)

EE

-40°C 0°C 25°C 85°C

Min Typ Max Min Typ Max Min Typ Max Min Typ Max

(Diff)

(SE)

V

CC

2.0

-

250 250

VCC -

175 125

VCC -

0.4

2.0

250 250

VCC -

325 375

0.4

175 125

VCC -

250 250

VCC -

2.0

100 350 100 350 100 350 100 350 ps

and t

PLH

propagation delay through a device.

PHL

(min) and 1V.

PP

325 375

0.4

205 155

VCC -

2.0

280 280

VCC -

355 405

0.4

Unit

ps

V

October 2001 * REV - 2 www.azmicrotek.com 3

AZ100EL16VS

100

Typical Voltage Output Swing at +25C, VEENom (see Figure 1 and

Figure 2)

1.500 V (100K ECL)

75

50

(% pk-pk differential)

25

SWING

V

0

0.0 0.4 0.8 1.2 1.6

V

(V)

CTRL

Vbb

1.320

Figure 1: Voltage Source Implementation

V

CTRL

V

CTRL

V

BB

1

2

D

3

D

4

8

V

CC

Q

7

Q

6

5

V

EE

50

V SW ING

(pk-pk)

50

-2V

%OUT

Vbb

100K ECL

Figure 2: Alternative Implementation

+5 V

10k

V

CTRL

V

BB

1

2

D

3

D

4

8

V

CC

Q

7

Q

6

5

V

EE

240

V SWING

(pk-pk)

October 2001 * REV - 2 www.azmicrotek.com 4

N

AZ100EL16VS

PACKAGE DIAGRAM

SOIC 8

MILLIMETERS INCHES

OTES:

1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION.

2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm.

3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm.

DIM

A A1 A2 A3 bp

c D E

e

HE

L

Lp

Q

v w

y Z

θ

MIN MAX MIN MAX

12.32 12.57 0.485 0.495

0.10 0.25 0.004 0.010

1.25 1.45 0.049 0.057

0.25 0.01

0.36 0.49 0.014 0.019

0.19 0.25 0.0075 0.0100

4.8 5.0 0.19 0.20

3.8 4.0 0.15 0.16

1.27 0.050

5.80 6.20 0.228 0.244

1.05 0.041

0.40 1.00 0.016 0.039

0.60 0.70 0.024 0.028

0.25 0.01

0.10 0.004

0.30 0.70 0.012 0.028

O

8

0

O

0

O

8

October 2001 * REV - 2 www.azmicrotek.com 5

O

N

AZ100EL16VS

PACKAGE DIAGRAM

TSSOP 8

MILLIMETERS

OTES:

1. DIMENSIONS D AND E DO NOT INCLUDE MOLD PROTRUSION.

2. MAXIMUM MOLD PROTRUSION FOR D IS 0.15mm.

3. MAXIMUM MOLD PROTRUSION FOR E IS 0.25mm.

DIM

A A1 A2 A3 bp

D

E

HE

L Lp

w

Z

θ

MIN MAX

1.10

0.05 0.15

0.80 0.95

0.25 0.45

c

0.15 0.28

2.90 3.10

e

4.70 5.10

0.40 0.70

v

y

0.35 0.70

O

6

0

0.25

0.65

0.94

0.10

O

October 2001 * REV - 2 www.azmicrotek.com 6

N

AZ100EL16VS

PACKAGE DIAGRAM

MLP 8

OTES

1. DIMENSIONING AND TOLERANCING CONFORM TO ASME T14-1994.

2. THE TERMINAL #1 AND PAD NUMBERING CONVENTION SHALL CONFORM TO JESD 95-1 SPP-012.

3. DIMENSION b APPLIES TO METALLIZED PAD AND IS MEASURED BETWEEN 0.25 AND 0.30mm FROM PAD TIP.

4. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS.

MILLIMETERS

DIM

A A1 A3

b

D D2

E E2

e

L

aaa

bbb

ccc

MIN MAX

0.80 1.00

0.00 0.05

0.25 REF

0.30 0.35

2.90 3.10

1.65 1.95

2.90 3.10

1.65 1.95

0.65 BSC

0.35 0.45

0.25

0.10

October 2001 * REV - 2 www.azmicrotek.com 7

t

AZ100EL16VS

Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc. makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona Microtek, Inc. assume any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license rights nor the rights of others. Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems intended to support or sustain life, or for any other application in which the failure of the Arizona Microtek, Inc. product could create a situation where personal injury or death may occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges tha Arizona Microtek, Inc. was negligent regarding the design or manufacture of the part.

October 2001 * REV - 2 www.azmicrotek.com 8